Life Fitness IC2, IC-LFIC2B1-01 User Manual
ENG
MANUFACTURED BY:
Indoor Cycling Group GmbH
Happurger Str. 86
90482 Nuremberg | Germany
info@indoorcycling.com
www.indoorcycling.com
Phone: +49(0)911 / 54 44 50
ENG
CAUTION!
READ ALL PRECAUTIONS AND INSTRUCTIONS IN THIS MANUAL BEFORE YOU START
USING THIS EQUIPMENT. PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE.
IMPROPER ASSEMBLY, USE OR MAINTENANCE CAN VOID THE WARRANTY TERMS.
Version 1.1 2017 IC-LFIC2B1-01 Copyright by Indoor Cycling Group GmbH 2017 | www.indoorcycling.com
IC2
MODEL NO:IC-LFIC2B1-01
Version 1.1 2017 IC-LFIC2B1-01 Copyright by Indoor Cycling Group GmbH 2017 | www.indoorcycling.com
TECHNICAL SPECIFICATIONS:
The Life Fitness IC2 Bike is according to EN 957 a Class S product for professional
and / or commercial use. Such training equipment is intended for the use in training areas
of organizations such as tness clubs or sport associations, where access and control is
specially regulated by the person who has the legal responsibility.
WARNING!
The bike is designed to accommodate most users from
150 cm to 205 cm (4’11’’ to 6’ 9’) body height.
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS P.3
GETTING STARTED P.4
HOW TO ASSEMBLE THE INDOOR CYCLE P.5-7
INITIAL INSTALLATION CHECKS P.8-9
HOW TO ADJUST THE INDOOR CYCLE P.10-12
RESISTANCE ADJUSTMENT P.13
HOW TO MOVE THE INDOOR CYCLE P.13
PREVENTIVE MAINTENANCE P.14-18
MAINTENANCE ACTIVITY PLAN P.19
SPARE PARTS P.20
LIMITED WARRANTY P.21-22
FOOT PRINT: 53 X 115 CM / 20.9 X 45.3 INCH
WEIGHT OF BIKE: 48 KG / 106 LBS
MAX SADDLE HEIGHT: 116 CM / 45,7 INCH
MAX HANDLEBAR HEIGHT: 119 CM / 47 INCH
MAX USER WEIGHT: 130 KG / 287 LBS
3
ENG
1. It is the sole responsibility of the owner to
ensure that all users of the indoor cycle are
informed and aware of all warnings
and precautions.
2. Operate and maintain the indoor cycle
only as described in this manual and after
proper assembly and functionality check as
described in this manual.
3. Keep the indoor cycle indoors, away from
moisture and dust. Do not place the indoor
cycle in a garage or covered patio or near
water or pools.
4. Place the indoor cycle on a level surface.
To protect the oor or carpet from damage,
place a mat beneath the indoor cycle.
Make sure that there is adequate room (20
inches/0,5m) around the indoor cycle to
assemble, disassemble and operate it.
5. Regularly inspect and properly tighten all
parts of the indoor cycle as recommended in
this manual. Please replace defective parts
immediately and do not use the Bike until
repair is performed. Only use original parts
from the manufacturer.
6. Children under the age of 14 should
only be allowed use of the indoor cycle
with parental approval and supervision. If
the indoor cycle is not in use, please make
sure the brake resistance is fully engaged
to prevent drive gear components from
movement and to avoid the potential risk of
injury due to improper use.
7. The indoor cycle should not be used by
persons exceeding weight of 287 lbs/130 kg.
8. Always wear appropriate riding gear and
shoes for cycling while operating the indoor
cycle. Do not wear loose clothes or shoes
with loose laces which could become caught
on the indoor cycle.
9. Before using the indoor cycle, make sure
you are familiar with the setup/operation of
the indoor cycle.
10. The indoor cycle does have a direct
driven ywheel (wheel); the pedals will
continue to move along with the ywheel
until the ywheel stops.
11. Always regulate the ywheel resistance
so that your pedalling motion is controlled.
12. Keep your back straight while using the
indoor cycle; do not arch your back.
13. If you feel pain or dizziness while
exercising, stop immediately, rest and cool
down and consult a physician.
14. If replacement parts are needed, use only
manufacturer supplied parts.
IMPORTANT
PRECAUTIONS
WARNING!
To reduce the risk of serious injury, read the following
precautions and information carefully before
operating the indoor cycle.
WARNING!
Before beginning any exercise program, consult
your physician. This is especially important for
persons over the age of 35 or persons with pre-
existing health problems. Read all instructions
before using. Be aware that incorrect or extensive
training may result in serious health injuries.
The manufacturer assumes no responsibility for personal injury or
property damage related by or through the use of this product.
Version 1.1 2017 IC-LFIC2B1-01 Copyright by Indoor Cycling Group GmbH 2017 | www.indoorcycling.com
GETTING STARTED
DEAR CUSTOMER,
Congratulations for selecting the LIFE FITNESS IC2. The LIFE FITNESS indoor cycle oers an
impressive array of features designed to enhance cardiovascular tness, tone muscles, and
develop endurance. Whether users are beginners or experienced athletes, the LIFE FITNESS IC2
oers workouts that will help users to reach their individual tness goals.
IMPORTANT: Read this manual carefully before assembling or using the indoor cycle. If you have
questions after reading this manual, please contact your local distributor or refer to the website
www.indoorcycling.com. Before reading further, please familiarize yourself with the parts that
are labeled in the drawing below.
YOU WILL FIND THE PRODUCTION CODE ON THE LEFT SIDE OF THE LIFE FITNESS IC2 WITHIN THE LOWER
RANGE OF THE FRAME. PLEASE REGISTER THESE IN SERVICING AND MAINTENANCE LISTS.
EMERGENCY BRAKE & RESISTANCE KNOB
SADDLE
T- LOCK HANDLE
ADJUSTMENT KNOB
PEDAL /TOE CLIP
CHAIN GUARD
MAINTENANCE COVER
HANDLEBAR
ADJUSTMENT KNOB
BRAKE PAD
FLYWHEEL
TRANSPORT WHEEL
LEVELLING FEET
5
ENG
HOW TO ASSEMBLE THE
INDOOR CYCLE
2X 17MM
1X 13MM
15MM
PEDAL WRENCH
1X
5MM
2
PEOPLE
1. 2.
4.3.
ASSURE THAT PLASTIC GASKET IS PLACED BETWEEN
STABILIZER AND FRAME.
ASSURE THAT PLASTIC GASKET IS PLACED BETWEEN
STABILIZER AND FRAME. GASKET SHOULD NOT BE
VISIBLE ONCE ASSEMBLED.
ASSURE THAT BLACK RUBBER WASHER IS PLACED
BETWEEN UPPER FRAME AND BOLT/WASHER.
ASSURE THAT BLACK RUBBER WASHER IS PLACED
BETWEEN UPPER FRAME AND BOLT/WASHER.
7NM
Version 1.1 2017 IC-LFIC2B1-01 Copyright by Indoor Cycling Group GmbH 2017 | www.indoorcycling.com
HOW TO ASSEMBLE THE
INDOOR CYCLE
WARNING!
Make sure the seat is xed properly in
a LEVEL HORIZONTAL position and
securely tigthend from both sides!
5. 6.
STOP MARK
2X 17MM
1X 13MM
5MM
2
PEOPLE
7.
1X
15MM
PEDAL WRENCH
25NM
7
ENG
HOW TO ASSEMBLE THE
INDOOR CYCLE
8. 9.
STOP MARK
STOP MARK
STOP MARK
2X 17MM
1X 13MM
15MM
PEDAL WRENCH
1X
5MM
2
PEOPLE
11.
10.
WARNING!
Pedal marked R installed on right crank (clockwise). Pedal marked L installed on left crank (counter-clockwise)
Pedals must be fastened with signicant strength to avoid loosening with use of the LIFE FITNESS IC2.
55NM
18NM
Version 1.1 2017 IC-LFIC2B1-01 Copyright by Indoor Cycling Group GmbH 2017 | www.indoorcycling.com
INITIAL
INSTALLATION CHECKS
The cycle tune-up must be performed at initial installation of the LIFE FITNESS
IC2 for optimal performance and longevity. Please read and follow all instructions
below. If the LIFE FITNESS IC2 is not installed and tuned as described, components
may wear excessively and the LIFE FITNESS IC2 may become damaged. If you have
questions about the installation, please contact service@indoorcycling.com.
Note: Some maintenance procedures require acid-, silicone- and solvent free spray
lubricant (for example BRUNOX), and white lithium grease.
1. Make sure that the LIFE FITNESS IC2 is leveled. If the LIFE FITNESS IC2 rocks on the oor, turn
the leveling feet underneath the front and/or rear stabilizer until the rocking motion is elimina
ted.
2. Verify emergency brake function to assure that emergency brake functions correctly.
3. Brake pad calibration: Turn resistance knob counterclockwise as far as possible (minimum
braking eect), verify that there is a slight separation of the brake pad from ywheel. Brake pad
should barely touch the ywheel when resistance knob is turned counter-clockwise as far as it
can go.
4. Apply spray lubricant to the brake pad using the lubrication holes on the plastic part or the
brake pad and externally on the felt pad. Make sure brake pad is thoroughly soaked from end
to end with lubricant spray. Then, wipe the excess o from the ywheel.
* Best Practice: Use a rellable spray bottle lled with non-aerosol acid-, silicone- and
solvent free spray lubricant purchased by the gallon (3.7 L) at the local hardware store.
5. Apply lithium grease to the threads on the lower end of the brake rod. First, turn the resistance
knob clockwise until it stops. Apply a small amount of white lithium grease to the threads on
the brake rod above the two lock nuts. Then, turn the resistance knob counter-clockwise
until it stops.
Loading...