Lian Yi Da Science CM388CWAS User Manual

CM388CWAS Wireless Camera User Manual

Thank you for choosing this wireless camera, please read this manual carefully before you use

it, it will benefit you to use it better.

1. Introduction

CM388CWAS wireless camera uses ISM wave band which can transfer audio and video signal

in the frequency scope of 2400～2483MHz, it can be used in baby monitoring、patient custody、

security, surveillance, etc.

2. Basic Specifications

● Image sensor: 1/3 color CMOS sensor

●Support NTSC or PAL video system

●Display Size: NTSC: 510×496 PAL: 628×586

●Pixel Size: 9.2um×7.2um

●Video output: can be used as wired and also wireless

●Wireless frequency : 2.4GHz, 2.427GHz, 2.454GHz, 2.481GHz

●Audio modulation frequency: 6.0MHz

●Open transmission distance: 100m

●Rotating angle：electric rotating 270 degrees from left to right

rotating 90 degrees up and down by hand

●Size: ￠65x95mm

●Wight: 0.15kg

3. The entire sketch map

4. Installation

4.1. It is more convenient for you to see the stable environment when you install the

remote sense
window

power socket

POWER Exchange Key

Channel switch

AV output

Lens

Infrared
light

90 degree rotation

270 degree Rotation

CM388CWAS in a fixed position, or install it on the other places such as the desk、baby bed

nearby and so on.

4.2. Please install CM388CWAS in a better-lightened place, so you can get the clear picture.

4.3. Please install CM388CWAS in an open place, so the transferring distance will be farther.

z Please don’t install CM388CWAS in such places that have many metal objects or have many

obstructions between receiver, it will affect the transferring distance.

z Install it far from the high temperature environment as possible as you can, don’t use it near

the fire or wet place.

5. Operation illumination

5.1. When use this for the first time, put the power adapter(DC5V/1.5A) into the AC socket, put

the DC output into the 5V DC IN at the back of this wireless camera.

5.2. It is channel 1 (2400MHz) when the power position is in the〝CH1〞, 〝CH2〞is channel

2(2427MHz), “CH3” is channel 3(2454MHz), “CH4” is channel 4(2481MHz).

5.3. If the receiving picture is not clear enough, you can adjust the lens and then the picture will

become much better.

5.4. If you want to see different features, you can adjust the angles of the camera up and down, or

left and right, or enter rotating mode.

5.5. Key operation

1) Power on: under “off” mode, press the power key once, if the red indicator light is on, the

camera is on.

2) Speed change

Under “on” mode, press the key once (about 0.5S), camera will enter the mode of speed change 1;

press the key twice (about 0.5S), camera will enter the mode of speed change 2, press the key 3

times (about 0.5S), camera will enter the mode of speed change 3; press the key 4 times (about

0.5S), camera will enter the mode of speed change 4; press the key for the 5

th

time to stop running,

and then press the key for the 6th time, camera will enter the mode of speed change 1 again, then

repeat circularly.

①Speed change 1 mode: transfer about 5 circles/minute, the blue indicator light will be lightened

one time per 1S.

② The speed change 2 mode: transfer about 10 circles/minute, the blue indicator light will be

lightened one time per 0.8S.

③ The speed change 3 mode: transfer about 15 circles/minute, the blue indicator light will be

lightened one time per 0.5S.