Basic Connection
How to use stand (For 42PC3DU/3DVU)
1 Place the set with the screen facing down on a cushion or soft cloth as shown.
Before unfolding the stand, please make sure two locks (A) on the bottom of the stand push outward.
2 Pull the stand out as shown.
After unfolding the stand, please insert and tighten the screws (provided as parts of the product) in the holes (B) on the bottom of the stand.
(A)
3 When connecting cables to the set, Do not disengage the lock (C).
This may cause the set to fall, causing serious bodily injury and serious damage to the set.
(C)
(B)
*Image shown here may be slightly different from your set.
When closing the stand for storage
-First remove the screws in the holes (B) on the bottom of the stand. And then pull two Hooks (D) of the stand bottom and fold the stand into the back of the set.
-After folding, push the two Locks (A) of the stand bottom outward.
(A)
(B)
(D)
How to arrange the cable (For 50PC3DU)
1 |
Hold the CABLE MANAGEMENT with both |
2 |
Connect the cables as |
the |
|
hands and push it as shown. |
|
To connect an additional |
|
|
|
|
External equipment |
. |
3 |
Reinstall the CABLE |
For 60PC1D, 42PC3DU/3DVU |
shown |
Arrange the cable as shown. |
|
|
|
17
Installation
External Equipment Connections
NOTE: All cables shown are not included with the TV
Antenna Or Cable Connection
Analog and Digital TV signals provided on antenna
-Antenna or Cable Service without a Cable Box Connection.
-For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
Wall Antenna Socket
RF Coaxial Wire (75 ohm)
VHF Antenna
Turn clockwise to tighten.
UHF Antenna
Outdoor Antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
ANTENNA/
CABLE IN
Bronze Wire
Be careful not to bend the bronze wire when connecting the antenna.
Analog and Digital TV signals provided on cable
Cable TV Wall Jack
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
Analog and DTV signals provided on two separate antennas
Antenna |
Bronze Wire |
RF Coaxial Wire (75 ohm)
Turn clockwise to tighten.
Cable TV Wall Jack
RF Coaxial Wire (75 ohm)
Bronze Wire
ANTENNA/
CABLE IN
ANTENNA/
CABLE IN
• In a poor signal area to improve picture quality, purchase and install a sig-
ANTENNA/ |
signal |
OPTICAL |
|
|
CABLE IN |
|
|
|
|
|
amplifier |
DIGITAL AUDIO |
( |
) |
|
S-VIDEO VIDEO |
AUDIO |
||
|
|
|
OUT
1 IN AV OUT
two TV’s, install a “2-Way Signal Splitter”
properly, contact your dealer for assistance.
18
Installation
VCR Setup
-To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
-Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.
When connecting with an antenna
2 |
VCR |
1 Connect the RF antenna out socket of the VCR to |
|
the Antenna socket on the set. |
|||
|
S |
OUT |
|
OUTPUT |
(R) AUDIO (L) |
VIDEO |
|
|
|
|
IN |
|
1
SERVICE
RGB IN |
|
(PC) |
|
AUDIO IN |
REMOTE |
(RGB/DVI) |
CONTROL IN |
HDMI IN |
|
2 |
|
1(DVI)
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL & SERVICE)
2Connect the antenna cable to the RF antenna in socket of the VCR.
3Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
4Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
When connecting with a RCA cable
VCR
ANT IN
OUT |
S-VIDEO |
ANT OUT |
(R) AUDIO (L) |
VIDEO |
OUTPUT |
|
|
|
SWITCH |
|
IN |
|
3 |
4 |
|
|
1 |
|
|
|
C |
|
|
VIDEO |
UDIO |
|
|
|
INOMPONENT |
|
|
|
OUT AV |
|
OPTICAL |
|
IN AV |
|
DIGITAL AUDIO |
S-VIDEO VIDEO |
||
1 |
|||
OUT |
|
|
Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
3Select AV1 input source using the INPUT button on the remote control.
- If connected to AV IN2, select AV2 input source.
•If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set.
19
Installation
When connecting with an S-Video cable
VCR
|
ANT IN |
OUT |
ANT OUT |
(R) AUDIO (L) |
VIDEO |
|
|
IN |
|
|
|
1 |
|
2 |
|
|
|
|
|
C |
|
VIDEO |
|
AUDIO |
IN OMPONENT |
|
|
|
|
|
|
|
|
|
OUT AV |
OPTICAL |
|
|
|
IN AV |
DIGITAL AUDIO |
|
|
(MONO) |
|
S-VIDEO |
VIDEO |
AUDIO |
1 |
|
OUT |
|
|
|
|
1Connect the S-VIDEO output of the VCR to the S- VIDEO input on the set. The picture quality is improved; compared to normal composite (RCA cable) input.
2Connect the audio outputs of the VCR to the AUDIO input jacks on the set.
3Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
4Select AV1 input source with using the INPUT button on the remote control.
- If connected to AV IN2, select AV2 input source.
Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.
External AV Source Setup
1
Camcorder
Video Game Set |
L AUDIO R VIDEO |
|
1Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
2Select AV2 input source with using the INPUT button on the remote control.
-If connected to AV IN1 input, select AV1 input source.
3Operate the corresponding external equipment. Refer to external equipment operating guide.
•This TV finds the connected input sources automatically for AV1, AV2, Component 1-2, RGB, HDMI1/DVI and HDMI2 sources are connected.
20
Installation
DVD Setup
When connecting with a S-Video cable
DVD
S-VIDEO |
(R) AUDIO (L) |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2
IDEO
OPTICAL
(
DIGITAL AUDIO VIDEO VIDEO
OUT
1 IN VA OUT VA IN OMPONENTC
Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set.
Connect the audio outputs of the DVD to the AUDIO input jacks on the set.
3Turn on the DVD player, insert a DVD.
4Select AV1 input source with using the INPUT button on the remote control. - If connected to AV IN2, select AV 2 input source.
5Refer to the DVD player's manual for operating instructions.
When connecting with a HDMI cable
IN COMPONENT
HDMI IN
2
1(DVI)
ANTENNA/
CABLE IN
1
DVD
HDMI-DVD OUTPUT
1Connect the HDMI output of the DVD to the HDMI IN 1(DVI) or 2 jack on the set.
2Select HDMI1/DVI or HDMI2 input source with using the INPUT button on the remote control.
3Refer to the DVD player's manual for operating instructions.
•TV can receive the video and audio signal simultaneously with using a HDMI cable.
•If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p.
•If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p.
21