LifeSpan GS5, GS5 GYM MULTI STATION User Manual
NOTE: This manual may be subject to updates or changes. Up to date manuals are available through our website at www.lifespanfitness.com.au
Product may vary slightly from the item pictured due to model upgrades
Read all instructions carefully before using this product. Retain this owner’s manual for
future reference.
GS5 GYM MULTI
STATION USER MANUAL
2
GS5 GYM MULTI STATION
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS 3
2. ASSEMBLY INSTRUCTIONS 4
3. PARTS LIST 32
4. WARRANTY 34
3
GS5 GYM MULTI STATION
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this machine.
Install the product on a flat level surface
Place your unit on a solid, level surface when in use
Never allow children on or near the machine.
Keep hands away from all moving parts.
Never drop or insert any object into any openings.
Care must be taken when lifting or moving the equipment so as not to injure your back. Always use
proper lifting techniques and/or seek assistance if necessary.
Keep children and pets away from the machine at all times. DO NOT leave children unattended in
the same room with the machine.
Only one person at a time should use the machine.
If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the
workout at once. CONSULT A PHYSICIAN IMMEDIATELY
Do not use the machine near water or outdoors.
Keep hands away from all moving parts.
Always wear appropriate workout clothing when exercising. DO NOT wear robes or other clothing
that could become caught in the machine. Running or aerobic shoes are also required when using
the machine.
Use the machine only for its intended use as described in this manual. DO NOT use attachments not
recommended by the manufacturer.
Do not place any sharp objects around the machine.
Disabled person should not use the machine without a qualified person or physician in attendance.
Never operate the machine if the machine is not functioning properly.
A spotter is recommended during exercise.
4
GS5 GYM MULTI STATION
2. ASSEMBLY INSTRUCTIONS
5
GS5 GYM MULTI STATION
6
GS5 GYM MULTI STATION
7
GS5 GYM MULTI STATION
Tools required for assembling the machine: Two Adjustable Wrenches, two Allen Wrenches, and one
Philips Screwdriver.
Note: It is strongly recommended this machine to be assembled by two or more people to reduce
chance of injury.
STEP 1
1. Attach the Front Vertical Frame (#3) to the Main Base Frame (#8).Secure it with two
M10x70mm Carriage Bolts(#77), one 140x51mm bracket (#25), two φ10 washers (#80), and
two M10 Aircraft Nuts (#82). DO NOT tighten all the nuts and bolts yet.
2. Push two φ2 ½” Guide Rod Rubber Bumpers (#62) onto the Guide Rods (#20).Secure it with
two M10x25mm Allen Bolts (#70) and two φ10 Washers (#80) from the bottom of the Rear Base
Frame (#2).
3. Connect the Main Base Frame (#8) to the Rear Base frame (#2). Secure it with two M10x70mm
carriage bolts (#77), one rear base frame bracket (#26), two φ10washers (#80). And two M10
Aircraft Nuts (#82).
8
GS5 GYM MULTI STATION
9
GS5 GYM MULTI STATION
STEP 2
1. Slide the 14 Weight Plates (#29) onto the Guide Rods (#20). Align the holes of the Weight
Plates. Insert the Selector Rod (#13) through the centre hole. Use the L-shaped Pin (#30) to
select the number of plates.
2. Slide the Selector Stem (#28) onto the Guide Rods (#20).
3. Attach the Upper Frame (#4) onto the Guide Rods (#20). Place the Upper Frame (#4) onto the
Front Vertical Frame (#3).
4. Secure the Upper Frame to the Guide Rods with two M10x25mm Allen Bolts (#70) and two
φ10Washers (#80).
5. Secure the Upper Frame (#4) to the Front Vertical Frame (#3) with two M10x90mm Carriage
Bolts (#76), one 140x51mm Bracket (#25), two φ10Washers (#80), and two M10 Aircraft Nuts
(#82). Tighten all bolts and nuts previously installed.
10
GS5 GYM MULTI STATION
11
GS5 GYM MULTI STATION
STEP 3
1. Attach the Right Upright (#117) and Left Upright (#131), to the Upper Frame (#4). Secure with
two Carriage Bolts M10x90mm (#76), two Aircraft Nuts (#82) and two φ10 washers (#80).
2. Attach the Right Upright (#117) and Left Upright (#116) to the two lower tubes (#92) and (#94).
Four Carriage Bolts M10x70mm (#77), two Brackets (#25), four Aircraft Nuts (#82) and four
φ10washers (#80).
3. Attach the two Handles (#118, #119) to the Right Upright (#117), secured with two M10x70mm
Carriage Bolts (#77).
Loading...