LG Z65143B User Manual

OWNER’S MANUAL

DUAL FUEL RANGE

Read this owner’s manual thoroughly before operating the appliance

ENGLISH ESPAÑOL

and keep it handy for reference at all times.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

%Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

%WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

- If you cannot reach your gas supplier, call the fire department.

%Installation and service must be performed by a qualified installer, service

agency, or the gas supplier.

SKSDR480SIS

MFL68920520_00

www.thesignaturekitchen.com

TABLE OF CONTENTS

IMPORTANT SAFETY

INSTRUCTIONS

PRODUCT OVERVIEW

15 Parts 15 Accessories

INSTALLATION

16 Installation Overview 16 Product Specifications 17 Before Installing the Range 19 Ventilation Requirement 19 Proper Location 22 Gas Supply 22 Electrical Supply 22 Installing the Range 26 Connecting the Range to Gas 27 Connecting Electricity 30 Engaging the Anti-tip Device 31 Test Run 31 Checking Ignition of the Surface Burners

OPERATION

33 Control Panel Overview 34 Getting Started 34 Changing Oven Settings 39 Using the Cooktop

39 Gas Cooktop Module 39 Cooktop Timers

40 The Gas Surface Burners

40 Before Use 40 Using the Gas Surface Burners 41 Setting the Flame Size 41 In Case of Power Failure 41 Cookware for Gas Burners 42 Extra Low Simmer (Small Burners Only) 42 Using a Wok 43 Using Stove-Top Grills

43 Induction Cooktop (On Some Models)

43 Benefits of Induction Surface Cooking 44 Induction Cookware 44 Cookware Placement 45 Moving Cookware on the Cooktop 45 Pan Sensing 45 Setting Surface Controls 46 Hot Surface Indicator 46 Using the Cooking Elements 46 Flex Mode 47 The Recommended Surface Cooking

Setting 47 Pan Preheat Recommendations 47 Noises during Induction Operation 47 Power Management

48 Sous Vide (On Some Models)

48 Vacuum Sealing 48 Using Sous Vide 49 Using the Rack 49 No Preheating Cooking 49 Moving the Sous Vide Bath 50 Setting the Temperature 50 Setting the Cook Time 51 Using Oven Racks 51 Filling the Water 51 Sous Vide Cook Guide

52 Using the Oven

52 Before Using the Oven 52 Oven Vent 52 Using Oven Racks 53 Accessories for Right Oven 53 Accessories for Left Oven 54 Timer 54 Bake 55 Convection Modes 56 Rapidheat Roast 57 Recommended Baking and Roasting Guide 58 Broil 59 Recommended Broiling Guide 60 Warm 60 Proof 61 Probe 62 My Recipe 62 Auto Cook 63 Steam Function(Left Oven Only) 64 Remote Start

TABLE OF CONTENTS

ENGLISH

SMART FUNCTIONS

65 SIGNATURE KITCHEN SUITE Application 66 Smart Diagnosis™ Function 67 Open Source Software Notice Information 68 FCC Notice 68 FCC RF Radiation Exposure Statement

MAINTENANCE

69 Control Panel 69 Gas Surface Burners 70 Burner Grates 70 Gas Cooktop Surface 71 Sous Vide Module 71 Induction Cooktop 73 Exterior 74 Front Manifold Panel and Knobs 75 SpeedClean™ (Right Oven) 77 SpeedClean™ (Left Oven) 77 Self Clean (Right Oven Only) 79 Oven Air Vents 79 Steam Feeder Tank 80 Descaling 80 Drying 80 Evaporation 81 Removing and Replacing the Lift-Off Oven

Doors

TROUBLESHOOTING

82 FAQs 84 Before Calling for Service

WARRANTY

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions when using the range to prevent the risk of fire, electric shock, personal injury, or damage. This guide does not cover all possible conditions that may occur. Always contact your service agent or manufacturer about problems that you do not understand.

Download this owner's manual at: www.thesignaturekitchen.com

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property damage and/or serious bodily harm or death. All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION. These words mean:

WARNING

CAUTION

- Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result

in minor or moderate injury.

ANTI-TIP DEVICE

WARNING

%TO REDUCE THE RISK OF TIPPING, THE APPLIANCE MUST BE SECURED

BY A PROPERLY INSTALLED ANTI-TIP DEVICE. TO CHECK IF THE DEVICE IS INSTALLED PROPERLY, VERIFY THAT THE ANTI-TIP DEVICE IS ENGAGED, OR GRASP THE TOP REAR EDGE OF THE RANGE BACK GUARD AND CAREFULLY ATTEMPT TO TILT IT FORWARD. Refer to the installation section for instructions.

%A child or adult can tip the range and be killed. %Install the anti-tip device to the structure and/or the range. Verify the anti-tip device has

been properly installed and engaged following the instructions on the anti-tip bracket template.

%Engage the range to the anti-tip device following the instructions on the anti-tip bracket

template. Ensure the anti-tip device is re-engaged when the range is moved by following the instruction on the anti-tip bracket template.

%Re-engage the anti-tip device if the range is moved. Do not operate the range without

the anti-tip device in place and engaged. %See installation instructions for details. %Failure to do so can result in death or serious burns to children or adults.

%Never remove the oven legs. The range will not be secured to the

anti-tip bracket if the legs are removed.

%Do not step or sit on the oven door. The range could be tipped and

injury might result from spilled hot liquid, food, or the range itself.

%Do not rest large, heavy items such as whole turkeys on the open

oven door. The range could tip forward and cause injury.

%Reengage the anti-tip device after pulling the range out for

cleaning, service, or any other reason.

%Failure to follow these instructions can result in death or serious

burns to children or adults.

Leveling leg

Anti-tip bracket

IMPORTANT SAFETY INSTRUCTIONS

INSTALLATION SAFETY PRECAUTIONS

Have the installer show you the location of the range gas shut-off valve and how to shut it off if necessary.

WARNING

%Make sure the range is properly installed and grounded by a qualified installer,

according to the installation instructions. Any adjustment and service should be

performed only by qualified gas range installers or service technicians. %Make sure the range is properly adjusted by a qualified service technician or installer

for the type of gas (natural or LP) that is to be used. The range can be converted for

use with either type of gas. See the installation instructions. %These adjustments must be done by a qualified service technician according to the

manufacturer’s instructions and all codes and requirements of the authority having

jurisdiction. Failure to follow these instructions could result in serious injury or property

damage. The qualified agency performing these adjustments assumes responsibility for

the conversion. %Disconnect the electrical supply before servicing the appliance. %Never use the appliance door as a step stool or seat, as this may result in tipping of the

appliance and serious injuries. %This product should not be installed below ventilation type hood systems that direct air

in a downward direction.

Doing so may cause ignition and combustion problems with the cooktop resulting in

personal injury and may affect the cooking performance of the unit. %To prevent fire hazard or electrical shock, do not use an adapter plug or an extension

cord, or remove the grounding prong from the electrical power cord. Failure to follow

this warning can cause serious injury, fire or death. %To prevent poor air circulation, place the range out of the kitchen traffic path and out of

drafty locations. %Do not attempt to repair or replace any part of the range unless it is specifically

mentioned in this manual. All other services should be referred to a qualified technician. %Make sure that all packaging materials are removed from the range before operating it

to prevent fire or smoke damage should the packaging material ignite. %After using the range for an extended period of time high floor temperatures may result.

Many floor coverings will not withstand this kind of use. %Never install the range over vinyl tile or linoleum that cannot withstand such type of

use. Never install it directly over interior kitchen carpeting.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

The Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances known to the state to cause birth defects or other reproductive harm, and requires businesses to warn customers of potential exposure to such substances. Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde and soot, caused primarily by the imperfect combustion of natural or LP gas. Correctly adjusted burners, indicated by a bluish rather than a yellow flame, will minimize imperfect combustion. Exposure to these substances can be minimized by opening windows or using a ventilation fan or hood.

WARNING

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. (US only)

%DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES OF OVEN. Heating

elements may be hot even though they are dark in color. Interior surfaces of an oven become hot enough to cause burns. During and after use, do not touch or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces, such as oven vent openings and surfaces near these openings, oven doors, and windows of oven doors, also get hot and may cause burns if not cooled.

%Use care when opening door. The hot air and steam that escape can cause burns to

hands, face and eyes. Let hot air or steam escape from the oven before removing or replacing food in the oven.

%Do not repair or replace any part of the appliance unless specifically recommended in the

manual. All other servicing should be performed by a qualified technician.

%Do not use harsh etching, abrasive cleaners or sharp metal scrapers to clean the oven

door glass since they can scratch the surface. Scratches may cause the glass to shatter.

WARNING

If the door glass, surface, or oven heating unit of the range are damaged, discontinue use of the range and call for service.

%Do not use plastic to cover food. Use foil or oven-safe lids only. %Do not allow anyone to climb, stand or hang on the door or cooktop. They could damage

the range and even tip it over, causing severe personal injury.

%Do not line the oven walls, racks, bottom, or any other part of the oven with aluminum foil

or any other material. Doing so will disrupt heat distribution, produce poor baking results and cause permanent damage to the oven interior (aluminum foil will melt to the interior

surface of the oven) %Never attempt to dry a pet in the oven. %Never use your appliance for warming or heating the room. %Always use pot holders or oven mitts when removing food from the oven or the surface

element. Cookware will be hot. Use only dry pot holders. Moist or damp pot holders on

hot surfaces may result in burns from steam. Do not let the pot holder touch hot heating

elements. Do not use a towel or other bulky cloth to remove food. %Do not heat unopened food containers. Pressure in the containers may cause them to

burst which may result in injury. %Large scratches or impacts to glass doors can lead to broken or shattered glass. %Leak testing of the appliance must be conducted according to the manufacturer’s

instructions.

IMPORTANT SAFETY INSTRUCTIONS

%To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage

space located above the surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood that projects horizontally a

minimum of 5 inches beyond the bottom of the cabinets.

WARNING

%Gas leaks may occur in the system and result in a serious hazard. Gas leaks may

not be detected by smell alone. Gas suppliers recommend you purchase and install a UL approved gas detector. Install and use in accordance with the gas detector

manufacturer’s instructions. %To prevent staining or discoloration, clean appliance after each use. %Do not attempt to open or close the door or operate the oven until the door is properly

installed. %Never place fingers between the hinge and front oven frame. Hinge arms are spring

mounted. If accidentally hit, the hinge will slam shut against the oven frame and injure

your fingers.

CAUTION

%Wear gloves when cleaning the range to avoid injury or burns. %Do not use the oven for storing food or cookware. %To prevent damage to the oven door, do not attempt to open the door when Lock is

displayed. %Do not stand or place excessive weight on an open door. This could tip the range,

break the door, or injure the user. %Do not use delayed baking for highly perishable foods such as dairy products, pork,

poultry, or seafood.

ENGLISH

FLAMMABLE MATERIALS

WARNING

Be certain that all packing materials are removed from the appliance before operating. Keep plastic, clothes, paper, and other flammable materials away from parts of the appliance that may become hot.

%Do not store or use flammable material in the oven or near or on the cooktop. Flammable

materials include paper, plastic, pot holders, linens, wall coverings, curtains, and gasoline or other flammable vapors and liquids such as grease or cooking oil. These materials can be ignited when the oven and cooktop are in use.

%Wear proper apparel. Do not wear loose-fitting or hanging garments, which may ignite if

they contact hot surfaces, and cause severe burns. %Do not use the oven for drying clothes. Only use the oven for its intended purpose. %If a cabinet storage is provided directly above cooking surface, place items that are not

frequently used and can be safely stored in an area subjected to heat. Temperatures may

be unsafe for volatile items such as flammable liquids, cleaners or aerosol sprays.

IMPORTANT SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

CAUTION

%Always disconnect power from the appliance before servicing. %Do not use aluminum foil or any other material to line the oven bottom.

Improper installation of these liners may result in a risk of electric shock or fire. %Do not allow aluminum foil or the temperature probe to contact heating elements.

DEEP FAT FRYER

%Use extreme caution when moving or disposing of hot grease. %Always heat fat slowly, and watch as it heats. %If frying combinations of oils and fats, stir them together before heating. %Use a deep fat thermometer, if possible, to prevent overheating fat beyond the smoking

point. %Use the least possible amount of fat for effective shallow or deep-fat frying. Filling the pan

with too much fat can cause spillovers when food is added.

CHILD SAFETY

%Do not leave small children unattended near the oven.

WARNING

Do not leave children alone or unsupervised near the appliance when it is in use or is

still hot. Children should never be allowed to sit or stand on any part of the appliance as they could be injured or burned.

CAUTION

Do not store items of interest to children in cabinets above a range or on the back guard of a range – children climbing on the range to reach items could be seriously injured.

%Never let a child hang on the oven door. %Do not allow children to crawl into the oven. %Let hot utensils cool in a safe place, out of reach of small children. %Children should not be allowed to play with controls or other parts of the appliance.

IMPORTANT SAFETY INSTRUCTIONS

SURFACE BURNERS

WARNING

%Even if the top burner flame goes out, gas is still flowing to the burner until the knob is

turned to the Off position. If you smell gas, immediately open a window and ventilate the area for five minutes prior to using the burner. Do not leave the burners on unattended.

%Use proper pan size. Do not use pans that are unstable or that can be easily tipped.

Select cookware with flat bottoms large enough to cover burner grates. To avoid spillovers, make sure the cookware is large enough to contain the food properly. This will both save cleaning time and prevent hazardous accumulations of food, since heavy spattering or spillovers left on the range can ignite. Use pans with handles that can be easily grasped and remain cool.

CAUTION

%Be sure that all surface controls are set in the Off position prior to supplying gas to the

range.

%Never leave the surface burners unattended at high flame settings. Boilovers may

cause smoke and greasy spillovers that may ignite.

%Always turn the knobs to the Lite position when igniting the top burners and make sure

the burners have ignited.

%Control the top burner flame size so it does not extend beyond the edge of the

cookware. Excessive flame is hazardous.

%Only use dry pot holders- moist or damp pot holders on hot surfaces may result in

burns from steam. Do not let pot holders come near open flames when lifting cookware. Do not use towels or other bulky cloth items. Use a pot holder.

%If using glass cookware, make sure the cookware is designed for range-top cooking.

%To prevent burns from ignition of flammable materials and spillage, turn cookware handles

toward the side or back of the range without extending them over adjacent burners.

%Never leave any items on the cooktop. The hot air from the vent may ignite flammable

items and will increase pressure in closed containers, which may cause them to burst. %Carefully watch foods being fried at a high flame setting. %Always heat fat slowly, and watch as it heats. %If frying combinations of oils and fats, stir together before heating. %Use a deep fat thermometer if possible to prevent fat from heating beyond the smoking

point. %Use the least possible amount of fat for effective shallow or deep fat frying. Filling the

pan with too much fat can cause spillovers when food is added. %Do not cook foods directly on an open flame on the cooktop. %Foods for frying should be as dry as possible. Frost or moisture on foods can cause hot

fat to bubble up and spill over the sides of the pan. %Never try to move a pan of hot fat, especially a deep fryer. Wait until the fat is cool. %Do not place plastic items on the cooktop- they may melt if left too close to the vent. %Keep all plastics away from the surface burners. %To prevent burns, always be sure that the controls for all burners are in the Off position

and all grates are cool before attempting to remove them. %If you smell gas, turn off the gas to the range and call a qualified service technician.

Never use an open flame to locate a leak. %Always turn the knobs to the Off position before removing cookware. %Do not lift the cooktop. Lifting the cooktop can cause damage and improper operation

of the range.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

%If the range is located near a window, do not hang long curtains that could blow over

the surface burners and catch on fire. %Use care when cleaning the cooktop. The pointed metal ends on the electrodes could

cause injury. %Stand away from the range while frying. %Keep an eye on foods being fried at high or medium high heat settings.

GLASS-CERAMIC COOKING SURFACE

%Surface units may be hot even though they are dark in color. Areas near surface units may

become hot enough to cause burns. During and after use, DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS or let clothing or other flammable materials contact surface units or areas near units until they have had sufficient time to cool. This includes the Induction plate and the area above the oven door.

%Do not cook on a broken induction plate. If the induction plate is broken, cleaning

solutions and spillovers may penetrate the broken induction plate and create a risk of electric shock. Switch off the appliance to avoid the possibility of electric shock and

contact a qualified technician immediately. %Do not use the glass induction plate surface as a cutting board. %Do not place or store items that can melt or catch fire on the glass induction plate, even

when it is not being used. %Select pans that have flat bottoms large enough to cover the heating elements. %Glazed cookware. Only certain types of glass, glass-ceramic, ceramic, earthenware,

or other glazed cookware are suitable for range-top service without breaking due to the

sudden change in temperature. %Never cook directly on the glass. Always use cookware. %Always turn the surface units off before removing cookware. Do not rely on the pan

sensor.

WARNING

Do not leave fats or oils to heat unattended on the cooktop. Spillovers can result in a fire.

%The Induction plate is not intended to be operated by means of an external timer or

separate remote-control system. %Turn cookware handles inward so they don't extend over adjacent surface units.

This reduces the risk of burns, ignition of flammable materials, and spillage due to

unintentional contact with the cookware. %Immediately clean spills on the cooking area to prevent a tough cleaning chore later. %Some cleaners can produce dangerous fumes if applied to a hot surface. %Do not place metallic objects such as knives, forks, spoons, and lids on the Induction plate

surface, because they can get hot. %Always place the pan in the center of the surface unit you are cooking on. Never leave

surface units unattended at high heat settings. Proper contact of cookware to burner

also will improve efficiency. Boilovers cause smoking and greasy spills that may catch on

fire. %Clean induction plate with caution. Do not use sponges or cloth to wipe spills on a hot

cooking area. Use a proper metal scraper. If a wet sponge or cloth is used to wipe spills on

a hot cooking area, it can cause steam burns. Some cleaners can produce noxious fumes

if applied to a hot surface.

IMPORTANT SAFETY INSTRUCTIONS

%Do not turn surface units on before placing cookware. %Do not store heavy items above the Induction plate surface that could fall and damage it. %Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon

holders, or plastic wrappings or any other material on the range when it is in use. %Do not use a steel-wool pad or scrub pad or abrasive cleaning pads. They can scratch the

surface.

USING SOUS VIDE

CAUTION

%Use only food grade plastic bags or bags made from materials recommended by the

manufacturer for use in cooking. %Allow sous vide to cool before cleaning or draining the water bath. %Make sure the water level in the sous vide pan remains between the minimum and

maximum fill lines both before and after adding the food pouches. %Do not operate the sous vide module if the water level is not between these lines.

Doing so may result in electric shock or fire. %Do not touch the water in the sous vide module until it has cooled. Use tongs to take

out pouches in the water bath. Failure to follow this precaution can result in burns. %Allow the sous vide module to cool before touching any surfaces. Use an oven mitt

while operating the sous vide to avoid burns or other injury. %Don’t leave water in water bath after use. Allow the module to cool before draining the

bath and drying it with a clean cloth. %Do not place or store objects on the glass cover of the sous vide. Doing so can damage

the cover. %Only use pouches which are designed for vacuum sealing. %Vacuum sealing does not prevent food from spoiling. Refrigerate perishable food. %Sharp edges on food, such as bones or dried noodles, can puncture pouches during

vacuum sealing. Wrap sharp edges with paper towels or softer food items.

ENGLISH

FOOD PACKAGING AND STORAGE SAFETY INFORMATION

%Always wash your hands carefully with soap and water before and after handling food. %Keep all work surfaces and utensils clean and disinfected before and after packaging

foods.

%Temperature, moisture, acidity, and salt or sugar content of foods can influence the growth

of potentially harmful microorganisms in food.

%For safety, vacuum-sealed fresh (perishable) foods should be kept in the "safe zones":

cooled to 40°F/4°C or below or heated to 130°F/55°C or above.

%Vacuum-sealed pouches of cooked foods can be quick chilled by submerging them in ice

water (half ice/half water) for 30 to 60 minutes and then refrigerated for up to 48 hours or frozen for up to a year.

IMPORTANT SAFETY INSTRUCTIONS

USING STEAM FUNCTION

CAUTION

%Hot steam may cause scalding. %Don’t open the door and don't touch the vent holes while steam function is working. %Use care when opening the door. The hot air and steam that escape can cause burns

to hands, face and eyes. Let hot air or steam escape from the oven before opening the

door. %Steam may condense on the inside of the door. Do not wipe condensation off until the

door has cooled.

ENERGY SAVING TIPS

%Multiple-rack cooking saves time and energy. Whenever possible, cook foods requiring the

same cooking temperature together in one oven.

%For optimal performance and energy savings, follow the guides on page 37 for proper rack

and pan placements.

%Match the size of the cookware to the amount of food being cooked to save energy when

heating. Heating ½ quart of water requires more energy in a 3-quart pot than in a 1-quart pot.

%Match the size of the cooktop burner or element to the size of the cookware in use. Using

a large element for a small pan wastes heating energy, and the exposed surface of the element is a burn or fire hazard.

%Reduce energy use by cleaning light oven soils with the SpeedClean™ feature instead of

self-clean.

%Avoid opening the oven door more than necessary during use. This helps the oven

maintain temperature, prevents unnecessary heat loss, and saves on energy use.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY DURING USE

%Do not touch the oven racks while they are hot. %If a rack must be moved while the oven is hot, do not let the pot holder contact the hot

heating element in the oven.

%Use caution with the Timed Cook or Delayed Timed Cook features. Use the automatic

timer when cooking cured or frozen meats and most fruits and vegetables. Foods that can easily spoil, such as milk, eggs, fish, meat or poultry, should be chilled in the refrigerator first. Even when chilled, they should not stand in the oven for more than 1 hour before cooking begins, and should be removed promptly when cooking is complete. Eating

spoiled food can result in sickness from food poisoning. %Accessible parts may become hot when the grill is in use. %Do not place food or cookware on the bottom of the oven cavity. Doing so will cause

permanent damage to the oven bottom finish. %Do not use water on grease fires. Should an oven fire occur, leave the oven door closed

and turn the oven off. If the fire continues, throw baking soda on the fire or use a fire

extinguisher. Do not put water or flour on the fire. Flour may be explosive and water can

spread a grease fire and cause personal injury. %When disposing of the range, cut off the power cord and remove the door. %Do not make any attempt to operate the electric ignition oven during an electrical power

failure. %Pull the oven rack to the stop-lock position when loading and unloading food from the

oven. This helps prevent burns caused by touching hot surfaces of the door and oven

walls. %Do not use the oven if a heating element develops a glowing spot during use or shows

other signs of damage. A glowing spot indicates the heating element may fail and present

a potential burn, fire, or shock hazard. Turn the oven off immediately and have the heating

element replaced by a qualified service technician. %When using cooking or roasting bags in the oven, follow the manufacturer’s directions.

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

SAFETY WHEN CLEANING

%Open a window or turn on a ventilation fan or hood before self-cleaning. %If the oven is heavily soiled with oil, self-clean the oven before using the oven again. The

oil could cause a fire. %Wipe up heavy soil on the bottom of the oven before using the Self Clean function. %Do not use oven cleaners. Commercial oven cleaner or oven liner protective coating of

any kind should not be used in or around any part of the oven. %Never keep pet birds in the kitchen. The health of birds is extremely sensitive to the fumes

released during an oven self-clean cycle. Fumes may be harmful or fatal to birds. Move

birds to a well-ventilated room. %Clean in the self-clean cycle only parts listed in this manual. Before self-cleaning the oven,

remove the broiler pan, all oven racks, the meat probe and any utensils or food from the

oven. %Important Instruction. The oven displays an F error code and sounds three long beeps if it

malfunctions during the self-cleaning process. Switch off the electrical power to the main

fuse or breaker and have the oven serviced by a qualified technician. %It is normal for the cooktop of the range to become hot during a self-clean cycle. Do not

touch the cooktop during a self-clean cycle. %Never pour cold water over a hot oven for cleaning. Doing so may cause the oven to

malfunction. %Make sure oven lights are cool before cleaning. %Do not clean door gasket. The door gasket is essential for a good seal. Care should be

taken not to rub, damage, or move the gasket. %If there is a fire in the oven during self-clean, turn the oven off and wait for the fire to go

out. Do not force the door open. Introduction of fresh air at self-clean temperatures may

lead to a burst of flame from the oven. Failure to follow this instruction may result in severe

burns. %For your safety, do not use high-pressure water cleaners or steam jet cleaners to clean the

product.

COOK MEAT AND POULTRY THOROUGHLY

%To protect against food-borne illnesses, cook meat and poultry thoroughly. The USDA has

indicated the following as safe minimum internal temperatures for consumption:

%Ground meats: 160 °F

%All poultry: 165 °F

%Beef, veal, pork, or lamb: 145 °F

%Fish/seafood: 145 °F

PRODUCT OVERVIEW

Parts

Induction Cooktop

Gas Cooktop

Sous Vide

Cooktop controller

Left Oven Door

Right Oven Door

Accessories

Included Accessories

ENGLISH

Rating label model and serial number plate

Oven mode knob

Display Panel

Gasket

Rack Steam Feeder

Tank

Large gliding rack (3ea) Grid Broiler pan Meat probe (1ea) Owner’s manual

Large tray

(Large, 1set)

Small tray

(Small, 1set)

Small gliding rack

(3ea)

Spray bottle

(1ea)

Non-scratch scouring

pad (1ea)

Anti-tip kit

Anti-tip bracket Screws (6ea) Anchors (6ea) Template

LP nozzle conversion kit Sous Vide Module Accessories

Cooktop nozzles (5ea) Installation guide (1ea) Bath (1ea) Sous Vide Rack (1ea)

NOTE

%If accessories are missing, call 1-855-790-6655 or visit our website at : www.thesignaturekitchen.com

%For your safety and for extended product life, only use authorized components.

%The manufacturer is not responsible for product malfunction or accidents caused by the use of separately

purchased, unauthorized components or parts.

%The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

Black White Red

Conduit connection plate

Terminal block

Check and choose the

proper location

Pressure regulator

Install anti-tip device Level the range Connect electric range

240 V or 208 V

Plug in the power cordConnect the range to gas Engage the anti-tip device Test run

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Oven Range Models SKSDR480SIS

Description 48” Duel Fuel Pro Range

Electrical requirements 12.4 kW 120/240 VAC, 9.6 kW 120/208 VAC

Exterior Dimensions

Height to cooking surface 36" (91.4 cm)

Net weight 529.1 lb (240 kg)

Total capacity

/8" (W) x 35 7/64" (H) x 26 39/64" (D) (D with door closed)

121.6 cm (W) x 89.6 cm (H) x 67.6 cm (D) (D with door closed)

Right Oven : 5.2 cu.ft

Left Oven : 2.7 cu.ft

Total : 7.9 cu.ft

INSTALLATION

Before Installing the Range

WARNING

Tip - Over Hazard

A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place. Failure to follow these instructions can result in death or serious burns to children and adults.

To check that leveling leg is

inserted into anti-tip bracket,

grasp the top rear edge

of the range and carefully

attempt to tilt it forward.

Anti-tip bracket

Leveling leg

WARNING

ENGLISH

%Leveling legs must be extended lower than

wheels to prevent range from moving. This range is designed with wheels to make installation easier. During installation, make sure to extend the leveling legs until the wheels are lifted off the ground. Failure to do so can result in death or serious injury to children and adults.

If you did not receive an anti-tip bracket with your purchase, call 1-855-790-6655 (Signature Kitchen Suite) to receive one at no charge.

WARNING

%The information in this manual should be

followed exactly. Failure to do so may result in fire, electrical shock, property damage, personal injury, or death.

%Wear gloves during the installation

procedure. Failure to do so can result in bodily injury.

%Make sure no parts came loose during shipping.

In the Commonwealth of Massachusetts

%This product must be installed by a licensed plumber or gas fitter.

%When using ball type gas shut-off valves, they must be the T-handle type.

%When using a flexible gas connector, it must not exceed 3 feet in length.

NOTE

%Observe all governing codes and ordinances.

%Have the installer show you the location of the circuit breaker or fuse. Mark it for easy reference.

%As when using any appliance generating heat, follow basic safety precautions.

%Be sure your range is installed and grounded properly by a qualified installer or service technician

according to the installation instructions.

%Any adjustment and service should be performed only by qualified gas range installers or service

technicians.

INSTALLATION

Preparing for Installation

Tools Needed

Phillips screwdriver Flat-blade screwdriver

Level Open-end or

Pipe wrench (2)

(one for support)

adjustable wrench

Tape measure Gloves

/4" Nut driver Pliers

Drill Safety glasses Dolly

Parts Provided Parts not Provided

Template (1) Anti-tip bracket kit (1) 4-wire or 3-wire cord and

strain relief kit

(UL approved 40 or 50 AMP)

Strain relief

(For conduit

Installations only)

Anchor sleeves (6) Lag bolts (6) Leg cover (2 sets) Screws (7)

Front rail (1)

(Leg cover, Front rail)

Materials You May Need

%Gas line shut-off valve

%Pipe joint sealant that resists action of natural and LP gases

%Flexible metal appliance connector (

/4" or 1/2" NPT x 1/2" I.D.)

Never use an old connector when installing a new range.

%Flare union adapter for connection to gas supply line (

%Flare union adapter for connection to pressure regulator on range (

/4" or 1/2" NPT x 1/2" I.D.)

/2" NPT x 1/2" I.D.)

%Liquid leak detector or soapy water

%Lag bolt or

/2" O.D. sleeve anchor (for concrete floors only)

INSTALLATION

Ventilation Requirement

It is recommended that these ranges be installed in conjunction with a suitable overhead vent hood.

%Install a hood with at least 1200 CFM above a 48”

wide range.

%Install a hood with at least 600 CFM above a 30” or

36” range.

Due to the high heat capacity of this unit, particular attention should be paid to the hood and ductwork installation to assure it meets local building code.

WARNING

Do not install this product with an air curtain hood or other range hood that operates by blowing air down on the cooktop. This airflow may interfere with operation of the gas burners resulting in fire or explosion hazard.

See below for the minimum clearance from the cooking surface to any horizontal surface above the range. Failure to observe this clearance may result in a fire hazard.

%Installations without a hood require a 48"

minimum distance to any overhead combustible surface.

%Installations with custom hoods containing

exposed horizontal combustible surfaces require a hood with at least 600 CFM at least 36" above the cooking surface.

%For other hood installations, refer to the

installation instructions included with the hood for specific clearances.

Proper Location

CAUTION

%Avoid placing cabinets above the range. To

minimize the hazard caused by reaching over the open flames of operating burners, install a ventilation hood over the range that projects forward at least five inches beyond the front of the cabinets.

%Do not locate your range where it may be

subject to strong drafts. Any openings in the

floor or wall behind the range should be sealed. Make sure the openings around the base of the range that supply fresh air for combustion and ventilation are not blocked by carpeting or woodwork.

%This range is for indoor, household use

only.

%If the range is located near a window, do not

hang long curtains or paper blinds on that window.

%Make sure wall covering, countertop and

cabinets around the range can withstand the heat (up to 194 °F) generated by the range. Discoloration, delamination or melting

may occur. This range has been designed to comply with the maximum allowable wood cabinet temperature of 194 °F.

%Before installing the range in an area

covered with linoleum or other synthetic floor covering, make sure the floor covering can withstand temperatures of at least 160 °F(70°C).

%Use an insulated pad or

plywood under the range if installing the range over carpeting.

1/4

in. (0.64 cm)

ENGLISH

%The range is a free standing unit. If the unit is to be

placed adjacent to cabinets, the clearances shown

in “Install Clearance” are required. The same

clearances apply to island installations, except for

overhead cabinets, which must have a space wide

enough to accept the flared island hood.

%The range should not be recessed into the cabinets

beyond the edge of the front face of the oven. (see

“Product Dimensions and Clearances”)

%The maximum depth of overhead cabinets

installed on either side of the hood is 13”(330mm).

Wall cabinets must be 18” (457mm) above the

countertop.

%There is a 36'' (914 mm) minimum clearance

required between the top of the cooking surface

and the bottom of an unprotected cabinet. A 30''

(762 mm) clearance can be used when the bottom

of the wood or metal cabinet is protected by not

less than 1/4'' (6 mm) of a flame retardant material

covered with not less than No. 28 MSG sheet steel,

0.015'' (0.38 mm) thick stainless steel, 0.024'' (0.61

mm) aluminum, or 0.02'' (0.51 mm) thick copper.

When the floor covering ends at the front of the range, the area that the range will be installed on should be built up with plywood to the same level or higher than the floor covering. This will allow the range to be moved for cleaning and servicing, as well as provide proper air flow to the range.

NOTE

%All models require 12” minimum clearance to

a vertical combustible surface at the rear. If clearance is less than 12”, the entire surface of the back wall above and the full width of the range must be protected by a backsplash. The backsplash must be constructed of noncombustible material, such as metal, ceramic tile, brick, marble or other stone.

INSTALLATION

Install Clearance

47 7/8"

(1216 mm)

Width

35 7/64"

(895.7 mm)

36 45/64"

(932.3 mm)

Height

26 39/64"

(675.7 mm)

Depth to front edge

/16"

(26.8 mm)

Leg height

2 19/64"

(58.1 mm)

(94.7 mm)

Countertop to cooking surface

%The surface of the entire back wall above the

range and below the hood must be covered with a noncombustible material such as metal, ceramic tile, brick, marble or other stone.

/64"

Universal Utility Locations

WARNING

36"

(914.4 mm)

18"

(457 mm)

30"

(762 mm)

25" (635 mm)

24 1/2"

(622 mm)

(84 mm)

48"

(1219.2 mm)

Gas /Electrical Zone

/16"

16"

(406 mm)

7 1/2"

(190 mm)

7 5/8" (193 mm)

13" (330.2 mm)

5" (127 mm)

INSTALLATION

Product Dimensions and Clearances

To Front Edge

3.42" (87mm) Control Panel

24.4" (620mm)

Max. recess depth

ENGLISH

Depth

7.59" (193mm) Control Panel Height

12" Min. to combustibles or 0" to a non-combustible material above the cooking surface

0" Clearance to a back or side wall below the cooking surface

26.5" (673mm)

To Front of Door

29.1" (740mm)

To Front of Handle

50" (1270mm)

With Oven Door Open

INSTALLATION

Gas Supply

The range is designed to operate at a pressure of 5" of water column on natural gas or 10" of water column on LP.

Make sure you are supplying the range with the type of gas for which it is configured.

This range is convertible for use with natural or LP gas. When using this range with LP gas, conversion must be made by a qualified LP installer before attempting to operate the range.

For proper operation, the pressure of natural gas supplied to the regulator must be between 5" and 13" of water column.

For LP gas, the pressure supplied to the regulator must be between 10" and 13" of water column. When checking for correct operation of the regulator, the inlet pressure must be at least 1" more than the operating (manifold) pressure as given above.

The pressure regulator located at the inlet of the range must remain in the supply line regardless of which type of gas is being used.

A flexible metal appliance connector used to connect the range to the gas supply line should have an I.D.

/8" and a maximum length of 5 feet. In Canada, flexible connectors must be single wall metal connectors less than 6 feet in length.

Electrical Supply

Installation of the range must be planned so that the rough in of the terminal block for the receptacle or conduit connection will allow maximum clearance to the rear of the unit.

When the power supply cord or conduit is connected to the mating receptacle or terminal block cover, the combined connection should protrude no more than 2'' (51 mm) from the rear wall.

Installing the Range

Unpacking the Range

CAUTION

%You should use 2 or more people to move

and install the range. (Excessive Weight Hazard) Failure to do so can result in back or

other injury.

%Do not use the door handles to push or

pull the range during installation or when moving the range out for cleaning or service. Doing so can result in serious damage

to the door of the range.

Cut the packing straps. Lift the carton straight

up. Remove packing material, tape and any temporary labels from your range before using but leave the adhesive-backed foam layer over the brushed-metal surface, to protect the finish from scratches. Do not remove any warning-type labels, the model and serial number label, or the Tech Sheet that is located on the back of the range.

Remove the door(s). This will reduce the weight

of the range during installation.

The grates, burner heads, burner caps, trays

and oven racks must be removed to facilitate handling. Do not remove the griddle element.

NOTE

Canadian models have the power cord supplied with the range.

Power Cord & Receptacle

2" (51 mm) maximum

when plugged in

Junction Box & Conduit

2” (51 mm)

maximum

NOTE

Doors and passageways leading to the installation location require at least 32” opening. If the opening is less than 32”, the oven door(s) and control knobs must be removed.

INSTALLATION

Moving the Range

CAUTION

%Do not lift the range by the oven door’s handle,

as this may damage the door hinges and cause the door to fit incorrectly.

%Do not lift the appliance by the range’s control

panel.

%Rings, watches, and any other loose items

that may damage the unit or otherwise might become entangled with the unit should be removed.

%Hidden surfaces may have sharp edges. Use

caution when reaching behind or under the appliance.

%Do not use a hand truck or appliance dolly on

the back or front of the unit. Handle from the side only.

%Due to the weight, it is strongly recommended

that a furniture dolly with soft wheels or an air lift be used to move this unit. The weight must be supported uniformly across the bottom.

%All ranges are held to the pallet by (4) brackets

through a wood block

Carefully tilt the range from the side and insert a

dolly under the range to remove the range from the pallet. Use additional help as required to remove the product from the pallet. To prevent damage to the sides of the range, it will be necessary to pad the corners beneath the straps on the dolly.

Dolly Straps Below Oven

ENGLISH

Remove the two screws on each bracket that

secure the product to the pallet.

Remove both oven doors.

NOTE

%Instructions for removing the oven doors can

be found in the Maintenance section of this manual.

Transport the range on the furniture dolly close

to its final location, tip the range back to level, and carefully remove the dolly.

INSTALLATION

Installing the Anti-tip Device

WARNING

Tip - Over Hazard

To check that leveling leg is inserted into anti-tip bracket, grasp the top rear edge of the range and carefully attempt to tilt it forward.

Screw must enter wood or concrete

Anti-tip bracket

Wall plate

Leveling leg

Leveling the Range

Front Legs

Level the range by adjusting the leveling legs with a wrench. Extending the legs slightly may also make it easier to insert the rear leg into the anti-tip bracket.

Back Legs

To adjust the rear leveling legs, remove the 3 screws at the front of the vent trim and remove the trim.

Use an adjustable 7 mm box wrench to turn the rear leg extension rods at each corner.

Vent Trim

Locate the anti-tip bracket using the template.

An anti-tip bracket is packaged with the template. The instructions include necessary information to complete the installation. Read and follow the range installation instruction sheet (template).

WARNING

%A child or adult can tip the range and be killed.

%Install the anti-tip device to the structure and/

or the range. Verify the anti-tip device has been properly installed and engaged by following the instructions on this template.

%Engage the range to the anti-tip device

following the instructions on this template. Ensure the anti-tip device is reengaged when the range is moved by following the instructions on this template.

%Re-engage the anti-tip device if the range is

moved. Do not operate the range without the anti-tip device in place and engaged.

%See installation instructions for details.

%Failure to do so can result in death or serious

burns to children or adults.

Rear Leg Extension Rod

Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level.

First check direction

Then check direction

. If the level doesn’t show level

on the rack, adjust the leveling legs with a wrench.

INSTALLATION

Installing the Leg Cover

Remove the plastic covers from the stainless

steel leg covers.

Slide each small leg cover inside a larger leg

cover. Cutouts should face up and both covers should be open at the back.

Use the assembled covers to conceal the front

leveling legs.

Place the outer covers on the floor and slide the

inner covers up until the holes at the top front snap over the dimples on the flanges on the bottom of the range.

Installing Front Rail

Remove the plastic film from the stainless steel

front rail.

Insert the front rail onto the flange below the

oven door, aligning the holes in the top of the rail with the holes in the flange.

Front Rail

Flange

Use the 3 screws provided to secure the front

rail to the flange.

ENGLISH

Dimples

Insert the provided screws through the holes

in the leg cover assemblies to secure them in place.

INSTALLATION

Connecting the Range to Gas

Shut off the range gas supply valve before removing the old range and leave it off until the new hook-up has been completed.

Because hard piping restricts movement of the range, a CSA International-certified flexible metal appliance connector should be used unless local codes require a hard-piped connection.

A manual valve must be installed in an accessible location in the gas piping external to the appliance for the purpose of turning on or shutting off gas to the appliance.

Never reuse an old connector when installing a new range.

To protect against gas leaks, use a qualified pipe joint sealant on all external threads.

An inlet pipe is set on the left rear of this

appliance. Hook up a gas hose that has 1/2" NPT internal thread to the inlet pipe using a wrench.

Apply sealing compound or Teflon tape at the

connection.

When all connections have been made, be sure

all range controls are in the Off position and turn on the main gas supply valve. Gas leaks may occur in your system and create a hazard. Gas leaks may not be detected by smell alone.

Check all gas connection joints and fittings for leaks with a non-corrosive leak detection fluid, then wipe off.

Gas suppliers recommend you purchase and install a UL approved gas detector. Install and use in accordance with the installation instructions.

Flexible Connector Hookup

Adapter

Pressure regulator

Installer: Inform the consumer of the location of the gas shutoff valve

Pressure Regulator Position

/2"

/2" or 3/4" Gas

pipe

Pressure Regulator

Gas Flow into Range

Flex connector (6 ft. max.)

Adapter

Gas shut-off valve

WARNING

%Do not use a flame to check for gas leaks.

%Isolate the range from the gas supply system

by closing its individual shut-off valve during any pressure testing of the gas supply system at test pressures equal to or less than (3.5 kPa).

/2" psig

INSTALLATION

Connecting Electricity

Electrical Requirements

This appliance must be installed and grounded on a branch circuit by a qualified technician in accordance with the National Electrical Code ANSI/NFPA NO. 70

- latest edition.

All wiring should conform to local and NEC codes. This range requires a single-phase, 3 wire, A.C 120/208 V or 120/240 V 60 Hz electrical system. Use only a 3-conductor or a 4-conductor UL -listed range cord with closed-loop terminals, open-end spade lugs with upturned ends or similar termination. Do not install the power cord without a strain relief.

A range cord rated at 40 amps with 120/208 or 120/240 minimum volt range is required. If a 50 amp range cord is used, it should be marked for use with

/8" diameter connection openings. This appliance may be connected by means of a conduit or power cord. If a conduit is being used, go to page 28 for

3 wire conduit connections or 4 wire conduit connections.

WARNING

%Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack

in the line so that the range can be moved if servicing is ever necessary.

%The power supply cord and plug should not

be modified. If the plug will not fit the outlet, have a proper outlet Installed by a qualified electrician.

%Using an extension cord to connect the

power is prohibited. Connect the power cord and plug directly.

%Electrical ground is required on this

appliance.

%Make sure that the power cord is not pinched

by the range or heavy objects. Failure to do so can result in serious burns or electrical shock.

%Do not use a damaged power plug, power

cord, or loose power outlet.

%Do not put a fuse in a neutral or ground

circuit.

%Do not connect the ground wire to plastic

plumbing lines, gas lines, or hot water pipes.

Specified power-supply-cord kit rating

Range rating, watts

Specified

rating of

power

120/240

volts

3-wire

8,750 16,500

16,501 22,500

120/208

volts

3-wire

7,801 12,500

12,501 18,500

supply-

cord kit,

amperes

40 or 50A

3, 4 - Wire Electrical Wall Receptacle

4 Wire receptacle (14-50R)

3 Wire receptacle (10-50R)

Diameter

(inches) of range

connection

opening

Power

cord

/8"

/4"

Conduit

/8"

ENGLISH

INSTALLATION

Connecting the Power Cord

The rear access cover must be removed. Loosen the two screws with a screwdriver. The terminal block will then be accessible.

Access cover

Use the cord/conduit connection plate to install the power cord or conduit. Leave the connection plate as installed for power cord installations. Remove the connection plate for conduit installations and use the smaller 1 13/8 in. (3.5 cm) power cord hole.

For power cord installations, hook the strain relief over the 13/8 in. (3.5 cm) power cord hole located below the rear of the oven. Insert the power cord through the strain relief and tighten it.

For conduit installations, insert the conduit strain relief in the 11/8 in. (2.8 cm) conduit hole. Then install the conduit through the body of the strain relief and fasten the strain relief with its ring.

/8 in. (2.8 cm) conduit hole instead of the

11/8"

(2.8 cm) Conduit

13/8"

(3.5 cm) Cord

Remove the conduit connection plate

Power cord

Assembling power cord strain relief at the 1

Conduit connection plate

/8" opening

3-Wire Connection: Power Cord

WARNING

%The middle (neutral or ground) wire, which

is white, of a 3-wire power cord or a 3-wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block.

Failure to do so can result in electrical shock, severe personal injury or death.

Installing the Power Cord

For power cord installations, hook the strain relief over the power cord hole (1 rear of the oven. Insert the power cord through the strain relief and tighten the strain relief.

Do not install the power cord without a strain relief.

Remove the lower 3 screws from the terminal

block and retain them.

Insert one of the screws through each power

cord terminal ring and into the lower terminals of the terminal block. Make sure that the center (neutral) wire, which is white, is connected to the center lower position of the terminal block.

Tighten the 3 screws securely into the terminal

block. Do not remove the ground strap connections.

3-Wire Connection

Black White Red

/8") located below the

Terminal block

Ring

Body

Assembling conduit cord strain relief at the 1

Cord/ Conduit connection plate

Conduit

/8" opening

Conduit connection plate

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

+ 64 hidden pages