LG Electronics USA L1960TQ Users Manual

Test Report No.: GETEC-E3-07-018

FCC Class B Class II Permissive Change

APPENDIX H

: USER’S MANUAL

EUT Type: 19” LCD Monitor

FCC ID: BEJL1960TQ

Make sure to read the Important Precautions before using the product.

Keep the User's Guide(CD) in an accessible place for furture reference.

See the label attached on the product and give the information to your

dealer when you ask for service.

L1760TQ L1960TQ

User’s Guide

This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential eletrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation.

Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.

Do not Open the Display.

There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period of time. Never leave the display ON when leaving the house. Keep children from dropping or pushing objects into the display's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this display. During a lightning storm or when the display is to be left unattended for an extended period of time, unplug it from the wall outlet.

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc. Place the display in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen. However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel.

On Cleaning

Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of your local authority.

Connecting the Display

Important

This illustration depicts the general model of connection. Your product may differ from the items shown in the picture.

Once you connect the stand base, try not to disconnect it.

Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.

Before setting up the product, ensure that the power to the product, the computer system, and other attached devices is turned off.

Attaching/Separating the stand base

1. Place the product with its front facing downwardon a soft cloth.

2. Make sure the stand base directs to the sorrect direction(Front, Rear) and turn the

locking device at the bottom to OPEN to assemble the unit. After assembling the unit, turn the locking device to LOCK before use.

Turn the locking device to OPEN to separate the stand base.

3. Once assembled take the product up carefully and face the front side

4. After connecting the cable, adjust the angle of the panel for easy use.

(To connect the cable, see page A5 for reference.)

Tilt Range : -5˚~20˚

Ergonomic

It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the product should not exceed 5 degrees.

-5°

20°

Connecting the Display

To attach or separate the back cap

1. To attach the back cap, fix into the 3 holes first then slide it up to fit to the upper

groove.

2. To separate the back cap, hold the bottom part and pull it out.

Kensington Security Slot- optional Connected to a locking cable that can be purchased separately at most computer stores

NOTE

- Cover the back cap after connecting the cables before use.

(To connect the cable, see page A5 for reference.)

DVI-D DC-IN D-SUB

Connecting the Display

Connecting with the PC

1. Before setting up the product, ensure that the power to the product, the computer

system, and other attached devices is turned off.

2. Connect the signal cable . When attached, tighten the thumbscrews to secure the

connection.

3. Connect the power cable with the AC-DC adapter (AC-DC power supply) , and then

plug the cable in the outlet.

Wall-outlet type

PC-outlet type

DVI-D(This feature is not available in all countries.)

Mac adapter

For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector.

4. Touch the pawer button in front to turn on the product.

The 'Self Image Setting Function' will automatically run when the product is on. (Only Analog Mode)

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user

connects the product for the first time, this function automatically adjusts the display to optimal settings for individual input signals. If you want to adjust the product while in use, or wish to manually run this function once again, push the ‘SET/AUTO’ button on the front panel of the product. Otherwise, you may execute the ‘ Factory reset’ option on the OSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.

NOTE

This is a simplified representation

of the rear view. This rear view represents a general model; your display may differ from the view as shown.

MAC

[ Arranging the cables]

[ Connecting the cables]

DVI-D DC-IN D-SUB

Control Panel Functions

MENU Button

Use this button to enter or exit the On Screen Display.

Control Function

OSD LOCKED/UNLOCKED

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message

"OSD UNLOCKED" should appear.

+ -

Buttons

Use these buttons to select or adjust functions in the On Screen Display.

For more information, refer to page A13.

Use this button to make D-Sub or DVI connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub.

Button

(SOURCE Hot key)

Front Panel Controls

Side

SOURCESOURCE

MENUME

SET/AUTOSET/AUTO

EngineEngine

Button

( )

Control Panel Functions

This Indicator lights up green or blue when the display operates normally(On Mode). If the display is in Sleep Mode (Energy Saving), this indicator color changes to amber.

Touching on the button for several seconds will power up the unit and touching on it again for several seconds will power off.

Power Button

Power Indicator

Use this button to enter a selection in the On Screen Display.

SET/AUTO Button

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press the SET/AUTO button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).

The best display mode is 17 inch product : 1280 x 1024

19 inch product : 1280 x 1024

Control Function

On Screen Display (OSD) Control Adjustment

Screen Adjustment

Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.

To make adjustments in the On Screen Display, follow these steps:

Press the MENU Button, then the main menu of the OSD appears.

To access a control, use the - or + Buttons. When the icon you want becomes highlighted, press the SET/AUTO Button.

Use the - / + Buttons to adjust the image to the desired level. Use the

SET/AUTO Button to select other sub-menu items.

Push the MENU Buttononce to return to the main menu to select another function. Push the MENU Buttontwice to exit from the OSD.

NOTE

Allow the display to stabilize for at least 30 minutes before making image adjustments.

SET/AUTO

MENU MENU

NOTE

The order of icons may differ depending on the model (A9~A13).

On Screen Display(OSD) Selection and Adjustment

The following table indicates all the On Screen Display control, adjustment, and setting menus.

To adjust the brightness, contrast and gamma of the screen

PICTURE

COLOR

POSITION

TRACKING

SETUP

Main menu Sub-menu A D Reference

PRESET

RED

GREEN

BLUE

To adjust the position of the screen

To customize the color of the screen

To customize the screen status for a user's operating environment

To improve the clarity and stability, sharpness of the screen

BRIGHTNESS

CONTRAST

GAMMA

HORIZONTAL

VERTICAL

CLOCK

PHASE

SHARPNESS

WHITE BALANCE

POWER INDICATOR

FACTORY RESET

LANGUAGE

OSD

HORIZONTAL

POSITION VERTICAL

6500K 9300K

: Adjustable A : Analog Input D : Digital Input

To select or customize desired image settings

FLATRON

F-ENGINE

MOVIE / TEXT

USER

NORMAL

+ 23 hidden pages