LG Display LM200WD3-TLC1 Specification
Global LCD Panel Exchange Center
) Preliminary Specification
(
) Final Specification
(
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
BUYER
MODEL
SIGNATURE DATE
/
/
General
20.0” HD+ TFT LCDTitle
SUPPLIER LG Display Co., Ltd.
*MODEL LM200WD3
SUFFIX TLC1
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY
S.G. Hong / G.Manager
REVIEWED BY
D.G. Kim / Manager [C]
Y.H. Hwang / Manager [M]
M.S. Kang / Manager [P]
DATE
/
Please return 1 copy for your confirmation
With your signature and comments.
Ver. 0.1 June, 29, 2010
PREPARED BY
K.H. Oh / Engineer
Product Engineering Dept.
LG Display Co., Ltd
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
1/32
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
Contents
No
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
1)
ELECTRICAL CHARACTERISTICS
2)
INTERFACE CONNECTIONS
4)
SIGNAL TIMING SPECIFICATIONS
5)
SIGNAL TIMING WAVEFORMS
6)
COLOR INPUT DATA REFERNECE
7)
POWER SEQUENCE
8)
POWER DIP CONDITION
OPTICAL SFECIFICATIONS
ITEM
Page
1
2
3
41
52
63
6
8
11LVDS characteristics3)
14
15
16
18
19
194
MECHANICAL CHARACTERISTICS
RELIABILITY
INTERNATIONAL STANDARDS
1)
SAFETY
2)
EMC
PACKING
1)
DESIGNATION OF LOT MARK
2)
PACKING FORM
255
286
297
29
29
29ENVIRONMENT3)
308
30
30
31PRECAUTIONS9
31MOUNTING PRECAUTIONS1)
31OPERATING PRECAUTIONS2)
32ELECTROSTATIC DISCHARGE CONTROL3)
32PRECAUTIONS FOR STRONG LIGHT EXPOSURE4)
32STROAGE5)
32HANDLING PRECAUTIONS FOR PROTECTION FILM6)
Ver. 0.1 June, 29, 2010
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2/32
www.panelook.com
Global LCD Panel Exchange Center
Revision No DescriptionDate Page
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
Record of revisions
Ver.0.1
June,29,2010
Preliminary Specifications.
Ver. 0.1 June, 29, 2010
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
3/32
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
1. General description
LM200WD3-TLC1 is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting
Diode(LED) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally white mode. It has a 20.0 inch
diagonally measured active display area with HD+ resolution (900 vertical by 1600 horizontal pixel
array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in
vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with
a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16.7M colors with
Advanced-FRC(Frame Rate Control). It has been designed to apply the interface method that
enables low power, high speed, low EMI. FPD Link or compatible must be used as a LVDS(Low
Voltage Differential Signaling) chip. It is intended to support applications where thin thickness,
wide viewing angle, low power are critical factors and graphic displays are important. In
combination with the vertical arrangement of the sub-pixels, the LM200WD3-TLC1 characteristics
provide an excellent flat panel display for office automation products such as monitors.
FIG. 1 Block diagram
LVDS
pair #1
LVDS
pair #2
CN1
+5V
V
LCD
Power circuit
block
Timing
controller
RGB
S1
G1
G900
VLED 2ch
Source driver circuit
S1600
TFT-LCD Panel
(1600RGB900 pixels)
Backlight assembly (White LED)
General features
Active screen size 20.0 inches (508.05mm) diagonal
Outline Dimension 462.8(H) x 272.0(V) x 10.2(D) mm(Typ.)
Pixel Pitch 0.0922*RGB(H)mm x 0.2766(V)mm
Pixel Format 1600 horizontal By 900 vertical Pixels. RGB stripe arrangement
Interface LVDS 2Port
Color depth 16.7M colors
Luminance, white 250 cd/m
2
( Center 1Point, typ)
Viewing Angle (CR>10) R/L 170(Typ.), U/D 160(Typ.)
Power Consumption
Total TBD W(Typ.), (TBD W@V
, 9.9 W@IBL= 110 mA)
LCD
Weight 1,150 g (Typ.)
Display operating mode Transmissive mode, normally White
Surface treatments
Ver. 0.1 June, 29, 2010
Hard coating (3H), Anti-glare treatment of the front polarizer
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/32
www.panelook.com
Global LCD Panel Exchange Center
2. Absolute maximum ratings
The following are maximum values which, if exceeded,
may cause faulty operation or damage to the unit.
Table 1. Absolute maximum ratings
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
Values
Parameter Notes
Symbol
Units
MaxMin
Power Supply Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
LCD
OP
ST
OP
ST
C500T
C60-20T
%RH9010H
%RH9010H
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 C Max, and no condensation of water.
Note : 2. Storage condition is guaranteed under packing condition.
FIG. 2 Temperature and relative humidity
90%
60
60%
Wet Bulb
Temperature []
20
10
0
30
40
50
40%
10%
Humidity
[(%)RH]
Storage
Operation
At 25Vdc+6.0-0.3V
1
10 20 30 40 50 60 70 800-20
Dry Bulb Temperature []
Ver. 0.1 June, 29, 2010
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5/32
www.panelook.com
Global LCD Panel Exchange Center
3. Electrical specifications
3-1. Electrical characteristics
It requires two power inputs. One is employed to power the LCD electronics and to drive the
TFT array and liquid crystal. The second input power for the LED/Backlight, is typically
generated by an LED Driver. The LED driver is an external unit to the LCDs.
Table 2. Electrical characteristics
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
Parameter Symbol
Values
MaxTypMin
MODULE :
Power Supply Input Voltage
Permissive Power Input Ripple
Power Supply Input Current
Power Consumption
Inrush current
LCD
LCD
LCD-MOSAIC
LCD-BLACK
I
LCD-L80
LCD
RUSH
Vdc5.55.04.5V
Note :
1. The specified current and power consumption are
under the V
whereas mosaic pattern(8 x 6) is displayed and f
LCD=5.0V, 25 ± 2C,f
=60Hz condition
V
is the frame frequency.
V
2. The current is specified at the maximum current pattern.
3. Permissive power ripple should be measured under VCC=5.0V, 25C, f
(frame frequency)=75Hz
V
condition and At that time, we recommend the bandwidth configuration of oscilloscope
is to be under 20MHz.
4. The duration of rush current is about 5ms and rising time of power Input is 500us ± 20%.
NotesUnit
3V0.4--V
1mATBDTBD-I
2mATBDTBD-I
2mATBDTBD-
1WattTBDTBD-P
3A3.0--I
FIG.3 pattern for Electrical characteristics
power consumption
power input ripple
White : 255Gray
Black : 0Gray
Mosaic Pattern(8 x 6)
Ver. 0.1 June, 29, 2010
Full Black Pattern
Energy star 5.0
White : 255Gray (80%)
Black : 0Gray (20%)
L80 Pattern
6/32
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Table 3. LED array ELECTRICAL CHARACTERISTICS
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
Power Consumption
ConditionSymbolParameter
Values
Max.Typ.Min.
Unit
Notes
1LED :
2mA120110-IsLED String Current
3VTBD44.8-VsLED String Voltage
4,6WattTBD9.9-Parray
5Hrs--30,000LED_LTLED Life Time
Ver. 0.1 June, 29, 2010
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7/32
www.panelook.com
Global LCD Panel Exchange Center
3-2. Interface connections
3-2-1. LCD Module
LCD connector(CN1) : GT103-30S-HF15-E2500 (LSM) , UJU(IS100-L30O-C23)
Mating connector : FI-X30H and FI-X30HL (JAE) or Equivalent
Table 4. Module connector(CN1) pin configuration
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Symbol Description
RXO0-
RXO0+
RXO1-
RXO1+
RXO2-
RXO2+
GND
RXOC-
RXOC+
RXO3-
RXO3+
RXE0-
RXE0+
GND
RXE1-
RXE1+
GND
RXE2-
RXE2+
RXEC-
RXEC+
RXE3-
RXE3+
GND
NC
NC
PWM_OUT
VLCD
VLCD
VLCD
Minus signal of 1st channel 0 (LVDS)
Plus signal of 1st channel 0 (LVDS)
Minus signal of 1st channel 1 (LVDS)
Plus signal of 1st channel 1 (LVDS)
Minus signal of 1st channel 2 (LVDS)
Plus signal of 1st channel 2 (LVDS)
Ground
Minus signal of 1st clock channel (LVDS)
Plus signal of 1st clock channel (LVDS)
Minus signal of 1st channel 3 (LVDS)
Plus signal of 1st channel 3 (LVDS)
Minus signal of 2nd channel 0 (LVDS)
Plus signal of 2nd channel 0 (LVDS)
Ground
Minus signal of 2nd channel 1 (LVDS)
Plus signal of 2nd channel 1 (LVDS)
Ground
Minus signal of 2nd channel 2 (LVDS)
Plus signal of 2nd channel 2 (LVDS)
Minus signal of 2nd clock channel (LVDS)
Plus signal of 2nd clock channel (LVDS)
Minus signal of 2nd channel 3 (LVDS)
Plus signal of 2nd channel 3 (LVDS)
Ground
No Connection (For LCD internal use only.)
No Connection (For LCD internal use only.)
Reference signal for inverter control
Power Supply (5.0V)
Power Supply (5.0V)
Power Supply (5.0V)
Ver. 0.1 June, 29, 2010
PDF created with pdfFactory Pro trial version www.pdffactory.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
8/32
www.panelook.com
Global LCD Panel Exchange Center
FIG. 4 Connector diagram
1’st signal pairs
www.panelook.com
Product Specification
GT103-30S-HF15-ES2500 (LSM)
#
1
#1 #30
2’nd signal pairs
#30
LM200WD3
Liquid Crystal Display
Note:
Power(+5V)
Rear view of LCM
1. NC: No Connection.
2. All GND(ground) pins should be connected together and to Vss which should also
be connected to the LCD’s metal frame.
3. All V
(power input) pins should be connected together.
LCD
4. Input Level of LVDS signal is based on the IEA 664 Standard.
5. PWM_OUT is a reference signal for inverter control.
This PWM signal is synchronized with vertical frequency.
Its frequency is 3 times of vertical frequency, and its duty ratio is 50%.
If the system don’t use this pin, do not connect.
Ver. 0.1 June, 29, 2010
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
9/32
www.panelook.com
Global LCD Panel Exchange Center
3-2-2. LED Interface
The LED interface connector is a model 10019HR-06 manufactured by Yeonho Electronics.
The mating connector is a FFC/FPC specified in LED interface connector specification.
The pin configuration for the connector is shown in the table below.
Table 5. LED connector pin configuration
www.panelook.com
LM200WD3
Liquid Crystal Display
Product Specification
NotesDescriptionSymbolPin
Channel1 Current FeedbackFB11
FIG. 5 Backlight connector view
LED
No connectionNC2
LED Power SupplyVLED3
LED Power SupplyVLED2
No connectionNC3
Channel2 Current FeedbackFB24
Back View
1
Back View
6
PCB
Ver. 0.1 June, 29, 2010
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
10 / 32
www.panelook.com
Loading...