OWNER’S MANUAL
Wall
Mounting
Bracket
Please read this manual carefully before operating the your set and retain it for future reference.
WM-L640V
WM-P640V
|
P/NO : MFL68006802(1503-REV00) |
*MFL68006802* |
Printed in Korea |
www.lg.com |
<![endif]>ENGLISH
2 CONTENTS
CONTENTS
3 SAFETY INSTRUCTIONS
4Precaution in Installation
4Precaution in Movement
5PRODUCT COMPOSITION
6INSTALLATION GUIDE
6Preparing the Multi-Vision to Be Attached to Product
7Fixing the Product to Wall
10 Connecting Multiple Products
12 Mounting a Multi-Vision to the Product
14 TRANSFORMATION OF PRODUCT
14 Reassembly for 55-in Multi-Vision
16 PRODUCT OPERATION
18 PRODUCT SPECIFICATIONS
SAFETY INSTRUCTIONS 3
SAFETY INSTRUCTIONS
If you are a professional installer, please read this manual carefully before installing the product.
After installing the product according to the manual, ensure that the user also reads the manual carefully.
After reading the manual, please keep it handy for future reference.
WARNNING
The product should be installed by a qualified professional specified by the retail store.
Installing the product without a qualified professional is dangerous and may cause personal injury.
When moving or replacing the product after installation, contact a qualified installer specified by the retail store.
Installation or movement of the product must be carried out by a skilled professional. If unqualified persons move and install the product, it may cause safety issues.
The product should be installed where its weight can be fully supported.
If the product is installed on a weak surface, the product may fall, causing injury.
Do not hang on this product or apply any shock to it.
The product may fall and cause injury.
CAUTION
Follow the instructions in the manual to properly install this product.
If you do not follow the instructions, the product may be installed incorrectly and cause serious injury or damage to the product.
During installation, check whether the wall is strong enough to hold the product and use the anchors and screws provided.
If you use anchors and screws that are not specified by the manufacturer, they may not hold the weight of the product, causing safety issues.
Do not clean the product with wet towels and do not place a heater or humidifier underneath it.
Moisture permeating into the product, including through steam and heat, may result in a fire, electric shock or damage to the product.
Make sure that the power cord is removed from the outlet before installing the product.
Otherwise, it may cause an electric shock or fire.
To install or adjust the height of the product, two or more people are needed.
If you try to install or move the product alone, it may fall, causing injury or damage to the product.
When drilling holes into the wall, make sure you use a drill and drill bit with the specified diameter. Ensure that you also follow the instructions regarding the depth of the holes.
Otherwise, the product may be installed incorrectly and cause safety issues.
Keep this product away from sprinklers, sensors, high-tension wires, and power sources. Do not install it in a location where vibrations or impact shocks are likely to occur.
Wear working gloves when installing the product. Do not use bare hands.
Otherwise, it may cause personal injury.
<![endif]>ENGLISH
<![endif]>ENGLISH
4 SAFETY INSTRUCTIONS
Precaution in Installation
WARNNING
Check the wall material and thickness of the finishing material.
You can use the anchors and screws provided with the TV set for the wall made with concrete, lightweight concrete, soft fieldstone, hard fieldstone, brick or cellular block.
Do not mount the device on walls made with plaster board or medium-density fiberboard (MDF). In this case, the anchor and screws must be inserted into the concrete behind the finish. If there is no concrete on the other side, then you must install a separate hanger first to fix the anchors and bolts to.
When installing it on a wall not specified in this manual, make sure each fixing point withstands an uplifting load of 70 kgf (686 N) and a shearing load of 100 kgf (980 N) or more.
Precaution in Movement
WARNNING
The weight of the Multi-Vision installed on the product must be equal to or less than 40 kgf.
Precautions when mounting Multi-Visions
When installing multiple Multi-Visions, be careful to avoid vertical and horizontal impacts between the Multi-Visions. Strong shocks may cause the MultiVisions to malfunction.
When transporting the product, check whether the safety screws (black) are fastened to the location illustrated in the figure below. If the safety screws (black) are not fastened, it may result in personal injury due to an unexpected movement of the product.
PRODUCT COMPOSITION 5
PRODUCT COMPOSITION
Please check whether all the components are included in the box before using the product. If there are any missing components, contact the retailer where you purchased the product. Note that the accessories may look different from those shown here.
<![endif]>ENGLISH
Wall Mounting Anchor, 12 EA |
Wall Mounting Bracket |
Wall Mounting Bracket |
|
Fixing Screw |
Fixing Screw |
|
(Used for fixing to wall) |
(Used for inter-product fixing) |
|
( 5 x L65) 12 EA |
(M4 x L10) 4 EA |
Guide Spacer, 4 EA |
Guide Spacer Fixing |
Safety Clip, 2 EA |
Owner's Manual |
|
Screw |
|
|
|
(M6 x L40) 4 EA |
|
|
CAUTION
Always use genuine components to ensure safety and product performance.
The product warranty will not cover damage or injury caused by the use of counterfeit components.
NOTE
The accessories supplied with your product may vary depending on the model.
Without prior notice, all information and specifications in this manual are subject to change to improve the performance of the product.
<![endif]>ENGLISH
6 INSTALLATION GUIDE
INSTALLATION GUIDE
Preparing the Multi-Vision to Be Attached to Product
-The picture may differ from the actual product.
1Place the multi-vision on a table with its screen facing downward.
- Make sure that you place it on soft clothing or a cushion on the flat surface
2Remove any screws that have been installed on the fixing area of the multi-vision wall mounting bracket.
3Check if the guide spacer is at the maximum value.
4Place the guide spacers over the screw holes on the Multi-Vision. Tighten the guide spacers with the guide spacer fixing screws (M6 x L40).
5Turn the screw until the gap between the guide spacer and the Multi-Vision has about 1 mm remaining.
Maximum
Multi-vision |
Guide Spacer |
|
1 mm |
Guide Spacer Screw
Guide Spacer
Guide Spacer Fixing Screw
NOTE
If the screws are not fully tightened when you fix the guide spacers, check the length of the screws and refer to the technical service manual.
|
INSTALLATION GUIDE 7 |
|
|
|
|
Fixing the Product to Wall |
4 Place the wall mounting bracket close to the |
|
|
wall along the hole. |
1On the position where the wall mounting anchor will be fixed, drill a hole with a depth of between 80 mm - 100 mm using a drill bit Ф 8 mm.
- Use the Ф 8 mm drill bit for concrete and a hammer (impact) drill.
Wall Mounting Anchor
Wall Drill
5 Insert the wall mounting screw into the hole and tighten it.
2 Clean out the drilled hole.
Wall Mounting Screw
Hole
3Insert the wall mount anchor to the hole (using a hammer).
Wall Mounting Anchor
<![endif]>ENGLISH
<![endif]>ENGLISH
8 INSTALLATION GUIDE
Install the product on the wall using the fixing screws for the wall mounting bracket. Install the product with the arrow marked on it facing upward.
WM-L640V
INSTALLATION GUIDE |
9 |
WM-P640V
<![if ! IE]><![endif]>ENGLISH
<![endif]>ENGLISH
10 INSTALLATION GUIDE
Connecting Multiple Products
- The picture may differ from the actual product.
1 Connect the fixing screws for wall mounting bracket on the up, down, left and right side.
2 Insert the fixing screws to the holes as shown in the figure and turn them.
WM-L640V
INSTALLATION GUIDE 11
WM-P640V
<![if ! IE]><![endif]>ENGLISH
<![endif]>ENGLISH
12 INSTALLATION GUIDE
Mounting a Multi-Vision to the Product
- The picture may differ from the actual product. Please install in the following order:
1Check if the up/down adjustment piece is located at the uppermost position.
2Remove the two safety screws. If the safety screw is fastened, the product cannot be moved to the left or right.
3As shown in the figure, hang the multi-vision combined to the guide spacer using the holes on the product.
4Align the height of the product and the Multi-Vision by adjusting the up/down adjustment piece downwards.
-If you install multiple products, accurately align the products and the Multi-Vision from bottom to top. Otherwise, installing products that will be located at the top will be difficult.
5Fit a safety clip to prevent the installed multi-vision from coming loose. It should be inserted to the guide spacer hole at the bottom of both sides.
WM-L640V |
2 |
Up/Down Adjustment Screw |
|
||
|
Safety Screw (black) |
|
1 3
4
5
Product Multi-Vision