Congratulations on your decision to purchase a Lifesmart spa.
Welcome to the growing family of Lifesmart spa owners!
Pre-Delivery Guide
Please take the time to read this booklet carefully, as it will provide you with the information you will need to ensure
the safe, secure, and timely installation of your new spa. The following sections are guidelines on how to prepare for
delivery and set-up of your new spa. Specifically covered are site selection, delivery access, ground preparation, and
electrical requirements.
Remember to carefully review the Owner’s Manual that accompanies your spa, The Owner's Manual can be found
in the Owner’s Package.
Watkins Wellness™ reserves the right to change features, specifications, and design without notification and without
incurring any obligation.
DATE PURCHASED: _________________________________________________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of
exterior surfaces (decks and gazebos). In addition, some communities have adopted residential barrier codes which
may require fencing and/or self-closing gates on the property to prevent unsupervised access to a pool (or spa) by
children under 5 years of age. Your spa is equipped with a locking cover that meets the ASTM F1346-91 Standard
for Safety Covers and as a result, is usually exempt from most barrier requirements. As a general practice, your local
Building Department will inform you of any applicable barrier requirements at the time a permit is obtained for the
installation of an electrical circuit.
For Customer Service, please call (888) 961-7727
Site Selection and Preparation
IMPORTANT: Site selection and preparation are your responsibility. Carefully read these instructions and consult
your authorized dealer if you have any questions.
You probably have a spot picked out for your new spa, whether it’s indoors or outdoors, on a patio or on a deck.
Just make sure you check the following:
• Always put your spa on a structurally sound, level within ½" per 10' (1 cm per 3 m) surface. A filled spa can
weigh hundreds of pounds. Make certain that the location you choose can support the weight of your filled
spa.
• Locate your equipment compartment, which houses all of the electrical components, in a place where water
will drain away from it. Allowing water into the equipment compartment can damage the electronics, or may
result in tripping your house’s circuit breaker.
• Leave yourself easy access to the circuit breakers in the subpanel (230 volt models), or to the GFCI on the
end of the power cord (110 volt models).
• Never let water get into the subpanel (230 volt models), or into the GFCI (110 volt models), or into the
electrical outlet that your spa is plugged into.
• Leave access to the equipment compartment for periodic spa care and maintenance.
OUTDOOR AND PATIO INSTALLATION
No matter where you install your new spa, it’s important that you have a solid foundation to support it. Structural
damage to the spa resulting from incorrect installation or placement on an inadequate foundation is not covered
under the spa’s limited warranty.
If you install the spa outdoors, a reinforced concrete pad at least four inches (10 cm) thick is suggested. The
reinforcing rod or mesh in the pad should be attached to a bond wire. All spas may be installed onto a deck,
provided that the load capacity of the deck is greater than the dead weight of the spa.
DECK INSTALLATION
To be certain your deck can support your spa, you must know the deck’s maximum load capacity. Consult a
qualified building contractor or structural engineer before you place the spa on an elevated deck or indoors.
To find the weight of your spa, its contents and occupants, refer to the Spa Specification chart on the inside back
cover of this guide. The weight per square foot must not exceed the structure’s rated capacity, or serious structural
damage could result.
INDOOR INSTALLATION
Be aware of some special requirements if you place your spa indoors. Water will accumulate around the spa, so
flooring materials must provide a good grip when wet. Proper drainage is essential to prevent a build-up of water
around the spa. When building a new room for the spa, it is recommended that a floor drain be installed. The
humidity will naturally increase with the spa installed. Water may get into woodwork and produce dry rot, mildew, or
other problems. Check for airborne moisture’s effects on exposed wood, paper, etc. in the room. To minimize these
effects, it is best to provide plenty of ventilation to the spa area. An architect can help to determine if more ventilation
must be installed.
x Page x xPre-Delivery Guide Page 2
GROUND PREPARATION
CONCRETE PADS
BRICK SURFACES
WOOD DECKING
FOUNDATIONS FOR SPAS
WITH ACCESSORIES
Your spa has been engineered to perform on all kinds of common yard surfaces. While a concrete slab is best
for long-term use*, other foundations are acceptable so long as a level base is prepared prior to delivery. Three
foundation base pictures, shown at right, represent examples of alternatives to a concrete slab for spas installed
without gazebos or other accessories.
NOTE: A reinforced concrete pad at least four inches (10 cm) thick is recommended.
INSTALLATION NOTES:
As a homeowner, it is your responsibility to provide a suitable, level
foundation for your spa. Keep in mind that most delivery crews are not
equipped to level and prepare spa sites.
If you are interested in having a concrete slab, brick surface, or wood
deck installed, your dealer should be able to suggest a qualified,
licensed contractor.
NOTE: In order for the spa to operate properly and the internal
plumbing to drain completely, you must ensure that the spa is leveled
within ½" per 10' (1 cm per 3 m) after it has been installed. Do not
shim you spa in any manner, as this could cause the cabinet to warp,
thereby voiding the warranty.
x Page x x
Page 3 Pre-Delivery Guide
x Page x x
DELIVERY
How is your width clearance?
Protruding electric meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
Is the path clear?
Move away branches, dog
houses, firewood, etc.
If there is a 90 turn, can we
clear it? (The spa will not bend)
No more than 6 consecutive
stairs without a landing
Gas meters
Check all gates
HOUSE
BACK YARD
STREET
Your spa will be delivered at the end of your driveway. It is delivered on end, wrapped on a sturdy pallet for
convenient placement. You will be responsible for any arrangements needed to have your spa placed in your
desired location. When the freight company calls to set up a delivery appointment, you may inquire if they are able
to assist. There may be an additional fee that you need to work out with the freight company.
(For example, cranes are not considered "normal delivery".) It is recommended to consulting professionals who have
experience moving large items.
Your spa will be delivered in approximately 2 - 4 weeks from the date of order. If you are unable to accept delivery
within this lead time, your spa order will be cancelled. Carriers are unable to hold and store your spa.
REVIEW THE ROUTE OF YOUR SPA DELIVERY:
Carefully review the route that the spa will take through your property. Make sure there is sufficient clearance. Keep
the overall dimensions in mind when your spa is wrapped on a pallet. You are able to remove the hot tub from the
pallet and put a 4-wheel furniture dolly underneath it to move it. In this case you will need a 3 ft wide pathway that
will accommodate an approximate 7' - 7½' height clearance. Keep in mind that it will be almost 7' long, so check for
clearances when turning corners.
NOTE: The empty spa can weigh as much as 1,000 lbs. Choose the safest and most direct route possible. We
recommend hiring professionals to avoid physical harm or property.
How is your width clearance?
x Page x x
x Page x x
Pre-Delivery Guide Page 4
LS100/DX
Banicia
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
Front View
Bottom View
ELECTRICAL
DRAIN
70” (178 cm)
45.5” (116 cm)
47” (119 cm)
18” (46 cm)
21” (53 cm)
26” (66 cm)
4”
(10 cm)
1.5”
(3.8 cm)
61” (155 cm)
32” (81.3 cm)
DOOR SIDE
x Page x x
Page 5 Pre-Delivery Guide
Front View
Calavera
LS200
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
21” (53 cm)
4”
(10 cm)
29” (73.6 cm)
Bottom View
DRAIN
ELECTRICAL
49” (125 cm)
66” (168 cm)
40” (101 cm)
12” (31 cm)
22” (56 cm)
1.5”
(3.8 cm)
77” (195.5 cm)
DOOR SIDE
x Page x x
Pre-Delivery Guide Page 6
Front View
LS300
60” (152 cm)
66” (168 cm)
1”
(2.5 cm)
23” (58 cm)
ELECTRICAL
DRAIN
31” (79 cm)
98” (249 cm)
67” (170 cm)
33” (84 cm)
3.5”
(9 cm)
30” (76 cm)
72” (183 cm)
LS300 PLUS
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
Bottom View
DOOR SIDE
x Page x x
Page 7 Pre-Delivery Guide
LS350DX/PLUS
LS350 DX
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
Front View
Bottom View
DRAIN
ELECTRICAL
81” (206 cm)
51” (130 cm)
52” (132 cm)
25” (63.5 cm)
26” (66 cm)
27” (69 cm)
4”
(10 cm)
1.5”
(4 cm)
72” (183 cm)
34” (86 cm)
DOOR SIDE
x Page x xx Page x xPre-Delivery Guide Page 8
Front View
Verona
LS450DX
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
24” (61 cm)
3”
(8 cm)
34” (86.4 cm)
Bottom View
ELECTRICAL
DRAIN
53” (135 cm)
81” (205.7 cm)
51” (130 cm)
21” (53 cm)
25” (63.5 cm)
1.5”
(3.8 cm)
81” (205.7 cm)
DOOR SIDE
x Page x xx Page x x Page 9 Pre-Delivery Guide
Aryana
27” (69 cm)
55” (140 cm)
58” (147 cm)
1.5”
(3.8 cm)
26” (66 cm)
ELECTRICAL
DRAIN
34” (86.4 cm)
77” (195.5 cm)
87” (221 cm)
24.5” (62 cm)
4”
(10 cm)
Front View
LS500/550
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
Bottom View
DOOR SIDE
x Page x xPre-Delivery Guide Page 10
Front View
LS600DX
NOTE: The
LS700 has a
secondary door
not illustrated
LS600/700
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
24” (61 cm)
3”
(7.6 cm)
34” (86.4 cm)
Bottom View
DRAIN
ELECTRICAL
81” (205.7 cm)
52” (132 cm)
54” (137 cm)
21.25” (54 cm)
25” (63.5 cm)
1.5”
(3.8 cm)
81” (205.7 cm)
DOOR SIDE
x Page x x Page 11 Pre-Delivery Guide
Front View
Transport
SERENO
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
34” (86.4 cm)
27” (68.6 cm)
4”
(10 cm)
Bottom View
ELECTRICAL
7” (18 cm)
8” (21 cm)
38” (96.5 cm)
39” (99 cm)
DRAIN
75” (190.5 cm)
1”
(2.5 cm)
75” (190.5 cm)
DOOR SIDE
x Page x xPre-Delivery Guide Page 12
48.5” (123 cm)
Tierra
14” (36 cm)
20” (51 cm)
51” (130 cm)
56” (142 cm)
1”
(2.5 cm)
5”
(13 cm)
23” (58 cm)
ELECTRICAL
DRAIN
34” (86.4 cm)
77” (196 cm)
87” (221 cm)
Front View
TIERRA
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
Bottom View
DOOR SIDE
Pre-Delivery Guide Page 14
x Page x x
Carino
Front View
ELECTRICAL
CARINO
™
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
31” (79 cm)
6”
(15 cm)
36” (91.4 cm)
Bottom View
78” (198 cm)
89” (226 cm)
DRAIN
5.5” (14 cm)
21” (53 cm)
1.5”
(3.8 cm)
89” (226 cm)
ELECTRICAL
DOOR SIDE
Page 15 Pre-Delivery Guide
x Page x x
Miramar
Front View
ELECTRICAL
ESTRELLA
™
NL/L
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
31” (79 cm)
6”
(15 cm)
36” (91.4 cm)
Bottom View
DRAIN
73.5” (124 cm)
84” (213 cm)
5.5” (14 cm)
21” (53 cm)
1.5”
(3.8 cm)
84” (213 cm)
ELECTRICAL
DOOR SIDE
x Page x x
Pre-Delivery Guide Page 16
Playa
73” (185 cm)
1”
(2.5 cm)
25.5” (65 cm)
ELECTRICAL
DRAIN
29.5” (75 cm)
84” (213 cm)
65” (165 cm)
22” (56 cm)
6”
(15 cm)
5.5” (14 cm)
ELECTRICAL
Bottom View
Front View
PLAYA
™
Dimensions
NOTE: All dimensions are approximate; measure your spa
before making critical design or pathway decisions.
DOOR SIDE
Page 17 Pre-Delivery Guide
x Page x x
ELECTRICAL REQUIREMENTS
To ensure you will have an opportunity to use your spa soon after delivery, it is very important that the required
electrical service has been installed. THIS IS YOUR RESPONSIBILITY.
IMPORTANT: All electrical circuits must be installed by a qualified, licensed electrician.
Some spa models are available as 110 volt or 230 volt convertible heating systems. These models come standard
from the factory with 110 volt heating systems; however, with the addition of a subpanel and a control box wiring
change, they can be converted to 230 volt operation. See the following sections for the electrical requirements for
110 volt operation, and 230 volt converted operation.
110 VOLT 15 AMP OPERATION REQUIREMENTS
Sereno & Fantasia Models: The heater will provide approximately 1000 watts of heat only when the pump is
operating in LOW speed and the thermostat is calling for heat. NOTE: The heater does not operate when the pump
is on high speed.
It is highly recommended that the 110 volt spa models be on a dedicated 15 amp, 110 volt circuit.
All 110 volt models come equipped with approximately 13 feet (4 m) of usable power cord. (This is the maximum
length allowed by ETL.) When the spa is installed, the power cord will come out of the bottom of the equipment
compartment.
In addition to the dedicated 15 amp, 110 volt GFCI protected circuit, your spa requires a 15 amp single receptacle.
This receptacle should contain an outdoor-rated, weather-resistant receptacle cover plate. The single receptacle
and cover plate should be installed by your electrician prior to the
delivery of your spa.
For your safety, when your electrician is installing the electrical
outlet, it should be no closer than five feet (1.5 m) and no farther
than ten feet (3 m) from the spa. (Reference National Electric Code
680-6a(1) and 680-41a.)
WARNING: Do not connect your spa to an extension cord!
The 110 volt GFCI switch and the receptacle must be protected
from weather and landscape sprinklers–they should never get wet.
Your spa has been carefully engineered to provide maximum safety
against electric shock. Remember, connecting the spa to an improperly wired circuit will negate many of its safety
features.
110 VOLT 30 AMP CONVERSION (SERENO ONLY)
Benefit when converting to a 30 amp system: The heater will provide approximately 1000 watts of heat when the
pump is operating in LOW or HIGH speed and the thermostat is calling for heat.
Converted models require a 30 amp, single phase, 110 volt circuit breaker in the main electrical service panel.
Converted spas must be wired in accordance with applicable local and national electrical codes. All electrical work
must be done by a licensed electrician.
NOTE:
THIS CONVERSION
THE SPA. The subpanel containing a GFCI breaker must be purchased separately.
REQUIRES THE USE OF A SUBPANEL TO SUPPLY POWER AND PROTECT
230 VOLT 50 AMP (CONVERTED SERENO )
Benefit when converting to a 230V 50 amp system: The heater will provide approximately 4000 watts of heat when
the pump is operating in LOW or HIGH speed and the thermostat is calling for heat.
All 230 volt models require a 50 amp, single phase, 230 volt circuit breaker in the main electrical service panel.
All 230 volt spas must be wired in accordance with applicable local and national electrical codes. All electrical work
must be done by a licensed electrician.
NOTE:
THIS CONVERSION
THE SPA. The subpanel containing a GFCI breaker must be purchased separately.
x Page x xx Page x x
Pre-Delivery Guide Page 18
REQUIRES THE USE OF A SUBPANEL TO SUPPLY POWER AND PROTECT
A licensed electrician should install a four-wire electrical service (two line voltages, one neutral, one ground) from
the main electrical service panel to the subpanel, and from the sub-panel to the spa per the appropriate wiring
diagram as illustrated below.
Your electrician should mount the subpanel in the vicinity of the spa but it should not be closer than five (5) feet
from the spa water edge (NEC 680-38 to 41-A-3).
INSTALLATION NOTE: After the spa has been installed, your electrician can connect the conduit from the
subpanel to the spa’s control box and then complete the wiring connections in the control box.
NOTE: Complete step-by-step Installation and Wiring Instructions for 230 volt configuration are included in the
Owner’s Manual and with each sub-panel.
WARNING: Removing or bypassing the GFCI breakers in the subpanel at any time will result in an unsafe spa and
will void the warranty.
WIRE SPECIFICATION NOTE: Long electrical runs may require a larger gauge feed wire than stated. All wiring
must be copper to ensure adequate connections. Do not use aluminum wire.
Refer to the Wiring Diagrams below for the electrical requirements of the 230 volt models.
230V Wiring Instructions:
4 Wires/Minimum 50 amp GFCI Breaker #8 AWG 75°C
Copper Wire Minimum (less than 100’ (30 m) length)
Special Note:
If the GFCI breaker trips immediately after attempting
to turn on, please check the White Neutral Wire that is
connected to the spa. See figure below.
White Neutral Wire that is connected to Spa Neutral goes HERE.
Red
White
Black
Green
From the House
Breaker Box
x Page x xx Page x x
Page 19 Pre-Delivery Guide
To the Spa
Spa Specifications
Spa Model
(Seating)
LS100/DX
(4 Person)
LS200
(4 Person)
LS300 PLUS
(3 Person)
LS350DX/PLUS
(5 Person)
(6 Person)
(5 Person)
(5 Person)
LS600DX
(7 Person)
(7 Person)
(4 Person)
TIERRA
(5 Person)
™
™
LS450DX
LS500 PLUS
LS550 PLUS
LS700DX
**SERENO
Footprint
Dimension
Height
Effective
Filter
Heater
(Watts)
Water
Capacity
Dry
Weight
Filled
Weight*
Area
5'10" x 5'1" 32" 50 ft²
6'5" x 5'6" 29" 25 ft²
6' x 6' 31" 50 ft²
6' x 6'9" 34" 50 ft²
6'9" x 6'9" 34" 50 ft²
7'3" x 6'5"
7'3" x 6'5"
6'9" x 6'9" 34" 50 ft² 4,000 290 gal 478 lbs 4,148 lbs
6'9" x 6'9" 34" 50 ft² 4,000
6'3" x 6'3" 34" 50 ft²
7'3" x 6'5" 34" 50 ft² 4,000 327 gal 426 lbs 4,058 lbs
34"
50 ft²
34"
50 ft² 4,000 290 gal 445 lbs 3,765 lbs
Heat
Recovery
Heat
Recovery
Heat
Recovery
Heat
Recovery
Heat
Recovery
Heat
Recovery
1,000
or
4,000
205 gal 270 lbs 2,698 lbs
220 gal 244 lbs 2,799 lbs
260 gal 405 lbs 2,947 lbs
315 gal 351 lbs 3,881 lbs
270 gal 440 lbs 3,766 lbs
290 gal 423 lbs 3,743 lbs
285 gal
245 gal 406 lbs 3,171 lbs
582 lbs 4,210 lbs
Electrical
Requirements
110 volt, 15 amp
GFCI protected
circuit
110 volt, 15 amp
GFCI protected
circuit
110 volt, 15 amp
GFCI protected
circuit
110 volt, 15 amp
GFCI protected
circuit
1110 volt, 15 amp
GFCI protected
circuit
110 volt, 15 amp
GFCI protected
circuit
230 volt 50 amp
GFCI protected
circuit
230 volt 50 amp
GFCI protected
circuit
230 volt 50 amp
GFCI protected
circuit
110 volt, 15 amp or
230 volt 50 amp
GFCI protected
circuit
230 volt 50 amp
GFCI protected
circuit
CAUTION: WATKINS WELLNESS suggests a structural engineer or contractor be consulted before the
spa is placed on an elevated deck.
* NOTE: The “Filled Weight” of the spa includes the weight of the occupants (assuming an average
occupant weight of 175 lbs).
** Spas may be converted to 110 Volts 30 amps requiring a 30 amp service.
x Page x xPre-Delivery Guide Page 20
Spa Specifications - Continue
Spa Model
(Seating)
ESTRELLA™ L
(6 Person)
ESTRELLA™ NL
(7 Person)
PLAYA
(3 Person)
CARINO
(6 Person)
Footprint
Dimension
Height
Effective
Filter
Heater
(Watts)
Water
Capacity
Area
7'0" x 7'0" 36" 50 ft² 4,000 330 gal 796 lbs 4,737 lbs
7'0" x 7'0" 36" 50 ft² 4,000 360 gal 700 lbs 4,960 lbs
™
7'0" x 5'5" 29.5" 35 ft² 4,000 210 gal 663 lbs 2,958 lbs
™
7'5" x 7'5" 36" 50 ft² 4,000 409 gal 893 lbs 5,433 lbs
Dry
Weight
Filled
Weight*
Electrical
Requirements
230 volt, 50 amp
GFCI protected
circuit
230 volt, 50 amp
GFCI protected
circuit
230 volt, 50 amp
GFCI protected
circuit
230 volt, 50 amp
GFCI protected
circuit
CAUTION: WATKINS WELLNESS suggests a structural engineer or contractor be consulted before the
spa is placed on an elevated deck.
* NOTE: The “Filled Weight” of the spa includes the weight of the occupants (assuming an average
occupant weight of 175 lbs).
x Page x x Page 21 Pre-Delivery Guide
1280 Park Center Drive
Vista, California 92081
(888) 961-7727
email: AHSService@watkinsmfg.com
©2021 WATKINS WELLNESS.
62910.21 A (1/21)
Loading...