Congratulations on your purchase of this wine cooler. In buying this product, which is
distinguished by its perfect user-friendliness, impeccable reliability and high quality, you
have chosen a top class appliance. We wish you a lot of pleasure with your new wine
cooler – and a lot of enjoyment from your wines.
The fewer the grapes produced in an area, the
better the wine.
Poor, well-drained soils are best for good wines. The properties of the soil influence the
vitality of the vine, which in turn affects the quality of the grape. Climate is another
factor that is important for wine. Because light and air humidity are important for the
development of the flavour of the wine.
The right environment for your wines.
A vine is an extremely sensitive plant. From the time it is planted to its maturing period
and the time the grapes are harvested and the wine is made, it is dependent on three factors: light, air humidity and ambient temperature. This sensitivity continues even once
the wine is bottled. To allow the flavour of the wine to fully develop or to preserve the
excellent aroma, the wine has to be stored perfectly – and your wine cooler offers the
best conditions for this.
16
GB
Contents Page
Setting up ............................................................................................................................ 18
• Avoid locating it in direct sunlight or near heat sources such as an oven or a radiator.
• The floor should be level and even. You can compensate for an uneven floor by adjusting the adjustable feet.
• Please make sure the appliance is properly ventilated.
• Standard EN 378 specifies that the room in which you install your appliance must
have a volume of 1 m3 per 8 g of R 600a refrigerant used in the appliance, so as to
avoid the formation of inflammable gas/air mixtures in the room where the appliance
is located in the event of a leak in the refrigerant circuit. The quantity of refrigerant
used in your appliance is indicated on the type plate on the inside of the appliance.
• The appliance is set to operate within specific ambient temperature limits according
to its climate rating. These temperature limits should not be exceeded. The correct
climate rating for your appliance is indicated on the type plate.
SN - ST = +10°C to +38°C
SN - T = +8°C to +43°C
Dimensions
WT 4177: height: 1658 mm, width: 660 mm, depth: 671 mm
Electrical requirement
Power supply (AC) and voltage at the operating point must comply with the details on
the type plate. The type plate is located on the top left-hand side on the inside of the
appliance. The socket must be fused with a 10 A fuse or higher, it must be away from
the rear of the appliance and must be easily accessible.
Operating and control elements
Lower compartment temperature display
Upper compartment temperature display
Lower compartment temperature setting buttons
Upper compartment temperature setting buttons
Audible warning on/off button
You are recommended to clean the appliance before switching it on for the first time
(see Cleaning). Connect the appliance to the mains - the appliance is switched on.
• To switch the appliance off:
so that the temperature display goes out.
• To switch the appliance on:
lights up.
Keep the ON / OFF button pressed for 3 sec.
Press the ON / OFF button until the Display
Cooling wine
The wine cooler enables you to bring your wines gradually
and evenly to the right temperature for drinking in 6 different temperature zones.The table on the left indicates the
temperature settings in each compartment, which are preset in the factory. The appliance is delivered with the grid
shelves in the right positions to achieve these temperatures.
The specified temperatures are guide values. Depending on
the number of bottles in the appliance, the ambient temperature and the position in the various compartments, the temperatures may differ.
Setting the temperature
The temperature may be adjusted slightly in the
top and bottom storage compartment.
+16°C to +18°C.
Top:
Bottom: +5°C to +7°C.
The temperatures in the central zones will thus change accordingly.
To reduce the temperature:
To increase the temperature: Press the button UP ▲
- While you are entering the temperature, the set temperature will flash on the display.
- You can change the settings in increments of 1°C briefly pressing the button again.
- The electronic controls will switch over automatically about 5 seconds after the
last time you pressed the button, and the actual temperature will be displayed.
Press the button DOWN▼
19
Loading...
+ 10 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.