One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3/ 27
www.panelook.com
Global LCD Panel Exchange Center
1. General Description
The LC470WU1 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive display type which is operating in the normally black mode. It has a 46.96 inch diagonally
measured active display area with WUXGA resolution (1080 vertical by 1920 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arrayed in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 16.7M(true) colors.
It has been designed to apply the 8-bit 2-port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.
www.panelook.com
LC470WU1
Liquid Crystal Display
Product Specification
+12.0V
LVDS
2Port
CN1
(51pin)
MEM
CTRL
SDRAM
RGB
SCL
Timing Controller
(LVDS Rx integrated)
EEPROM
SDA
Mini-LVDS(RGB)
G1
Gate Driver Circuit
Source Driver Circuit
S1S1920
TFT - LCD Panel
AI_Enable
VBR_OUT
Power Circuit
G1080
Block
VBR for AI
+24.0V
GND
Status
12Pin X 1CN
2Pin X 1CN
General Features
Active Screen Size46.96 inch (1192.78mm) diagonal
Outline Dimension1096.0(H) x 640.0 (V) x 48.1 mm(D) (Typ.)
Pixel Pitch0.5415 mm x 0.5415 mm
Pixel Format1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Power ConsumptionTotal 232 W (Typ.) (Logic=12W, Inverter=220 W [IBL= 6mA] )
Weight20.0K g (Typ.)
Display ModeTransmissive mode, Normally black
Surface TreatmentHard coating(3H), Anti-glare treatment of the front polarizer
Ver. 0.1Mar. 16. 2005
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/ 27
www.panelook.com
Global LCD Panel Exchange Center
2. Absolute Maximum Ratings
The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.
Table 1. ABSOLUTE MAXIMUM RATINGS
www.panelook.com
LC470WU1
Liquid Crystal Display
Product Specification
Parameter
Unit
MinMax
Value
Power Input
Voltage
ON/OFF Control VoltageVON/OFF-0.3+5.25VDC
Brightness Control VoltageVBr0+3.3VDC
Operating TemperatureTOP0+40
Storage TemperatureTST-20+50
Operating Ambient HumidityHOP1090%RH
Storage HumidityHST1090%RH
LCM
Backlight inverterVBL21.6+27.0VDC
VLCDTBD+14.0VDC
¶C
¶C
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ¶C Max. and no condensation of water.
90%
60
60%
RemarkSymbol
GY\Gr YG¶j
Note 1
Wet Bulb
Temperature [
0
Ver. 0.1Mar. 16. 2005
¶C]
30
20
10
10203040506070800-20
Dry Bulb Temperature [
50
40
¶C]
40%
10%
Storage
Operation
Humidity [(%)RH]
5/ 27
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power for the LCD circuit. The other Is used for the CCFL
backlight and inverter circuit.
Table 2. ELECTRICAL CHARACTERISTICS
www.panelook.com
LC470WU1
Liquid Crystal Display
Product Specification
ParameterSymbol
UnitNote
MinTypMax
Value
Circuit :
Power Input VoltageVLCD11.412.012.6VDC
Power Input CurrentILCD
Power ConsumptionPLCD-1214Watt1
Rush currentIRUSH--5A3
Note : 1. The specified current and power consumption are under the V
condition whereas mosaic pattern(8 x 6) is displayed and f
-TBDTBDmA1
-TBDTBDmA2
=12.0V, 25 r 2¶C, fV=60Hz
LCD
is the frame frequency.
V
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 1ms (min.).
White : 255Gray
Black : 0Gray
Mosaic Pattern(8 x 6)
Ver. 0.1Mar. 16. 2005
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6/ 27
www.panelook.com
Global LCD Panel Exchange Center
Table 2. ELECTRICAL CHARACTERISTICS (Continue)
www.panelook.com
LC470WU1
Liquid Crystal Display
Product Specification
ParameterSymbol
UnitNote
MinTypMax
Inverter :
Value
Power Input VoltageVBL22.824.025.2VDC
Power Supply Input Voltage Ripple
Power Input CurrentI
Power ConsumptionP
Input Voltage for
Control System
Signals
Brightness AdjustV
OnV on4.05.0V
On/Off
OffV off-0.30.00.5V
BLTBDTBDTBDA
BLTBD220250W
BR03.3VDC2
-0.20.2Vp-p
DC
DC
Lamp :
Life Time
50,000Hrs3
Notes :
1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 120
minutes at 25·2¶C
The specified current and power consumption are under the typical supply Input voltage, it is total power
consumption.
The ripple voltage of the power supply input voltage is under 0.2 Vp-p.
LPL recommend Input Voltage is 24.0V · 5%.
Brightness Control.
2.
This V
BR Voltage control brightness.
1
VBR Voltage Function
3.3VMaximum Brightness (100%)
0VMinimum Brightness.(Burst On Duty 25%)
3. The life is determined as the time at which luminance of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25 r 2¶C.
Specified value is when lamp is aligned horizontally.
Ver. 0.1Mar. 16. 2005
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7/ 27
www.panelook.com
Global LCD Panel Exchange Center
3-2. Interface Connections
This LCD module employs two kinds of interface connection, a 51-pin connector is used for the module
electronics and two 12-pin connectors are used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector(CN1): FI-R51S-HF(manufactured by JAE) or equivalent