Life Fitness GS2 User Manual
GS2 GYM SYSTEM
USER’S GUIDE
WARNING:
Read and follow all directions
for each step to ensure proper
assembly of this product.
CLASS H
PART # 7657701
REV. A
Version: GS2-105
Revision: 11/06
TABLE OF CONTENTS
Safety Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Tools Required for Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Gym Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
General Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Warranty Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Product Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
IMPORTANT SAFELY INFORMATION
T
HERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT.
T
O MINIMIZE RISK, FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions on the use of this machine. Use only for
intended exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it appears damaged. DO NOT attempt to fix a
broken or jammed machine. Notify your authorized Life Fitness dealer and have repairs made by
an authorized service technician before use.
5. Be certain that the weight pin is inserted completely. Use only the pin provided by the
manufacturer. If unsure, call your authorized Life Fitness dealer.
6. Never pin the weights or prop plate into an elevated position. DO NOT use the machine if found
in this condition. DO NOT attempt to fix. Notify your authorized Life Fitness dealer.
7. Inspect cables and their connections before using machine. Pay particular attention to the cable
ends. DO NOT attempt to fix any problems. Notify your authorized Life Fitness dealer and have
repairs made by an authorized service technician before use.
8. Make sure all spring-loaded pull pins are fully engaged in the adjustment position and fully tighten
the thumbscrew before use.
9. Children must not be allowed near this machine. Supervise teenagers.
Note: In our continuing effort to improve our products, specifications are subject to change.
©2006 Life Fitness, a division of Brunswick Corporation. All rights reserved.
www.lifefitness.com
2
IMPORTANT NOTES
Thank you for purchasing the Life Fitness GS2 Gym System. Please read these instructions thoroughly and keep them for future reference.
This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
TOOLS
REQUIRED FOR ASSEMBLY
• Rubber mallet or hammer
• 3/4” wrench
• 9/16” wrench
• Ratchet with 3/4” and 9/16” sockets
• 5/32” Allen wrench
• Adjustable wrench
• Tape measure.
B
OLT LENGTH RULER
Note: Bolt length is measured from the underside of the head of the bolt.
3
BOLT LENGTH
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
6
1’
Minimum Required Usable Space
Length = 82 inches (208.5 cm) 6’ 10”
Width = 71 inches (180.5 cm) 5’11”
Height = 83 inches (211 cm) 6’ 11”
Dimensions Including LP5 Leg Press (optional)
Length = 82 inches (208.5 cm) 6’ 10”
Width = 108 inches (180.5 cm) 9’ 0”
4
1 Square = 1’ X 1’
2’
3’
4’
5’
1’ 2’ 3’
4’
5’
6’
7’
8’
9’
6’
7’
5
PARTS LIST
Note: Some of the parts listed may be pre-installed.
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
6
STEP 1:
• LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four
3/8 X 3-3/4” BOLTS (30) and four 3/8” LOCK NUTS (34). See FIGURE 1.
• LOOSELY assemble the FOOTPLATE (62) to the lower holes in the FRAME (1) using one
3/8 x 3” BOLT (29) and one 3/8 LOCKNUT (34)
• LOOSELY assemble the TOP of FRAME BRACE (64) to the FRAME (1) using two 3/8 x 4” BOLT
(63), two 3/8 WASHERS (36) and two 3/8 LOCKNUTS (34). Assemble BOTTOM of FRAME
BRACE (64) to FRAME (2) using one 3/8 x 3” BOLT (29), one 3/8 x 2-1/2” BOLT (28)
three 3/8 WASHERS (36) and one 3/8 LOCKNUT (34)
6
36
F
IGURE 1
3/8 x 4”
3/8 x 3-3/4”
3/8 x 3”
3/8 x 2-1/2”
3/8 x 3”
1
62
29
30
63
34
3
34
34
28
29
64
2
36
7
CHECK THAT THE HEADPLATE AND WEIGHT PLATES
ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3
FIGURE
2
F
IGURE 3
STEP 4:
• Insert two GUIDE RODS (16) into the BASE (2) as
shown on FIGURE 4. Note: If the GS2 SHROUD
OPTION was purchased, place the GUIDE RODS
(16) through the BOTTOM SHROUD BRACKET
(FOUND IN THE SHROUD KIT BOX) into the BASE
(2), as shown in FIGURE 4.
Note: Lubricate GUIDE RODS (16) with silicon or
teflon spray available at most hardware stores.
• Slide the following items in order down each GUIDE
ROD (16), one WEIGHT STACK SPACER (45), and
one WEIGHT STACK CUSHION (46)
• Using EXTREME CARE slide all fifteen WEIGHT
PLATES (22) down the GUIDE RODS (16) onto the
WEIGHT STACK CUSHIONS (46). Make sure that the
keyholes of the WEIGHT PLATES (22) are all facing
the right way.
• Slide the head plate assembly down GUIDE RODS
(16) onto the weight stack.
• Slide the following items in order down each GUIDE
ROD (16), one WEIGHT STACK SPACER (45), and
one WEIGHT STACK CUSHION (46)
STEP 5:
• Carefully slide the RIGHT (5) and LEFT (4) BOOM PLATES onto the GUIDE RODS (16 )as shown in FIGURE 5 and
loosely assembly BOOM PLATES (5), (4) to frame (1) using two 3/8 x 3-3/4” BOLTS (30) and two 3/8” LOCK NUT (34)
CAUTION MUST BE TAKEN NOT TO PULL GUIDE RODS (16) OUT OF BASE (2)
• Screw ADJUSTABLE GLIDE (53) approximately 1/2” into FRAME (1) and tighten jam nut securely as shown.
8
FIGURE 4
FIGURE 5
48
16
HEAD
PLATE
ASSY
46
30
3/8 X 3-3/4
53
5
45
4
GS2 SHROUD
BRACKET
OPTION ONLY
2
34
16
Loading...