LG.Philips LCD LC470WXN-SAA1 Specification

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

LC470WXN

Product Specification

SPECIFICATION

FOR

APPROVAL

)

(

Preliminary Specification

●

)

(

Final Specification

APPROVED BY

/

/

GeneralBUYER

-MODEL

SIGNATURE

DATE

47.0” WXGA TFT LCDTitle

LG Display Co., Ltd.SUPPLIER

LC470WXN*MODEL

SAA1(RoHS Verified)SUFFIX

*When you obtain standard approval,

please use the above model name without suffix

APPROVED BY

J.H. Yoon /Senior Manager

REVIEWED BY

K.Y.Jung / Manager

SIGNATURE

DATE

PREPARED BY

/

Please return 1 copy for your confirmation with

your signature and comments.

Ver. 0.2 Apr. 22, 2008

B.Y.Kim / Engineer

TV Product Development Dept.

LG Display Co., Ltd

1 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

LC470WXN

Product Specification

CONTENTS

CONTENTS

RECORD OF REVISIONS

GENERAL DESCRIPTION1

ABSOLUTE MAXIMUM RATINGS2

ELECTRICAL SPECIFICATIONS3

ELECTRICAL CHARACTERISTICS3-1

INTERFACE CONNECTIONS3-2

SIGNAL TIMING SPECIFICATIONS3-3

SIGNAL TIMING WAVEFORMS3-4

COLOR DATA REFERENCE3-5

POWER SEQUENCE3-6

OPTICAL SPECIFICATIONS4

MECHANICAL CHARACTERISTICS5

ITEMNumber

Page

1COVER

2

3

4

5

6

6

8

10

11

12

13

15

19

RELIABILITY6

INTERNATIONAL STANDARDS7

SAFETY7-1

EMC7-2

PACKING8

DESIGNATION OF LOT MARK8-1

PACKING FORM8-2

PRECAUTIONS9

MOUNTING PRECAUTIONS9-1

OPERATING PRECAUTIONS9-2

ELECTROSTATIC DISCHARGE CONTROL9-3

PRECAUTIONS FOR STRONG LIGHT EXPOSURE9-4

STORAGE9-5

HANDLING PRECAUTIONS FOR PROTECTION FILM9-6

Ver. 0.2 Apr. 22, 2008

22

23

23

23

24

24

24

25

25

25

26

26

26

26

2 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

LC470WXN

Product Specification

RECORD OF REVISIONS

DescriptionPageRevision DateRevision No.

First Draft -Mar, 07, 20080.1

Change the company’s name-Apr, 22, 20080.2

Ver. 0.2 Apr. 22, 2008

3 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

1. General Description

The LC470WXN is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive display type which is operating in the normally black mode. It has a 46.96 inch diagonally
measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 16.7M(true) colors.
It has been designed to apply the 8-bit 1-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

LC470WXN

Product Specification

+12.0V

LVDS

1Port

CN1

(30pin)

+24.0V, GND, VBR-A
EXTVBR-B

+24.0V, GND

General Features

EEPROM

SCL

Timing Controller

[LVDS Rx + DCR + ODC

integrated]

Power Circuit

Block

Inverter(Master)

Inverter(Slave)

46.96 inch (1192.95mm) diagonalActive Screen Size

1096.0(H) x 640.0 (V) x 51 mm(D) (Typ.)Outline Dimension

0.76125 mm x 0.76125 mmPixel Pitch

1366 horiz. by 768 vert. Pixels, RGB stripe arrangementPixel Format

8-bit, 16.7 M colorsColor Depth

500 cd/m2 (Center 1point ,Typ.)Luminance, White

Viewing angle free ( R/L 178 (Typ.), U/D 178 (Typ.))Viewing Angle (CR>10)

SDA

Mini-LVDS(RGB)

G1

Gate Driver Circuit

G768

3PinX1CN(High)

3PinX1CN(High)

Source Driver Circuit

S1 S1366

TFT - LCD Panel

(1366 × RGB × 768 pixels)

Back light Assembly

Total 227.1W(typ.)(Logic=4.1W, Backlight=223W [VBR-A=1.65V])Power Consumption

14.7Kg(Typ)Weight

Transmissive mode, Normally blackDisplay Mode

Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 13%)Surface Treatment

Ver. 0.2 Apr. 22, 2008

4 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.

Table 1. ABSOLUTE MAXIMUM RATINGS

Parameter Remark

Symbol

LC470WXN

Product Specification

Value

Unit

MaxMin

Power

Input

Voltage

LCM

VDC+27.0-0.3VBLBacklight inverter

VDC+5. 5-0.3VON/OFFON/OFF Control Voltage

VDC+5.00VBRBrightness Control Voltage

+500TOPOperating Temperature

+60-20TSTStorage Temperature

°C

°C

%RH9010HOPOperating Ambient Humidity

%RH9010HSTStorage Humidity

Notes : 1. Temperature and relative humidity range are shown in the figure below.

Wet bulb temperature should be 39 °C Max. and no condensation of water.

2. Gravity mura can be guaranteed under 40℃condition.

90%

60

60%

Wet Bulb
Temperature [°C]

30

20

10

0

50

40

40%

Humidity [(%)RH]

10%

at 25 ± 2 °CVDC+14.0-0.3VLCD

Note 1,2

Storage

Operation

10 20 30 40 50 60 70 800-20

Dry Bulb Temperature [°C]

Ver. 0.2 Apr. 22, 2008

5 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3. Electrical Specifications

3-1. Electrical Characteristics

It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the CCFL
backlight and inverter circuit.

Table 2. ELECTRICAL CHARACTERISTICS

Parameter Symbol

LC470WXN

Product Specification

Value

NoteUnit

MaxTypMin

Circuit :

ILCDPower Input Current

Notes : 1. The specified current and power consumption are under the V

condition whereas mosaic pattern(8 x 6) is displayed and fVis the frame frequency.

2. The current is specified at the maximum current pattern.

3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min)

White : 255Gray
Black : 0Gray

VDC12.61211.4VLCDPower Input Voltage

=12.0V, 25 ± 2°C, fV=60Hz

LCD

1mA448345-

2mA599460-

1Watt5.44.1-PLCDPower Consumption

3A3--IRUSHRush current

Mosaic Pattern(8 x 6)

Ver. 0.2 Apr. 22, 2008

6 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Parameter Symbol

Inverter :

LC470WXN

Product Specification

Values

NotesUnit

MaxTypMin

Power Supply
Input Current

Power Consumption

Input Voltage for

Control System

Signals

Lamp:

On/Off

On Vdc5.0-2.5V on

Off

Brightness Adjust

PWM Frequency for
NTSC & PAL

Pulse Duty
Level(PWM)

(Burst mode)

Vdc25.224.022.8VBLPower Supply Input Voltage

IBL_AAfter Aging

9.3-

10.0-

11.0-

IBL_BBefore Aging

12.0-

-PBL

10.3

11.0

12.0

13.0

250223

5.0-2.5High Level

0.8-0.0Low Level

VBR-A = 1.65V … 1A

VBR-A = 3.3V … 1A

VBR-A = 1.65V … 2A

VBR-A = 3.3V … 2A

VBL = 22.8V
Ext VBR-B = 100%

A14.0--IrushPower Supply Input Current (In-Rush)

VBR-A = 1.65V

V

Vdc3.31.650.0VBR-ABrightness Adjust

Vdc0.80.0-0.3V off

Vdc

Vdc

BR-A

1

1Vp-p0.5--Power Supply Input Voltage Ripple

= 1.65V … 1W

On Duty%100-34ExtVBR-B

5Hz100/120PAL/NTSC

HIGH: Lamp on

LOW:Lamp off

TsDischarge Stabilization Time

3sec100

4Hrs50,000Life Time

Notes :

1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 120

minutes at 25±2°C. The specified current and power consumption are under the typical supply Input voltage
24Vand VBR (VBR-A : 1.65V & ExtVBR-B : 100%), it is total power consumption.

The ripple voltage of the power supply input voltage is under 0.5 Vp-p. LGD recommend Input Voltage is

24.0V ± 5%.

2. Electrical characteristics are determined within 30 minutes at 25±2°C.

The specified currents are under the typical supply Input voltage 24V.

3. The brightness of the lamp after lighted for 5minutes is defined as 100%.
TS is the time required for the brightness of the center of the lamp to be not less than 95% at typical current.

The screen of LCD module may be partially dark by the time the brightness of lamp is stable after turn on.

4. Specified Values are for a single lamp which is aligned horizontally.
The life time is determined as the time which luminance of the lamp is 50% compared to that of initial value
at the typical lamp current (VBR-A : 1.65V & ExtVBR-B :100%), on condition of continuous operating at 25± 2°C

5. LGD recommend that the PWM freq. is synchronized with Two times harmonic of Vsync signal of system.

6. The duration of rush current is about 10ms.

Ver. 0.2 Apr. 22, 2008

7 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-2. Interface Connections

This LCD module employs two kinds of interface connection, a 30-pin connector is used for the module
electronics and Master 14-pin and Slave 12-pin connectors are used for the integral backlight system.

3-2-1. LCD Module

- LCD Connector(CN5) : IS100-L30B-C23 (Manufactured by UJU) or Equivalent

- Mating Connector : FI-30C2L (Manufactured by JAE) or Equivalent

Table 4. MODULE CONNECTOR(CN1) PIN CONFIGURATION

1

2
3
4

5

6
7
8

9

10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25

26

27
28
29
30

VLCD Power Supply +12.0V

Product Specification

Power Supply +12.0VVLCD
Power Supply +12.0VVLCD
Power Supply +12.0VVLCD

GroundGND

GroundGND
GroundGND
GroundGND

Select LVDS Data formatSelect

NCNC

GroundGND
LVDS Receiver Signal(-)RA­LVDS Receiver Signal(+)RA+
GroundGND
LVDS Receiver Signal(-)RB­LVDS Receiver Signal(+)RB+
GroundGND
LVDS Receiver Signal(-)RC­LVDS Receiver Signal(+)RC+
GroundGND
LVDS Receiver Clock Signal(-)RCLK­LVDS Receiver Clock Signal(+)RCLK+
GroundGND
LVDS Receiver Signal(-)RD­LVDS Receiver Signal(+)RD+

GroundGND

NCNC
NCNC

GroundGND
GroundGND

LC470WXN

NoteDescriptionSymbolPin No.

1

2

Notes: 1. The pin no 9 is an option pin for JEIDA or VESA format.

( VESA Format = “GND” / JEIDA Format =“VCC”) Please refer to Appendix for further details.

2. The pin no 30 is LCD Test option.
LCM operates “AGP” (Auto Generation Pattern) or “NSB” (No Signal Black) is case that LVDS signals
are out of frequency or abnormal condition in spite of 12 volt power supply.

LGD recommends “NSB”. ( AGP : “VCC” or “OPEN” / NSB : “GND” )

3. All GND (ground) pins should be connected together, which should be also connected to the LCD

module’s metal frame.

4. All VLCD (power input) pins should be connected together.

5. Input Levels of LVDS signals are based on the EIA 664 Standard.

Ver. 0.2 Apr. 22, 2008

8 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-2-2. Backlight Inverter

Master

-Inverter Connector : S14B-PH-SMC

(manufactured by JST) or Equivalent

- Mating Connector : PHR-14 or Equivalent

Table 5. INVERTER CONNECTOR PIN CONFIGULATION

Product Specification

Slave

-Inverter Connector : S12B-PH-SMC

-Mating Connector : PHR-12 or Equivalent

Master

LC470WXN

(manufactured by JST) or Equivalent

Slave

NoteDescriptionSymbolPin No

1

2

3

4

5

6

7

8

9

10

11

12

13

VBR-A

ON/OFF

ExtVBR-B

Power Supply +24.0VVBL

Power Supply +24.0VVBL

Power Supply +24.0VVBL

Power Supply +24.0VVBL

Power Supply +24.0VVBL

Backlight GroundGND

Backlight GroundGND

Backlight GroundGND

Backlight GroundGND

Backlight GroundGND

Analog dimming voltage
DC 0.0V ~ 3.3V (Typ : 1.65V)

Burst Dimming Control
PWM signal input

VBL

VBL

VBL

VBL

VBL

GND

GND

GND

GND

GND

External PWM

14

Notes : 1. GND should be connected to the LCD module’s metal frame.

2. Minimum Brightness : VBR-A = 0.0V Maximum Brightness : VBR-A = 3.3V “OPEN” : VBR-A = 1.65V

3. Rising Edge : Lamp “ON” / Falling Edge : Lamp “OFF”

4. Pin#13 can be opened. ( if Pin #13 is open , Ext VBR-B is 100% )

5. Pin#14 can be opened. (GND or NC)

6. Each impedance of pin #11,12 and 13 is 143.9[KΩ],37.6[KΩ],54.9[KΩ]

Don’t careOn/Off0.0V ~ 5.0VV

VBL

VBL

VBL

VBL

VBL

GND

GND

GND

GND

GND

-

1

2, 3Don’t careVBR-A

3, Open/High for B/L

on as default

4

5-GNDPOWER GNDGND

◆◆◆◆ Rear view of LCM

14

…

PCB

…

1

PCB

…

…

1

<Master>

Ver. 0.2 Apr. 22, 2008

12

<Slave>

9 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-3. Signal Timing Specifications

Table 6 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal timing
should be satisfied with the following specification for normal operation.

LC470WXN

Product Specification

Table 6. TIMING TABLE for NTSC &PAL

DCLK

Horizontal Blank

Hsync

[ DE (Data Enable) Only ]

NoteUnitMaxTypMinSymbolITEM

ns15.813.812.5tCLKPeriod

MHz8072.463-Frequency

tCLK192015281456tHTPeriod

tCLK136613661366tHVHorizontal Valid

-

tHP- tHV162tHP- tHV

5047.445fHFrequency

-5024tHBPHorizontal Back Porch

-8040tHFPHorizontal Front Porch

KHz

tCLK-32-tWHWidth

tHP1063790776tVTPeriod

tHP768768768tVVVertical Valid

tHPtVP- tVV22tVP- tVV-Vertical Blank

Vsync

-21tVFPVertical Front Porch

Hz636047fVFrequency

tHP-5-tWVWidth

Hz-155tVBPVertical Back Porch

tHP

Note :

1. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate.

2. Above Timing Tables are only valid for DE Mode.

Ver. 0.2 Apr. 22, 2008

Note 1)
PAL : 47~53Hz
NTSC : 57~63Hz

10 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-4. Signal Timing Waveforms

LC470WXN

Product Specification

DE, Data

DCLK

tCLK

Data

DE(Data Enable)

0.5 VDD

Invalid data

* Reference : Sync. Relation

HSync

tWH

Valid data

Pixel 0,0

Pixel 2,0

tHP

0.7VDD

0.3VDD

Invalid data

* tHB = tHFP + tWH +tHBP

* tVB = tVFP + tWV +tVBP

tHBP tHV

DE(Data Enable)

tVP

tWV

VSync

tVBP

DE(Data Enable)

Ver. 0.2 Apr. 22, 2008

tVV tVFP

tHFP

11 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-5. Color Data Reference

The brightness of each primary color(red,green,blue) is based on the 8-bit gray scale data input for the color.
The higher binary input, the brighter the color. Table 7 provides a reference for color versus data input.

Table 7. COLOR DATA REFERENCE

LC470WXN

Product Specification

Input Color Data

Basic
Color

RED

Color

Black 0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0

Red (255)

Green (255)

Blue (255)

Cyan

Magenta

Yellow

White

MSB LSB

RED

GREEN

MSB LSB

BLUE

MSB LSB

B7 B6 B5 B 4 B3 B2 B1 B0G7 G6 G5 G4 G3 G2 G1 G0R7 R6 R5 R4 R3 R2 R1 R0

0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 1

0 0 0 0 0 0 0 01 1 1 1 1 1 1 10 0 0 0 0 0 0 0

1 1 1 1 1 1 1 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0

1 1 1 1 1 1 1 11 1 1 1 1 1 1 10 0 0 0 0 0 0 0

1 1 1 1 1 1 1 10 0 0 0 0 0 0 01 1 1 1 1 1 1 1

0 0 0 0 0 0 0 01 1 1 1 1 1 1 11 1 1 1 1 1 1 1

1 1 1 1 1 1 1 11 1 1 1 1 1 1 11 1 1 1 1 1 1 1

0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0RED (000) Dark

0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 1RED (001)

............

0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 0RED (254)

0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 1RED (255)

0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0GREEN (000) Dark

0 0 0 0 0 0 0 00 0 0 0 0 0 0 10 0 0 0 0 0 0 0GREEN (001)

GREEN

0 0 0 0 0 0 0 01 1 1 1 1 1 1 00 0 0 0 0 0 0 0GREEN (254)

0 0 0 0 0 0 0 01 1 1 1 1 1 1 10 0 0 0 0 0 0 0GREEN (255)

BLUE (000) Dark

0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0

0 0 0 0 0 0 0 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (001)

BLUE

1 1 1 1 1 1 1 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (254)

1 1 1 1 1 1 1 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (255)

Ver. 0.2 Apr. 22, 2008

............

............

12 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-6. Power Sequence

3-6-1. LCD Driving circuit

LC470WXN

Product Specification

Power Supply For LCD

V

LCD

Interface Signal (Tx)

Option Signal

(LVDS_select, BIT_select)

Power for Lamp

Table 8. POWER SEQUENCE

Parameter

0V

0V

10%

90%

T1

T2

Invalid
Data

T7 T8

Valid Data

T3 T4

Lamp ON

Value

MaxTypMin

--200T4

-

-

T2

-

Invalid
Data

T5

Unit

ms20-0.5T1

ms--0T2

ms--200T3

ms

ms--0T5

s--2.0T6

ms0T7

ms0T8

90%

10%

T6

Notes

4

3

3

5

4

4

Note : 1. Please avoid floating state of interface signal at invalid period.

2. When the interface signal is invalid, be sure to pull down the power supply V

LCD

to 0V.

3. The T3/T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.

4. If the on time of signals(Interface signal and Option signals) precedes the on time of Power(V
check the LCD logic Power(Vcc) is under 0.8V, otherwise it will be happened abnormal display.

5. T6 should be measured after the Module has been fully discharged between power off and on

period.

Ver. 0.2 Apr. 22, 2008

),

LCD

13 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

3-6-2. Sequence for Inverter

Power Supply For Inverter

VBL

10%

0V

LC470WXN

Product Specification

24V (typ.)

90%

0.7V

T1 T2 T3 T2

VON/OFF

VBR-A &
EXTVBR-B

3-6-3. Deep condition for Inverter

VBL(Typ.) x 0.8

Table 9. Power Sequence for Inverter

Parameter

1000ms (Min) 1000ms (Min)

T5

Lamp ON

T4

T7

T6

T4

V

: 24V

BL

0 V

Values

MaxTypMin

-

Units

ms--20T1

ms--500T2

ms--200T3

ms--10T5

VBL(Typ) x 0.8ms10--T6

Remarks

1

2ms0T4

3ms--1000T7

Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time.

2. T4(max) is less than T2.

3. In T7 section, EXTVBR-B is recommended 100%.

Ver. 0.2 Apr. 22, 2008

14 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

4. Optical Specification

Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at 25±2°C.
The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of Φ and θ
equal to 0 °.
FIG. 1 shows additional information concerning the measurement equipment and method.

LC470WXN

Product Specification

Optical Stage(x,y)

LCD Module

FIG. 1 Optical Characteristic Measurement Equipment and Method

Table 10. OPTICAL CHARACTERISTICS

Ta= 25±2°C, V

SymbolParameter

Contrast Ratio

Surface Luminance, white

Luminance Variation

Gray-to-Gray

RED

GREEN

Color Coordinates
[CIE1931]

BLUE

WHITE

Viewing Angle (CR>10)

x axis, right(φ=0°)
x axis, left (φ=180°)
y axis, up (φ=90°)
y axis, down (φ=270°)

WH

WHITE

Rx

Pritchard 880 or
equivalent

50cm

=12.0V, fV=60Hz, Dclk=72.4MHz VBR-A=1.65V, EXTVBR-B=100%

LCD

Typ

-0.03

Value

0.634

0.333Ry

0.291Gx

0.611Gy

0.146Bx

0.061By

0.279Wx

0.292Wy

MaxTypMin

-500400L

Typ

+0.03

--89θr

--89θl

--89θu

--89θd

--- 6Gray Scale

2

ms

NoteUnit

1-1100800CR

2cd/m

31.3--5Pδ

4128-G to GResponse Time

5degree

Ver. 0.2 Apr. 22, 2008

15 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Notes :1. Contrast Ratio(CR) is defined mathematically as :

CR(Contrast Ratio) = Maximum CRn (n=1, 2, 3, 4, 5)

Surface Luminance at position n with all white pixels

CRn =

Surface Luminance at position n with all black pixels

n = the Position number(1, 2, 3, 4, 5). For more information, see FIG 2.

2. Surface luminance are determined after the unit has been ‘ON’ and 30min after lighting the

backlight in a dark environment at 25±2°C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 2.

3. The variation in surface luminance , δ WHITE is defined as :
δ WHITE(5P) = Maximum(L

Where L
For more information, see the FIG. 2.

on1

to L

are the luminance with all pixels displaying white at 5 locations .

on5

Product Specification

, L

, L

on1,Lon2

on3

on4

, L

) / Minimum(L

on5

on1,Lon2

, L

on3

, L

on4

LC470WXN

, L

)

on5

4. Response time is the time required for the display to transition from G(N) to G(M) (Rise Time, TrR)

and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M)
※ G to G Spec is average of measured time

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are

determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 4.

6. Gray scale specification

Gamma Value is approximately 2.2. For more information, see the Table 11.

Table 11. GRAY SCALE SPECIFICATION

Gray Level

L0

L15

L31

L47

L63

L79

L95

L111

L127

L143

L159

L175

L191

L207

L223

L239

L255

Luminance [%] (Typ.)

0.091

0.20

0.97

2.42

4.61

7.59

11.4

16.0

21.6

28.0

35.4

43.7

53.0

63.2

74.5

86.7

100

Ver. 0.2 Apr. 22, 2008

16 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Measuring point for surface luminance & measuring point for luminance variation.

LC470WXN

Product Specification

H

A

③③③③②②②②

V

①①①①

B

A : H / 4 mm

④④④④

FIG. 2 5 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Gray(M)”.

TrR

100

90

⑤⑤⑤⑤

TrD

B : V / 4 mm
@ H,V : Active Area

Optical
Response

10

0

Ver. 0.2 Apr. 22, 2008

Gray(N)

N,M = Black~White, N<M

FIG. 3 Response Time

Gray(M)

Gray(N)

17 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

Dimension of viewing angle range

φ

= 180°, Left

Product Specification

Normal

E

θ

φ

Y

φ

= 90°, Up

LC470WXN

φ

= 270°, Down

FIG. 4 Viewing Angle

φ

= 0°, Right

Ver. 0.2 Apr. 22, 2008

18 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

5. Mechanical Characteristics

Table 12 provides general mechanical characteristics.

Table 12. MECHANICAL CHARACTERISTICS

LC470WXN

Product Specification

ValueItem

Outline Dimension

Bezel Area

Active Display Area

Horizontal

Vertical

Depth

Horizontal

Vertical

Horizontal

Vertical

14.7Kg(Typ) ,15.44Kg(Max.)Weight

1096.0 mm

640.0 mm

51.0 mm

1049.0 mm

593.0 mm

1039.8675 mm

584.64 mm

Note : Please refer to a mechanic drawing in terms of tolerance at the next page.

Ver. 0.2 Apr. 22, 2008

19 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

<FRONT VIEW>

LC470WXN

Product Specification

Ver. 0.2 Apr. 22, 2008

20 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

<REAR VIEW>

LC470WXN

Product Specification

Ver. 0.2 Apr. 22, 2008

21 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

6. Reliability

Table 13. ENVIRONMENT TEST CONDITION

LC470WXN

Product Specification

ConditionTest ItemNo.

Ta= 60°C 240h High temperature storage test1

Ta= -20°C 240hLow temperature storage test2

Ta= 50°C 50%RH 240hHigh temperature operation test3

Ta= 0°C 240hLow temperature operation test4

Wave form : random

Vibration test

5

(non-operating)

Shock test

6

(non-operating)

Altitude operating

8

storage / shipment

Vibration level : 1.0Grms
Bandwidth : 10-300Hz
Duration : X,Y,Z, 30 min

One time each direction

Shock level : 50G(X,Y axis), 35G(Z axis)
Waveform : half sine wave, 11ms
Direction : ±X, ±Y, ±Z

One time each direction

Ta= 40 °C ,90%RHHumidity condition Operation7

0 - 15,000 ft
0 - 40,000 ft

Note : Before and after Reliability test, LCM should be operated with normal function.

Ver. 0.2 Apr. 22, 2008

22 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

7. International Standards

7-1. Safety

a) UL 60065, 7thEdition, dated June 30, 2003, Underwriters Laboratories, Inc.,

Standard for Audio, Video and Similar Electronic Apparatus.

b) CAN/CSA C22.2, No. 60065:03, Canadian Standards Association,

Standard for Audio, Video and Similar Electronic Apparatus.

c) IEC60065:2001, 7thEdition CB-scheme and EN 60065:2002,

Safety requirements for Audio, Video and Similar Electronic Apparatus..

LC470WXN

Product Specification

7-2. EMC

a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and

Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),
1992

b) CISPR13 "Limits and Methods of Measurement of Radio interference characteristics of Sound

and Television broadcast receivers and associated equipment"

CISPR22 "Limits and Methods of Measurement of Radio interference characteristics of Information

Technology Equipment" International Special Committee on Radio Interference.

c) EN55013 "Limits and Methods of Measurement of Radio interference characteristics of Sound and

Television broadcast receivers and associated equipment"

EN55022 "Limits and Methods of Measurement of Radio interference characteristics of Information

Technology Equipment" European Committee for Electro Technical Standardization.(CENELEC),
1988(Including A1:2000)

Ver. 0.2 Apr. 22, 2008

23 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

8. Packing

8-1. Designation of Lot Mark

a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH)
D : YEAR E : MONTH
F : PANEL CODE G : FACTORY CODE
H : ASSEMBLY CODE I,J,K,L,M : SERIAL NO.

LC470WXN

Product Specification

Note

1. YEAR

Year

Mark

321

200452005

4

200320022001

2006720078200892009

6

2. MONTH

Month

Mark

Apr5May

4

Jun7Jul8Aug9Sep

6

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one Pallet : 12 pcs

b) Pallet Size : 1300mm X 1140mm X 860mm

2010

0

Oct

A

Nov

B

DecMarFebJan

C421

Ver. 0.2 Apr. 22, 2008

24 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

9. Precautions

Please pay attention to the followings when you use this TFT LCD module.

9-1. Mounting Precautions

(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the

module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.

(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.

Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former

generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.

(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB

pencil lead. And please do not rub with dust clothes with chemical treatment.

Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental

to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like

chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.

(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes

deformations and color fading.

(9) Do not open the case because inside circuits do not have sufficient strength.

LC470WXN

Product Specification

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :

V=±200mV(Over and under shoot voltage)

(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)

And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer

(4) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or

electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be

done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.

(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated

its full characteristics perfectly.

(8) A screw which is fastened up the steels should be a machine screw.

(if not, it can causes conductive particles and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) It is recommended to avoid the signal cable and conductive material over the inverter transformer

for it can cause the abnormal display and temperature rising.

(11) Partial darkness may happen during 3~5 minutes when LCM is operated initially in condition that

luminance is under 40% at low temperature (under 5℃). This phenomenon which disappears naturally

after 3~5 minutes is not a problem about reliability but LCD characteristic.

Ver. 0.2 Apr. 22, 2008

25 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage

When storing modules as spares for a long time, the following precautions are necessary.

LC470WXN

Product Specification

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature

between 5°C and 35°C at normal humidity.

(2) The polarizer surface should not come in contact with any other object.

It is recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape

When the protection film is peeled off, static electricity is generated between the film and polarizer.

This should be peeled off slowly and carefully by people who are electrically grounded and with well ion­blown equipment or in such a condition, etc.

(2) When the module with protection film attached is stored for a long time, sometimes there remains a very

small amount of glue still on the bezel after the protection film is peeled off.

(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,

please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal­hexane.

.

Ver. 0.2 Apr. 22, 2008

26 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

# APPENDIX-I-1

■ Required signal assignment for Flat Link (DS90C385) Transmitter (Pin9=“L”)

LC470WXN

Product Specification

Host System

24 Bit

RED0
RED1
RED2
RED3
RED4
RED5
RED6

RED7
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7

BLUE0
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7

Hsync
Vsync

Data Enable

CLOCK

DS90C385

or Compatible

51
52
54
55
56
3
50
2
4
6
7
11
12
14
8
10
15
19
20
22
23
24
16
18
27
28
30
31

TxCLKOUT­TxCLKOUT+

TxOUT0­TxOUT0+

TxOUT1­TxOUT1+

TxOUT2­TxOUT2+

TxOUT3­TxOUT3+

FI-X30SSL-HF

48

47

46

45

42

41

40

39

38

37

GND

GND

12
13

15
16

18
19

21
22

24
25

30

Timing

Controller

100ΩΩΩΩ

100ΩΩΩΩ

100ΩΩΩΩ

100ΩΩΩΩ

100ΩΩΩΩ

9

RxIN0­RxIN0+

RxIN1­RxIN1+

RxIN2­RxIN2+

RxCLKIN­RxCLKIN+

RxIN3­RxIN3+

VESA / JEIDA

LCD Test

LCD Module

Notes:

1. The LCD module uses a 100 Ohm(Ω) resistor between positive and negative lines
of each receiver input.

2. Refer to LVDS transmitter data sheet for detail descriptions. (THC63LVD823 or Compatible)

3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver. 0.2 Apr. 22, 2008

27 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

# APPENDIX-I-2

■ Required signal assignment for Flat Link (DS90C385) Transmitter (Pin9=“H”)

LC470WXN

Product Specification

Host System

24 Bit

RED0
RED1
RED2
RED3
RED4
RED5
RED6

RED7
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7

BLUE0
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7

Hsync
Vsync

Data Enable

CLOCK

DS90C385

or Compatible

50
2
51
52
54
55
56
3
8
10
4
6
7
11
12
14

16
18
15
19
20
22
23
24
27
28
30
31

TxCLKOUT­TxCLKOUT+

TxOUT0­TxOUT0+

TxOUT1­TxOUT1+

TxOUT2­TxOUT2+

TxOUT3­TxOUT3+

FI-X30SSL-HF

48

47

46

45

42

41

40

39

38

37

GND

Vcc

12
13

15
16

18
19

21
22

24
25

30

Timing

Controller

100ΩΩΩΩ

100ΩΩΩΩ

100ΩΩΩΩ

100ΩΩΩΩ

100ΩΩΩΩ

9

RxIN0­RxIN0+

RxIN1­RxIN1+

RxIN2­RxIN2+

RxCLKIN­RxCLKIN+

RxIN3­RxIN3+

VESA / JEIDA
LCD Test

LCD Module

Notes:

1. The LCD module uses a 100 Ohm(Ω) resistor between positive and negative lines
of each receiver input.

2. Refer to LVDS transmitter data sheet for detail descriptions. (THC63LVD823 or Compatible)

3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.

Ver. 0.2 Apr. 22, 2008

28 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

# APPENDIX-II

■ Pallet Ass’y

LC470WXN

Product Specification

LCD Module1

Ver. 0.2 Apr. 22, 2008

MATERIALDESCRIPTIONNO.

47INCHBAG2

MASKING 20MMX50MTAPE3

PAPER 1300X1140X130MMPALLET4

EPSPACKING,BOTTOM5

EPSPACKING,TOP6

PAPER ANGLE,POST7

PAPERANGLE,PACKING8

STEELBAND,CLIP9

PPBAND10

OPPTAPE11

YUPO 80G 100X100LABEL12

29 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

LC470WXN

# APPENDIX 2

# APPENDIX- III

■ LCM Label

Model

UL, TUV Mark

LGD Logo

US PATENT No.

Product Specification

LC470WXN
(SA)(A1)

Serial No.

Origin

■■■■ Serial No. (See CAS 24page for more information)

1 2 3 4 5 6 7 9 10 11 12

Year

Inch

Ver. 0.2 Apr. 22, 2008

Month

M Ass’y Factory code

8

13

Serial No.

30 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

LC470WXN

# APPENDIX 3

# APPENDIX- IV

■ Pallet Label

Product Specification

LC470WXN

SAA1

12 PCS

MADE IN KOREA RoHS Verified

001/01-01

XXXXX XXXXXXXX XXX XXX XXXX

Ver. 0.2 Apr. 22, 2008

31 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

# APPENDIX- ⅤⅤⅤⅤ

■ Option Pin Circuit Block Diagram

Circuit Block Diagram of LVDS Format Selection pin

LC470WXN

Product Specification

1KΩΩΩΩ

Selector (Pin 9) Selector

50KΩΩΩΩ

ASIC

(TCON)

System Side LCM Side

Ver. 0.2 Apr. 22, 2008

32 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

# APPENDIX- VI

LVDS Input characteristics

1. DC Specification

LVDS -

LVDS +

LC470WXN

Product Specification

|VID|

0V

LVDS Common mode Voltage

2. AC Specification

1 ) LVDS Clock to data timing

LVDS Clock

LVDS Data

# |VID| = |(LVDS+) -(LVDS-)|
# VCM= {(LVDS+) + (LVDS-)}/2

CM

SKEW (Fclk

t

SKEW

t

= 1/T

V

CM

NotesUnitMaxMinSymbolDescription

-mV500200|VID|LVDS Differential Voltage

-V1.51.0V

T

c

clk

)

LVDS Clock to Data Skew Margin

Note> 1. If Tc=13.46ns , t

SKEW

SKEW

Min= - 480ps Max= + 480ps

Note 1ps+(Tc / 7)* 0.2- (Tc / 7)* 0.2t

Ver. 0.2 Apr. 22, 2008

NotesUnitMaxMinSymbolDescription

33 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

2 ) LVDS Clock timing

LVDS 1’st Clock

LVDS 2nd/ 3rd/ 4thClock

Product Specification

T

clk

LC470WXN

LVDS inter-port Clock Skew

T

skew_minTskew_max

< LVDS inter-port Clock timing >

T

skew

NotesUnitMaxMinSymbolDescription

-ns2.5-2.5

2/2

Ver. 0.2 Apr. 22, 2008

34 /36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

# APPENDIX- VII

■ LVDS Select : “H” Data-Mapping (JEIDA format)

RCLKP

LC470WXN

Product Specification

LVDS Data-Mapping info. (8bit)

RCLKM

RAP

RBP

RCP

RDP

R17 R16 R15 R14G12 R13R12’ R12R13’ G12”

B12 G17 G16 G15B13 G14G13’ G13G14’ B13”

V

SYNCHSYNC

B11 B10 G11 G10X R11R10’ R10R11’ X”

B17 B16DE B15B14’ B14B15’ DE”

■ LVDS Select : “L” Data-Mapping (VESA format)

RCLKP

RCLKM

RAP

R15 R14 R13 R12G10 R11R10’ R10R11’ G10”

RBP

RCP

RDP

Ver. 0.1

B10 G15 G14 G13B11 G12G11’ G11G12’ B15”

V

SYNCHSYNC

B17 B16 G17 G16X R17R16’ R16R17’ X”

B15 B14DE B13B12’ B12B13’ DE”

35 / 36

Global LCD Panel Exchange Center

www.panelook.com

One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!

www.panelook.com

−

# APPENDIX- VIII

Gray to Gray Response Time Uniformity

This is only the reference data of G to G and uniformity for LC470WXN-SAA1 model.

1. G to G Response Time :
Response time is defined as Figure3 and shall be measured by switching the input signal for
“Gray (N) ” and “Gray(M)”.(32Gray Step at 8bit)

2. G to G Uniformity
The variation of G to G Uniformity , δ G to G is defined as :

G to G Uniformity =

Product Specification

GtoGTypical

LC470WXN

)()(

GtoGTypicalGtoGMaximum

)(

≤1

*Maximum (GtoG) means maximum value of measured time (N, M = 0 (Black) ~ 255(White), 32 gray step).

0Gray

32Gray

64Gray

…

223Gray

255Gray

0Gray

TrD:32G0G

TrD:64G0G

…

TrD:223G0G

TrD:255G0G

TrD:255G223G…TrD:255G64GTrD:255G32G

255Gray223Gray…64Gray32Gray

TrR:0G225GTrR:0G223G…TrR:0G64GTrR:0G32G

TrR:32G255GTrR:32G223G…TrR:32G64G

TrR:64G255GTrR:64G223G…TrD:64G32G

…………

TrR:223G255G…TrD:223G64GTrD:223G32G

3. Sampling Size : 2 pcs

4. Measurement Method : Follow the same rule as optical characteristics measurement.

5. Current Status

Below table is actual data of production on Dec. 07, 2007 ( LGD RV Event Sample)

# 1

# 2

G to G Response Time [ms]

Min.

5.2

5.9

Max.

9.3

9.4

Uniformity

0.16

0.17

16

12

8

4

0

G255

G223

G191

G159

G95

G127

G63

G31

G255

G159

G63

G0

G255 G223

G191 G159

G127 G95

G63 G31

G0

16

12

8

4

0

G255

G223

G191

G159

G95

G127

G63

G31

G255

G159

G63

G0

< # 1 > < # 2 >

Ver. 0.2 Apr. 22, 2008

G255 G223

G191 G159

G127 G95

G63 G31

G0

36 /36