Page 1
Global LCD Panel Exchange Center
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
()Preliminary Specification
()Final Specification
Title 17.3” FHD TFT LCD
Customer Fujitsu
MODEL
/
/
SUPPLIER LG Display Co., Ltd.
*MODEL LP173WF1
Suffix TLA2
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY
SIGNATUREAPPROVED BY
APPROVED BY
S. R. Kim / S.Manager
REVIEWED BY
REVIEWED BY
M. J. Lee / Manager
SIGNATURE
SIGNATURE
PREPARED BY
/
Please return 1 copy for your confirmation with
your signature and comments.
Ver. 1.0 Feb. 06, 2012
PREPARED BY
J. P. Lee / Engineer
B. H. Kim / Engineer
Products Engineering Dept.
LG Display Co., Ltd
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1/ 32
www.panelook.com
Page 2
Global LCD Panel Exchange Center
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Contents
No ITEM
COVER
CONTENTS
RECORD OF REVISIONS
1
2
3
4
GENERAL DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
ELECTRICAL CHARACTREISTICS
3-1
INTERFACE CONNECTIONS
3-2
LVDS SIGNAL TIMING SPECIFICATION
3-3
SIGNAL TIMING SPECIFICATIONS
3-4
SIGNAL TIMING WAVEFORMS
3-5
COLOR INPUT DATA REFERNECE
3-6
POWER SEQUENCE
3-7
OPTICAL SFECIFICATIONS
Page
1
2
3
4
5
6
8
9
11
11
12
13
14
5
6 RELIABLITY
7 INTERNATIONAL STANDARDS
8 PACKING
9 PRECAUTIONS
Ver. 1.0 Feb. 06, 2012
MECHANICAL CHARACTERISTICS
7-1 SAFETY
8-1 DESIGNATION OF LOT MARK
8-2 PACKING FORM
8-3 Label Description
A APPENDIX. Enhanced Extended Display Identification Data
17
24
25
26
26
27
28-29
30-32
2/ 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 3
Global LCD Panel Exchange Center
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
RECORD OF REVISIONS
Revision No Revision Date Page Description
0.0 04. Oct, 2011 - First Draft (Preliminary Specification) 0.0
1.0 06. Feb, 2012 - Final Specification 1.0
EDID
ver
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3 / 32
www.panelook.com
Page 4
Global LCD Panel Exchange Center
1. General Description
The LP173WF1 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 17.3 inches diagonally measured active display area with FHD
resolution(1080 vertical by 1920 horizontal pixel array). Each pixel is divided into Red, Green and Blue subpixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is
determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors. The LP173WF1 has been designed to apply the interface method that enables low power, high
speed, low EMI. The LP173WF1 is intended to support applications where thin thickness, low power are
critical factors and graphic displays are important. In combination with the vertical arrangement of the subpixels, the LP173WF1 characteristics provide an excellent flat display for office automation products such as
Notebook PC.
EEPROM Block
EEPROM Block
for EDID
EEPROM Block
EEPROM Block
for Tcon Operating
User connector
for Tcon Operating
for EDID
www.panelook.com
Product Specification
LP173WF1
Liquid Crystal Display
1
1920
TFT-LCD Panel
40
Pin
Timing Control
LVDS
2port
VCC
VLED
LED_EN
PWM
Timing Control
(Tcon) Block
(Tcon) Block
DVCC
Power
Block
LED Driver
LED Driver
Block
TCLKs
Power
Block
Block
VGH, VGL, GMA
Control & Data Power
M
i
n
i
-
L
V
D
S
DVCC, AVDD
GIP CLKs, DSC
VOUT_LED
FB1~6
1080
(FHD, GIP, TN)
Source Driver
(Bottom Bent)
LED Backlight Ass’y
EDID signal & Power
General Features
Active Screen Size 17.3 inches diagonal
Outline Dimension 398.1(H, Typ.) Ý 232.8(V, Typ.) Ý 6.0(D, Max.) mm
Pixel Pitch 0.1989 mm x 0.1989mm
Pixel Format 1920 horiz. By 1080 vert. Pixels RGB strip arrangement
Color Depth 6-bit, 262,144 colors
2
Luminance, White 300 cd/m
Power Consumption Total 8.5W(Typ.) Logic : 2.0W (Typ.@ Mosaic), B/L : 6.5W (Typ.@ VLED 12V )
Weight 630g (Max.)
Display Operating Mode Transmissive mode, normally white
Surface Treatment Glare treatment of the front polarizer
RoHS Comply Yes
BFR / PVC / As Free Yes for All
(Typ.5 point)
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4 / 32
www.panelook.com
Page 5
Global LCD Panel Exchange Center
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter Symbol
Power Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
VCC -0.3 4.0 Vdc at 25 r 5qC
TOP 050qC1
HST -20 60 qC1
HOP 10 90 %RH 1
HST 10 90 %RH 1
Values
Units Notes
Min Max
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39
Wet Bulb
20
]
30
Temperature [
10
0
qC Max, and no condensation of water.
90% 80%
60
50
40
60%
Humidity[(%)RH]
40%
20%
10%
Storage
Operation
-20
10
20 30 40 50
60 70 800
Dry Bulb Temperature []
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5 / 32
www.panelook.com
Page 6
Global LCD Panel Exchange Center
3. Electrical Specifications
3-1. Electrical Characteristics
The LP173WF1 requires two power inputs. The first logic is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second backlight is the input about LED BL with LED Driver.
Parameter Symbol
LOGIC :
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Table 2. ELECTRICAL CHARACTERISTICS
Values
Unit Notes
Min Typ Max
Power Supply Input Voltage V
Power Supply Input Current Mosaic I
Power Consumption P
Power Supply Inrush Current I
LVDS Impedance Z
CC 3.0 3.3 3.6 V 1
CC - 600 680 mA 2
CC - 2.00 2.25 W 2
CC_P - - 1500 mA 3
LVDS 90 100 110
ȳ
BACKLIGHT : ( with LED Driver)
LED Power Input Voltage V
LED Power Input Current I
LED Power Consumption P
LED Power Inrush Current I
LED 7.0 12.0 21.0 V 6
LED - 540 565 mA 6
LED - 6.48 6.78 W 7
LED_P - - 1500 mA 8
PWM Duty Ratio 5 - 100 % 9
PWM Jitter
PWM Impedance Z
PWM Frequency F
-
PWM 20 40 60 kȳ
PWM 200 - 1000 Hz 11
0-0.2%10
5
PWM High Level Voltage V
PWM Low Level Voltage V
LED_EN Impedance Z
LED_EN High Voltage V
LED_EN Low Voltage V
LED_EN_H 3.0 - 5.3 V
LED_EN_L 0-0.5V
PWM_H
PWM_L
PWM 20 40 60 kȳ
3.0 - 5.3 V
0-0.5V
Life Time 12,000 - - Hrs 12
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6 / 32
www.panelook.com
Page 7
Global LCD Panel Exchange Center
Note)
1. The measuring position is the connector of LCM and the test conditions are under 25, fv = 60Hz,
Black pattern.
2. The specified Icc current and power consumption are under
the Vcc = 3.3V , 25, fv = 60Hz condition and Mosaic pattern.
3. This Spec. is the max load condition for the cable impedance designing.
4. The below figures are the measuring Vcc condition and the Vcc control block LGD used.
The Vcc condition is same as the minimum of T1 at Power on sequence.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Rising time
Vcc
0V
5. This impedance value is needed for proper display and measured form LVDS Tx to the mating connector.
6. The measuring position is the connector of LCM and the test conditions are under 25.
7. The current and power consumption with LED Driver are under the Vled = 12.0V , 25, Dimming of
Max luminance and White pattern with the normal frame frequency operated(60Hz).
8. The below figures are the measuring Vled condition
and the Vled control block LGD used.
VLED control block is same with Vcc control block.
90%
10%
0.5ms
3.3V
Rising time
LED
V
0V
10%
12.0V
90%
0.5ms
9. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
10. If Jitter of PWM is bigger than maximum, it may induce flickering.
11. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent
to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for
more consistent brightness control at any specific level desired.
12. The life time is determined as the time at which brightness of LCD is 50% compare to that of minimum
value specified in table 7. under general user conditionU
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7 / 32
www.panelook.com
Page 8
Global LCD Panel Exchange Center
3-2. Interface Connections
This LCD employs two interface connections, a 40 pin connector is used for the module electronics interface
and the other connector is used for the integral backlight system.
Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)
Pin Symbol Description Notes
1 NC No Connection
2 VCC LCD Logic and driver power (3.3V Typ.)
3 VCC LCD Logic and driver power (3.3V Typ.)
4 V EEDID DDC Power (3.3V)
5
6 Clk EEDID DDC Clock
7 DATA EEDID DDC Data
8 ORX0- Negative LVDS differential data input
9 ORX0+ Positive LVDS differential data input
10 GND LCM Ground
11 ORX1- Negative LVDS differential data input
12 ORX1+ Positive LVDS differential data input
13 GND LCM Ground
14 ORX2- Negative LVDS differential data input
15 ORX2+ Positive LVDS differential data input
16 GND LCM Ground
17 ORXC- Negative LVDS differential clock input
18 ORXC+ Positive LVDS differential clock input
19 GND LCM Ground
20 ERX0- Negative LVDS differential data input
21 ERX0+ Positive LVDS differential data input
19 GND LCM Ground
23 ERX1- Negative LVDS differential data input
24 ERX1+ Positive LVDS differential data input
19 GND LCM Ground
26 ERX2- Negative LVDS differential data input
27 ERX2+ Positive LVDS differential data input
19 GND LCM Ground
29 ERXC- Negative LVDS differential clock input
30 ERXC+ Positive LVDS differential clock input
31
32
33
34
35
36
37
38
39
40
NC No Connection
GND LCM Ground (LED Backlight Ground)
GND LCM Ground (LED Backlight Ground)
GND LCM Ground (LED Backlight Ground)
NC
PWM System PWM Signal input for dimming
LED_EN
NC
VLED LED Backlight Power (7V-21V)
VLED LED Backlight Power (7V-21V)
VLED LED Backlight Power (7V-21V)
No Connection
LED Backlight On/Off
No Connection
www.panelook.com
Product Specification
LP173WF1
Liquid Crystal Display
[Interface Chip]
1. LCD :
SiW, SW0617 (LCD Controller)
Including LVDS Receiver.
2. System : SiW LVDS Rx or equivalent
* Pin to Pin compatible with LVDS
[Connector]
Hirose KN38A-40S-0.5H or equivalent
[Mating Connector]
20345-#40E-## series or equivalent
[Connector pin arrangement]
[LCD Module Rear View]
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
8 / 32
www.panelook.com
Page 9
Global LCD Panel Exchange Center
3-3. LVDS Signal Timing Specifications
3-3-1. DC Specification
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Description
LVDS Differential Voltage |V
LVDS Common mode Voltage V
LVDS Input Voltage Range V
3-3-2. AC Specification
Description Symbol Min Max Unit Notes
LVDS Clock to Data Skew Margin
Symb
ol
| 100 600 mV -
ID
CM
IN
t
SKEW
t
SKEW
Min Max Unit Notes
0.6 1.8 V -
0.3 2.1 V -
- 400 + 400 ps
- 600 + 600 ps
85MHz > Fclk ˻
65MHz > Fclk ˻
65MHz
25MHz
LVDS Clock to Clock Skew Margin (Even
to Odd)
Maximum deviation
of input clock frequency during SSC
Maximum modulation frequency
of input clock during SSC
Ver. 1.0 Feb. 06, 2012
t
SKEW_EO
F
DEV
F
MOD
-1/7 + 1/7 T
clk
- · 3% -
- 200 KHz -
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
-
9 / 32
www.panelook.com
Page 10
Global LCD Panel Exchange Center
Freq.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
< Clock skew margin between channel >
F
max
F
center
F
min
3-3-3. Data Format
1) LVDS 2 Port
X
m
tvk
< Spread Spectrum >
m
QGm
Time
kl}
< LVDS Data Format >
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
10 / 3210 / 29
www.panelook.com
Page 11
Global LCD Panel Exchange Center
3-4. Signal Timing Specifications
This is the signal timing required at the input of the User connector. All of the interface signal timing should be
satisfied with the following specifications and specifications of LVDS Tx/Rx for its proper operation.
ITEM Symbol Min Typ Max Unit Note
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Table 4. TIMING TABLE
DCLK Frequency f
Period
Hsync
Width t
Width-Active t
Period t
Vsync
Width-Active t
Horizontal back porch t
Data
Enable
Horizontal front porch t
Vertical back porch t
Vertical front porch t
3-5. Signal Timing Waveforms
Data Enable, Hsync, Vsync
DCLK
tCLK
0.5 Vcc
CLK
t
HP
WH
WHA
VP
WV
WVA
HBP
HFP
VBP
VFP
High: 0.7VCC
Low: 0.3VCC
- 149.8 - MHz
2172 2276 2380
64 96 112
1920 1920 1920
1093 1097 1101
2 3 4
1080 1080 1080
136 196 268
52 64 80
10 12 14
1 2 3
Condition : VCC =3.3V
tCLK
tHPWidth t
tCLK
tHP
t
Hsync
t
WH
t
HBP
HP
tWHA
t
HFP
Data Enable
t
VP
t
WV
Vsync
t
VBP
tWVA
t
VFP
Data Enable
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
11 / 32
www.panelook.com
Page 12
Global LCD Panel Exchange Center
3-6. Color Input Data Reference
The brightness of each primary color (red,green and blue) is based on the 6-bit gray scale data input for the
color ; the higher the binary input, the brighter the color. The table below provides a reference for color
versus data input.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Table 5. COLOR DATA REFERENCE
Input Color Data
Basic
Color
RED
GREEN
BLUE
Color
Black
Red
Green
Blue
Cyan
Magenta
Yellow
White
RED (00)
RED (01)
…
RED (62)
RED (63)
GREEN (00)
GREEN (01)
...
GREEN (62)
GREEN (63)
BLUE (00)
BLUE (01)
…
BLUE (62)
BLUE (63)
RED
MSB LSB
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B 4 B3 B2 B1 B0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
…… …
1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
…… …
0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0
0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
…… …
0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0
0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
MSB LSB
GREEN
BLUE
MSB LSB
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
12 / 32
www.panelook.com
Page 13
Global LCD Panel Exchange Center
3-7. Power Sequence
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Power Supply Input
VCC
Interface Signal, V
i
LVDS
LED on/off control Signal
LED_EN
Dimming control signal
Of LED BL
PWM
LED input Voltage
VLED
0V
0V
0V (Off)
0V (Low)
0V
90%
90%
10%10%
T
T
3
T
T
1
2
T
5
T
9
Valid Data
3.0V
3.0V
T
6
T
10
7
T
4
Valid Data
90%
10%
T
8
T
12
T
11
90%
T
10%
13
Table 6. POWER SEQUENCE TABLE
Logic
Parameter
T
1
T
2
T
3
T
4
T
5
T
6
T
7
Value
Units
Min. Typ. Max.
0.5 - 10 ms
0-50ms
0-50ms
400 - - ms
200 - - ms
200 - - ms
3-10ms
LED
Parameter
T
8
T
9
T
10
T
11
T
12
T
13
Min. Typ. Max.
10 - - ms
0--ms
0--ms
10 - - ms
0.5 - - ms
0 - 5000 ms
Value
Note)
1. Do not insert the mating cable when system turn on.
2. Valid Data have to meet “3-3. LVDS Signal Timing Specifications”
3. LVDS, LED_EN and PWM need to be on pull-down condition on invalid status.
4. LGD recommend the rising sequence of VLED after the Vcc and valid status of LVDS turn on.
Ver. 1.0 Feb. 06, 2012
Units
13 / 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 14
Global LCD Panel Exchange Center
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in
a dark environment at 25
at a viewing angle of
FIG. 1 presents additional information concerning the measurement equipment and method.
qC. The values specified are at an approximate distance 50cm from the LCD surface
) and 4 equal to 0q.
FIG. 1 Optical Characteristic Measurement Equipment and Method
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Optical Stage(x,y)
LCD Module
Pritchard 880 or
equivalent
50cm
Table 8. OPTICAL CHARACTERISTICS
Ta=25qC, VCC=3.3V, fV=60Hz, f
Parameter Symbol
Contrast Ratio CR 500 - - 1
Surface Luminance, white L
Luminance Variation G
Response Time
Color Coordinates
RED RX 0.610 0.640 0.670
GREEN GX 0.290 0.320 0.350
BLUE BX 0.120 0.150 0.180
WHITE WX 0.283 0.313 0.343
Viewing Angle 5
x axis, right()=0q) 4r 60 - - degree
x axis, left ()=180q) 4l 60 - - degree
y axis, up ()=90q) 4u 50 - - degree
y axis, down ()=270q) 4d 50 - - degree
Color Gamut C/G 65 72 - %
Gray Scale 6
WH
WHITE
TrR+ Tr
RY 0.305 0.335 0.365
GY 0.580 0.630 0.660
BY 0.030 0.060 0.090
WY 0.299 0.329 0.359
Min Typ Max
255 300 - cd/m
-1.41.6 3
D
-816ms 4
Values
Units Notes
2
= 149.8MHz
CLK
2
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
14 / 32
www.panelook.com
Page 15
Global LCD Panel Exchange Center
Note)
1. Contrast Ratio(CR) is defined mathematically as
Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels
2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface with
all pixels displaying white. For more information see FIG 1.
= Average(L1,L2, … L5)
L
WH
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
3. The variation in surface luminance , The panel total variation (
G
) is determined by measuring L
WHITE
N
at each test position 1 through 13 and then defined as followed numerical formula.
For more information see FIG 2.
Maximum(L
G
WHITE
=
Minimum(L
4. Response time is the time required for the display to transition from white to black (rise time, Tr
from black to white(Decay Time, Tr
). For additional information see FIG 3.
D
1,L2
1,L2
, … L13)
, … L13)
) and
R
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined
for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the
LCD surface. For more information see FIG 4.
6. Gray scale specification * f
= 60Hz
V
Gray Level Luminance [%] (Typ)
L0 0.11
L7 1.20
L15 5.23
L23 11.8
L31 20.6
L39 34.6
L47 53.3
L55 75.8
L63 100
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
15 / 32
www.panelook.com
Page 16
Global LCD Panel Exchange Center
FIG. 2 Luminance
<Measuring point for Average Luminance & measuring point for Luminance variation>
www.panelook.com
Product Specification
H
A
LP173WF1
Liquid Crystal Display
D
L6
C
L2
B
V
L9
L4 L5
L11 L13
L7
L3
L1
Center Point
L12
L8
L10
H,V : ACTIVE AREA
A : H/4 mm
B : V/4 mm
C : 10 mm
D : 10 mm
POINTS : 13 POINTS
FIG. 3 Response Time
The response time is defined as the following figure and shall be measured by switching the input signal
for “black” and “white”.
Tr
Tr
R
D
%
100
90
Optical
Response
10
0
white
white
black
FIG. 4 Viewing angle
I
= 180
q
<Dimension of viewing angle range>
,
Left
Normal
Eye
Y
I
= 90q, Up
T
I
q
,
Right
I
= 270
q
,
Down
Ver. 1.0 Feb. 06, 2012
I
= 0
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
16 / 32
www.panelook.com
Page 17
Global LCD Panel Exchange Center
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model LP173WF1.
In addition the figures in the next page are detailed mechanical drawing of the LCD.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Horizontal 398.1 r 0.50mm
Outline Dimension
Bezel Area
Active Display Area
Weight 630g (Max.)
Surface Treatment Glare treatment of the front polarizer
Vertical 232.8 r 0.50mm
Depth 6.0mm(Max.)
Horizontal 1.5mm Min.( Lager than Active Display Area )
Vertical 1.5mm Min.( Lager than Active Display Area )
Horizontal 381.888mm
Vertical 214.812 mm
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
17 / 32
www.panelook.com
Page 18
Global LCD Panel Exchange Center
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
<FRONT VIEW>
Note) Unit:[mm], General tolerance:
r 0.5mm
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
18 / 3218 / 30
www.panelook.com
Page 19
Global LCD Panel Exchange Center
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
<REAR VIEW>
Note) Unit:[mm], General tolerance:
r 0.5mm
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
19 / 3219 / 30
www.panelook.com
Page 20
Global LCD Panel Exchange Center
[ DETAIL DESCRIPTION OF SIDE MOUNTING SCREW ]
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
* Mounting Screw Length (A)
= 2.0(Min) / 2.5(Max)
* Mounting Screw Hole Depth (B)
= 2.5(Min)
* Mounting hole location : 3.1(Typ)
* Torque : 2.0 kgf.cm(Max)
(Measurement gauge : torque meter)
Notes : 1. Screw plated through the method of non-electrolytic nickel plating is preferred
to reduce possibility that results in vertical and/or horizontal line defect due to
the conductive particles from screw surface.
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
20 / 32
www.panelook.com
Page 21
Global LCD Panel Exchange Center
LGD Proposal for system cover design.(Appendix)
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
1
Gap check for securing the enough gap between LCM
and System cover.
Max Thickness
Sponge
LCM Reflector Side
System Cover
A Boundary Line
1.Rear side of LCM is sensitive against external stress,and previous check
about interference is highly needed.
Define
2.In case there is something from system cover comes into the boundary
above,mechanical interference may cause the FOS defects.
(Eg:Ripple,White spot..)
2 Check if antenna cable is sufficiently apart from T-CON of LCD Module.
Define
NO GOOD
GOOD
1.If system antenna is overlapped with T-CON,it might be cause the noise.
Ver. 1.0 Feb. 06, 2012
21 / 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 22
Global LCD Panel Exchange Center
LGD Proposal for system cover design.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
3
Gap check for securing the enough gap between LCM
and System hinge.
LCM Reflector Side
Side Mount Screw Hole (4ea)
1.At least 2.0mm of gap needs to be secured to prevent the shock
Define
related defects.
Hinge
GAP:Min2.0mm
(“I” TYPE)
COF
(D-IC)
(“L” TYPE)
2.”L” type of hinge is recommended than “I” type under shock test.
4
Checking the path of the System wire.
LCM Reflector Side
Ok Bad
1.COF area needs to be handled with care.
2.GOOD ÎWire path design to system side.
Define
OKÎ Wire path is located between COFs.
BADÎWire path overlapped with COF area.
Ver. 1.0 Feb. 06, 2012
Good
22 / 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 23
Global LCD Panel Exchange Center
LGD Proposal for system cover design.
5 Using a bracket on the top of LCM is not recommended.
bracket
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
With bracket Without bracket
1.Condition without bracket is good for mechanical noise,and can minimize
the light leakage from deformation of bracket.
Define
2.The results shows that there is no difference between the condition
with or without bracket.
6 Securing additional gap on CNT area..
A
A~A-1
cut
System cover inner side.
User connector
area.
A-1
User connector
Cable pathway.
FPC:Flexible Printed Circuit.
1.CNT area is specially sensitive against external stress,and additional
Define
gap by cutting on system cover will be helpful on removing the Ripple.
2.Using a thinner CNT will be better. (eg: FPC type)
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
23 / 32
www.panelook.com
Page 24
Global LCD Panel Exchange Center
6. Reliability
Environment test condition
No. Test Item Conditions
1 High temperature storage test Ta= 60qC, 240h
2 Low temperature storage test Ta= -20qC, 240h
3 High temperature operation test Ta= 50qC, 50%RH, 240h
4 Low temperature operation test Ta= 0qC, 240h
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
5 Vibration test (non-operating) Sine wave, 10 ~ 500 ~ 10Hz, 1.5G, 0.37oct/min
3 axis, 1hour/axis
6 Shock test (non-operating) Half sine wave, 180G, 2ms
one shock of each six faces(I.e. run 180G 2ms
for all six faces)
7 Altitude operating
storage / shipment
{ Result Evaluation Criteria }
There should be no change which might affect the practical display function when the display quality
test is conducted under normal operating condition.
0 ~ 10,000 feet (3,048m) 24Hr
0 ~ 40,000 feet (12,192m) 24Hr
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
24 / 32
www.panelook.com
Page 25
Global LCD Panel Exchange Center
7. International Standards
7-1. Safety
a) UL 60950-1, Underwriters Laboratories Inc.
Information Technology Equipment - Safety - Part 1 : General Requirements.
b) CAN/CSA C22.2 No.60950-1-07, Canadian Standards Association.
Information Technology Equipment - Safety - Part 1 : General Requirements.
c) EN 60950-1, European Committee for Electrotechnical Standardization (CENELEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.
d) IEC 60950-1, The International Electrotechnical Commission (IEC).
Information Technology Equipment - Safety - Part 1 : General Requirements.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
25 / 32
www.panelook.com
Page 26
Global LCD Panel Exchange Center
8. Packing
8-1. Designation of Lot Mark
a) Lot Mark
ABCDEFGHI JKLM
A,B,C : SIZE(INCH) D : YEAR
E : MONTH F ~ M : SERIAL NO.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Note
1. YEAR
Year
Mark
CBA
2014E2015
D
201320122011
2016G2017H2018J2019
F
2. MONTH
Month
Mark
Apr5May
4
Jun7Jul8Aug9Sep
6
b) Location of Lot Mark
Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
8-2. Packing Form
a) Package quantity in one box : 20 pcs
b) Box Size : 478 x 365 x 328
2020
K
Oct
A
Nov
B
DecMarFebJan
C321
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
26 / 32
www.panelook.com
Page 27
Global LCD Panel Exchange Center
8-3. Label Description
Model Name
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Fujitsu CODE
LGD CODE
Lot Mark
LGD Code
(1) Model Name : L P 1 7 3 W F 1 - T L A 2
(2) Lot Mark : 1 7 3 A 9 C 0 0 0 0 0 0 1
Revision Code
Product Type
Display Mode
Basic Model Serial No.
Resolution : FHD
Size (inch) : 17.3”
Application : NBPC
LGD Brand Initial: L
SERIAL NO.
MONTH
YEAR
SIZE
Fujitsu Code
1)P/N : CP568401-01
2) REV NO : 01A
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
27 / 3227 / 32
www.panelook.com
Page 28
Global LCD Panel Exchange Center
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
9-1. MOUNTING PRECAUTIONS
(1) You must mount a module using holes arranged in four corners or four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
9-2. OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=· 200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
Ver. 1.0 Feb. 06, 2012
28 / 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 29
Global LCD Panel Exchange Center
9-3. ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE
Strong light exposure causes degradation of polarizer and color filter.
9-5. STORAGE
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the
temperature between 5qC and 35qC at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM
(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well
ion-blown equipment or in such a condition, etc.
(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is applied
to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to
remain on the polarizer.
Please carefully peel off the protection film without rubbing it against the polarizer.
(3) When the module with protection film attached is stored for a long time, sometimes there remains a
very small amount of glue still on the polarizer after the protection film is peeled off.
(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is
recognized, please wipe them off with absorbent cotton waste or other soft material like chamois
soaked with normal-hexane.
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
29 / 32
www.panelook.com
Page 30
Global LCD Panel Exchange Center
Feat
DPMS
Off/V
RGB
BLK 1
E
t
b
n
gs
E
r
n
APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 1/3
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Byte
(Dec)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Version
15
16
17
Vendor / Product
Display
Panel Color Coordi
a
s
ish ed
Standard Timing ID Header
18
19
20
21
22
23
Param ete
24
25
26
27
28
29
30
31
32
33
34
35
36
Tim i
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Byte
(Hex)
Header
00
Header
01
Header
02
Header
03
Header
04
Header
05
Header
06
Header
07
EISA manufac ture code ( 3 C haracter ID ) LG D
08
EISA manufacture code (Compressed ASCĊ)
09
Panel Supplier Reserve d - P roduct Cod e 034 8h
0A
( Hex. LSB first )
0B
LCD Module Serial No - Preferred but Optional ("0" If not used)
0C
LCD Module Serial No - Preferred but Optional ("0" If not used)
0D
LCD Module Serial No - Preferred but Optional ("0" If not used)
0E
LCD Module Serial No - Preferred but Optional ("0" If not used)
0F
Week of Manufac ture 0 0 weeks
10
Year o f Manufacture 20 11 years
11
EDID structure version # = 1
12
EDID revision # = 3
13
Video input Definition = Digital signal, 6 bit _ Dell only
14
Max H image size (Round ed cm ) = 3 8 cm
15
Max V image size (Round ed cm ) = 2 2 cm
16
Display gamma = (gamma*100)-100 = Example:(2.2*100)-100=120 = 2.2 Gamma
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
ure Support(no_
Red/Green Low Bits (Rx Ry/GxGy)
Blue/White Low Bits (Bx By/WxWy)
Red X Rx = 0.640
Red Y Ry = 0.335
Green X Gx = 0.320
Green Y Gy = 0.630
Blue X B x = 0 .15 0
Blue Y B y = 0 .06 0
White X Wx = 0.313
White Y Wy = 0.329
Established timing 1 (00h if not used)
Established timing 2 (00h if not used)
Manufacturer's timings (00h if not used)
Standard timing ID1 (01 h if not used)
Standard timing ID1 (01 h if not used)
Standard timing ID2 (01 h if not used)
Standard timing ID2 (01 h if not used)
Standard timing ID3 (01 h if not used)
Standard timing ID3 (01 h if not used)
Standard timing ID4 (01 h if not used)
Standard timing ID4 (01 h if not used)
Standard timing ID5 (01 h if not used)
Standard timing ID5 (01 h if not used)
Standard timing ID6 (01 h if not used)
Standard timing ID6 (01 h if not used)
Standard timing ID7 (01 h if not used)
Standard timing ID7 (01 h if not used)
Standard timing ID8 (01 h if not used)
Standard timing ID8 (01 h if not used)
Field Name and Comments
, no_Active
ery Low Power,
color display, Timing
,no_
Value
(Hex)
00
FF
FF
FF
FF
FF
FF
00
30
E4
48
03
00
00
00
00
00
15
01
03
90
26
16
78
0A
F1
95
A3
55
52
A1
26
0F
50
54
00
00
00
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
Value
(Bin)
00000000
11111111
11111111
11111111
11111111
11111111
11111111
00000000
00110000
11100100
01001000
00000011
00000000
00000000
00000000
00000000
00000000
00010101
00000001
00000011
10010000
00100110
00010110
01111000
00001010
11110001
10010101
10100011
01010101
01010010
10100001
00100110
00001111
01010000
01010100
00000000
00000000
00000000
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
00000001
Ver. 1.0 Feb. 06, 2012
30 / 32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Page 31
Global LCD Panel Exchange Center
c
APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 2/3
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Byte
(Dec)
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
Timing D escriptor #2Timing Descriptor #3 Timing Descriptor #1
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
Byte
(Hex)
Pixel C lock /10,0 00 (LSB) 149 .8 M Hz @ 60 Hz
36
Pixel C lock /10,0 00 (MSB )
37
Horizontal A cti ve (lower 8 bi ts) 1920 Pixels
38
Horizontal B lanking(T hp-HA ) (lowe r 8 b its) 356 Pixels
39
Hor izontal Active / H ori zontal B lan king( Thp -HA) (up per 4:4b its)
3A
Vertic al Avtive 108 0 Lines
3B
Vertic al Blanking (Tvp -HA) (DE Blan king typ.for DE only p anels) 17 L ines
3C
Vertic al Active : Vertica l Blanking (Tvp -HA) (upp er 4:4bits )
3D
Horizontal S ync. Offset (Thfp) 6 4 P ixels
3E
Horizontal S ync P ulse Wid th (HSPW ) 96 Pi xels
3F
Vertic al Sync Offse t(Tvfp) : Sync Width (VS PW ) 2 Line s : 3 Lines
40
Horizontal V ertical Sync Offset/Wi dth (uppe r 2bits)
41
Horizontal I mage Size (mm) 383 mm
42
Vertic al Image Siz e (mm) 215 mm
43
Horizontal Image S ize / Vertical Image Size
44
Horizontal Border = 0 (Zero for Notebook LCD)
45
Vertic al Bo rder = 0 (Zer o for Note book LCD)
46
Non-Interlace , Normal d isplay, no st ereo, Digital Sep arate ( Vsync_N EG, Hsync_ NEG ), D E only note
47
: LSB is set to '1' if panel is DE-timing only. H/V can be ignored.
Flag
48
Flag
49
Flag
4A
Data Type Tag (Descriptor Defined by manufacturer )
4B
Flag
4C
Descriptor Defined by manufac turer
4D
Descriptor Defined by manufac turer
4E
Descriptor Defined by manufac turer
4F
Descriptor Defined by manufac turer
50
Descriptor Defined by manufac turer
51
Descriptor Defined by manufac turer
52
Descriptor Defined by manufac turer
53
Descriptor Defined by manufac turer
54
Descriptor Defined by manufac turer
55
Descriptor Defined by manufac turer
56
Descriptor Defined by manufac turer
57
Descriptor Defined by manufac turer
58
Descriptor Defined by manufac turer
59
Flag
5A
Flag
5B
Flag
5C
Data Type Tag ( ASCII String )
5D
Flag
5E
ASCII Strin g L
5F
ASCII Strin g G
60
ASCII Strin g
61
ASCII Strin g D
62
ASCII Strin g i
63
ASCII Strin g s
64
ASCII Strin g p
65
ASCII Strin g l
66
ASCII Strin g a
67
ASCII Strin g y
68
Manufacturer P/N(If<13 char--> 0Ah , then termi nate with A SC
69
Manufacturer P/N(If<13 char--> 0Ah , then termi nate with A SC
6A
Manufacturer P/N(If<13 char--> 0Ah , then termi nate with A SC
6B
Field Name and Comments
Ċ
Ċ
Ċ
Value
(Hex)
84
3A
80
64
71
38
11
40
40
60
23
00
7F
D7
10
00
00
19
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
FE
00
4C
47
20
44
69
73
70
6C
61
79
0A
20
code 0Ah,set remaining
20
Value
(Bin)
10000100
00111010
10000000
01100100
01110001
00111000
00010001
01000000
01000000
01100000
00100011
00000000
01111111
11010111
00010000
00000000
00000000
00011001
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
00000000
11111110
00000000
01001100
01000111
00100000
01000100
01101001
01110011
01110000
01101100
01100001
01111001
00001010
00100000
00100000
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
31 / 32
www.panelook.com
Page 32
Global LCD Panel Exchange Center
APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM) 3/3
www.panelook.com
LP173WF1
Liquid Crystal Display
Product Specification
Byte
(Dec)
108
109
110
111
112
113
114
115
116
117
118
119
Timing D escriptor #4Che
120
121
122
123
124
125
126
127
Byte
(Hex)
Flag
6C
Flag
6D
Flag
6E
Data T ype Tag ( A SCII Strin g )
6F
Flag
70
ASC II S tring L
71
ASC II S tring P
72
ASC II S tring 1
73
ASC II S tring 7
74
ASC II S tring 3
75
ASC II S tring W
76
ASC II S tring F
77
ASC II S tring 1
78
ASC II S tring -
79
ASC II S tring T
7A
ASC II S tring L
7B
ASC II S tring A
7C
ASC II S tring 2
7D
Extension flag (# of optional 128 panel ID extension block to follow, Typ = 0)
7E
Check Sum (The 1-byte sum of all 128 bytes in this panel ID block shall = 0)
7F
Field Name and Comments
Value
(Hex)
00
00
00
FE
00
4C
50
31
37
33
57
46
31
2D
54
4C
41
32
00
F4
Value
(Bin)
00000000
00000000
00000000
11111110
00000000
01001100
01010000
00110001
00110111
00110011
01010111
01000110
00110001
00101101
01010100
01001100
01000001
00110010
00000000
11110100
Ver. 1.0 Feb. 06, 2012
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
32 / 32
www.panelook.com
Loading...