LG Electronics USA E2042SA User Manual
ENGLISH
OWNER'S MANUAL
LED LCD MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
LED LCD MONITOR MODEL
E1942S E2042T
E2042S E2242T
E2242S E2342T
E2442T
www.lg.com
Important Precautions
NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTRERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE
This epuipment has been tested and found to comply with the limits for a class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
A3
ENGLISH
2TABLE OF CONTENTS
CONTENTS
3ASSEMBLING AND PREPARING
3Unpacking
4Parts and buttons
6Setting up the Monitor set
6- Attaching the Stand
6- Detaching the Stand
7 - Mounting on a table
8- Mounting on a wall
10 USING THE MONITOR SET
10 Connecting to a PC
10 - D-SUB connection
10 - DVI-D connection
12 CUSTOMIZING SETTINGS
12Accessing The Main Menus
13Customizing Settings
13- Menu Settings
14-PICTURE
15-COLOR
16-DISPLAY
17-OTHERS
18SUPER ENERGY SAVING
19MODE Setting
20 TROUBLESHOOTING
22 SPECIFICATIONS
21E1942S
22E2042S
23E2042T 24 E2242S
25E2242T
26E2342T
27E2442T
28Preset Modes (Resolution)
29Indicator
ASSEMBLING AND PREPARING 3
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
ENGLISH
CD(Owner's Manual) / |
D-SUB Cable |
DVI-D Cable |
Card |
|
(Only E2042T/E2242T/E2342T/E2442T) |
|
|
(This cable is not included in all |
|
|
countries.) |
|
|
or |
Power Cord |
AC-DC Adapter |
AC-DC adapter |
(Depending on the country) |
(Depending on the country) |
|
Stand Body |
Stand Base |
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
Any damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE
The accessories supplied with your product may vary depending on the model.
Product specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
4ASSEMBLING AND PREPARING
Parts and buttons
ENGLISH
MENU / |
|
|
/ |
|
|
MODE / |
AUTO / |
|
|
INPUT / EXIT |
|
|
|
MENU /
/
MODE /
AUTO /
INPUT / EXIT
Power IndicatorLighting On: Turned onLighting Off: Turned off
(Power Button)
Button (See p.11)
DC-IN |
/ |
D-SUB |
/ |
DVI-D |
|
D-SUB |
|
|
DC-IN |
|
|
|
|
|
|
|
|
|
|
|
Connection panel (See p.9)
ASSEMBLING AND PREPARING 5
Setting up the Monitor set
Attaching the Stand
1Place the Monitor set with the screen side down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.
2 Attach the Stand body and then attach the Stand Base,then tighten the screw to the right with a Coin.
Detaching the Stand
1Place the Monitor set with the screen side down on a flat and cushioned surface.
2Turn the screw to the left with a Coin, and then pull out the Stand Base from the Stand Body, then pull out the Stand Body from the Monitor set .
Stand Body
3
2
Stand Body
Stand Base
2
Stand Base |
3 |
CAUTION |
|
This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.
ENGLISH
ENGLISH
6ASSEMBLING AND PREPARING
Mounting on a table |
3 Press (Power) button on the bottom switch |
|
panel to turn the power on. |
1Lift and tilt the Monitor set into its upright position on a table.
Leave a 10 cm (minimum) space from the wall for proper ventilation.
|
CAUTION |
10 cm |
Unplug the power cord before moving the |
|
Monitor to another location. Otherwise electric |
|
10 cm |
10 cm |
shock may occur. |
|
|
|
10 cm |
Using the cable holder
2 Connect the AC-DC Adapter and Power Cord to wall outlet.
Cable holder
or
/
DC-
IN
ASSEMBLING AND PREPARING 7
WARNING
Using the Kensington security system
When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.
Do not touch or press the screen when adjusting the angle of the monitor.
Do not hold this set like below picture. Monitor screen can detach from stand base and injure your body.
NOTE
Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.
5
20
The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www.kensington.com.
Connect the Kensington security system cable between the Monitor set and a table.
NOTE
The Kensington security system is optional. You can obtain it from most electronics stores.
ENGLISH
Front 
Rear
ENGLISH
8ASSEMBLING AND PREPARING
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
10 cm
10 cm
10 cm
10 cm
If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.
1Please, Use the screw and wall mount interface in accordance with VESA Standards.
2If you use screw longer than standard, the monitor might be damaged internally.
3If you use improper screw, the product might be damaged and drop from mounted position. In
this case, LG Electronics is not responsible for it.
4 VESA compatible.
5Please use VESA standard as below.
784.8 mm (30.9 inch) and under
* Wall Mount Pad Thickness : 2.6 mm * Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
* Please use VESA standard wall mount pad and screws.
|
|
|
|
|
|
|
|
Model |
|
E1942S |
E2042T |
|
|
E2442T |
|
|
E2042S |
E2242T |
|
|
|
|
|
|
|
|
|
|
|
||
|
|
E2242S |
E2342T |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VESA (A x B) |
|
75 x 75 |
|
|
|
100 x 100 |
|
Standard screw |
|
M4 |
|
|
|
|
|
Number of screws |
4 |
|
|
|
|
|
|
CAUTION
Disconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.
If you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.
Use only an authorized LG wall mount and contact the local dealer or qualified personnel.
Do not over tighten the screws as this may cause damage to the Monitor set and void your warranty.
Use only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.
NOTE
Use the screws that are listed on the VESA standard screw specifications.
The wall mount kit will include an installation manual and necessary parts.
The wall mount bracket is optional. You can obtain additional accessories from your local dealer.
The length of screws may differ depending on the wall mount. Be sure to use the proper length.
For more information, refer to the instructions supplied with the wall mount.
ASSEMBLING AND PREPARING 9
USING THE MONITOR SET
Connecting to a PC |
NOTE |
Your Monitor set supports Plug & Play*. *Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.
D-SUB connection
Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.
E1942S
E2042S
E2242S
DC-IN / |
D-SUB |
When using a D-Sub signal input cable connector for Macintosh
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.
ENGLISH
DVI-D connection
Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.
E2042T E2242T E2342T E2442T
RGB OUT
/
DC-IN
DC-IN / |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DVI-D |
|
|
|
D-SUB |
|
|
||||||||
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
E2042T
E2242T
E2342T
E2442T
Loading...