Liebherr SKBS4210, SKES4210RH, SKES4210LH, SGNEF3036RHSKES4210L, SKBS4210SGNBS3010 Installation and Operation Guide
...
Operating and installation instructions
Upright refrigerator
281013
SKes/Sk/K/Kes 36...42 ... 6
7085582 - 01
Appliance at a glance
Contents
1 Appliance at a glance............................................ 2
1.1 Description of appliance and equipment.................. 2
1.2 Range of appliance use............................................ 2
1.3 Conformity................................................................ 3
1.4 External dimensions of the appliance....................... 3
1.5 Saving energy.......................................................... 3
1.6 HomeDialog............................................................. 4
2 General safety information................................... 4
3 Controls and displays........................................... 5
3.1 Operating and control elements............................... 5
3.2 Temperature display................................................. 5
4 Putting into operation............................................ 5
4.1 Transporting the appliance....................................... 5
4.2 Installing the appliance............................................. 5
4.3 Changing over the door hinges................................ 6
4.4 Insertion into a row of kitchen units........................... 8
4.5 Disposing of packaging............................................ 8
4.6 Connecting the appliance......................................... 8
4.7 Switching on the appliance....................................... 8
5 Control.................................................................... 8
5.1 Brightness of the temperature display...................... 8
5.2 Child proofing........................................................... 9
5.3 Door alarm................................................................ 9
5.4 Food refrigeration..................................................... 9
5.5 Setting the temperature............................................ 9
5.6 SuperCool................................................................ 9
5.7 Fan........................................................................... 10
5.8 Shelves.................................................................... 10
5.9 Using the sectioned shelf......................................... 10
5.10 Door racks................................................................ 10
5.11 Removing the bottle holder....................................... 10
5.12 Vegetable bins......................................................... 11
6 Maintenance........................................................... 11
6.1 Cleaning the appliance............................................. 11
6.2 Customer service..................................................... 11
7 Malfunction............................................................. 12
8 Decommissioning.................................................. 12
8.1 Switching off the appliance....................................... 12
8.2 Taking the appliance out of service.......................... 12
9 Disposing of the appliance................................... 13
1 Appliance at a glance
1.1 Description of appliance and equipment
Fig. 1
(1) Operating panel (9) Bottle shelf
(2) Ceiling light (10) Defrost water channel
(3) Fan (11) Glass shelf
(4) Box shelves, removable (12) Type plate
(5) Glass shelves, relocat-
able
(6) Door rack for tinned
food, relocatable
(7) Glass shelf, sectioned,
relocatable
(8) Door rack for bottles,
relocatable
(13) Coldest zone
(14) Vegetable compartment
(15) Height-adjustable foot *
1.2 Range of appliance use
Note
Place food inside the appliance as shown in the diagram.
u
This allows the appliance to save energy during operation.
Shelves, drawers and baskets are arranged for optimum
u
energy efficiency on delivery.
The appliance is suitable solely for cooling food
in a domestic environment or similar. This
includes use in, for example
-
in staff kitchenettes, bed and breakfast establishments,
-
by guests in country homes, hotels, motels
and other forms of accommodation,
-
in catering and similar services in the wholesale trade
Use the appliance solely as is customary within
a domestic environment. All other types of use
are inadmissible. The appliance is not suitable
for storing and cooling medicines, blood
plasma, laboratory preparations or similar
2 * Depending on model and options
Appliance at a glance
substances and products covered by the
2007/47/EC Medical Devices Directive. Misuse
of the appliance can result in the stored products suffering harm or perishing. Furthermore,
the appliance is not suitable for operation in
potentially explosive atmospheres.
The appliance is set to operate within specific
ambient temperature limits according to its
climate rating. The correct climate rating for
your appliance is indicated on the type plate.
Note
Compliance with the ambient temperatures
u
indicated is required, otherwise the cooling
performance is reduced.
Climate
rating
SN 10 °C to 32 °C
N 16 °C to 32 °C
ST 16 °C to 38 °C
T 16 °C to 43 °C
for ambient temperatures of
1.4 External dimensions of the appliance
1.3 Conformity
The refrigerant circuit is tested for leakage. The appliance
complies with the relevant safety regulations and EC Directives
2006/95/EC, 2004/108/EC, 2009/125/EC and 2010/30/EU.
Note for test institutions:
Tests are to be carried out according to the applicable
standards and guidelines.
Preparation and testing of the appliances must be carried
out taking the manufacturer's loading plans and the
notes in the operating manual into account.
Fig. 2
Designation H (mm)
K(es) 36.., SK(es) 36.. 1655
K(es) 42.., SK(es) 42.. 1852
x
For appliances supplied with wall spacers, the measurement
increases by 35 mm (see 4.2) .
1.5 Saving energy
Always ensure good ventilation. Do not cover ventilation
-
openings or grille.
Always keep fan louvres clear.
-
Do not place appliance in areas of direct sunlight or next to a
-
stove, heater or similar object.
The energy consumption depends on the installation condi-
-
tions, e.g. the ambient temperature (see 1.2) .
Keep the time the appliance is open to a minimum.
-
The lower the temperature setting, the higher the power
-
consumption.
Store food logically. (see Appliance at a glance).
-
Ensure that all food is well packed and covered for storage.
-
This will prevent frost from forming.
Remove food as needed in order that it does not warm too
-
much.
First cool warm food to room temperature before storing it .
-
Accumulated dust increases the energy
consumption:
Once a year, dust the refrigerating unit
-
together with the metal grille of the heat
exchanger at the back of the appliance.
* Depending on model and options 3
General safety information
1.6 HomeDialog
Depending on model and options, the HomeDialog system can be used to network a number
of Liebherr appliances (situated, for example, in
the basement) with a main appliance (sited, for
example, in the kitchen) and control them via the
latter. You will find more information on the
benefits, requirements and principle of operation
on the internet at www. liebherr.com.
2 General safety information
Danger for the user:
-
This appliance can be used by children of 8
years old and over, and also by persons with
restricted physical, sensory or mental
capacity or lack of experience and knowledge, if they are supervised or have been
instructed on safe use of the appliance and
understand the resulting risks. Children must
not be allowed to play with the appliance.
Cleaning and user maintenance must not be
carried out by children without supervision.
-
When disconnecting the appliance from the
supply, always take hold of the plug. Do not
pull the cable.
-
In the event of a fault pull out the mains plug
or deactivate the fuse.
-
Do not damage the mains power cable. Do
not operate the appliance with a defective
mains power cable.
-
Have any repairs to or intervention in the
appliance, and any change of the mains
power cable, carried out by the customer
service only or by other specialised personnel
trained for the purpose.
-
Only assemble, connect and dispose of the
appliance according to the instructions.
-
Please keep these instructions in a safe place
and pass them on to any subsequent owners.
-
Special-purpose lamps (incandescent lamps,
LEDs, fluorescent tubes) in the appliance
serve to illuminate the appliance interior and
are not suited for room illumination.
Fire hazard:
-
The refrigerant R 600a is environmentally
friendly but flammable. Escaping refrigerant
may ignite.
•
Do not damage the refrigerant circuit pipes.
•
Do not allow naked flames or ignition
sources to enter the appliance.
•
Do not use any electrical appliances in the
interior (e.g. steam cleaners, heaters, ice
cream maker etc.).
•
If refrigerant escapes: remove any naked
flames or sources of ignition from the
leakage area. Ventilate the room well.
Notify the after-sales service.
-
Do not store explosives or sprays using
combustible propellants such as butane,
propane, pentane, etc. in the appliance. To
identify these spray cans, look for the list of
contents printed on the can, or a flame
symbol. Gases possibly escaping may ignite
due to electrical components.
-
Keep burning candles, lamps and other items
with naked flames away from the appliance
so that they do not set the appliance on fire.
-
Please be sure to store alcoholic drinks or
other packaging containing alcohol in tightly
closed containers. Any alcohol that leaks out
may be ignited by electrical components.
Danger of tipping and falling:
-
Do not misuse the plinth, drawers, doors etc.
as a step or for support. This applies particularly to children.
Danger of food poisoning:
-
Do not consume food which has been stored
too long.
Danger of frostbite, numbness and pain:
-
Avoid lasting skin contact with cold surfaces
or refrigerated/frozen food or take protective
steps, e.g. wear gloves. Do not consume ice
cream, water ice or ice cubes immediately
and do not consume them too cold.
Danger of injury and damage:
-
Hot steam can lead to injury. Do not use electrical heating or steam cleaning equipment,
open flames or defrosting sprays to defrost.
-
Do not use sharp implements to remove the
ice.
Please observe the specific information in
the other sections:
DANGER identifies a situation involving direct
danger which, if not obviated, may
result in death or severe bodily
injury.
WARNING identifies a dangerous situation
which, if not obviated, may result in
death or severe bodily injury.
CAUTION identifies a dangerous situation
which, if not obviated, may result in
minor or medium bodily injury.
NOTICE identifies a dangerous situation
which, if not obviated, may result in
damage to property.
Note identifies useful information and tips.
4 * Depending on model and options
3 Controls and displays
3.1 Operating and control elements
Controls and displays
Fire hazard due to refrigerant!
The refrigerant R 600a is environmentally friendly but flammable. Escaping refrigerant may ignite.
u
WARNING
Do not damage the piping of the refrigeration circuit.
Fig. 3
(1) Alarm button (8) Fan button
(2) SuperCool button (9) Temperature display
(3) On/Off button (10)Fan symbol
(4) Alarm symbol (11) Child-proofing symbol
(5) Menu symbol (12) SuperCool symbol
(6) Down setting button (13) HomeDialog symbol
(7) Up setting button
3.2 Temperature display
The following are displayed in normal operation:
the average cooling temperature
-
The following displays indicate malfunction. Possible causes
and corrective action (see Malfunction).
-
F0 to F9
4 Putting into operation
4.1 Transporting the appliance
CAUTION
Risk of injury and danger of damage as a result of incorrect
transport!
Transport the appliance in a packed condition.
u
Transport the appliance upright.
u
Do not transport the appliance without assistance.
u
4.2 Installing the appliance
WARNING
Fire hazard due to dampness!
If live parts or the mains lead become damp this may cause
short circuits.
The appliance is designed for use in enclosed areas. Do not
u
operate the appliance outdoors or in areas where it is
exposed to splash water or damp conditions.
Risk of fire due to short circuit!
If the mains cable/connector of the appliance or of another
appliance touch the rear of the appliance, the mains cable/
connector may be damaged by the appliance vibrations,
leading to a short circuit.
u
u
WARNING
Stand the appliance so that it is not touched by connectors
or main cables.
Do not plug the appliance or any others into sockets located
near the rear of the appliance.
Fire hazard and danger of damage!
u
Blocked ventilation openings pose a risk of fire and damage!
u
NOTICE
Risk of damage due to condensate!
If your appliance is not a Side-by-Side (SBS) appliance:
u
q
q
q
q
q
q
q
u
u
NOTICE*
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accompanying care product.
Otherwise the surface coating will be affected.
u
u
u
u
u
The spacers supplied with some appliances must be used to
achieve the stated energy consumption. These will extend the
depth of the appliance by approx. 35 mm. The appliance is fully
functional if the spacers are not used, but does have a slightly
higher energy consumption.
WARNING
Do not place appliances emitting heat e.g. microwaves,
toasters etc. on the appliance!
WARNING
Always keep the ventilation openings clear. Always ensure
that the appliance is properly ventilated!
do not install the appliance directly alongside a further refrigerator/freezer.
In the event that the appliance is damaged, contact the
supplier immediately before connecting to the mains.
The floor at the site must be flat and level.
Do not install the appliance in a location where it is exposed
to direct radiation of the sun, next to a cooker, heater and
similar.
Always stand the appliance backed directly to the wall using
the enclosed wall spacers (see below).
The appliance may be moved only when it is empty.
Do not install the appliance without assistance.
Standard EN 378 specifies that the room in which you install
your appliance must have a volume of 1 m2 per 8 g of R
600a refrigerant used in the appliance. If the room in which
the appliance is installed is too small, a flammable gas-air
mixture may form in the event of a leakage in the refrigeration circuit. The quantity of refrigerant used in your appliance
is indicated on the type plate on the inside of the appliance.
Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because otherwise there will be vibratory noise!
Remove the protective film from the outside of the appliance.*
Wipe the coated door surfaces using a soft, clean cloth
only.
Apply a stainless steel cleaner only to the stainless steel
side walls evenly, wiping with the grain. Subsequent
cleaning becomes easier as a result.
Wipe side walls with a paint finish using a soft, clean
cloth only.
Remove the protective film from the decorative trims.*
Remove all transit supports.
* Depending on model and options 5
Putting into operation
In the case of an appliance with
u
enclosed wall spacers, mount the
wall spacers on the back of the
appliance at the top left and right.
Dispose of packaging material (see 4.5) .
u
Align the appliance so that it
u
stands firmly and on a level by
applying the accompanying
spanner to the adjustableheight feet (A) and using a
spirit level.
Then support the door: Extend
u
the adjustable foot at the turn
hinge (B) until it rests on the
floor and then make a further
90° turn.
When a Side-by-Side appliance (S…) is fitted together with
a second appliance (as a SBS combination):
Proceed according to the Side-by-Side combined fridge-
u
freezer installation instructions. (Accessories bag of the SBS
freezer/appliance with freezer compartment)
Fig. 4
Close the door.
u
Pull off the cover
u
Lift off the cover
u
Risk of injury if the door tips!
u
u
u
CAUTION
Take good hold of the door.
Set down the door carefully.
Unscrew the upper turn hinge
Fig. 4 (13)
Lift off the door and set it aside.
u
Fig. 4 (10)
Fig. 4 (11)
and lift it off.
forwards and upwards.
.
Fig. 4 (12)
(2x Torx® 25)
Note
Clean the appliance (see 6.1) .
u
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
Always see to good ventilation at the installation site.
u
4.3 Changing over the door hinges
You can change over the door hinges if necessary.
NOTICE
Risk of damage to side-by-side appliances due to condensation!
When a side-by-side appliance (S…) is fitted together with a
second appliance (as a SBS combination), the door hinges
must remain as delivered.
Do not change over the door hinges.
u
Ensure that the following tools are to hand:
Torx® 25
q
Torx® 15
q
Screwdriver
q
Battery-powered screwdriver, if necessary
q
Second person for fitting work, if needed
q
Accompanying Allen key size 2*
q
4.3.1 Detaching the door
4.3.2 Distinguishing between bearing elements
Some appliances are height-adjustable, as can be noted from
the bearing pin in the lower turn hinge:
For appliances without
u
height adjustment,
continue with item
(see 4.3.3) .
For appliances with
u
height adjustment,
continue with item
(see 4.3.4) .
4.3.3 Changing the bearing parts
for appliances without height adjustment
Note
Remove any food from the door racks before removing the
u
door, so that no food falls out.
6 * Depending on model and options
Putting into operation
Lift out the bearing pin
u
Fig. 5 (23)
Lift off the stopper
u
Unscrew
u
Unscrew
u
it to the opposite location hole of the turn hinge and screw it
firmly into place.
Carefully lift off the cover on the handle side
u
transfer it to the opposite side.
Screw the turn hinge
u
hinge side, possibly using a cordless screwdriver (with
4 Nm).
Re-insert the stopper
u
Re-insert the bearing pin
u
washer and adjustable-height foot. In so doing, pay attention
that the locating lug points backwards
and adjustable-height foot
Fig. 5 (26)
Fig. 5 (29)
Fig. 5 (22)
Fig. 5 (21)
the turn hinge
the bearing element
Fig. 5 (25)
Fig. 5 (21)
.
Fig. 5 (25)
firmly into place on the new
into the other hole.
Fig. 5 (22)
together with washer
Fig. 5 (24)
.
.
Fig. 5 (28)
, transfer
Fig. 5 (27)
together with the
Fig. 5
and
Unscrew
u
to the opposite location hole of the turn hinge and screw it
firmly into place.
Re-insert the stopper
u
Carefully lift off the cover on the handle side
u
transfer it to the opposite side.
Screw the turn hinge
u
hinge side, possibly using a cordless screwdriver (with
4 Nm).
Re-insert the bearing pin
u
washer and adjustable-height foot.
Tighten the threaded pin
u
Fig. 6 (29)
the bearing element
Fig. 6 (21)
Fig. 6 (25)
into the other hole.
firmly into place on the new
Fig. 6 (22)
Fig. 6 (40)
.
Fig. 6 (28)
transfer it
Fig. 6 (27)
together with the
4.3.5 Transferring the handle
Transfer the spring clamp
u
Fig. 7 (31)
latch nose and pull the
spring clamp off over it.
Slide the spring clamp
u
into place on the new
hinge side until it clicks
into place.
: Depress the
and
Fig. 7
4.3.4 Changing the bearing parts
For appliances with height adjustment
Using the accompanying Allen key, unscrew the threaded
u
pin
Fig. 6 (40)
Turn and lift out the bearing pin
u
washer
Lift out the stopper
u
Unscrew
u
Fully unscrew the threaded pin
u
the opposite side, at the turn hinge, until it is flush outside
with the turn hinge.
by about 1 turn.
Fig. 6 (23)
Fig. 6 (26)
Fig. 6 (22)
and adjustable-height foot
Fig. 6 (21)
the turn hinge
.
Fig. 6 (25)
Fig. 6 (40)
and screw it in on
together with the
Fig. 6 (24)
.
Fig. 6
.
Fig. 8
Lift the stopper
u
transfer it.
Dismantle the door handle
u
and pressure plates*
side.
When fitting the pressure plates on the opposite side, make
u
sure they snap properly into place.*
Fig. 8 (33)
Fig. 8 (34)
out of the door bearing bush and
Fig. 8 (32)
, stoppers
and transfer to the opposite
Fig. 8 (33)
4.3.6 Fitting the door
Place the door from above onto the lower bearing pin
u
Fig. 6 (22)
Close the door.
u
Insert the upper turn hinge
u
hinge side.
Screw the upper turn hinge
u
4 Nm)(2x Torx® 25)
holes with a bradawl or use a cordless screwdriver.
Snap the cover
u
the opposite side.
.
Fig. 4 (13)
Fig. 4 (10)
Fig. 4 (12)
Fig. 4 (12)
and cover
in the door on the new
firmly into place (with
. Possibly make preliminary
Fig. 4 (11)
into place at
4.3.7 Aligning the door
Align the door to the appliance housing by way of the two
u
oblong holes in the bottom turn hinge
unscrew the middle screw.
Fig. 6 (25)
. To do so,
* Depending on model and options 7
Control
Risk of injury due to the door dropping out!
If the bearing parts are not screwed into place firmly enough,
the door may drop out. This may lead to severe injuries. What
is more, the door may not close and therefore the appliance
may fail to cool properly.
u
u
4.4 Insertion into a row of kitchen units
WARNING
Screw the turn hinges firmly into place with 4 Nm.
Check all of the screws and retighten if necessary.
4.5 Disposing of packaging
Danger of suffocation due to packing material and plastic film!
u
The packaging is made of recyclable materials:
-
-
-
-
-
u
WARNING
Do not allow children to play with packing material.
corrugated board/cardboard
expanded polystyrene parts
polythene bags and sheets
polypropylene straps
nailed wooden frame with polyethylene panel*
Take the packaging material to an official collecting point.
4.6 Connecting the appliance
NOTICE
Risk of damage to the electronic control system!
Do not use stand-alone inverters (conversion of d.c. to a.c./
u
three-phase) or energy saving plugs.
Fig. 9
(1) Stack cabinet (3) Kitchen cabinet
(2) Appliance (4) Wall
x
For appliances supplied with wall spacers, the measurement
increases by 35 mm (see 4.2) .
The appliance can be inserted into a row of kitchen units. To
match the appliance
a suitable stack cabinet
ance.
When installing with kitchen units (max. depth 580 mm), the
appliance can be positioned directly next to the kitchen cabinet
Fig. 9 (3)
50 mmx in the centre of the appliance in relation to the kitchen
cabinet front.
Important for the ventilation:
-
-
-
If the appliance is installed with the hinges next to a wall
Fig. 9 (4)
least 40 mm. This corresponds to the projection of the handle
when the door is open.
. The appliance will project by 34 mmx at the sides and
At the back of the stack cabinet there has to be a ventilation
duct of at least 50 mm depth throughout the width of the
stack cabinet.
The ventilation space under the ceiling has to be at least
300 cm2.
the larger the ventilation space, the more energy-saving the
appliance is in operation.
, the distance between appliance and wall has to be at
Fig. 9 (2)
Fig. 9 (1)
to the height of the row of units,
can be fitted above the appli-
Fire and overheating hazard!
u
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type plate
(see Appliance at a glance).
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance can
be quickly disconnected from the supply in an emergency. It
must be outside the area of the rear of the appliance.
u
u
WARNING
Do not use extension cables or multiple socket outlets.
Check the electrical connection.
Plug in the power plug.
4.7 Switching on the appliance
Press On/Off button
u
The temperature display indicates the current temperature.
w
The interior light is on when the door is open.
w
If “DEMO” is displayed, demo mode is activated. Please
w
contact the after sales service.
Fig. 3 (3)
.
5 Control
5.1 Brightness of the temperature display
You can adjust the brightness of the temperature display to the
light conditions of the room in which the appliance is installed.
5.1.1 Adjusting the brightness
The brightness is adjustable between h0 (no illumination) and
h5 (maximum luminosity).
8 * Depending on model and options
To activate the setting mode: press SuperCool button
u
Fig. 3 (2)
w
The display indicates c.
The menu symbol
w
Using the Up setting button
u
button
To confirm: briefly press the SuperCool button
u
To set the display brighter: press the Up
u
setting button
To set the display darker: press the Down
u
setting button
To confirm: briefly press the SuperCool
u
button
The brightness is adjusted to the new value.
w
To deactivate the setting mode: press the On/Off button
u
Fig. 3 (3)
-or-
Wait for 5 minutes.
u
The temperature is indicated again in the temperature
w
display.
for about 5s.
Fig. 3 (6)
Fig. 3 (7)
Fig. 3 (6)
Fig. 3 (2)
.
Fig. 3 (5)
, select h.
.
.
.
shines.
Fig. 3 (7)
and Down setting
Fig. 3 (2)
Control
5.4 Food refrigeration
Note
The energy consumption increases and the cooling performance decreases if the ventilation is inadequate.
Always keep the air slits of the fan free.
u
.
Store perishable food such as ready-to-serve dishes, meat
u
products and sausages in the coldest zone. Place butter
and preserves in the upper area and in the door (see Appliance at a glance).*
Use recyclable plastic, metal, aluminium and glass
u
containers and cling film for wrapping.
Use the front area of the refrigerator compartment floor only
u
for briefly putting down cooled products, e.g. when rearranging and sorting. However do not leave cooled products
there otherwise they may be pushed back or tipped over
when the door is closed.
Do not store food too close together to enable good air
u
circulation.
To safeguard bottles from tipping over: move the bottle
u
holder.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently switched
off by playing children.
5.2.1 Setting the child lock function
To activate the setting mode: press SuperCool button
u
Fig. 3 (2)
w
The display indicates c.
The menu symbol
w
Briefly press theSuperCool button
u
When c1 is indicated in the display:
to activate the child lock, briefly press the
u
SuperCool button
w
The child lock symbol
display.
When c0 is indicated in the display:
to deactivate the child lock, briefly press the SuperCool
u
button
w
The child lock symbol
display.
To deactivate the set-up mode: press On/Off button
u
Fig. 3 (3)
-or-
Wait for 5 minutes.
u
The temperature is indicated again in the temperature
w
display.
for about 5 s.
Fig. 3 (2)
.
Fig. 3 (5)
Fig. 3 (2)
.
shines.
.
Fig. 3 (11)
Fig. 3 (11)
Fig. 3 (2)
shines. c flashes in the
goes out. c flashes in the
to confirm.
5.5 Setting the temperature
The temperature depends on the following factors:
the frequency of opening the door
-
the room temperature of the installation location
-
the type, temperature and quantity of the food
-
The temperature can be set from 9 °C to 2 °C, the recommended temperature is 5 °C.
For a higher temperature setting: press Up button
u
For a lower temperature setting: press Down button
u
Fig. 3 (6)
When the button is pressed the first time, the previously set
w
value is indicated, flashing, in the temperature display.
To change the temperature in 1 °C steps: briefly press the
u
button.
To change the temperature continuously: hold down the
u
button.
The value is displayed flashing during the setting operation.
w
The actual temperature is displayed about 5 s after the last
w
press of a button. The temperature slowly adjusts to the new
value.
.
Fig. 3 (7)
5.6 SuperCool
With SuperCool you switch to the highest cooling
performance to reach lower cooling temperatures.
Use SuperCool, to rapidly cool large amounts of
food.
When SuperCool is activated, the fan* runs. The appliance
operates with maximum refrigeration. The noise of the refrigeration unit may be temporarily louder as a result.
The SuperCool function uses slightly more energy.
.
5.3 Door alarm*
If the door is open for longer than 60 seconds, the
audible warning will sound.
The audible alarm is automatically silenced when
the door is closed.
5.3.1 Muting the door alarm*
The audible alarm can be muted when the door is open. The
sound switch-off function is active as long as the door is left
open.
Press alarm button
u
The door alarm is silenced.
w
Fig. 3 (1)
.
5.6.1 Cooling with SuperCool
Briefly press SuperCool button
u
The SuperCool symbol
w
The cooling temperature drops to the coldest value. Super-
w
Cool is activated.
SuperCool is automatically deactivated after 6 to12 hours
w
The appliance continues to operate in the energy-saving,
normal mode.
Fig. 3 (2)
Fig. 3 (12)
.
lights up in the display.
5.6.2 To prematurely deactivate SuperCool
Briefly press SuperCool button
u
The SuperCool symbol
w
SuperCool is deactivated.
w
Fig. 3 (2)
Fig. 3 (12)
.
goes out in the display.
* Depending on model and options 9
Control
5.7 Fan
With the fan you can rapidly cool large quantities of
fresh food or achieve a relatively even distribution of
temperature across all the storage levels.
The forced-air cooling is to be recommended:
at high room temperature (above33 °C )
-
at high humidity
-
The forced-air cooling uses slightly more energy. To save
energy, the fan switches off automatically when the door is
open.
5.7.1 Switching on the fan
Briefly press the fan button
u
The fan symbol
w
The fan is active. It switches on automatically when the
w
compressor runs.
Fig. 3 (10)
Fig. 3 (8)
shines.
.
5.7.2 To switch off the fan
Briefly press the fan button
u
The fan symbol
w
The fan is switched off.
w
Fig. 3 (10)
Fig. 3 (8)
goes out.
.
5.8 Shelves
5.10 Door racks
5.10.1 Moving the storage rack
Remove storage rack according to
u
illustration.
The boxes can be removed
and placed on the table as a
single unit.
Three small boxes are available through the customer service
as optional equipment instead of one wide and one small box.
Either one or both the boxes can be used. If particularly tall
bottles are to be stored, hang only a single box above the bottle
rack.
Re-positioning the boxes:
u
Lift them for removal and reposition them as required.
5.8.1 Relocating the shelves
The shelves have stops preventing them from being unintentionally pulled out.
Lift the shelf and draw it out
u
forwards.
Insert shelf with the raised
u
edge pointing upwards at
the back.*
The food does not freeze
w
onto the rear wall.
5.8.2 Dismantling shelves
The shelves can be
u
dismantled for cleaning.
5.9 Using the sectioned shelf
5.10.2 Dismantling door racks
*
Fig. 11
*
The door racks can be dismantled for cleaning.
u
5.11 Removing the bottle holder
Always take hold of the bottle holder
u
on the plastic part.
Fig. 10
The glass shelf with stop face (2) has to be at the back.
u
10 * Depending on model and options
Maintenance
5.12 Vegetable bins
To remove the vegetable bins:
pull the vegetable bin all the way out and tilt it forwards a
u
little.
In the case of the bottom drawer, the drawer locking device
w
is additionally released and the vegetable bin can be
removed.
Push the projecting telescopic slides back in.
u
To insert the vegetable bins:
place the vegetable bin on the telescopic slides and push to
u
the rear, exerting slight pressure.
In the case of the bottom drawer, the drawer locking device
w
additionally engages and the vegetable drawer sits firmly on
the telescopic slides.
6 Maintenance
6.1 Cleaning the appliance
Fig. 12
Fig. 13
NOTICE*
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accompanying care product.
Otherwise the surface coating will be affected.
Wipe the coated door surfaces using a soft, clean cloth
u
only. In case of stubborn dirt, use a little water or a neutral
cleaning agent. A microfibre cloth can be optionally used.
If the stainless steel side walls are dirty, clean them using
u
a commercially available stainless steel cleaning agent.
Then evenly apply the accompanying stainless steel care
product, making strokes in the direction of the grain.
Wipe side walls with a paint finish using a soft, clean
u
cloth only. In case of stubborn dirt, use a little water or a
neutral cleaning agent. A microfibre cloth can be optionally
used.
Clean drain hole: Remove deposits
u
with a narrow instrument, e.g. a
cotton bud.
Most of the parts can be dismantled for cleaning: see the
u
relevant chapter.
Clean items of equipment by hand with lukewarm water
u
and a little washing-up liquid.
Only use a damp cloth to clean the telescopic rails. The
u
grease in the runners is for lubrication purposes and must
not be removed.
After cleaning:
Wipe dry the appliance and items of equipment.
u
Connect the appliance and switch it on again.
u
Put the food back inside.
u
WARNING
Risk of injury and damage as a result of hot steam!
Hot steam can lead to burns and can damage the surfaces.
Do not use any steam cleaners!
u
NOTICE
Incorrect cleaning damages the appliance!
Do not use cleaning agents in concentrated form.
u
Do not use any scouring or abrasive sponges or steel wool.
u
Please do not use any aggressive, scouring, sand-,
u
chloride-, chemical- or acid-based cleaning agents.
Do not use chemical solvents.
u
Do not damage or remove the type plate on the inside of the
u
appliance. It is important for the customer service.
Do not pull off, bend or damage cables or other compo-
u
nents.
Do not allow any cleaning water to enter the drain channel,
u
ventilation grille or electrical parts.
Please use soft cleaning cloths and a universal pH-neutral
u
cleaning agent.
Please use cleaning and care products suitable for contact
u
with foodstuffs in the appliance interior.
Empty appliance.
u
Pull out the power plug.
u
Clean plastic outer and inner surfaces with lukewarm
u
water and a little washing-up liquid.
Do not apply stainless steel cleaning agent to glass or plastic
surfaces to prevent them from being scratched. Darker areas at
the beginning and quite an intensive colour of the stainless
steel surface are normal.*
6.2 Customer service
First check whether you can correct the fault yourself by reference to the list (see Malfunction). If this is not the case, please
contact the customer service whose address is given in the
enclosed customer service list.
WARNING
Risk of injury if repair work is not carried out professionally!
Have any repairs and action - not expressly specified - on
u
the appliance and mains cable carried out by service
personnel only. (see Maintenance)
Read the appliance
u
designation
Fig. 14 (1)
No.
Fig. 14 (2)
serial No.
off the type plate
located inside the
appliance on the lefthand side.
Notify the customer service, specifying the fault, appliance
u
designation
Fig. 14 (3)
This will help us to provide you with a faster and more accu-
w
rate service.
Keep the appliance closed until the customer service
u
arrives.
The food will stay cool longer.
w
, service
and
Fig. 14 (3)
Fig. 14 (1)
.
, service No.
Fig. 14 (2)
Fig. 14
and serial No.
* Depending on model and options 11
Malfunction
Pull out the mains plug (not by pulling the connecting cable)
u
or switch off the fuse.
7 Malfunction
Your appliance is designed and manufactured for a long life
span and reliable operation. If a malfunction nonetheless
occurs during operation, check whether it is due to a handling
error. In this case you will have to be charged for the costs
incurred, even during the warranty period. You may be able to
rectify the following faults yourself:
Appliance does not work.
The appliance is not switched on.
→
Switch on the appliance.
u
The power plug is not properly inserted in the wall socket.
→
Check power plug.
u
The fuse of the wall socket is not in order.
→
Check fuse.
u
The compressor runs for a long time.
The compressor switches to a low speed when little cold is
→
needed. Although the running time is increased as a result,
energy is saved.
This is normal in energy-saving models.
u
SuperCool is activated.
→
The compressor runs for longer in order to rapidly cool the
u
food. This is normal.
A LED on the bottom rear of the appliance (at the
compressor) flashes regularly every 15 seconds*.
The inverter is equipped with a diagnostic LED.
→
The flashing is normal.
u
Excessive noise.
Due to the various speed steps, speed-regulated*
→
compressors can generate different running noises.
The sound is normal.
u
A bubbling and gurgling noise.
This noise comes from the refrigerant flowing in the refriger-
→
ation circuit.
The sound is normal.
u
A quiet clicking noise.
The noise is produced whenever the refrigeration unit
→
(motor) automatically switches on or off.
The sound is normal.
u
A hum. It is briefly a little louder when the refrigeration
unit (the motor) switches on.
The refrigeration increases automatically when the Super-
→
Cool function is activated, fresh food has just been placed
in the appliance or the door has been left open for a while.
The sound is normal.
u
The ambient temperature is too high.
→
Solution: (see 1.2)
u
A low hum.
The sound is produced by air flow noise of the fan.
→
The sound is normal.
u
Vibratory noise.
The appliance is not fixed to the ground. The running of the
→
cooling unit therefore makes objects and adjacent furniture
vibrate.
Adjust appliance via the height-adjustable feet.
u
Move bottles and containers apart.
u
The temperature display indicates: F0 to F9
There is a fault.
→
Please contact the after-sales service (see Maintenance).
u
DEMO shines in the temperature display.
The demo mode is activated.
→
Please contact the after-sales service (see Maintenance).
u
The outer surfaces of the appliance are warm*.
The heat of the refrigeration circuit is used to prevent
→
condensate from forming.
This is normal.
u
The temperature is not cold enough.
The door of the appliance is not properly closed.
→
Close the door of the appliance.
u
Insufficient ventilation.
→
Clear ventilation grilles.
u
The ambient temperature is too high.
→
Solution: (see 1.2) .
u
The appliance was opened too frequently or for too long.
→
Wait to see whether the appliance reaches the required
u
temperature by itself. If not, please contact the after sales
service (see Maintenance).
The temperature is incorrectly set.
→
Set the temperature to a colder setting and check after 24
u
hours.
The appliance is too close to a source of heat (stove, heater
→
etc).
Change the position of the appliance or the source of heat.
u
The interior light is not on.
The appliance is not switched on.
→
Switch on the appliance.
u
The door was open longer than 15 min.
→
The interior light automatically switches off if the door has
u
been open for about 15 min.
The LED illumination is defective or the cover is damaged:
→
WARNING
Risk of injury due to electric shock!
Live parts are located under the cover.
Have the LED interior light changed or repaired only by the
u
customer service or by specialized personnel trained for the
purpose.
Danger of injury by LED lamp!
The light intensity of the LED illumination corresponds to laser
class 1/1M.
If the cover is defective:
u
WARNING
Do not look into the illumination with optical lenses from the
immediate proximity. This can cause injury to the eyes.
8 Decommissioning
8.1 Switching off the appliance
Press On/Off button
u
approx. 2 seconds.
The temperature display is dark.
w
If the appliance cannot be switched off, the child
w
lock function is active (see 5.2) .
8.2 Taking the appliance out of service
Empty the appliance.
u
Pull out the power plug.
u
Clean the appliance (see 6.1) .
u
Leave the door open to prevent odour.
u
Fig. 3 (3)
for
12 * Depending on model and options
9 Disposing of the appliance
The appliance contains some reusable materials
and should be disposed of properly - not simply
with unsorted household refuse. Appliances which
are no longer needed must be disposed of in a
professional and appropriate way, in accordance
with the current local regulations and laws.
When disposing of the appliance, ensure that the refrigeration
circuit is not damaged to prevent uncontrolled escape of the
refrigerant it contains (data on type plate) and oil.
Disable the appliance.
u
Pull out the plug.
u
Cut through the connecting cable.
u
Disposing of the appliance
* Depending on model and options 13
Disposing of the appliance
14 * Depending on model and options
Loading...