Life Smart LS-PH08H User Instruction Manual
EElleeccttrriiccW
WaallllPPaanneellHHeeaatteerr
Model:LS‐PH08H
READ INSTRUCTIONS CAREFULLY:
safe place for future reference. Do not allow anyone who has not read these instructions
assemble, plug in, turn on, or operate the heater.
Read and follow all instructions. Place instructions in a
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of
fire, electric shock, and injury to persons, including the following:
1. Read all instructions before using this heater.
2. Extreme caution: This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
3. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front
of the heater and keep them away from the sides and rear.
4. Always unplug heater when not in use.
5. Do not operate the heater with a damaged cord or plug or after the heater malfunctions, has been dropped or
damaged in any manner. Return it to authorized service facility for examination, electrical or mechanical
adjustment, or repair.
6. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never place the
heater where it may fall into bathtub or other water receptacles.
7. Do not run cord under material. Do not cover cord with throw rugs, runners, or similar coverings.
8. To prevent a possible fire, do not block the space between the heater and the wall which is for air intake or
exhaust in any manner.
9. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stored.
10. Use this heater only as described in this manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.
11. If the supply cord is damaged, it must be replaced by the manufacturer, a service agent, or qualified
persons in order to avoid a hazard.
12. The heater must not be mounted over or directly above or below a power outlet.
13. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire.
14. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances
working. Do not install the heater under the wall socket.
15. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle)
and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or
worn outlet.
16. The output of this heater may vary and its temperature may become intense enough to burn exposed skin.
Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to
avoid burns.
17. WARNING: In order to avoid overheating, do not cover the heater.
18.SAVE THESE INSTRUCTIONS
Getting Started
1. Unpack your heater and any packing materials
2. If all items are enclosed, thoroughly Inspect the heater for any shipping damage (cracks, dents, broken
power buttons, etc.) prior to doing anything else. If it was damaged in transit, contact your place of
purchase immediately.
Included In the Box
1. Main Components:
· (Qty 1) Panel Heater
· (Qty 1) Instruction Manual
2. Mounting Hardware Pack Consisting of :
· (Qty 4) Plastic Mounting Posts w/ Built-In Wall Achor
· (Qty 1) Drill Bit
· (Qty 4) Long Mounting Screws
· (Qty 4) Plastic Screw Head Caps
Items Required For Mounting
2 People (to help hold it) · Mounting Hardware Pack · Power Drill · Medium Phillips Screwdriver · Small
Level · Pencil for marking the wall (if you think you may have to erase) or a Fine Tip Marker · Medium
Strength Glue (recommended but not essential)
Precautions Prior to Mounting
・
2 People will be required to complete the mounting process.
・
Keep all packaging and packaging materials until you have inspected the heater and all the contents of
the mounting hardware.
・
The mounting hardware pack contains small items that should be kept away from young children.
・
Do not plug in or power up the heater until it is secure to the wall and the instructions are read fully.
・
Please choose a mounting location wisely, prior to starting. A power outlet must be within the
cord’s reach, but the heater must not be mounted over or within 12 inches above or below the
outlet.
・
Please observe the recommended heights and dimensions for mounting the heater.
・
This appliance is designed to be mounted to a wall at a minimum height of 8 inches from the floor.
・
Take necessary precautions to avoid cutting or damaging any cables or power cords.
・
While drilling holes for the mounting posts, be cautious of electrical lines, metals, or items beyond the
walls.
・
Be sure that the wall you choose to mount on is solid, and will support the heater’s weight of
approximately 13 lbs.
・
Make sure that the heater is safely out of the way while you are installing mounting hardware, as it
may become a tripping hazard if left in the open.
・
Please be cautious if you are set on mounting the heater low to the floor, as it may become a
safety hazard to children and pets!
Mounting Instructions (Reference Fig 1-8 Next Page)
**Note: If you do not have a second person to assist, you may use the dimensions on Fig. 7 as a guide to
mounting without awkward handling of the heater.
1. Choose your mounting location based on the criteria in “Precautions Prior to Mounting.”
2. Make sure when choosing your mounting location, that the distance between the bottom of the heater
and the floor will be no less than 8 inches when the heater is installed
3. Once the mounting location is carefully picked out, and with assistance of a second person, lift the
heater, (with the flat side up against the wall) and straighten it using the small level.
4. Mark the positions of the four holes to be drilled on the wall with the pencil or marker (Ref. Fig 1).
5. At this point, lower the heater and place it where it will not be a tripping hazard.
6. Using the power drill, and the bit included in your mounting hardware kit, drill the marked holes on
the wall (Ref. Fig 2).
7. Insert the 4 plastic mounting posts into the holes. You should be able to press them in. If too difficult
to press, you may be able to lightly tap them in, using the screwdriver handle. (Ref. Fig 3)
8. Line up and slide the heater onto the 4 mounting posts the four holes in the heater (switch side towards
the wall). (Ref. Fig 4)
9. Once the heater is resting on the mounting posts, insert and tighten the screws onto the posts. (The
screwdriver is recommended to avoid stripping the posts or screw heads) (Ref. Fig 5)
10. Install the plastic end caps onto the heads of the screws. It is recommended to use a bit of medium
strength glue to hold each cap in place. (Extra strength glue or “crazy glue” is not recommended, in
case you need to remove in the future) (Ref. Fig 6).
11. Fig. 7 shows an outline of what the completed process should look like.
Loading...