Life Fitness GS4 User Manual

LEG PRESS ADAPTER KIT

FOR GS4 GYM SYSTEM

WARNING:

Read and follow all directions
for each step to insure proper
assembly of this product.

CLASS H
PAR T # 7362701
REV. A

USER’S GUIDE

1

V ersion: GS4-LP5A-101

Revision: 11/01/02

j

TABLE OF CONTENTS

Safety Statement.............2

General Notes..................3

Tools Required................3

Parts list..........................4

Assembly Instructions.....4-11

Insert-Registration Card

IMPORTANT SAFETY INFORMATION

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF

EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!

1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.

2. Obtain a medical exam before beginning any
exercise program.

3. Keep body and clothing free of all moving objects.

4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or

ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.

6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.

7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.

8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.

5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.

9. Children must not be allowed near this machine.
Supervise teenagers.

.

NOTE: In a continual effort to improve our products, specifications are subject to change
2002 Life Fitness, a division of Brunswick Corporation. All rights reserved.

©

ParaBody is a trademark of Brunswick Corporation

www.parabody.com

2

IMPORTANT NOTES

Please note:

* Thank you for purchasing the ParaBody GS4 Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.

* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.

Tools Required for Assembly

* 9/16” wrench
* Ratchet with 9/16” socket
* Adjustable wrench
* T ape measure

Bolt Length Ruler

NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT .

BOLT LENGTH

BOLT LENGTH RULER:

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

3

6

PARTS LIST

KEY

1
2
3
4
5
6
7
8

NOTE: The LEG PRESS ATTACHMENT (LP5) must be assembled before connecting it to the PARABODY GS1/GS2 GYM

PART #

ACU04-1525
ACU04-1526
ACU02-0055
ACU13-0149

ACU06-0024
ACUDA1E03853416NB
ACUDA1E03843416NB
ACUDA1E03833416NB

SYSTEMS

DESCRIPTION

CONNECTING TUBE

PULLEY HOUSING

CABLE RET AINER

LEG PRESS CABLE 202-3/4

3-1/2 PULLEY

3/8” X 5-3/4” BOL T

3/8 X 4-3/4” BOL T

3/8” X 3-3/4” BOL T

QTY

1
1
1
1
7
2
5
2

KEY

9
10
11
12
13
14
15

PART #

ACUDA1E03823416NB
ACUDA1E03813416NB

ACUDC1250100020B
ACUDB2E03811000B

ACU08-0085
ACU08-0076
ACU08-0079

DESCRIPTION

3/8 X 2-3/4” BOL T
3/8 X 1-3/4” BOL T

3/8” W ASHER

3/8” LOCK NUT

STEP SP ACER 19/32”

STEP SP ACER 1-9/16”

STEP SP ACER 1-1 1/16”

QTY

2
3
9

14

4
4
2

FIGURE 1

REMOVE LOWER
PULLEY

1

DISCARD!
CABLE

STEP 1:

• Remove END CAP and the bolts attaching the FRAME BRACE and insert new CONNECTING TUBE (1) using same BOLTS and re­install endcap.

• Remove the LEG CABLE and the BOL T , NUT and WASHER used to secure CABLE to base. Discard CABLE

4

3/8 X 5-3/4”

6

2

11

12

FIGURE 2

STEP 2:

• Install PULLEY HOUSING (2) using two 3/8 X 5-3/4” BOL TS (6), four 3/8” W ASHERS (1 1) and two 3/8” LOCK NUTS (12)
as shown in FIGURE 2

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

5

6

1

3/8 X 3-3/4”

8

11

12

FIGURE 3

STEP 3:

• Assemble the new LEG PRESS to the CONNECTING TUBE (1) using two 3/8 X 3-3/4” BOL TS (8), four 3/8” WASHERS (11)

and two 3/8” LOCK NUTS (12) as shown in FIGURE 3

6

5

4(a)

CABLE GUIDE

5

12

3/8 X 1-3/4”

10

4(b)

2

FIGURE 4

STEP 4:

• Screw the threaded end of the LEG PRESS CABLE (4) into the end of the FLOA TING PULLEY BRACKET . Secure the CABLGUIDE
in place with the JAM NUT on the GUIDE CABLE. See FIGURE 4(a)

• Route the LEG PRESS CABLE (3) around one 3-1/2” PULLEY (5) and re-assemble the PULLEY to the FLOA TING PULLEY PLA TES

usingthe BOL T , NUT and PULLEY which were removed. See FIGURE 4.

• Assemble one 3-1/2 PULLEY (5) to the PULLEY HOUSING (2) using one 3/8 X 1-3/4” BOL T (10) and one 3/8” LOCK NUT (12) as shown
in FIGURE 4(b). NOTE: CABLE MUST BE PLACED IN PULLEY HOUSING BEFORE INST ALLING PULLEY

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

7

6

12

11

10 3/8 X 1-3/4”

LEG PRESS BRACKET

4

5

7 3/8 X 4-3/4”

3

FIGURE 5

STEP 5:

• Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the

BRACKET (from 100 LEG PRESS kit) using one 3/8 X 1-3/4” BOL T (10), one 3/8” W ASHER (1 1), one “L” CABLE RET AINER (3)
and one 3/8” LOCK NUT (12) as shown in FIGURE 5. Make sure the CABLE is in the grooves of all the pulleys.

• SECURELY attach the BRACKET (from LP5 LEG PRESS) to the SEAT FRAME using two 3/8” X 4-3/4” BOLTS (7), two 3/8” W ASH-

ERS (11), and two 3/8” LOCK NUTS (12). See FIGURE 5.

12

4

3/8 X 1-3/4” 10

5

SEA T FRAME

FIGURE 6

STEP 6:

• Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the

bracket on the SEA T FRAME using one 3/8 X 1-3/4” BOLT (10) and one 3/8” LOCK NUT (12) as shown in FIGURE 6. Make sure the
CABLE is in the grooves of all the pulleys.

8

FIGURE 7

SEAT FRAME

3/8 LOCK NUT

STEP 7:

• Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the SEA T

FRAME using one 3/8 X 4-3/4” BOL T (7), two STEP SPACERS 1-9/16” (14) and one 3/8” LOCK NUT (12) as shown in FIGURE 7. Make
sure the CABLE is in the grooves of all the pulleys.

12

5

MAIN ARM

4

3/8 X 4-3/4” 10

14

12

5

4

13

3/8 X 2-3/4” 9

FIGURE 8

STEP 8:

• Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the

MAIN ARM using one 3/8 X 2-3/4” BOLT (9), two STEP SP ACERS 19/32” (13) and one 3/8” LOCK NUT (12) as shown in FIGURE

8. Make sure the CABLE is in the grooves of all the pulleys.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

9

6

FIGURE 9

SEAT FRAME

3/8” LOCK NUT

STEP 9:

• Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the

SEA T FRAME using one 3/8 X 4-3/4” BOL T (7), two STEP SP ACERS 1-9/16” (14), and one 3/8” LOCK NUT (12) as shown in
FIGURE 9. Make sure the CABLE is in the grooves of all the pulleys.

12

5

4

14

3/8 X 4-3/4” 7

FIGURE 10

MAIN ARM

12

5

4

13

3/8 X 2-3/4” 9

STEP 10:

• Carefully route the LEG PRESS CABLE (4) around one 3-1/2” PULLEY (5) and SECURELY assemble the 3-1/2” PULLEY (5) to the MAIN

ARM using one 3/8 X 2-3/4” BOL T (9), two STEP SP ACERS 19/32” (13) and one 3/8” LOCK NUT (12) as shown in FIGURE 10. Make
sure the CABLE is in the grooves of all the pulleys.

10

FIGURE 12

SEAT FRAME

4

12

15

3/8 X 4-3/4” 7

STEP 12:

• SECURELY assemble the swivel end of the LEG PRESS CABLE (4) to the SEA T FRAME using one 3/8 X 4-3/4” BOL T (15), two STEP
SP ACERS 1-11/16” (15) and one 3/8” LOCK NUT (12). (NOTE: SECUREL Y tighten, then back nut off 1/4 turn)

CABLE ROUTING DIAGRAM

11

ADJUST!

ADJUST!

FIGURE 13

STEP 13:

• Before setting the correct amount of tension in the cables, push the HEAD PLATE down, insert the WEIGHT SELECTOR PIN,
and perform several repetitions at the leg press station. This will relax the cable system and prevent the HEAD PLATE from
lifting up.

THIS CONCLUDES THE ASSEMBL Y OF THE GS4-LP5A LEG PRESS ADAPTER KIT

Thank you for purchasing the Parabody GS4-LP5A Leg Press Adapter Kit. If unsur e of proper use of equip­ment, call your local Parabody distributor or call the Parabody customer service department at [phone].

12