Lifestyler 831287420 Owner’s Manual

total body

workout • adjustable

8EARS

Model No. 831.287420 Serial No.

Write the serial number in the space

above for future reference.

Serial Number Decal

resistance

USER'S MANUAL

EXERCISE

E(:;_ U I P M E NT

HELPLINE!

1-800-736-6879

Patent Pending

SEARS, ROEBUCK AND COo, HOFFMAN ESTATE_, I_ 1_017_1

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS .............................................................. 2

BEFORE YOU BEGIN ................................................................... 3

ASSEMBLY ........................................................................... 3

ADJUSTMENT AND OPERATION ........................................................... 6

MAINTENANCE AND TROUBLE-SHOOTING . ."................................................ 8

CONDITIONING GUIDELINES ............................................................. 9

PART LIST ........................................................................... 10

EXPLODED DRAWING ............................. "..................................... 11

ORDERING REPLACEMENT PARTS ............................................... .Back Cover

WARRANTY .......................................................... _........ Back Cover

BEFORE YOU BEGIN

Thank you for selecting the innovative SEARS

LIFESTYLEFP CARDIO FORCE. The CARDIO FORCE offers a unique form of low-impact exercise that uses

both the upper body and the lower body for increased cardiovascular benefits and greater toning results.

For your benefit, read this manual carefully before

you use the CARDIO FORCE. If you have additional

ASSEMBLY

Place all parts of the CARDIO FORCE in a cleared area and remove the packing materials. Do not dis-

pose of the packing matedals until assembly is com- pleted. Read each step carefully before beginning.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

• one phillips screwdriver

• one adjustable wrench

• one rubber mallet

questions, please call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m.

until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number

and serial number when calling. The model number is

831.287420. The serial number can be found on a decal attached to the CARDIO FORCE (see the front

cover of this manual).

• the included pedal tool (see the drawing below).

PART CHART

Use the drawings below to identify the small parts used in assembly. The number in parenthesis below each drawing refers to the key number of the part. The

second number indicates the quantity needed for assembly. Note: Some small parts may have been pre-

attached for shipping purposes. If a part is not found in the parts bag, check to see if it has been pre-attached.

3/4" x 2" Pedal Tool--1

3/8" Nylon Locknut (33)---4 1/4" x 2" Screw (17).--2

1/2" Push Nut (30).--2 Note: Extra Push Nuts

may have been included.

1/2" Dome Cap (29)--4 Note: One extra Dome Cap

may have been included.

3/8" x 2 7/8" Carriage Bolt (35)--4

#6 x 3/8" Screw (16)--2

1. Find the Front Stabilizer (36), which has a decal on it.

Make sure that there is a Large Round Endcap (8) on each end of the Front Stabilizer.

Attach the Front Stabilizer (36) to the Frame (6) with two 3/8" x 2 7/8" Carriage Bolts (35) and 3/8" Nylon

Locknuts (33). Make sure that the indented holes in

the Front Stabilizer are turned toward the frame.

Attach the Rear Stabilizer (32) to the Frame (6) in the same manner.

2. Plug the Sensor Wire (15) into the back of the Monitor (1). Attach the Monitor to the bracket on the Frame (6)

with the two #6 x 3/8" Screws (16). Make sure that the Sensor Wire is not pinched between the

Monitor and the Frame.

3. IMPORTANT NOTE: Before assembling the 1/2"

Dome Caps (29) in steps 3 and 4, be sun that all parts are oriented as shown in the drawings. The Dome Caps can be used only once; if the Dome Caps must be removed, it will be necessary to order new Dome Caps.

Make sure that there are two 1/2" Pivot Bushings (20) in the indicated bracket on the Pedal Frame (7). Hold

the Pedal Frame so the bracket is between the holes

near the upper end of the Frame (6). Tap the 6" Pivot Rod (21) through the Pedal Frame and the Frame. Tap

a 1/2" Dome Cap (29) onto each end of the Pivot Rod.

4. Make sure that there is a 112"LinkArm Bushing (19) in the end of each Link Arm (4) (see the inset draw- ing). Align the ends of the Link Arms with the indicated

bracket on the Pedal Frame (7). Insert the 1 3/4" Rod (22) through the Link Arms and the bracket. Tap a 112"

Dome Cap (29) onto each end of the Rod.

5. Attach the Seat (3) to the Seat Tube (5) with the two 1/4" x 2" Screws (17). Be sure that the Seat is oriented

as shown.

6. Apply a small amount of grease to the two indicated shafts of the Pedal Frame (7). Slide a Pedal (12) onto the right shaft. Make sure that the Pedal is turned so the

plastic tube is facing the Pedal Frame, as shown. Using the included pedal tool, tap a 1F2"Push Nut (30) onto the

end of the shaft. Be sure that the Push Nut isturned as shown in the inset drawing.

Attach the other Pedal (12) (not shown) to the left shaft of the Pedal Frame (7) in the same manner.

Plastic

Note: Extra 1/2" Push Nuts (30) may have been includ- ed. Save the Push Nuts and the pedal tool in case

replacement Push Nuts are needed in the future.

7. Before using the CARDIO FORCE, check the Magnet

(18) and the Reed Switch (15), Pivot the Pedal Frame (7) until the Magnet is aligned with the Reed Switch

(see the inset drawing). Loosen the indicated #8 x 3/4"

Screw (27). Adjust the position of the Reed Switch so that there is a 1/8" gap between the Magnet and the

Reed Switch. Retighten the Screw.

Make sure that all parts of the CARDIO FORCE are propedy tightened.

Pedal Tool

+ 9 hidden pages