LG Motorsports Slick Sand Primer Info User Manual
Feature/Advantage
Benefit
High solids, high build formula
Easily fills pinholes, crazed
surfaces, gravel chips and other
surface imperfections in one coat
Easy sanding
Improves cycle time
Accepts all automotive and
industrial topcoats
Requires no sealer, improving
cycle time
PRODUCT: SLICK SAND™ Polyester Primer Surfacer
PART
NUMBER: 100708 Quart 6 units/case 21 lbs/case
100709 Gallon 4 units/case 50 lbs/case
DESCRIPTION: Slick Sand is a high solids, high build polyester primer surfacer ideally
suited for filling most rough and uneven surfaces in one coat. It has
excellent adhesion to fiberglass, SMC, body filler and wood surfaces.
Slick Sand is VOC complaint and provides an excellent foundation for any
paint system.
FEATURES
& BENEFITS:
SUBSTRATES:
Fiberglass
SMC
Rigid Plastics
Body Filler or Putty
Epoxy Primer
Self-Etch Primer (extends dry-to-sand time)
NOTE: All bare metal areas larger than one inch in diameter must be
treated with a high quality self-etch or epoxy primer.
CLEANING:
Surface must be clean and free of dirt, oil, grease and wax
To solvent clean raw, exposed fiberglass, it is recommended to clean
exposed area with acetone.
PREPARATION: Untreated Steel, Galvanized Steel and Bare Aluminum
All bare metals must be treated with a high quality self-etch or epoxy primer
prior to the application of Slick Sand
Follow paint company’s recommendations for surface prep and recoat of self-
etch or epoxy primer
a division of Illinois Tool Works Inc. | 6600 Cornell Road | Cincinnati, OH 45242 | (513) 489-7600
Made and Printed in the U.S. | ©2009 Evercoat
evercoat.com
Appearance
Gray liquid
VOC
Packaged: 2.54 lbs/gal (305 g/L)
Applied: 1.72 lbs/gal (206 g/L)
Dry-Film-Thickness (DFT)
4.0 – 6.0 mils per coat
Solids by Volume
57-62%
Solids by Weight
71-74%
Viscosity (Ready to Spray)
30-35 seconds in Zahn #3
Coverage at 1 mil 100% Transfer
1200 sq. ft. per U.S. gallon
PREPARATION: Pre-Painted Surfaces
Sand repair area and featheredge using 180 grit, 220 grit and finish with 320
grit sandpaper on a random orbital sander
Final clean with a quality wax and grease remover to remove sanding
residue prior to applying Slick Sand
Body Filler or Putty
Finish sanding body filler or putty with 180-220 grit sandpaper
Featheredge with 320 grit sandpaper
Blow off the surface with an air blow gun
MIXING:
Shake and stir thoroughly before mixing
Add one tube (.75 fl. oz.) liquid hardener to one quart of Feather Fill or 2% by
weight and mix thoroughly
Pot Life is 45 minutes @ 75°F (24°C)
Do not leave product in the spray gun for longer than 30 minutes
APPLICATION:
Use a primer gun with a 2.0 or larger fluid nozzle/air cap (Spray at paint gun
manufacturer’s recommended air pressure)
Apply 2-3 medium wet coats allowing 10-15 minutes flash time between
coats
FINISH:
Slick Sand will be ready to sand in about 2 hours depending on film build
Applying over self-etch primer could add 4-6 hours to the dry time
Once dry, sand Slick Sand with 400-600 grit sandpaper prior to next step
TECHNICAL
SPECIFICATIONS:
SAFETY &
HANDLING:
a division of Illinois Tool Works Inc. | 6600 Cornell Road | Cincinnati, OH 45242 | (513) 489-7600
IMPORTANT: The contents of these packages must be mixed with other components before the
products can be used. Before opening the packages, be sure to understand the warnings on all
labels of all components since the resulting product will have the warnings and cautions of all its
parts. Improper spray technique may result in hazardous conditions. Follow the spray
equipment manufacturer's instructions to prevent injury or fire. Follow respirator manufacturer's
directions for respirator use. Always wear eye and skin protection. Observe all precautions.
Consult MSDS for further safety information and/or handling instructions. In case of emergency,
contact your local emergency room or poison control center immediately. For professional use
only. Material Safety Data Sheets can be found online @ evercoat.com.
Made and Printed in the U.S. | ©2009 Evercoat
evercoat.com
Loading...