„theREALthing#1“ Manual
„theREALthing#1“ Manual / Overview
Notice
© LichtLogistik LED Support GmbH, All Rights Reserved
Information and specifications in this document are subject to change without notice. LichtLogistik LED Support GmbH assumes no
responsibility or liability for any errors or inaccuracies that may appear in this manual. Trademarks used in this text: „LichtLogistik LED
Support GmbH" and „theREALthing#1“ are registered trademarks.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. LichtLogistik LED Support GmbH disclaims any proprietary interest in trademarks and trade names owned by others.
NOTICE OF INTELLECTUAL PROPERTY RIGHTS
„theREALthing#1“ is protected by trademark patents.
Contacting LichtLogistik LED Support GmbH
LichtLogistik LED Support GmbH
Bergstraße 73
93138 Lappersdorf
Deutschland
Tel: +49 941 8305882
www.lichtlogistik.de
Mail: info@licht-logistik.de
Important Safety Information
Instructions pertaining to continued protection against fire, electric shock,
and injury to persons are found throughout this manual.
Please read all instructions prior to assembling, mounting,
and operating this equipment.
„theREALthing#1“ Manual / Technical Data
Specifications Umbrella
Material : Textile impregnated with flame retardant (Florimp K Verde), Black/silver, B1
Size : Diameter: 148cm, Length: 90cm!
Depth incl. Manfrotto-Stud: 42cm
On request: Material in black/gold or black/whiteb
Diameter 100cm or 180cm
Specifications LED-Core:
Material: Plexiglas GS, Kömaprint
IC Type: SMD SK6812 RGBW
DC In: 5VDC
IP rating: IP20 / indoor use only
Screws: M3
Weight: 800g
LED Type: 201 PCs 4in1 SMD 5050 LED
Specifications LED-Controller:
Material: Aluminium black
PSU: Meanwell
max. Power: 75W
Input Voltage: 230VAC
Output Voltage: 5VDC
Schutzart: IP40 / indoor use only
Power In: Neutrik True1 input/output
DMX In/Out: Neutrik 5pol XLR male/female
!
„theREALthing#1“ Manual / Connections
Unpacking
You will receive Your new „theREALthing#1“ Dynamic in following parts:
* Umbrella & LED unit
* LED Controller incl. PSU
* Neutrik True1 power cable
* 7pin LED connection cable
Open the umbrella and assemble it. Use eg. Manfrotto Superclamps.
Place LED unit in the umbrella. Fix it with the M4 Screw.
Connect LED unit with LED controller with the 7pin LED connection cable. Put it through the hole in the umbrella.
Connect the LED controller to 230 VAC with the Neutrik True1 power cable.
Connect the DMX IN Connector via 5pin DMX cable.
Set DMX address or use one of the Stand Alone modes. Further information on page 5.
LED Out
230 VAC Power In
230 VAC Power Out
M6 Safety Ring
Manfrotto Stud
DMX In
DMX Out
USB port
operating LED
OLED Display
operating buttons
!
„theREALthing#1“ Manual / Display&Function
!
„theREALthing#1“ Manual / Display&Function
„theREALthing#1“ Manual / Built-in Presets
„theREALthing#1“ Manual / Troubleshooting
Device is not working on DMX mode
-
recheck your DMX output signal with another DMX device
-
check if the operating LED lights up green
-
be sure that you choose the DMX mode in main menu
Stand alone mode is not working
-
be sure that you are in the stand alone menu during the playback
Switches are not working
-
check if the the switches or the objects"are"blocked by dirt
-
clean the space between the switches carefully with a Q-Tip and a vacuum
-
check if the switch caps have all the same height - if not, adjust the height.
Operating LED is not working
-
check if the DMX mode of the device is running well
-
contact the Lichtlogistik LED Support service
OLED display is not working
-
check if the safety glass above the display is broken
-
check if the operating LED lights up green
-
contact the Lichtlogistik LED Support service
LED unit or single pixel sections are not working
-
check the connection cable on both sides
-
please check your mode selection
-
contact the Lichtlogistik LED Support service
In general:
Please do not use the mini USB port for charging other devices. This port is only to use for install & update the system software.
Do not upload unauthorized software or updates on the device - otherwise you will loose the warranty of the product.
Loading...