LG Electronics USA 50PC3DUUE User Manual

Download

Page 1

Introduction

Connection Options

(Model Name: 32/37/42LC2DU)

- This picture shown below may be somewhat different from your TV.

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

COMPONENT IN

AC IN

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

COMPONENT IN

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1AV IN 1

AV OUTAV OUT

ANTENNA/

CABLE IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

COMPONENT INCOMPONENT IN

DIGITAL AUDIO

OUT

PTICAL

SERVICE

1(DVI)

S-VIDEO Input

Provides better picture quality than the video input.

VIDEO Input

Connects the video signal from a video device.

AUDIO Input

Connections are available for listening to stereo sound from an external device.

COMPONENT IN

Connect a component video/audio device to these jacks.

AV OUT

Connect a second TV or monitor.

AV (Audio/Video) IN 1

Connect audio/video output from an external device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

ANTENNA/CABLE IN

Connect over-the air signals to this jack. Connect cable signals to this jack.

DIGITAL AUDIO OUT

Connect digital audio from various types of equipment.

Note: In standby mode, these ports do not work.

HDMI IN

Connect a HDMI signal. Or DVI (VIDEO)signal to the this port with a

HDMI to DVI cable.

RGB IN (PC)

Connect the monitor output from a PC to the appropriate input port.

Remote Control Port

Connect your wired remote control.

AUDIO IN (RGB/DVI)

Connect the monitor output from a PC to the appropriate input port.

RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC.

SERVICE

Power Cord Socket

For operation with AC power. Caution: Never attempt to operate the TV on DC power.

Page 2

Introduction

Remote Control Key Functions

POWER

Turns your TV or any other programmed equipment on or off, depending on mode.

VOL

POWER

1 2 3

4 5 6

7809

MUTE

FAV

IGHT +

VCR

DVD

ENTER

ADJUST

SAP

EZ SOUND

EZ PIC

FLASHBK

EXIT

TIME

ATIO

INFO

AUDIO

CABLE

STB

MODE

TV INPUT

INPUT

GHT -

TV INPUT

Rotates the input mode between Antenna and Cable. In AV12, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI, and HDMI2 input sources, screen returns to the last TV channel.

MODE

Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE, or STB. Select a mode other than TV, for the remote to operate an external device.

INPUT

External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC, HDMI1/DVI or HDMI2.

(AV 1-2, Component 1-2, RGB-PC , HDMI1/DVI or HDMI2 input sources are linked automatically, only if these are connected.)

EXIT

Clears all on-screen displays and returns to TV viewing from any menu.

TIMER

pp..4433

Lets you select the amount of time before your TV turns itself off automatically.

RATIO

pp..4455

Changes the aspect ratio.

Brings up the main menu to the screen.

BRIGHT + / -

- Adjust brightness on screen.

- It turns to the default settings brightness by changing mode source.

THUMBSTICK (Up/Down/Left/Right/ENTER)

Allows you to navigate the on-screen menus and adjust the system settings to your preference.

INFO (Refer to p.15) When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.

Page 3

Introduction

EZ PIC

pp..3333

Selects a factory preset picture mode depending on the viewing environment.

EZ SOUND

pp..3399

Selects the sound appropriate for the program's character.

SAP

Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode.

pp..4466 (*In DTV/CADTV modeGGpp..4466 )

Select a closed caption: Off, CC1~4, Text1~4.

ADJUST

Adjusts screen position, size, and phase in PC mode.

FAV

Use to scroll the Favorite channels.

MUTE

pp..2277

Switches the sound on or off.

CHANNEL UP/DOWN

Selects available channels found with EZ scan and Manual scan.

VOLUME UP/DOWN

Increases/decreases the sound level.

VOL

POWER

1 2 3

4 5 6

7809

MUTE

FAV

DAY -

GUIDE

Y+

RATIO

VCR

DVD

ENTER

APM

ADJUST

SAP

EZ SOUND

EZ PIC

FREEZE

FLASHBK

PAGE

EXIT

AUDIO

CABLE

STB

MODE

TV INPUT

INPUT

— (DASH)

Used to enter a program number for multiple program channels such as 2-1, 2-2,etc.

NUMBER BUTTONS

FLASHBK

Returns to the last channel viewed.

VCR/DVD/DVHS/Camcorder BUTTONS

Control some video cassette recorders or DVD players ("RECORD" button is not available for DVD player).

Page 4

Introduction

ATTACHING THE TV TO A WALL

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.

* If your product has the bolts in the eye-bolts position, loosen the bolts.

Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

42PC3DU/3DVU/50PC3DU/60PC1D

32/37/42LC2DU

■

Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -).

■

Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.

■

Close cover.

■

Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope.

■

Dispose of used batteries in a recycle bin to preserve environment.

TVTV

INPUT

DVD

ARC

EXIT

PIP PR +

PIP INPUT

SWAP

PIP PR -

SLEEP

LIST

I/II

TEXT PIP

SIZE

POSITION

VCR

POWER

TVTV

INPUT

DVD

ARC

EXIT

PIP PR +

PIP INPUT

SWAP

PIP PR -

Q.VIEW

SLEEP

LIST

I/II

TEXT PIP

SIZE

POSITION

VCR

POWER

TVTV

INPUT

DVD

ARC

EXIT

PIP PR +

PIP INPUT

SWAP

PIP PR -

Q.VIEW

SLEEP

LIST

I/II

TEXT PIP

SIZE

POSITION

VCR

POWER

/32/37/42LC2DU

42PC3DU/3DVU/50PC3DU 60PC1D

Installing Batteries

Remote control effective range

Page 5

Installation

For proper ventilation, allow a clearance of 4inches on each side from the wall.

Ensure adequate ventilation by following the clearance recommendations.

CAUTION

Power Supply

Short-circuit

Breaker

■

This picture shown below may be somewhat different from your TV.

GROUNDING

Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

DESKTOP PEDESTAL INSTALLATION

32/37/42LC2DU42PC3DU/3DVU/50PC3DU/60PC1D

4 inches

4 inches4 inches

4 inches

Page 6

Connect the cables as necessary. After connecting the cables neatly, arrange the cables to the Cable Holder.

To connect an additional equipment, see the External equip- ment Connections section.

Reinstall the CABLE MANAGE-

MENT as shown.

Bundle the cables using the supplied twister holder.

Basic Connection (For 32/37/42LC2DU)

32LC2DU

Cable holder

37/42LC2DU

32LC2DU

37/42LC2DU

32LC2DU

37/42LC2DU

Do not hold the CABLE MANAGEMENT when moving the product.

- If the product is dropped, you may be injured or the product may be broken.

How to remove the CABLE MANAGEMENT

- Hold the CABLE MANAGEMENT with both hands

and pull it upward.

CABLE MANAGEMENT

Page 7

Place the set with the screen facing down on a cushion or soft cloth as shown. Before unfolding the stand, please make sure two locks (A) on the bottom of the stand push outward.

Pull the stand out as shown. After unfolding the stand, please insert and tighten the screws (provided as parts of the product) in the holes (B) on the bottom of the stand.

When connecting cables to the set, Do not disengage the lock (C). This may cause the set to fall, causing serious bodily injury and serious damage to the set.

Basic Connection

(C)

Hold the CABLE MANAGEMENT with both hands and push it as shown.

Connect the cables as necessary. To connect an additional equipment, see the External equipment Connections section.

Reinstall the CABLE MANAGEMENT as shown.

* Image shown here may be slightly different from

your set.

When closing the stand for storage

- First remove the screws in the holes (B) on the bottom of the stand. And then pull two Hooks (D) of the stand bottom and fold the stand into the back of the set.

- After folding, push the two Locks (A) of the stand bottom outward.

(A)

(B)

(D)

(A)

(B)

How to use stand (For 42PC3DU/3DVU)

How to arrange the cable (For 50PC3DU)

For 60PC1D, 42PC3DU/3DVU

Arrange the cable as shown.

Page 8

Installation

Antenna Or Cable Connection

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Outdoor Antenna

Wall Antenna Socket

VHF Antenna

UHF Antenna

RF Coaxial Wire (75 ohm)

Turn clockwise to tighten.

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

Bronze Wire

Be careful not to bend the bronze wire when connecting the antenna.

Analog and Digital TV signals provided on antenna

- Antenna or Cable Service without a Cable Box Connection.

- For optimum picture quality, adjust antenna direction if needed.

Analog and DTV signals provided on two separate antennas

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

Bronze Wire

Turn clockwise to tighten.

Antenna

RF Coaxial Wire (75 ohm)

• In a poor signal area to improve picture quality, purchase and install a signal amplifier.

• If the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections.

• If the antenna is not installed properly, contact your dealer for assistance.

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

External Equipment Connections

signal amplifier

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

NOTE: All cables shown are not included with the TV

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

Turn clockwise to tighten.

Analog and Digital TV signals provided on cable

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

ANTENNA/

CABLE IN

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

Page 9

Installation

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

- Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

VCR Setup

When connecting with an antenna

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

ANTENNA/ANTENNA/

CABLE INCABLE IN

REMOTEREMOTE

CONTROL INCONTROL IN

RS-232C IN

(CONTROL(CONTROL & SER & SERVICE)VICE)

RGB INRGB IN

(PC)(PC)

AUDIO INAUDIO IN (RGB/DVI)(RGB/DVI)

SERVICESERVICE

HDMI IN HDMI IN

1(DVI)1(DVI)

When connecting with a RCA cable

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

HDMI / DVI IN

ANTENNA/

CABLE IN

REMOTE CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

AUDIO IN (RGB/DVI)

VIDEOVIDEO

AUDIOAUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1V IN 1

AV OUTV OUT

COMPONENTCOMPONENT IN

DIGITDIGITALAL AUDIO AUDIO

OUTOUT

OPTICALPTICAL

SERVICE

VCR

Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

Select AV 1 input source using the INPUT button on the remote control.

- If connected to AV IN2, select AV2 input source.

• If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the

set.

Connect the RF antenna out socket of the VCR to the Antenna socket on the set.

Connect the antenna cable to the RF antenna in socket of the VCR.

Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

VCR

Page 10

Installation

When connecting with an S-Video cable

VIDEOVIDEO

AUDIO

VIDEOVIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1V IN 1

AV OUTV OUT

COMPONENTCOMPONENT IN

DIGITDIGITALAL AUDIO AUDIO

OUT

OPTICALPTICAL

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

HDMI / DVI IN

ANTENNA/

CABLE IN

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

RGB IN

(PC)

AUDIO IN (RGB/DVI)

VIDEO

AUDIO

VIDEO

AUDIO

( )

S-VIDEO

AV IN 1

AV OUT

COMPONENT IN

DIGITAL AUDIO

OUT

OPTICAL

SERVICE

VCR

Connect the S-VIDEO output of the VCR to the SVIDEO input on the set. The picture quality is

improved; compared to normal composite (RCA cable) input.

Connect the audio outputs of the VCR to the AUDIO input jacks on the set.

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

Select AV1 input source with using the INPUT button on the remote control.

- If connected to AV IN2, select AV2 input source.

Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.

Camcorder

Video Game Set

Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

Select AV2 input source with using the INPUT button on the remote control.

- If connected to AV IN1 input, select AV1 input

source.

Operate the corresponding external equipment. Refer to external equipment operating guide.

External AV Source Setup

• This TV finds the connected input sources automatically for AV1, AV2, Component 1-2, RGB, HDMI1/DVI and HDMI2 sources are connected.

AUDIO VIDEO

Page 11

Installation

DVD Setup

When connecting with a S-Video cable

HDMI / DVI IN

ANTENNA/

CABLE IN

VIDEO

AUDIOAUDIO

VIDEO

AUDIOAUDIO

MONO

( )

S-VIDEOS-VIDEO

AV IN 1V IN 1

AV OUTV OUT

COMPONENTCOMPONENT IN IN

DIGITDIGITALAL AUDIO AUDIO

OUTOUT

OPTICAL

VIDEO

AUDIO

COMPONENT IN

S-VIDEO

(R) AUDIO (L)

DVD

Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set.

Connect the audio outputs of the DVD to the AUDIO input jacks on the set.

Turn on the DVD player, insert a DVD.

Select AV1 input source with using the INPUT button on the remote control.

- If connected to AV I N 2 , select AV 2 input source.

Refer to the DVD player's manual for operating instructions.

When connecting with a HDMI cable

Connect the HDMI output of the DVD to the HDMI IN 1(DVI) or 2 jack on the set.

Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control.

Refer to the DVD player's manual for operating instructions.

ANTENNA/

CABLE IN

HDMI-DVD OUTPUT

HDMI IN HDMI IN

1(DVI)1(DVI)

DVD

• TV can receive the video and audio signal simultaneously with using a HDMI cable.

• If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p.

• If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p.