LG WT-H756TH User Manual
roduct Features
START
WASHING
AUTO
POWER
OFF
SENSING
Laundry Sensor
Water Level Sensor
SETTING
Optimum
Washing
condition
P
Washer doesn't operate while the lid is open. If the lid is open during the wash,
rinse or spin cycles, the operation stops for safety.
The washing machine may during normal usage cary out an operational test.
This is a programed check to ensure reliability and does not indicate a fault.
I sensor
•
The sensor automatically detects the quantity of a Detergent selected by a user and the
temperature and the quality of water to determine the best washing algorithm for washing
and rinsing, which will give the best washing effect.
FUZZY logic control
•
A built-in load sensor automatically detects the laundry load and a microprocessor
optimizes washing conditions such as ideal WATER LEVEL and washing time.
•
Advanced technology is built into the Electronic Control System which
ensures the best washing result.
3 Type Washing Methods (Direct Drive System)
•
3 actions are used to create the best washing results with minimal tangling.
Pulsator rotates
with the cloth
ATTENTION
: Be sure to remove the product from the carton base,
otherwise the machine will not be able to operate properly.
Drum rotates Water pours down
and circultes
4
afety Information
S
This booklet is divided into 2 parts : Warning and Caution.
Introduction
WATER
HEATER
SAFETY
Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
Warning
Caution
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
: Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
Warning
• Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
PROPER
INSTALLATION
Caution
• The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or
deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may
cause electric shock.
• Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
afety Information
5
S
YOUR
LAUNDRY
AREA
WHEN USING
THE WASHER
Warning
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger
explosion or fire.
•
Close supervision is necessary if this appliance is used by or near children or
infirm persons. Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
Caution
Introduction
•
Use this appliance only for its intended purpose as described in this OwnerÕs Manual.
•
The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturerÕs wash and care instructions.
•
To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
•
Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors
may induce electricity leakage, further resulting in electric shock or fire.
•
If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
6
afety Information
S
WHEN USING
THE WASHER
Introduction
WHEN NOT
IN USE
Warning
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or
deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
Caution
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically
recommended in this Owner’s Manual, or in published user-repair instructions
that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a
cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire
due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any
part of the washing machine.
It will cause short circuit and electric shock.
dentification of Parts
Height adjustment
plate
Inlet hose
Drain hose
2 Pieces
1 Each for cold and
hot water
operating the
washing machine.
is hung up before
Check if the drain hose
DRAIN HOSE
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.
LINT FILTER
Clean regularly to stop
linting on the clothes
load.
BASE
WASHING WINGS
Vertical movement of
washing action can be
operated when a sufficient
amount of laundry is
deposited.
Set the proper water level,
an excessive amount of
water may increase
entanglement of laundry.
HOT WATER SUPPLY
HOSE
COLD WATER SUPPLY
HOSE
Make sure the water
does not leak.
Softner will automatically
flow into the tub.
SOFTENER
INLET
INLET HOLE FOR
BLEACH
LEVELLING LEGS
Use to level the washing
machine for correct balance
& spin operation.
POWDER DETERGENT
BOX FOR DELAYED
WASHING
TUB
START/PAUSE
BUTTON
Use to start or stop the
washing machine
temporarily.
7
I
Body
Introduction
Accessories
Wlthin 50mm
Hose Guide
Drain Hose
0.9~1.2m
8
TAP
SEALING
WASHER
TAP
END
TWIST
(Fig. 2)
INLET
HOSE
(Fig. 1)
MACHINE
END
SEALING
WASHER
INLET
VALVE
nstallation
I
Connect the drain hose
Introduction
❏ NOTE :
•
•
•
•
Flooding drainage
•
Connect the inlet hose
Connect the drain hose to the outlet
of the drain pump located at the rear
of the washing machine.
Never lay down the drain hose, as water will be discharged.
Be sure the drain hose is properly routed so it will not kink or lift from the sink.
To prevent syphoning,the drain hose should not extend more than 50 mm from
the end of the hose guide.
The discharge height should be approximately 0.9~1.2m from the floor.
“Washing machine is to be connected to the water mains using new hose-sets and that old hose-sets should not
be reused ”
Your machine requires a floor drainage slope (or hole) that will SAFELY DISPOSE of the FULL FLOW of any water
that may leak out should the machine malfunction.
It is therefore the OWNER'S RESPONSIBILITY to make sure this machine is installed in an area with a drain hole (or
slope) that will prevent any possibility of water damage to floor coverings or property.
Attach the clip to the drain hose.
And then push it toward the body of
the washing machine as indicated by
the arrow.
Place the hose guide over the
laundry tub or the stand pipe.
Do not use an extension hose.
•
Check that sealing washers are firmly seated.
•
Attach the curved end of the hose to the inlet valve of the washing
machine ; Tighten the coupling nuts securely by hand. (Fig.1)
•
Attach the straight end of the hose to the tap.
Tighten the coupling nuts securely by hand. (Fig.2)
•
Another hose can be attached to hot inlet valve and tap.
•
Turn on the taps and check for leaks. Tighten the coupling nuts firmly
if there is any leakage. If water pressure is strong, close the water tap
completely then open it slightly.
CAUTION
Do not install the washer where it is directly exposed to sunlight, wind, rain etc.
Plug the power cord of this washer into a properly installed standard power point that is switched &
earthed.
Your machine requires a floor drainage slope (or hole) that will SAFELY DISPOSE of the FULL
FLOW of any water that may leak out should the machine malfunction. It is therefore the OWNER'S
RESPONSIBILITY to make sure this machine is installed in an area with a drain hole (or slope) that
will prevent any possibility of water damage to floor coverings or property.
Permissible water temperature : Max 70°C (160°F)
Permissible water pressure : Max 80psi (550kpa, 8kg/cm
If water temperature &pressure is greater than above, it may cause damage to the machine. If you
have uncontrolled water temperature & pressure you should fit a temperature & pressure relief valve
to ensure that water temperature & water pressure remains within the safe limits. Consult a plumber
or electrician if you are unable to adjust water temperature and pressure.
Do not over tighten the coupling nuts with a tool. Inlets are plastic : Do not strip or crossthread.
2
), Min 4psi (30kpa, 0.3kg/cm2)
nstallation
10cm
A.L SPINCLE
UP
DOWN
1 plate used 2 plates used 3 plates used 4 plates used
9
I
CAUTION
Install the washing machine on a flat and firm surface.
•
Install the washing machine on a level and firm surface.
•
Keep the washing machine more than 10cm from the wall to prevent vibration noise during spinning.
•
The base opening must not be obstructed by carpeting when the washing
machine is installed on a carpeted floor.
•
Wooden floors may need reinforcing to prevent the normal vibration which occurs with an unbalanced load.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits. Check the specification page of
this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any
of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if
its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the
cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the appliance.
Introduction
•
CAUTION
If the washer is installed on a uneven,weak or tilted floor causing excessive vibration, spin failure
UE " error can happen to it.
or "
It must be placed on a firm and level floor to prevent spin failure.
•
If the appliance is supplied from a cord extension set or electrical portable outlet device the core
extension set or electrical portable outlet device should be positioned so it is not subject to
splashing or ingress of moisture.
Level the washing machine
❏ Check the level of the washing machine using a
spirit level on the side of the washing cabinet
❏ You can check the level also by visually lining up the
washer with the fills, adjacent walls or cabinets.
❏ You can level the washer using the A.L spindle fitted to the cabinet.
•
Screw the A.L SPINDLE legs up or down as required.
•
Additional height adjustment plates are provided in the accessory bag. These fit under A.L SPINDLE if required
to allow for greater adjustment of the legs.
•
When washing machine does not even out, turn A.L SPINDLE
right or left to be level.
•
Should the height adjustment exceed the maximum
allowed by the A.L SPINDLE, place height
adjustment plats provided under
the legs as shown in the
diagram.
Loading...