Life Fitness GS1 User Manual

GS1 GYM SYSTEM

CLASS H
PART # 7597201
REV . A

USER’S GUIDE

1

WARNING:

Read and follow all directions
for each step to insure proper
assembly of this product.

V ersion: GS1-103
Revision: 07/30/03

j

TABLE OF CONTENTS

Safety Statement.............2

General Notes..................3

Tools Required................3

Gym Layout.....................4

Parts list..........................5

Assembly Instructions.....6-20

General Maintenance.......21

W arranty Statement..........22

Product Services..............23

Insert-Registration Card

IMPORTANT SAFETY INFORMATION

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF

EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!

1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.

2. Obtain a medical exam before beginning any
exercise program.

3. Keep body and clothing free of all moving objects.

4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or

ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.

6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.

7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.

8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.

5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.

9. Children must not be allowed near this machine.
Supervise teenagers.

.

NOTE: In a continual effort to improve our products, specifications are subject to change
2002 Life Fitness, a division of Brunswick Corporation. All rights reserved.

©

ParaBody is a trademark of Brunswick Corporation

www.parabody.com

2

IMPORTANT NOTES

Please note:

* Thank you for purchasing the ParaBody GS1 Gym System. Please read these
instructions thoroughly and keep them for future reference.

* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.

T ools Required for Assembly

* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 5/32” Allen wrench
* Adjustable wrench
* T ape measure

Bolt Length Ruler

NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT .

BOLT LENGTH

BOL T LENGTH RULER:

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

3

6

1’

2’

3’

4’

5’

1’ 2’ 3’

4’

5’

6’

7’

8’

9’

6’

7’

1 Square = 1’ X 1’

Minimum Required Usable Space

Length = 82 inches (208.5 cm) 6’ 10”
Width = 71 inches (180.5 cm) 5’11”
Height = 83 inches (211 cm) 6’ 11”

Dimensions Including LP5 Leg Press (optional)

Length = 82 inches (208.5 cm) 6’ 10”

Width = 108 inches (180.5 cm) 9’ 0”

4

PARTS LIST

KEY

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32

PART #

ACU04-1163

ACU04-1158

ACU02-1060
ACU04-1160
ACU04-1384
ACU04-1344
ACU04-1100
ACU04-1098
ACU04-1159
ACU04-1162
ACU04-1157
ACU02-1071
ACU07-0135
ACU01-1782

ACU6194601

ACU01-1783
ACU04-1099
ACU01-2009

ACU10-0204ASY

ACU13-0091-2
ACU13-0091-1

ACU7292501

ACU06-0024
ACU12-0041

ACU05-0193
ACUDA1E03813416NB
ACUDA1E03821216NB
ACUDA1E03830016NB
ACUDA1E03833416NB
ACUDA1E03883416NB
ACUDA1C01210413NB

DESCRIPTION

FRAME

BASE

BASE PLA TE

BOOM PLA TE LEFT

BOOM PLA TE RIGHT

FRAME BRACE

FOOT PLA TE

PRESS ARM

PRIMARY PIVOT

SEA T ADJUST
LEG PEDEST AL
PULLEY PLA TE

SEA T/BACK P AD

3/4 X 17” TUBE

4 X 7” ROLLER P AD

72-3/8” GUIDE ROD

LA T BAR

3/4 X 17-1/2” TUBE

HEAD PLA TE ASSY

LA T CABLE

LOW CABLE

WEIGHT PLA TE

3-1/2” PULLEY

ANKLE STRAP

CHAIN
3/8 X 1-3/4” BOL T
3/8 X 2-1/2” BOL T

3/8 X 3” BOL T
3/8 X 3-3/4” BOL T
3/8 X 8-3/4” BOL T

1/2 X 104mm BOL T

QTY

1
1
2
1
1
1
1
1
1
1
1
2
2
1
6
2
1
2
1
1

1
15
12

1

1

2

1

9
15

2

1

KEY

33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59

PART #

ACUDA1E01283413NB
ACUDB2E03811000B
ACUDB2E01208000B
ACUDC1250100020B

ACUDC126013020B

ACU04-1171
ACU06-0363
ACU05-0322
ACU08-0074
ACU08-0073
ACU08-0011
ACU05-0320
ACU04-1165
ACU06-0047

ACUDA1E03840016NB

ACU05-0212

ACU7308601

ACU11-0068
ACU11-0060
ACU06-0194
ACU05-0017
ACU05-0036
ACU06-0357
ACU05-0311

ACUDI1080080U

ACUDB2E01212000B

ACU04-0622

DESCRIPTION

1/2 X 8-3/4” BOL T

3/8” LOCK NUT

1/2” LOW HT LOCK NUT

3/8” FLA T WASHER

1/2” FLA T WASHER

3-1/2 CABLE GUARD

3/4” PLASTIC W ASHER

3/4 X 4” SHAFT

3/8 X 3/4” FLANGE SP ACER

3/8 X 1-1/16” FLANGE SP ACER

3/8 X 1” LG SP ACER

3/8 X 1-1/2” LG SP ACER

WEIGHT ST ACK SP ACER

WEIGHT ST ACK CUSHION

3/8 X 4” BOL T

SHAFT COLLAR
WEIGHT ST ACK LABEL
T -HANDLE SPRING PIN
WEIGHT SELECTOR PIN

ST AR KNOB 3/8
ADJUST ABLE GLIDE
ST ARLOCK COLLAR

RH CAP

1/2” RH CAP HOLDER WSHER

SNAP LINK

1/2” LOCK NUT

LOW ROW BAR

QTY

1

26

1

22

2
2
4
1
2
8
4
4
2
2
2
2
1
1
1
1
1
6
2
2
3
1
1

NOTE: SOME OF THE P AR TS LISTED MAY BE PRE-INSTALLED

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

5

6

36

3/8 X 4

3/8 X 3-3/4

29

7

30

47

2

1

34

3/8 X 2-1/228

29

3/8 X 3

6

3

34

34

FIGURE 1

STEP 1:

• LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30)
and four 3/8” LOCK NUTS (34). See FIGURE 1.

• LOOSELY assemble the FOOTPLATE (7) to the lower holes in the FRAME (1) using one 3/8 x 3” BOLT (29) and one
3/8 LOCKNUT (34)

• LOOSELY assemble the TOP of FRAME BRACE (6) to the FRAME (1) using two 3/8 x 4” BOLT (47), two 3/8 WASHERS
(36) and two 3/8 LOCKNUTS (34) Assemble BOTTOM of FRAME BRACE (6) to FRAME (2) using one 3/8 x 2-1/2” BOLT
(28), one 3/8 x 3 (29), three 3/8 WASHERS (36) and one 3/8 LOCKNUT (34)

6

FIGURE 2

• CHECK THA T THE HEADPLA TE AND WEIGHT PLATES ARE ASSEMBLED AS SHOWN IN FIGURES 2 & 3

FIGURE 3

7

STEP 4:

• Insert two GUIDE RODS (16) into the BASE (2) as
shown on FIGURE 4. (NOTE: If the GS1 SHROUD

OPTION was purchased, place the GUIDE RODS
(16) through the BOTTOM SHROUD BRACKET
(FOUND IN THE SHROUD KIT BOX) into the BASE
(2), as shown in FIGURE 4.

• (NOTE: Lubricate GUIDE RODS (16) with silicon
or teflon spray available at most hardware stores.)

• Slide the following items in order down each GUIDE
ROD (16), one WEIGHT STACK SPACER (45), and
one WEIGHT STACK CUSHION (46)

• Using EXTREME CARE slide all fifteen

WEIGHT PLATES (22) down the GUIDE RODS (16)
onto the WEIGHT ST ACK CUSHIONS (46). Make sure
that the keyholes of the WEIGHT PLATES (22) are all
facing the right way .

• Slide the head plate assembly down GUIDE RODS
(16) onto the weight stack.

• Slide one SHAFT COLLAR (48) down each
GUIDE ROD (16).

48

16

HEAD
PLATE
ASSY

46

30

3/8 X 3-3/4

53

FIGURE 5

STEP 5:

5

34

4

45

GS1 SHROUD
BRACKET
OPTION ONL Y

2

FIGURE 4

16

• Carefully slide the RIGHT (5) and LEFT (4) BOOM PLATES onto the GUIDE RODS (16 )as shown in FIGURE 5 and loosely

assembly BOOM PLATES (5), (4) to frame (1) using two 3/8 x 3-3/4” BOLTS (30) and two 3/8” LOCK NUT (34)
[CAUTION MUST BE TAKEN NOT TO PULL GUIDE RODS (16) OUT OF BASE (2)]

• Screw ADJUSTABLE GLIDE (53) approximately 1/2” into FRAME (1) and tighten jam nut securely as shown

8

9

3/8 X 3”
TIGHTEN

20lbs/ft

29

36

34

8

PUSH FORWARD AND HOLD

FIGURE 6

STEP 6:

• Place PRESS ARM (8) into PRIMARY PIVOT (9) and insert two 3/8 X 3” BOLTS (29), and two 3/8” FLAT WASHERS
(36). While Pushing the PRESS ARM (8) forward, securely tighten the two 3/8 x 3” BOLTS (29) to 20 LBS/FT of torque
using two 3/8” FLAT WASHERS (36) and two 3/8” LOCKNUTS (34)

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

9

6

1/2 X 8-3/4”

33

37

40

1

58

48

SECUREL Y
TIGHTEN

FIGURE 7

STEP 7:

• SECUREL Y TIGHTEN ALL FRAME CONNECTION BEFORE PROCEEDING T O NEXT STEP

• SECURELY TIGHTEN top of both SHAFT COLLARS (48) flush to bottom of both BOOM PLATES (4),(5)

• Insert 3/4 x 4” SHAFT (40) into both 3/4” FLANGE BEARINGS on FRAME (1)

• Assemble the PRIMARY PIVOT (9) of the PRESS ARM ASSEMBLY to the top of the FRAME (1) using 1/2 X 8-3/4” BOLT (33),
two 1/2” FLAT WASHERS (37) and 1/2” LOCK NUT (58).

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

10

6

10

36

13

36

29

3/8 X 3”

19

49

22

3/8 X 3”

29

52

1

50

FIGURE 8

STEP 8:

• Apply WEIGHT STACK LABELS (49) to WEIGHTS (22) and HEAD PLATE (19) as shown in FIGURE 8.
Begin with number one at the HEAD PLATE (19) with larger numbers in consecutive order towards bottom of weight stack.

• Securely assemble one SEAT PAD (13) to the SEAT ADJUSTMENT (10) using two 3/8 X 3” BOLTS (29) and two
3/8” WASHERS (36) as shown.

• Securely assemble one SEAT PAD (13) to the FRAME (1) using two 3/8 X 3” BOLTS (29) and two 3/8” WASHERS (36)

as shown. The top connection of the FRAME BRACE (6) may have to be loosened and then re-tighten after SEAT PAD

(13) is tighten.

• Gently insert SEAT ADJUSTMENT (10) into tube located on FRAME (1)

• Securely tighten the SPRING PIN (50) to the FRAME (1) and hand tighten the STAR KNOB (52)

11

55

1/2 X 104mm

32

56

1

11

35

FIGURE 9

STEP 9:

• Assemble the LEG PEDEST A L (11) to the FRAME (1) using one 1/2 X 104mm BOLT (32), two RH W ASHERS (56)
and one 1/2” LOW HT LOCK NUT (35)

• Assemble two RH CAPS (55) to the 1/2” RH WASHERS (56) as shown in FIGURE 9

21

STEP 10:

• Route LAT CABLE (20) and LOW CABLE (21) as shown in FIGURE 10

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

12

20

FIGURE 10

6

ILLUSTRA TION A

• ILLUSTRATION “A” used as cable routing reference for steps 12-15

NOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER TO THE

CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEG
PRESS KIT

13

3/8 X 3-3/4”

30

42

31

3/8 X 8-3/4”

FIGURE 11

36

44

24

1

34

9

STEP 11:

• Refer to cable ILLUSTRATION “A” on page 13 for cable routing while installing pulleys.

• Assemble two 3-1/2” PULLEYS (24) into FRAME (1) using two 3/8 X 3-3/4” BOLTS (30), four 3/8 X 1-1/16”
FLANGE SPACERS (42) and two 3/8” LOCK NUTS (34) and tighten securely.

• Assemble one 3-1/2” PULLEY (24) into PRIMARY PIVOT (9) upper hole using one 3/8 X 8-3/4” BOLT (31),
two 3/8” FLAT WASHERS (36), two 3/8 X 1-1/2” SPACERS (44) and one 3/8” LOCK NUT (34) and tighten securely

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

14

6

3/8 X 3-3/4”

30

38

24

31

44

3/8 X 8-3/4”

36

42

9

27

3/8 X 1-3/4”

1

43

34

FIGURE 12

STEP 12:

• Refer to cable ILLUSTRATION “A” on page 13 for cable routing while installing pulleys.

• Assemble one 3-1/2” PULLEY (24) into the PRIMARY PIVOT (9) lower hole using one 3/8 X 8-3/4” BOLT (31),
two 3/8” FLAT WASHERS (36), two 3/8 X 1-1/2” SPACERS (44) and one 3/8” LOCK NUT (34) and tighten securely.

• Assemble one 3-1/2” PULLEY (24) to the FRAME (1) using one 3/8 X 3-3/4” BOLT (30), two 3/8 X 1-1/16”
FLANGE SPACERS (42), one 3/8” LOCK NUT (34) and tighten securely

• Loosely assemble one 3-1/2” PULLEY (24) between PULLEY PLATES (12) using one 3/8 X 1-3/4” BOLT (27) and
one 3/8” LOCK NUT (34).

• Assemble two 3-1/2” PULLEYS (24) between the left and right BOOM PLATES (4) and (5) using two 3/8 X 3-3/4” BOLTS (30),
two 3/8 X 1” SPACERS (43), two 3-1/2” CABLE GUARDS (38) and two 3/8” LOCK NUTS (34)

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

12

345

6

15

FIGURE 13

35

20

SECURELY
TIGHTEN
JAM NUT

1/2 1/2 1/2 1/2

0

51

1

2

34

WEIGHT
ST ACK
SHAFT

STEP 13:

• Slip ring of WEIGHT SELECTOR PIN (51) down WEIGHT STACK SHAFT and insert pin into one of the weights

• Screw end of LAT CABLE (20) into top of PLATE SHAFT (18) and securely tighten JAM NUT as shown in FIGURE 13

• Securely tighten 1/2” LOCK NUT (35) on PRIMARY PIVOT of PRESS ARM (9).

16

11

3/8 x 3”

3/8 x 3-3/4”

30

24

FIGURE 14

29

1

41

34

42

34

36

21

STEP 14:

• Refer to cable ILLUSTRATION “A” on page 13 for cable routing while installing pulleys.

• [CABLE MUST BE POSITIONED BETWEEN PULLEY AND LOWER BOLT ASSEMBLY ON
LEG PEDESTAL (11) AND FRAME (1)]

• Securely assemble the ball end of the LOW CABLE (21) and one 3-1/2” PULLEY (24) to the LEG PEDESTAL (11) using two
3/8 X 3-3/4” BOLTS (30), two 3/8” X 1-1/16” FLANGE SPACERS (42), two 3/8” WASHERS (36), and two 3/8” LOCKNUTS

(34). (NOTE: The LEG CABLE (21) should be routed over the retaining bolt as shown in FIGURE 14.)

• Securely assemble one 3-1/2” PULLEY (24) and two 3/8 X 3/4 FLANGE SPACERS (41) to the FRAME (1) using one

3/8 X ” BOLTS (29), and one 3/8” LOCKNUT (34). (NOTE: The LEG CABLE (21) should be routed over the retaining

bolt as shown in FIGURE 14.)

17

12

3/8 X 1 -3/4”

3/8 X 3-3/4”

FIGURE 15

30

27

3

36

34

43

24

STEP 15:

• Refer to cable ILLUSTRATION “A” on page 13 for cable routing while installing pulleys.

• Assemble one 3-1/2” PULLEY (24) between BASE PLATES (3) using one 3/8 X 3-3/4” BOLT (30), two 3/8 X 1” SPACERS
(43), one 3/8” LOCK NUT (34) and tighten securely.

• Loosely assemble one 3-1/2” PULLEY (24) between the PULLEY PLATES (12) using one 3/8 X 1-3/4” BOLT (27), and one

3/8” LOCK NUT (34).

• Secure end of LOW CABLE (21) using one 3/8 x 3-3/4” BOLT (30), one 3/8” FLAT WASHER (36) and one 3/8” LOCK NUT (34)

as shown in FIGURE 15

• Tighten both 3-1/2” PULLEYS (24) located on PULLEY PLATES (12)

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

18

6

18

1

54

39

10

11

15

14

FIGURE 16

STEP 16:

• Attach two 4 X 7” ROLLER PADS (15) to the LEG PEDESTAL (11) using one 3/4 X 17” TUBE (14) and two

3/4” STARLOCK COLLARS (54) as shown in FIGURE 16.

• Attach two 4 X 7” ROLLER PADS (15) to the SEAT ADJUST (10) using one 3/4 X 17-1/2” TUBE (18), two PLASTIC

WASHERS (39) and two 3/4” STARLOCK COLLARS (54) as shown in FIGURE 16.

• Attach two 4 X 7” ROLLER PADS (15) to the FRAME (1) using one 3/4 X 17-1/2” TUBE (18),

two PLASTIC WASHERS (39) and two 3/4” STARLOCK COLLARS (54) as shown in FIGURE 16.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

19

6

17

ADJUSTMENT

53

ADJUSTMENT

TIGHTEN

19

JAM NUT
SECURELY

26

25

59

57

51

FIGURE 17

STEP 17:

• If upon completion of assembly, the HEAD PLATE (19) does not sit on top of the first WEIGHT PLATE (22), push the

HEAD PLATE (19) down, insert the WEIGHT SELECTOR PIN (51) and perform several repetitions at the press station.
This will relax the cable system and prevent the HEAD PLATE (19) from lifting up. See FIGURE 17

• If after completing previous step, the HEAD PLATE (19) still does not sit on top of the first WEIGHT PLATE (22) or if

there is excess slack in the cable system, adjust the threaded end of the LAT CABLE (20) and ADJUSTABLE GLIDE (53)
accordingly and retighten the jam nuts. See figure 17

• For maximum performance, the HEAD PLATE (19) should just barely sit on the top WEIGHT PLATE (22)

• Attach the LAT BAR (17) to the ball end of LAT CABLE (20) using one SNAP LINK (57) as shown in FIGURE 17.

• Attach the ANKLE STRAP (25) to the 12 LINK CHAIN (26) using two SNAP LINKS (57) as shown in FIGURE 17

Thank you for purchasing the ParaBody GS1 Gym System. If unsure of proper use of equipment, call
your local ParaBody distributor or call the ParaBody customer service department at [phone]

20

MAINTENANCE

Please note:

* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at [phone].

* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury

* Lubricate guide rods with a teflon based (or equivalent) lubricant on a regular basis

* PLEASE RECORD THE INFORMATION REQUESTED BELOW . IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.

SERIAL NUMBER LOCATED ON
PULLEY BRACKET

MODEL #________________________

SERIAL #_________________________

DATE OF PURCHASE: _____________

DEALERS NAME: _________________

DEALERS PHONE #_______________

SERIAL NUMBER LOCATION

Thank you for pur chasing the ParaBody GS1 Gym System.

21

LIMITED WARRANTY

ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONL Y.

1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.

2. LIMITED WARRANTY ON P ARTS. If the following part s are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger , spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.

3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.

4. CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty .

5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning part s to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.

6. SHIPPING . If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.

7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.

8. OWNER’S RIGHT . This Limited W arranty gives you specific legal rights. Y ou may also have other rights, which vary depending on local law .

9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty .
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.

10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury , loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.

NOTES:

22

LIFE FITNESS CONSUMER DIVISION

14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.

T el: 763.323.4500 Fax: [phone]

800.328.9714 (T oll-free within the U.S. and Canada)
www.parabody.com

INTERNATIONAL OFFICES

Life Fitness Atlantic BV
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: [phone]
Fax: [phone]

Life Fitness EUROPE GmbH
Siemensstrasse 3
85716 Unterschleissheim
Germany
Phone: [phone]
Fax: [phone]

Life Fitness Italia S.R.L.
V ia Elvas 92
39042 Bressanone
Italy
Phone: [phone]
Fax: [phone]

Life Fitness (UK) Ltd.
Queen Adelaide
Ely , Cambs CB7 4UB
United Kingdom
Phone CSS: [phone]
Fax CSS: [phone]

Life Fitness Benelux N.V.
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: [phone]
Fax: [phone]

Life Fitness Japan
8/F , Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, T okyo 151-0051
Japan
Phone: [phone]
Fax: [phone]

Life Fitness Asia Pacific Limited
Room 2610, Miramar T ower
132 Nathan Road, T simshatsui
Kowloon, Hong Kong
Phone: [phone]
Fax: [phone]

23

Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2

º andar (Confab)

3
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Brazil
Phone: [phone]
Fax: [phone]