LG Electronics USA G4010 Users Manual

G4010

User Guide

Unpacking 8 For Your Safety

Your Phone

Phone Components 14 Your Phone's Features

15 Display Information

Getting Started 18

Using the Battery, Charger and SIM Card

Installing the Battery

18 Removing the Battery

19 Charging the Battery

19 Disconnecting the Charger

20 Installing the SIM Card

Turning Your Phone On and Off 22

Turing Your Phone On

22 Turning Your Phone Off

Access Codes

PIN code

22 PIN2 code

23 PUK code

23 PUK2 code

23 Security code

Barring Password

General Functions 24

Making and Answering Calls

Making a Call

Making a Call by Send key

Making International Calls

Ending a Call

24 Making a Call From the Phonebook

25 Adjusting the Volume

25 Answering a Call

25 Signal Strength

26 Manner Mode

26 Entering Text

Phonebook

30 In-Call Menu

During a Call

31 Making a Second Call

31 Swapping Between Two Calls

31 Answering an Incoming Call

31 Rejecting an Incoming Call

32 Muting the Microphone

32 Switching DTMF Tones on During a Call

Multiparty or Conference Calls 32

Making a Second Call

33 Setting Up a Conference Call

Putting a Conference Call on Hold

33 Activate the Conference Call on Hold

33 Adding Calls to the Conference Call

33 Displaying Callers in a Conference Call

33 Private Call in a Conference Call

33 Ending a Conference Call

Menu Tree 35 Selecting Functions and Options

38 Messages

Text Messages 39

Write Message

39 Inbox

40 Outbox

41 Draft

41 Settings

42 Delete

Voice Messages

Listen to Voice Messages

43 Voice Mailbox Number

Info Service

Receive

44 Inbox

Topics 44 Alert

Auto Display

Language

Templates

Name Card

Check Memory

Call Register 47

Missed Calls 47 Received Calls

Dialed Calls

Delete Recent Calls

Call Durations

Last Call

Received Calls

Dialed Calls

All Calls

Call Costs

Last Call’s Cost

All Calls’ Cost

Cost Settings

Call Cost’s Limit

Set Tariff

Auto Display

Table of Contents

GPRS Information 51

WAP Information

External Device

Total Data

Profiles 52 Settings

Alarm Clock 54 Date & Time Settings

Date & Time

55 Auto Update

Phone Settings

Display Settings

56 Language

56 LED indicator

Call Settings

Call Divert

57 Answer Mode

58 Send My Number

58 Call Waiting

58 Minute Minder

59 Auto Redial

59 Closed User Group

59 Select Line

Security Settings

PIN Code Request

Call Barring Service

Fixed Dial Number

Change Codes

Network Settings

Automatic

Manual

Preferred

GPRS Settings

External Device

Reset Settings

Organizer 65

Schedule 65 Memo

Phonebook

Add New

Speed Dials

Caller Groups

Copy All

Delete All

Settings

Information

Fun & Tools 73

Game 73

My Folder

Pictures

Animation

Sound

Unit Converter

Calculator

World time

Internet 77

Home 78 Push Message

Inbox

Receive

Profiles

Cache Settings

Clear Cache

Cache Check

WAP Information

Reset Profiles

Q & A 82 Accessories

Safety Guidelines

Glossary

101

Index

104

Important Information

This user guide contains important information on the use and operation of this phone. Please read all the information carefully for optimal performance and to prevent any damage to, or misuse of, the phone. Any changes or modifications not expressly approved in this user guide could void your warranty for this equipment.

Before You Start

Safety Instructions

WARNING! To reduce the possibility of electric shock, do not

expose your phone to high humidity areas, such as the bathroom, swimming pool, etc.

Always store your phone away from heat. Never store your phone in settings that may expose it to temperatures less than 32°F or greater than 104°F, such as outside during a snowstorm or

in your car on a hot day. Exposure to excessive cold or heat will result in malfunction, damage and/or catastrophic failure.

Be careful when using your phone near other electronic devices. RF emissions from your mobile phone may

affect nearby inadequately shielded electronic equipment. You should consult with manufacturers of any personal medical devices such as pacemakers and hearing aides to determine if they are susceptible to interference from your mobile phone. Turn off your phone in a medical facility or at a gas station. Never place your phone in a microwave oven as this will cause the battery to explode.

IMPORTANT! Please read the TIA SAFETY INFORMATION on page 87 before using your phone.

Unpacking For Your Safety

Check to make sure that you have all the parts shown below

Handset Standard

Battery

User GuideTravel Adapter

Safety Information

Please read and observe the following information for the safe and proper use of your phone and to prevent any unanticipated damage. Also, keep the user’s manual in an accessible place at all times after reading it.

▶ Unplug the power cord and charger during a lightning storm to

avoid electric shock or fire.

▶ Do not use your phone in high explosive areas as the phone

may generate sparks.

▶ Do not put your phone in a place subject to excessive dust, and

keep the minimum required distance between the power cord and heat sources.

▶ Unplug the power cord prior to cleaning your phone, and clean

the power plug pin when it is dirty.

▶ Do not damage the power cord by bending, twisting, pulling, or

subjecting it to heat. Do not use the plug if it is loose as it may cause fire or electric shock.

▶ Hold the power cord plug firmly to plug and unplug the power

cord. Ensure the plug is firmly connected. If it is not firmly connected, it may cause excessive heat or fire.

▶ Do not place a heavy item on the power cord. Do not allow the

power cord to be crimped as it may cause fire or electric shock.

▶ Be careful not to let the battery contact metal conductors such

as a necklace or coins. When shorted, it may cause an explosion.

▶ Do not disassemble or impact the battery as it may cause

electric shock, short-circuit, and fire. Store the battery in a place out of reach of children.

▶ Using a damaged battery or placing a battery in your mouth may

cause serious injury.

▶ Do not place items containing magnetic components such as a

credit card, phone card, bank book or a subway ticket, near your phone. The magnetic strip can be damaged by the phone.

▶ Do not hold or let the antenna come in contact with your body

during a call.

▶ Talking on your phone for a long period of time may reduce the

call quality due to heat generated during the use of the phone.

▶ Do not allow excessive vibration or impact to the phone. ▶ When you do not plan to use the phone for a long period of time,

store it in a safe area with the power cord unplugged.

FCC RF Exposure Information

WARNING! Read this information before operating the phone.

In August 1996, the Federal Communications (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.

The design of this phone complies with the FCC guidelines and these international standards.

For Your SafetyFor Your Safety

CAUTION

Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with skin, a minor burn may result. Contact your local dealer for a replacement antenna.

Body-worn Operation

This device was tested for typical body-worn operations with the back of the phone kept 0.59 inches (1.5 cm) from the body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.59 inches (1.5 cm) must be maintained between the user’s body and the back of the phone. Third-party belt-clips, holsters, and similar accessories containing metallic components should not be used. Body-worn accessories that cannot maintain

0.59 inches (1.5 cm) separation distance between the user’s body and the back of the phone, and have not been tested for typical bodyworn operations may not comply with FCC RF exposure limits and should be avoided.

Vehicle Mounted External Antenna (optional, if available)

A minimum separation distance of 8 inches (20 cm) must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements.

For more information about RF exposure, visit the FCC website at www.fcc.gov

FCC Part 15 Class B Compliance

This device and its accessories comply with part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device and its accessories may not cause harmful interference, and (2) this device and its accessories must accept any interference received, including interference that may cause undesired operation.

Cautions for Battery

▶ Do not disassemble. ▶ Do not short-circuit. ▶ Do not expose to high temperature: 60℃ (140℉). ▶ Do not incinerate.

Battery Disposal

▶ Please dispose of your battery properly or bring to your local

wireless carrier for recycling.

▶ Do not dispose in fire or with hazardous or flammable materials.

Adapter (Charger) Cautions

▶ Using the wrong battery charger could damage your phone and

void your warranty.

▶ The adapter or battery charger is intended for indoor use only.

Do not expose the adapter or battery charger to direct sunlight or use it in places with high humidity, such as the bathroom.

For Your SafetyFor Your Safety

Your Phone

Your Phone’’s Features

1. Earpiece 2,12. Left soft key / Right soft key: Each of these keys

perform the functions indicated by the text on the display immediately above them.

3. Side keys: These keys are used to control the volume of key tone in standby mode and speaker volume during a call.

4. Vibration key: Use to set the Manner Mode by pressing and holding the left navigation key for about 3 seconds while in standby mode.

5. Send key: You can dial a phone number and answer incoming calls. Press this key in standby mode to quickly access the most recent incoming, outgoing and missed calls.

6. Alphanumeric keys: These keys are used to dial a number in standby mode and to enter number or characters in edit mode.

7. Microphone: Can be muted during a call for privacy.

8. Active flip: Open the flip to answer an incoming call and close

to end the call.

9. Display screen: Displays phone status icons, menu items, Web information, pictures and more in full color.

10. Navigation key: Use for quick access to phone functions.

11. Confirmation key: Long press will launch the WAP browser.

Allows you to select and confirm menu options.

13. Message key: Use to retrieve or send voice and text

messages.

14. End/Power key: Allows you to power the phone on or off,

end calls, or return to Standby Mode.

Phone Components

1. Earpiece

8. Active flip

9. Display screen

10. Navigation key

2. Left soft key

3. Side keys

5. Send key

11. Confirmation key

12. Right soft key

4. Vibration key

13. Massage key

14. End / Power key

7. Microphone

6. Alpha numeric keys

Your Phone Your Phone

SIM Card Socket

Battery Lock

Antenna

Cable Connector/ Battery Charging Connector

Handstrap Hole

Battery

Battery Terminals

Icon Description

Indicates the strength of the network signal. Indicates a call is in progress. Indicates that you are roaming off the network. Indicates that GPRS service is available. Indicates the alarm has been set and is on. Indicates the status of the battery charge. Indicates the receipt of a text message. Indicates the receipt of a voice message. Indicates that the vibration ringer has been set. Indicates the receipt of an e-mail message. Indicates the Loud menu in Profiles. Indicates the Quiet menu in Profiles. Indicates the Headset menu in Profiles. Indicates the Car menu in Profiles. Indicates the General menu in Profiles. Indicates that you can use the push message service. Indicates the Schedule function.

Display Information

The table below describes various display indicators or icons that appear on the phone’s display screen.

On-Screen Icons

Getting Started

Using the Battery, Charger and SIM Card

Installing and Removing the Battery

▶ To install, insert the battery into the opening on the back of the

phone and gently press down until the latch snaps into place.

▶ To remove, first make sure the power is off. Press the battery

release latch up and remove the battery from the phone at a 45degree angle.

Installing the Battery

To install the battery, insert the bottom of the battery into the opening on the back of the phone. Then push the battery down until the latch clicks.

Removing the Battery

Turn the power off. (If power is left on, there is a chance you could lose the stored telephone numbers and messages.)

Pressing the release latch upwards will detach the battery from the phone.

Warning Do not force the connector as this may damage the

phone and/or the travel adapter.

Charging the Battery

Use of unauthorized accessories could damage your phone and invalidate your warranty. To use the travel adapter provided with your phone:

1. With the battery in position on the phone, connect the lead from the travel adapter to the bottom of the phone. Check that the arrow on the lead connector is facing towards the front of the phone.

2. Connect the adapter to a standard AC wall outlet. Only use the travel adapter that comes included with the package.

Getting StartedGetting Started

Disconnecting the charger

When charging is finished, disconnect the adapter from the power outlet and from the phone by pressing on the gray tabs on both sides of the connector while pulling the connector out.

Installing the SIM Card

When you subscribe to a cellular network, you are provided with a plug-in SIM card loaded with your subscription details (PIN, optional services available and so on). Locate the SIM card socket in the back of the phone. Follow the steps below to install the SIM card.

1. Remove the battery if attached.

2. Slide the SIM card into the SIM card holder so that the holder

locks the card in position.

Notice When you need to remove the SIM card, slide it towards

the top of the phone and take it out of the holder.

Notice

▶ Before installing always make sure that the phone is switched off

and remove the battery.

▶ The metal contact of the SIM card can be easily damaged by

scratches. Pay special attention to the SIM card while handling and installing. Follow the instructions supplied with the SIM card.

Notice

▶ The battery delivered with your phone has to be fully charged

before using it.

▶ Do not remove the battery or the SIM card while charging. ▶ If your phone is powered on while charging, you’ll see the bars in

the battery indicator icon cycle. When the battery is fully charged, the bars in the battery indicator icon will flash on and off

▶ If your phone is powered off, the display will show the charging

status. “Charging” or “Full” will be displayed.

If the battery fails to charge completely:

▶ After turning the phone on and off, please attempt to recharge the

battery.

▶ After detaching and reattaching the battery, please attempt to

recharge the battery.

FUll

Charging

SIM

Getting StartedGetting Started

Turning Your Phone On and Off

Turning Your Phone On

1. Install a charged battery pack or connect the phone to an

external power source such as the vehicle power adapter or car kit.

2. Press for more than five seconds.

3. Depending on the status of the PIN code Request setting you

may or may not need to enter it.

Turning Your Phone Off

1. Press for a few seconds.

Notice

Like any other radio device, avoid any unnecessary contact with the antenna while your phone is on.

Access Codes

You can use the access codes described in this section to avoid unauthorized use of your phone. The access codes (except PUK and PUK2 codes) can be changed by using the Change codes feature [Menu 4-5-4].

PIN code (4 to 8 digits)

The PIN (Personal Identification Number) code protects your SIM card against unauthorized use. The PIN code is usually supplied with the SIM card. When the PIN Code Request is set to Enable, your phone will request the PIN code every time it is switched on. When the PIN Code Request is set to Disable, your phone connects to the network directly without the PIN code.

PIN2 code (4 to 8 digits)

The PIN2 code, supplied with some SIM cards, is required to access functions such as Advice of Call Charge and Fixed Dial Number. These functions are only available if supported by your SIM card.

PUK code (4 to 8 digits)

The PUK (PIN Unblocking Key) code is required to change a blocked PIN code. The PUK code may be supplied with the SIM card. If not, contact your local service provider for the code. If you lose the code, contact your service provider.

PUK2 code (4 to 8 digits)

The PUK2 code, supplied with some SIM cards, is required to change a blocked PIN2 code. If you lose the code, contact your service provider.

Security code (4 to 8 digits)

The security code protects the unauthorized use of your phone. The default security code is set to “0000” and the security code is required to delete all phone entries and to activate the Restore Factory Settings menu. The security code default setting can be modified from the Security Settings menu.

Barring Password

The barring password is required when you use the Call Barring function. The password is obtained from the service provider when you subscribe to this function. See page 65 for further details.

Making and Answering Calls

Making a Call

1. Make sure your phone is powered on.

2. Enter a phone number including the area code. To edit a

number on the display screen, press the right/left navigation keys to move the cursor to desired position or simply press the right/left navigation keys to erase one digit at a time.

▶

Press and hold the right soft key[Clear] to erase the entire number.

3. Press to call the number.

4. When finished, press .

Making a Call by Send Key

1. Press , and the most recent incoming, outgoing and missed

phone numbers will be displayed.

2. Select the desired number by using the navigation key.

3. Press .

Making International Calls

1. Press and hold the key for the international prefix. The “+”

character can be replaced with the international access code.

2. Enter the country code, area code, and the phone number.

3. Press .

Ending a Call

When you have finished a call, press the key.

Making a Call From the Phonebook

You can store names and phone numbers dialed frequently in the SIM card as well as the phone memory known as the Phonebook.

You can dial a number by simply looking up a name in the phonebook. For more details on the Phonebook feature, please refer to page 68.

Adjusting the Volume

During a call, if you want to adjust the earpiece volume, use the side keys of the phone. In idle mode with the flip cover open, you can adjust the key volume using the side keys.

Answering a Call

When you receive a call, the phone rings and the flashing phone icon appears on the screen. If the caller can be identified, the caller’s phone number(or name if stored in your phonebook) is displayed.

1. Open the flip and press the key or the left soft key to answer an incoming call. If the Any key menu option(Menu 4.4.2) has been set to , any key press will answer a call except for the

key or the right soft key.

2. End the call by closing the phone or pressing the key.

General Functions

Notice

▶ To reject an incoming call, press and hold the side keys on the left

side of the phone without opening the flip.

▶ If the Flip open menu option(Menu 4.4.2) is set to , you do not

need to press any key. You can answer the call simply by opening the flip.

Notice You can answer a call while using the phonebook or other

menu features.

Manner Mode (Quick)

When the flip is closed, Manner Mode can be activated by pressing and hold down Side keys.

Signal Strength

Since the antenna is fixed, it does not extend. If you are inside a building, being near a window may give you better reception. You can see the strength of your signal by the signal indicator ( ) on your phone’s display screen.

Entering Text

You can enter alphanumeric characters by using the phone’s keypad. For example, storing names in the phonebook, writing a message, creating a personal greeting or scheduling events in the calendar all require entering text.

Following text input methods are available in the phone.

T9 Mode

This mode allows you to enter words with only one keystroke per letter. Each key on the keypad has more than one letter. The T9 mode automatically compares your keystrokes with an internal linguistic dictionary to determine the correct word, thus requiring far fewer keystrokes than the traditional ABC mode.

ABC Mode

This mode allows you to enter letters by pressing the key labeled with the required letter once, twice, three or four times until the letter is displayed.

123 Mode (Numbers Mode)

Type numbers using one keystroke per number. To change to 123 mode in a text entry field, press key until 123 mode is displayed.

Symbolic Mode

This mode allows you to enter special characters.

Changing the Text Input Mode

1. When you are in a field that allows characters to be entered, you

will notice the text input mode indicator in the upper right corner of the display.

2. If you want to change modes, press the key. The available modes are displayed.

Using the T9 Mode

The T9 predictive text input mode allows you to enter words easily with a minimum number of key presses. As you press each key, the phone begins to display the characters that it thinks you are typing based on a built-in dictionary. As new letters are added, the word changes to reflect the most likely candidate from the dictionary.

1. When you are in the T9 predictive text input mode, start entering a word by pressing keys to . Press one key per letter.

▶ The word changes as letters are typed - ignore what's on the

screen until the word is typed completely.

▶ If the word is still incorrect after typing completely, press the

down navigation key once or more to cycle through the other word options.

General FunctionsGeneral Functions

Write message

918

Options Back

En T9

Notice You can select a different T9 language from the menu option.

The default setting on the phone is T9 enabled mode. To turn it off, select the T9 Off option from the menu.

Example: Press to type Good

Press [down navigation key] to type

Home

▶ If the desired word is missing from the word choices list, add it

by using the ABC mode.

2. Enter the whole word before editing or deleting any keystrokes.

3. Complete each word with a space by pressing the key.

To delete letters, press right soft key[Clear]. Press and hold down right soft key[Clear] to erase entire words.

Using the ABC Mode

Use the to keys to enter your text.

1.Press the key labeled with the required letter:

▶ Once for the first letter ▶ Twice for the second letter ▶ And so on

2.To insert a space, press the key once. To delete letters, press the right soft key[Clear]. Press and hold down the right soft key[Clear] to clear the display.

Notice

To exit the text input mode without saving your input, press . The phone returns to the previous menu level.

Notice Refer to the table below for more information on the

characters available using the keys.

General FunctionsGeneral Functions

Characters in the Order Display

Upper Case Lower Case

. , - ¿? ¡ ! @1 . , - ¿? ¡ ! @1

A B C Á Ã Ç 2 a b c á ã ç 2

D E F É 3 d e f é 3

G H I Í 4 g h i í 4

J K L 5 j k l 5

M N O Ó Ñ 6 m n o ó ñ 6

P Q R S 7 p q r s 7

T U V Ú Ü 8 t u v ú ü 8

W X Y Z 9 w x y z 9

Space Key Space Key

Using the 123 (Numbers) Mode

The 123 Mode enables you to enter numbers in a text message (a telephone number, for example).

Press the keys corresponding to the required digits before manually switching back to the appropriate text entry mode.

Using the Symbol Mode

The Symbol Mode enables you to enter various symbols or special characters.

To enter a symbol, press the key. Use the navigation keys to select the desired symbol and press the [OK] key.

Key

Phonebook

You can store phone numbers and their corresponding names in the memory of your SIM card.

In addition, you can store up to 255 numbers and names in the phone memory.

The SIM card and phone memory, although physically separate, are utilized like a single entity known as the Phonebook. (See page 67 for details)

General FunctionsGeneral Functions

In-Call Menu

Your phone provides a number of control functions that you can use during a call. To access these functions during a call, press the left soft key [Options].

During a Call

The menu displayed on the handset screen during a call is different than the default main menu displayed when in idle screen, and the options are described below.

Making a Second Call

You can get a number you wish to dial from the phonebook to make a second call. Press the right soft key then select Search. To save the dialed number into the phonebook during a call, press the right soft key then select Add New.

Swapping Between Two Calls

To switch between two calls, press the left soft key, and then select Swap.

Answering an Incoming Call

To answer an incoming call when the handset is ringing, simply press the key. The handset is also able to warn you of an incoming call while you are already on a call. A tone sounds in the earpiece, and the display will show that a second call is waiting. This feature, known as Call Waiting, is only available if your network supports it. For details of how to activate and deactivate it see Call Waiting [Menu 4-4-4].

If Call Waiting is on, you can put the first call on hold and answer the second, by pressing or by pressing the left soft key, and then selecting the Hold & Answer. You can end the current call and answer the waiting call by pressing the left soft key and then selecting End & Answer.

Rejecting an Incoming Call

You can reject an incoming call without answering by simply pressing the key.

During a call, you can reject an incoming call by pressing the left soft key, which is the [Menu] key and selecting the

Conference/Reject or by pressing the key.

Muting the Microphone

You can mute the microphone during a call by pressing the [Menu] key then selecting Mute on. The handset can be unmuted by pressing the Mute off menu. When the handset is muted, the caller cannot hear you, but you can still hear them.

Switching DTMF Tones on During a Call

To turn DTMF tones on during a call, press the left soft key, and then select DTMF on. DTMF tones can be turned off the same way. DTMF tones allow your phone to make use of an automated switchboard.

Multiparty or Conference Calls

The multiparty or conference service provides you with the ability to have a simultaneous conversation with more than one caller, if your network service provider supports this feature. A multiparty call can only be set up when you have one active call and one call on hold, both calls having been answered. Once a multiparty call is set up, calls may be added, disconnected or separated (that is, removed from the multiparty call but still connected to you) by the person who set up the multiparty call. These options are all available from the In-Call menu. The maximum callers in a multiparty call are five. Once started, you are in control of the multiparty call, and only you can add calls to the multiparty call.

General FunctionsGeneral Functions

Making a Second Call

You can make a second call while currently on a call. Enter the second number and press the . When the second call is connected, the first call is automatically placed on hold. You can swap between calls, by selecting the left soft key and then selecting Swap.

Setting Up a Conference Call

To set up a conference call, place one call on hold and while the active call is on, press the left soft key and then select the Conference/Join all.

Putting a Conference Call on Hold

To put a conference call on hold, press the left soft key, and then select the Conference/Hold all.

Activate the Conference Call on Hold

To activate a conference call on hold, press the left soft key, and then select the Conference/Join all.

Adding Calls to the Conference Call

To add a call to an existing conference call, press the left soft key, and then select the Conference/Join all.

Displaying Callers in a Conference Call

To scroll through the numbers of the callers who make up a conference call on the handset screen, press the up/down navigation keys.

Private Call in a Conference Call

To have a private call with one caller from a conference call, display the number of the caller you wish to talk to on the screen, then press the left soft key. Select the Conference/Private to put all the other callers on hold.

1. Messages (see page 39)

1.1 Text messages

1.1.1 Write message

1.1.2 Inbox

1.1.3 Outbox

1.1.4 Draft

1.1.5 Settings

1.1.6 Delete

1.2 Voice messages

1.2.1 Listen to voice messages

1.2.2 Voice mailbox number

1.3 Info service

1.3.1 Receive

1.3.2 Inbox

1.3.3 Topics

1.3.4 Alert

1.3.5 Auto display

1.3.6 Languages

1.4 Templates

1.5 Name card

1.6 Check memory

2. Call Register (see page 47)

2.1 Missed calls

2.2 Received calls

2.3 Dialed calls

2.4 Delete recent calls

2.4.1 Missed calls

2.4.2 Received calls

2.4.3 Dialed calls

2.4.4 All calls

2.5 Call durations

2.5.1 Last call

2.5.2 Received calls

2.5.3 Dialed calls

2.5.4 All calls

2.6 Call costs

2.6.1 Last call’s cost

2.6.2 All calls’ cost

2.7 Cost settings

2.7.1 Call cost’s limit

2.7.2 Set tariff

2.7.3 Auto display

2.8 GPRS information

2.8.1 WAP information

2.8.2 External device

2.8.3 Total data

Menu Tree

The following illustration shows the available menu structure and indicates the:

▶ Number assigned to each menu option. ▶ Page where you can find the feature description.

Ending a Conference Call

Currently displayed caller from a conference call can be disconnected by pressing the key. To end a conference call, press the left soft key, and then select the Conference/End multiparty. Selecting the left soft key then Conference/End all, will end all the active and on-hold calls.

General Functions

Shown only if supported by CPHS(Common PCS Handset Specification)

+ 37 hidden pages