LC200WX1-SL03
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
)
(
(
Preliminary Specification
●
)
Final Specification
20.0” WXGA TFT LCDTitle
GeneralBUYER
-MODEL
*When you obtain standard approval,
www.jxlcd.com
www.jxlcd.com
APPROVED BY
/
/
/
SIGNATURE
DATE
please use the above model name without suffix
APPROVED BY
J.H Yoon / Senior Manager
REVIEWED BY
D.W Lee / Manager
PREPARED BY
Q.H Jo / Engineer
LG.Philips LCD Co., Ltd.SUPPLIER
LC200WX1*MODEL
SL03SUFFIX
SIGNATURE
DATE
Please return 1 copy for your confirmation with
your signature and comments.
Ver. 0.0 Apr. 10, 2006
TV Product Development Dept.
LG. Philips LCD Co., Ltd
1 / 32
COVER
CONTENTS
RECORD OF REVISIONS
GENERAL DESCRIPTION 1
ABSOLUTE MAXIMUM RATINGS 2
ELECTRICAL SPECIFICATIONS 3
ELECTRICAL CHARACTERISTICS 3-1
INTERFACE CONNECTIONS 3-2
SIGNAL TIMING SPECIFICATIONS 3-3
SIGNAL TIMING WAVEFORMS 3-4
COLOR INPUT DATA REFERENCE 3-5
POWER SEQUENCE 3-6
OPTICAL SPECIFICATIONS 4
LC200WX1-SL03
Liquid Crystal Display
Product Specification
CONTENTS
PageITEMNumber
1
2
3
4
5
6
6
8
12
13
14
15
17
MECHANICAL CHARACTERISTICS 5
RELIABILITY 6
www.jxlcd.com
www.jxlcd.com
INTERNATIONAL STANDARDS 7
SAFETY 7-1
EMC 7-2
PACKING 8
DESIGNATION OF LOT MARK 8-1
PACKING FORM 8-2
PRECAUTIONS 9
MOUNTING PRECAUTIONS 9-1
OPERATING PRECAUTIONS 9-2
ELECTROSTATIC DISCHARGE CONTROL 9-3
PRECAUTIONS FOR STRONG LIGHT EXPOSURE 9-4
STORAGE 9-5
HANDLING PRECAUTIONS FOR PROTECTION FILM 9-6
PACKING ASS’YAppendix-Ⅰ
PALLET ASS’YAppendix-Ⅱ
LCM LABELAppendix-Ⅲ
BOX, PALLET LABELAppendix-Ⅳ
21
24
25
25
25
26
26
26
27
27
27
28
28
28
28
A - 1
A - 2
A - 3
A - 4
Ver. 0.0 Apr. 10, 2006
2 / 32
Product Specification
RECORD OF REVISIONS
Preliminary Specification(First Draft)-Apr.10, 20060.0
LC200WX1-SL03
Liquid Crystal Display
DescriptionPageRevision DateRevision No
www.jxlcd.com
www.jxlcd.com
Ver. 0.0 Apr. 10, 2006
3 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
1. General Description
The LC200WX1 is a Color Active Matrix Liquid Crystal Display with an integral External Electrode Fluorescent
Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive display type which is operated in the normally black mode. It has a 20.04 inch diagonally
measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array)
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot,
Therefore it can present a palette of more than 16.7M(true) colors.
It has been designed to apply the 8Bit 1 port LVDS interface.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.
+12.0V
LVDS
5pair
Option
# 9
CN1
(30pin)
www.jxlcd.com
www.jxlcd.com
+24.0V
General Features
SDRAM
MEM
CTRL
RGB
Timing Controller
(LVDS Rx integrated)
(OD Tech.Applied)
Power Circuit
Block
Inverter
(CN2)
EEPROM
(LUT)
SCL
RGB(Mini-LVDS)
SDA
Source Driver Circuit
S1 S1366
G1
Gate Driver Circuit
TFT - LCD Panel
(1366 × RGB × 768 pixels)
G768
Back light Assembly (5CCFL)
20.04 inches (509.016mm) diagonalActive Screen Size
472.0mm(H) x 275.0mm(V) x 38.0mm(D) (Typ.)Outline Dimension
0.108mm x 0.324mm x RGBPixel Pitch
1366 horiz. by 768 vert. pixels RGB stripe arrangementPixel Format
8-bit, 16.7 M colorsColor Depth
500 cd/m2 (Center 1 point Typ.)Luminance, White
Viewing angle free ( R/L 178(Typ.), U/D 178(Typ.)) (TW-IPS Tech. Applied)Viewing Angle (CR>10)
Total 47.98Watt (Typ.) (Logic=3.78W, Lamp=44.2W[Lamp current=5.5mA] ) Power Consumption
2.800 g (Typ.)Weight
Transmissive mode, normally blackDisplay Operating Mode
Anti-glare treatment of the front polarizer, Pencil strength:3HSurface Treatment
Ver. 0.0 Apr. 10, 2006
4 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
2. Absolute Maximum Ratings
The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter Remark
Power Input
Voltage
ON/OFF Control Voltage
Brightness Control Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 °C Max. and no condensation of water.
LCM
Backlight inverter
www.jxlcd.com
www.jxlcd.com
Symbol
Value
MaxMin
+400TOP
+50-20TST
90%
60
60%
Unit
VDC+14.0-0.3VLCD
VDC+5.25-0.3 VON/OFF
VDC+5.0-0.3VBr
°C
°C
%RH9010HOP
%RH 90 10HST
at 25 2 °C
When OperatingVDC+27.0+21.6VBL
Note 1
Wet Bulb
Temperature [℃]
30
20
10
0
10 20 30 40 50 60 70 800-20
Dry Bulb Temperature [°C]
Ver. 0.0 Apr. 10, 2006
50
40
40%
10%
Hu
mi
di
ty
[(
%)
RH
]
Storage
Operation
5 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power for the LCD circuit. The other input power for the
CCFL/Backlight is to power inverter.
Table 2-1. ELECTRICAL CHARACTERISTICS
Parameter Symbol
Circuit :
VLCD Power Input Voltage
VRP Permissible Input Ripple Voltage
ILCD Power Input Current
PLCD Power Consumption
IRUSH Rush current
Note : 1. The specified current and power consumption are under the V
condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at the maximum current pattern.
www.jxlcd.com
www.jxlcd.com
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
White : 255Gray
Black : 0Gray
Value
MaxTypMin
12.612.011.4
200-410315520400-
4.923.78-
3.0--
=12.0V, 25 2°C, fV=60Hz
LCD
VDC
mVP-P
NoteUnit
1mA
2mA
1Watt
3A
Mosaic Pattern(8 x 6)
Ver. 0.0 Apr. 10, 2006
6 / 32
Product Specification
Table 2_2. ELECTRICAL CHARACTERISTICS
LC200WX1-SL03
Liquid Crystal Display
Parameter Symbol
Inverter :
Power Input Voltage
VRP Permissible Input Ripple Voltage
Power Input Current
Power Input Current(Rush)
Power Consumption
Input Voltage for
Control System
Signals
Lamp :
Life Time
Note :
1. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately 120Min
at 25±2°C and Vbr-B = 3.3V.
The specified current and power consumption are under the typical supply Input voltage, 24.0V.
It is total power consumption.
www.jxlcd.com
www.jxlcd.com
Brightness Adjust
On
On/Off
Off
Value
MaxTypMin
VDC25.224.022.8VBL
500--
mVP-P
VDC5.03.52.0V on
VDC0.80.0-0.3V off
NoteUnit
1
1A2.11.84IBL
2A2.8--IRUSH
1W5044.2-PBL
3VDC3.30Vbr-B
4Hrs60,00050,000
2. In rush current is determined at turning on after the unit has been ‘OFF’ for 2 hours at 25±2°C.
3. Brightness Control.
‘Vbr-B’ is a burst dimming-PWM dimming using DC voltage.
FunctionVbr-B Voltage
Maximum Brightness (100%)3.3V
Minimum Brightness.(30%±5%)0V
4. The life time is determined as the time at which luminance of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25 2°C.
Specified value is when lamp is aligned horizontally.
Ver. 0.0 Apr. 10, 2006
7 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
3-2. Interface Connections
This LCD module employs two kinds of interface connection, a 30-pin connector is used for the module
electronics and two 12-pin connectors are used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector(CN1) : IS100-L30B-C23 (Manufactured by JAE) or Equivalent
- Mating Connector : FI-30C2L (Manufactured by JAE) or Equivalent
Table 3. MODULE CONNECTOR(CN1) PIN CONFIGURATION
NoteDescriptionSymbolPin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
www.jxlcd.com
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
www.jxlcd.com
VLCD
VLCD
VLCD
VLCD
GND
Power Supply +12.0V
Power Supply +12.0V
Power Supply +12.0V
Power Supply +12.0V
GroundGND
GroundGND
GroundGND
GroundGND
Select LVDS Data formatSelect
NCNC
GroundGND
LVDS Receiver Signal(-)RALVDS Receiver Signal(+)RA+
GroundGND
LVDS Receiver Signal(-)RBLVDS Receiver Signal(+)RB+
GroundGND
LVDS Receiver Signal(-)RCLVDS Receiver Signal(+)RC+
Ground
LVDS Receiver Clock Signal(-)RCLKLVDS Receiver Clock Signal(+)RCLK+
GroundGND
LVDS Receiver Signal(-)RDLVDS Receiver Signal(+)RD+
GroundGND
NCNC
NCNC
GroundGND
GroundGND
1
Note: 1. If the Pin 9 is Ground, Interface format is “LG”, and if the Pin 9 is Vcc(3.3V), Interface format is
“DISM”. See page 9 and 10.
2. The pin 30 should be ground, this pin 30 is necessary for LCD module test.
3. All GND(ground) pins should be connected together to the LCD module’s metal frame.
4. All VLCD (power input) pins should be connected together.
5. Input Level of LVDS signal is based on the IEA 664 Standard.
Ver. 0.0 Apr. 10, 2006
8 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
Table 4. REQUIRED SIGNAL ASSIGNMENT FOR LVDS TRANSMITTER ( Pin9=“L” or “Open” )
Host System
24 Bit
RED0
RED1
RED2
RED3
RED4
RED5
RED6
RED7
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7
www.jxlcd.com
BLUE0
www.jxlcd.com
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7
Hsync
Vsync
Data Enable
CLOCK
DS90C385
or Compatible
51
TxOUT0-
52
TxOUT0+
54
55
56
TxOUT1-
3
TxOUT1+
50
2
4
TxOUT2-
6
TxOUT2+
7
11
12
TxCLKOUT-
14
TxCLKOUT+
8
10
15
TxOUT3-
19
TxOUT3+
20
22
23
24
16
18
27
28
30
31
FI-X30SSL-HF
48
47
46
45
42
41
40
39
38
37
GND
GND
12
13
15
16
18
19
21
22
24
25
30
Timing
Controller
100Ω
100Ω
100Ω
100Ω
100Ω
9
RxIN0RxIN0+
RxIN1RxIN1+
RxIN2RxIN2+
RxCLKINRxCLKIN+
RxIN3RxIN3+
LG / DISM
LCD Test
LCD Module
Note: 1. The LCD Module uses a 100 Ohm [Ω] resistor between positive and negative lines of each receiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 0.0 Apr. 10, 2006
9 / 32
Product Specification
Table 5. REQUIRED SIGNAL ASSIGNMENT FOR LVDS TRANSMITTER ( Pin9=“H” )
LC200WX1-SL03
Liquid Crystal Display
Host System
24 Bit
RED0
RED1
RED2
RED3
RED4
RED5
RED6
RED7
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7
www.jxlcd.com
BLUE0
www.jxlcd.com
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7
Hsync
Vsync
Data Enable
CLOCK
DS90C385
or Compatible
50
TxOUT0-
2
TxOUT0+
51
52
54
TxOUT1-
55
TxOUT1+
56
3
8
TxOUT2-
10
TxOUT2+
4
6
7
TxCLKOUT-
11
TxCLKOUT+
12
14
16
18
TxOUT3-
15
TxOUT3+
19
20
22
23
24
27
28
30
31
FI-X30SSL-HF
48
47
46
45
42
41
40
39
38
37
GND
Vcc
12
13
15
16
18
19
21
22
24
25
30
Timing
Controller
100Ω
100Ω
100Ω
100Ω
100Ω
9
RxIN0RxIN0+
RxIN1RxIN1+
RxIN2RxIN2+
RxCLKINRxCLKIN+
RxIN3RxIN3+
LG / DISM
LCD Test
LCD Module
Note: 1. The LCD Module uses a 100 Ohm [Ω] resistor between positive and negative lines of each receiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (DS90C385 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data.
Ver. 0.0 Apr. 10, 2006
10 / 32
Product Specification
3-2-2. Backlight Inverter
Inverter Connector : S12B-PH-SM3(manufactured by JST) or Equivalent-
Mating Connector : PHR-12 or Equivalent-
Table 6. INVERTER CONNECTOR PIN CONFIGULATION
LC200WX1-SL03
Liquid Crystal Display
NoteDescriptionSymbolPin No
1
2
3
4
5
6
7
8
9
10
11
www.jxlcd.com
www.jxlcd.com
12
1. GND is connected to the LCD module’s metal frame.
Vbr-B
On/Off
PCB
Power Supply +24.0VVBL
Power Supply +24.0VVBL
Power Supply +24.0VVBL
Power Supply +24.0VVBL
Power Supply +24.0VVBL
POWER GNDGND
POWER GNDGND
POWER GNDGND
POWER GNDGND
POWER GNDGND
PWM Dimming
(0V ~ 3.3V)
Backlight On/Off control
(0V ~ 5.0V)
Note :
1 2
(JST : Japan Solderless Terminal Co.,Ltd.)
3
S12B-PH-SM3-TB
10
11
12
1
2
3
2. 0V : Minimum Brightness.
3.3V : Maximum Brightness.
3. On : 2.0 ~ 5.25V
Off : -0.3 ~ 0.8V
Ver. 0.0 Apr. 10, 2006
11 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
3-3. Signal Timing Specifications
This is the signal timing required at the input of the LVDS transmitter. All of the interface signal timing should
be satisfied with the following specification for it’s proper operation.
Table 7. TIMMING TABLE
RemarkUnitMaxTypMinSymbolITEM
ns14.713.812.5tCLK Period
DCLK
MHz8072.368- Frequency
tCLK177615281456tHPPeriod
Hsync
Vsync
www.jxlcd.com
www.jxlcd.com
DE
(Data
Enable)
Note : Hsync Period and Hsync Width should be even number times of tCLK. If the value is odd number
times of tCLK, display control signal can be asynchronous. In order to operate the LCD,
Vsync and DE(Data Enable) signals should be used.
1. The performance of the electro-optical characteristics may be influenced by variance of the vertical
refresh rate.
2. Vsync and Hsync should be keep the above specification.
3. Hsync Period, Hsync Width and Horizontal Back Porch should be any times of character number(4).
Horizontal Blank
-
Hsync,
5047.445fHFrequency
-52tWV Width
136613661366tHVHorizontal Valid
-8024tHBPHorizontal Back Porch
-4824tHFPHorizontal Front Porch
tHP- tHV160tHP- tHV
768768768tVVVertical Valid
-154tVBPVertical Back Porch
-21tVFPVertical Front Porch
tVP- tVV227- Vertical Blank
KHz
tCLK-328tWH Width
tHP1063790775tVP Period
Hz636047fV Frequency
tHP
tCLK
tHP
Note 1)
PAL : 47~53Hz
NTSC : 57~63Hz
Ver. 0.0 Apr. 10, 2006
12 / 32
3-4. Signal Timing Waveforms
LC200WX1-SL03
Liquid Crystal Display
Product Specification
DCLK
First data
Second data
DE(Data Enable)
www.jxlcd.com
www.jxlcd.com
Hsync, Vsync, DE, Data
tCLK
0.5 VDD
Invalid data
Invalid data
Pixel 0,0
Valid data
Pixel 1,0
0.7VDD
Valid data
Pixel 2,0
Pixel 3,0
0.3VDD
Invalid data
Invalid data
tHP
HSync
DE(Data Enable)
VSync
DE(Data Enable)
Ver. 0.0 Apr. 10, 2006
tWH
tWV
tHBP tHV
tVP
tVBP
tVV tVFP
tHFP
13 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
3-5. Color Data Reference
The brightness of each primary color(red,green,blue) is based on the 8-bit gray scale data input for the color
the higher the binary input, the brighter the color. The below table provides a reference for color versus data
input.
Table 8. COLOR DATA REFERENCE
Input Color Data
Basic
Color
RED
Color
Black 0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0
Red (255)
Green (255)
Blue (255)
Cyan
Magenta
Yellow
White
www.jxlcd.com
www.jxlcd.com
MSB LSB
RED
GREEN
MSB LSB
MSB LSB
B7 B6 B5 B4 B3 B2 B1 B0G7 G6 G5 G4 G3 G2 G1 G0R7 R6 R5 R4 R3 R2 R1 R0
BLUE
0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 1
0 0 0 0 0 0 0 01 1 1 1 1 1 1 10 0 0 0 0 0 0 0
1 1 1 1 1 1 1 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0
1 1 1 1 1 1 1 11 1 1 1 1 1 1 10 0 0 0 0 0 0 0
1 1 1 1 1 1 1 10 0 0 0 0 0 0 01 1 1 1 1 1 1 1
0 0 0 0 0 0 0 01 1 1 1 1 1 1 11 1 1 1 1 1 1 1
1 1 1 1 1 1 1 11 1 1 1 1 1 1 11 1 1 1 1 1 1 1
0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0RED (000) Dark
0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 1RED (001)
............
0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 0RED (254)
0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 1RED (255)
0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0GREEN (000) Dark
GREEN
BLUE (000) Dark
BLUE
Note : Users should be input true 8 Bit data streams via LVDS transmitter.
Ver. 0.0 Apr. 10, 2006
0 0 0 0 0 0 0 00 0 0 0 0 0 0 10 0 0 0 0 0 0 0GREEN (001)
............
0 0 0 0 0 0 0 01 1 1 1 1 1 1 00 0 0 0 0 0 0 0GREEN (254)
0 0 0 0 0 0 0 01 1 1 1 1 1 1 10 0 0 0 0 0 0 0GREEN (255)
0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0
0 0 0 0 0 0 0 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (001)
............
1 1 1 1 1 1 1 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (254)
1 1 1 1 1 1 1 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (255)
14 / 32
3-6. Power Sequence
3-6-1. LCD Driving circuit
Power For LCD
V
LCD
0V
Product Specification
90% 90%
10%
T1 T2 T5 T6 T7
LC200WX1-SL03
Liquid Crystal Display
10%
Interface Signal (Tx)
Power for LAMP
Table 9. POWER SEQUENCE FOR LCD DRIVING CIRCUIT
www.jxlcd.com
www.jxlcd.com
Parameter
Value
Valid Data
T3 T4
Lamp ON
MaxTypMin
20-0.5T1
--200T3
--200T4
300--T6
Unit
ms
ms
ms
ms
ms
ms
s
Note
450-0.5T2
5
450-0.5T5
3--1.0T7
Note : 1. Please avoid the floating state of interface signal at invalid period.
2. When the interface signal is invalid, be sure to pull down the power supply V
3. Flicker would come out when power on-off(T7=1s) is tested over several ten-times.
4. The case when the T2/T5 exceed maximum specification, it operates protection
pattern(Black pattern) till valid signal inputted. There is no reliability problem.
5. The T3/T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
6. The input timing of valid data is regarded by CLK and LVDS Signal (contains no undesirable
high or low level noise) enters.
Ver. 0.0 Apr. 10, 2006
LCD
to 0V.
15 / 32
3-6-2. On/Off for Inverter
Power Supply For Inverter
LC200WX1-SL03
Liquid Crystal Display
Product Specification
24V (typ.)
90%
V
3-6-3. Deep condition for Inverter
BL
0V
Enable
(On/Off)
VBr
www.jxlcd.com
www.jxlcd.com
V
BL
VBL(min) x 0.8
10%
TB1 TB2
10%
TB3
TB4
TB5
0 V
Table 10. POWER SEQUENCE FOR INVERTER
Parameter
Value
MaxTypMin
10--TB5
Note : 1. TB1 describes rising time of 0V to 24V and is not applied at restarting time.
2. When VBL (24V) is supplied always, there is no reliability problem.
Ver. 0.0 Apr. 10, 2006
Unit
ms--15TB1
ms--500TB2
ms--0TB3
ms--0TB4
ms
Remark
After Inverter’s connected
VBL(min) x 0.8
16 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ for 30 minutes in a dark environment at
25±2°C. The values are specified at an approximate distance 50cm from the LCD surface at a viewing angle
of and equal to 0 °.
It is presented additional information concerning the measurement equipment and method in FIG. 1.
Optical Stage(x,y)
FIG. 1 Optical Characteristic Measurement Equipment and Method
LCD Module
50cm
Pritchard 880 or
equivalent
Table 11. OPTICAL CHARACTERISTICS
SymbolParameter
www.jxlcd.com
www.jxlcd.com
Surface Luminance, white
Luminance Variation
Rise Time
Response Time
Color Coordinates
[CIE1931]
Viewing Angle (CR>10)
x axis, right(=0°)
x axis, left (=180°)
y axis, up (=90°)
y axis, down (=270°)
Ver. 0.0 Apr. 10, 2006
Decay Time
G to G
RED
GREEN
BLUE
WHITE
Diagonal Front
(=45°)
(=135°)
(=225°)
(=315°)
WH
WHITE
R
D
Rx
Ta= 25±2°C, V
5P
-0.03
Typ
=12.0V, fV=60Hz, Dclk=72.3MHz, Vbr-B=3.3V
LCD
Value
MaxTypMin
550 400CR Contrast Ratio
2
500400L
0.636
0.342Ry
0.280Gx
0.605Gy
0.146Bx
0.064By
0.272Wx
0.278Wy
128-Tr
149-Tr
148-
Typ
+0.03
-8985r
-8985l
-8985u
-8985d
2cd/m
NoteUnit
1
31.3
4ms
5degree
6 Gray Scale
17 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
Note :
1. Contrast Ratio(CR) is defined mathematically as :
Contrast Ratio = Maximum CRn (n=1, 2, 3, 4, 5)
Surface Luminance with all white pixels
Contrast Ratio =
Surface Luminance with all black pixels
n = the Position number(1, 2, 3, 4, 5), For more information, see FIG 2.
2. Surface Luminance(LWH) is the luminance value at center 1-point across the LCD surface 50cm
from the surface with all pixels displaying white. For more information see the FIG. 2.
3. The variation of surface luminance , WHITE is defined as :
WHITE(5P) = Maximum(L
Where L
4. Response time is the time required for the display to transition from G(N) to G(M) (Rise Time, TrR)
and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M)
to L
on1
For more information, see the FIG. 2.
are the luminance with all pixels displaying white at 5 locations .
on5
on1,Lon2
, L
on3
, L
on4
, L
) / Minimum(L
on5
on1,Lon2
, L
on3
, L
on4
, L
on5
)
5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis
which
is normal to the LCD module surface. For more information, see the FIG. 4. & FIG. 5.
6. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 12.
Table 12. GRAY SCALE SPECIFICATION
www.jxlcd.com
www.jxlcd.com
Luminance [%] (Typ)Gray Level
L0
L15
L31
L47
L63
L79
L95
L111
L127
L143
L159
L175
L191
L207
L223
L239
L255
0.17
0.27
1.00
2.40
4.60
7.60
11.40
16.00
21.60
28.00
35.40
43.70
53.00
63.20
74.50
88.00
100.00
Ver. 0.0 Apr. 10, 2006
18 / 32
Product Specification
Measuring point for surface luminance & measuring point for luminance variation
H
A
③②
LC200WX1-SL03
Liquid Crystal Display
V
B
④
%
90
FIG. 2 The Position of Points for Luminance Measure
TrR
www.jxlcd.com
www.jxlcd.com
Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Gray(M)”.
100
①
⑤
A : H / 4 mm
B : V / 4 mm
H : 443.609 mm
V : 249.408 mm
@ H,V : Active Area
TrD
Optical
Response
10
0
Ver. 0.0 Apr. 10, 2006
Gray(N)
N,M = 0(Black)~255(White), N<M
FIG. 3 Response Time
Gray(M)
Gray(N)
19 / 32
Dimension of viewing angle range
Normal
Y
E
= 0, Right
= 180, Left
= 270, Down
= 90, Up
LC200WX1-SL03
Liquid Crystal Display
Product Specification
FIG. 4 Viewing Angle
www.jxlcd.com
Optical characteristics are determined after the unit has been ‘ON’ for 30min in a dark environment at 25±2°C.
The values specified are at an approximate distance 1.2mm from the LCD surface at a viewing angle of and
equal to 0 °.
It is presented additional information concerning the measurement equipment and method in FIG. 1.
www.jxlcd.com
EZ Contrast
UP
r=45˚
l=135˚
1.2 ~ 1.5㎜
u=225˚
DOWN
d=315˚
=0˚
FIG. 5 Diagonal Viewing Angle Measurement Condition
Ver. 0.0 Apr. 10, 2006
20 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
5. Mechanical Characteristics
The following items provide general mechanical characteristics. In addition, the figures in the next page show
the detail information of mechanical drawing for LCD module.
Table 13. MECHANICAL CHARACTERISTICS
472.0mmHorizontal
Outline Dimension
Bezel Area
Active Display Area
(Typ.) 2,800 (g), (Max.) 3,000(g)Weight
Surface Treatment
www.jxlcd.com
Note : Please refer to a mechanic drawing in terms of tolerance at the next page.
www.jxlcd.com
Hard coating(3H)
Anti-glare treatment of the front polarizer
275.0mmVertical
38.0mmDepth
448.0mmHorizontal
253.8mmVertical
443.609mmHorizontal
249.408mmVertical
Ver. 0.0 Apr. 10, 2006
21 / 32
<FRONT VIEW>
LC200WX1-SL03
Liquid Crystal Display
Product Specification
www.jxlcd.com
www.jxlcd.com
Ver. 0.0 Apr. 10, 2006
22 / 32
<REAR VIEW>
LC200WX1-SL03
Liquid Crystal Display
Product Specification
www.jxlcd.com
www.jxlcd.com
Ver. 0.0 Apr. 10, 2006
23 / 32
Product Specification
6. Reliability
Table 14. ENVIRONMENT TEST CONDITION
Vibration test
5
(non-operating)
LC200WX1-SL03
Liquid Crystal Display
ConditionTest ItemNo.
Ta= 50°C 240hHigh temperature storage test1
Ta= -20°C 240hLow temperature storage test2
Ta= 40°C 50%RH 240hHigh temperature operation test3
Ta= 0°C 240hLow temperature operation test4
Wave form : random
Vibration level : 1.0Grms
Bandwidth : 10-500Hz
Duration : X,Y,Z, 10 min
One time each direction
Shock test
6
(non-operating)
www.jxlcd.com
www.jxlcd.com
Altitude operating
8
storage / shipment
Shock level : 100Grms
Waveform : half sine wave, 2ms
Direction : ±X, ±Y, ±Z
One time each direction
Ta= 40 °C 90%RH 240hHumidity condition Operation7
0 - 14,000 feet(4267.2m)
0 - 40,000 feet(12192m)
Ver. 0.0 Apr. 10, 2006
24 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
7. International standards
7-1. Safety
a) UL 60950, Third Edition, Underwriters Laboratories, Inc., Dated Dec. 11, 2000.
Standard for Safety of Information Technology Equipment, Including Electrical Business
Equipment.
b) CAN/CSA C22.2, No. 60950, Third Edition, Canadian Standards Association, Dec. 1,
2000.
Standard for Safety of Information Technology Equipment, Including Electrical Business
Equipment.
c) EN 60950 : 2000, Third Edition
IEC 60950 : 1999, Third Edition
European Committee for Electrotechnical Standardization(CENELEC)
EUROPEAN STANDARD for Safety of Information Technology Equipment Including
7-2. EMC
Business Equipment.
a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage
Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards
1992
b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of
Technology Equipment.“ International Special Committee on Radio Interference.
Technology Equipment.“ European Committee for Electrotechnical
Standardization.(CENELEC), 1998
( Including A1: 2000 )
www.jxlcd.com
www.jxlcd.com
c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of
Electrical
Electrical and
Institute(ANSI),
Information
Information
Ver. 0.0 Apr. 10, 2006
25 / 32
Product Specification
8-1. Designation of Lot Mark
a) Lot Mark
A B C D E F G H I J K L M
A,B,C : SIZE(INCH) D : YEAR
E : MONTH F : FACTORY CODE
G : ASSEMBLY CODE H, I, J, K, L, M : SERIAL NO.
Note
1. YEAR
LC200WX1-SL03
Liquid Crystal Display
Year
Mark
2. MONTH
Month
Mark
www.jxlcd.com
3. FACTORY CODE
Factory Code
4. SERIAL NO.
Mark
b) Location of Lot Mark
Serial No. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.
www.jxlcd.com
LPL Gumi
Mark
100001~199999, 200001~299999, 300001~399999, …., A00001~A99999, ….., Z00001~Z99999
K
200320022001
200452005
321
Apr5May
LPL Nanjing
C
4
4
2006720078200892009
6
Jun7Jul8Aug9Sep
6
HEESUNG
D
2010
0
Oct
A
Nov
B
DecMarFebJan
C321
8-2. Packing Form
a) Package quantity in one box : 4 pcs
b) Box Size : 530mm X 310mm X 327mm
Ver. 0.0 Apr. 10, 2006
26 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1) You must mount a module using holes arranged in four rears & four sides.
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that
external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes
circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the
www.jxlcd.com
www.jxlcd.com
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
9-2. Operating Precautions
(9) Do not open the case because inside circuits do not have sufficient strength.
deformations and color fading.
adhesives
cause
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer.
(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it causes metallic foreign material and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
Ver. 0.0 Apr. 10, 2006
27 / 32
LC200WX1-SL03
Liquid Crystal Display
Product Specification
9-3. Electrostatic Discharge Control
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.
9-4. Precautions for Strong Light Exposure
Strong light exposure causes degradation of polarizer and color filter.
9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
9-6. Handling Precautions for Protection Film
(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.
www.jxlcd.com
www.jxlcd.com
Ver. 0.0 Apr. 10, 2006
28 / 32
Product Specification
# APPENDIX-Ⅰ
■LC200WX1-SL03 - Packing Ass’y
LC200WX1-SL03
Liquid Crystal Display
www.jxlcd.com
www.jxlcd.com
DESCRIPTIONNO.
LCD Module1
3
4
5
TAPE
Packing
Packing
Packing6
BOTTOM, EPS LC200WX1
TOP(LEFT), EPS LC200WX1
TOP(RIGHT), EPS LC200WX1
YUPO PAPER 80G 100X100Label9
MATERIAL
PE 525X395BAG2
MASKING 20MMX50M
SWR4 530X310X327BOX7
OPP 70MMX300MTAPE8
Ver. 0.0 Apr. 10, 2006
29 / 32
LC200WX1-SL03
Liquid Crystal Display
# APPENDIX 2
# APPENDIX- Ⅱ
■ LC200WX1-SL03 Pallet Ass’y
Product Specification
www.jxlcd.com
www.jxlcd.com
DESCRIPTIONNO.
PACKING ASS’Y1
STEEL_1100X1000X130PALLET2
4
ANGLE,
PACKING
P.P 18MMX200MX0.8MMBAND, PACKING6
LABEL8
MATERIAL
DW3 1100X1000SHEET3
DW3 1113X980X1020
DW3 1135X1000X100ANGLE, COVER5
CLIP 18MMBAND, CLIP7
PALLET YUPO PAPER
102X165
Ver. 0.0 Apr. 10, 2006
30 / 32
LC200WX1-SL03
Liquid Crystal Display
# APPENDIX 3
# APPENDIX- Ⅲ
■ LCM Label
Model
UL, TUV Mark
LPL Logo
US PATENT No. Origin
Product Specification
Serial No.
www.jxlcd.com
www.jxlcd.com
■ Serial No. (See CAS 26page for more information)
1 2 3 4 5 6 7 9 10 11 12
Inch
MonthYear
M Ass’y Factory code
8
Serial No.
M A,ssy Line code
13
Ver. 0.0 Apr. 10, 2006
31 / 32
LC200WX1-SL03
Liquid Crystal Display
# APPENDIX 4
■ Box Label ■ Pallet Label
Product Specification
www.jxlcd.com
www.jxlcd.com
Ver. 0.0 Apr. 10, 2006
32 / 32
Loading...