REPLACEMENT PARTS LIST FOR MODELS “M137” and “D137”.
MODELS: M137-CD137-C
REF.
NO.
1•
2Case & switch asm “130/260”13004610004610
3• Gasket,case/cover1267007267007
4Relay asm1002474147135
5Wire pkg1267014267014
6• Seal,thru wall term3003402003402
7• Plug,test2034090034090
8•
9Cord term & seal13, 4094071094072
10•
11Bearing,upper rotor1NANA
12• Guard1267008267008
13Float-polypropylene1034019034019
14• Arm & seal asm “130/260”13004741004741
15Case & switch asm “130/260”13004739004739
16Switch asm “130/260”13004740004740
¤Lead wire (gray)1NANA
17Rod,oat1001526001526
18
19
20• Seal,mtr hsg1267006267006
21• Washer,trst-nyl.875x.504x.050”1002140002140
22Bearing,sleeve-lower rotor1NANA
23Housing,pump-mach1137004137004
24• Oil,dielectric1267056267056
25Guide asm, oat rod1004676004676
26• Seal asm1267027267027
27Impeller14137006137006
28Base & plate1001509001509
29Strainer plate1137008137008
30• Screw .25-20x.75hhm-ss9001916001916
31• Screw,#6-32x.438/Rh/pan head/2004644004644
32• Screw,#10-24 x.375 Rhm-sl ss3001883001883
33• Screw,sem/10-24 x .375 Hh-sl 2002000002000
34• Screw,#6-32x.25rhm sl tc stlgr3001877001877
35Screw,.25-20x.875”Lg hh ss/4 012491012491
¤
DESCRIPTIONQTYNOTES
Handle
Clamp,strain relief
Seal,cord-asm
Housing,mtr-&str regal beloit
Housing,mtr-& str emd014797008642
Rotor asm 115/230v/1ph regal b
Rotor asm 115/230v/1ph emd004021004021
Rebuild kit
1267032267032
16NANA
1094032094032
11, 2
12
1004743004743
9/86
thru
04/18
002475002476
267005267005
• Items included in Rebuild Kit. ¤ Not shown in illustration
9/86
thru
Current
See page 7 for “M137” and “D137” illustration.
NOTES:
1) Motor. housing., bearing., stator & term. (Item 18) are preassembled at the factory and must be replaced as a unit. Stator is permanently attached
to the motor housing. plug (Item 7); seal, thru wall term. (Item 6) and bearing - upper (Item 11) are replaceable.
2) When ordering motor housing, bearing, stator and term. (Item 18) or rotor (Item 16) specify either GE or Emerson motor. GE motor can be identied
by (4) half oval slots spaced at 90° around the outside diameter or the stator. Emerson motor can be identied by (2) half oval slots or holes spaced
180° around the outside diameter of the stator.
3) If an “X” follows model no., or date mfg. on brass ID tag, consult factory for ordering any parts.
4) See FM0160 parts price sheet for listing of parts prices.
5) “NA” indicates, not applicable.
6) Clamp, strain relief (Item 8) is not sold separately, must order seal, cord asm (Item 10).