LG WM2701HV/00 Owner’s Manual
WASING Ac E
USER'SGUIDE&
INSTALLATIONINSTRUCTIONS
Before beginning installation, read these
instructions carefully. Thiswll simplify installation andensure that the
washer is installed correctly and safely.Leavethese instructions near
the washer after installation for future reference.
[AvADOA
GUIADELUSUARIOE
INSTRUcclONESDEINSTALAclON
Antesde comenzar iainstaiacion, lea atentamente estas instruccio-
nes.Esto simplificara la instalacion y asegurara que la lavadora esta
instalada en forma correcta y segura. Conserve estas instrucciones
cerca de la lavadora luego de la instalacion parafuturas consultas.
TOcontact LG Electronics, 24 hours a day,
7 days a week:
1-800-243-0000
Or visit us on the Web at: us.lge.com
NOmero telef6nico de LG Electronics, las 24 horas
del dia, 7 dias a la semana:
1-800-243-0000
O visitenos en la Web en: us.Lge.com
To contact LG Electronics, 24 hours a day,
7 days a week:
1-888-LGCANADA
Or visit us on the Web at: ca.lge.com
Pour contacter LG Electronics, 24 heures par jour,
7 jours par semaine :
1-888-LGCANADA
Ou visitez notre site Web b,I'adresse : ca.lge.com
INEA Lave
GUIDEDE['UTILISATEUP,ET
DIREcTIvESD'INSTALLATION
Avant de commencer a installer votre machine alaver,iisez at-
tentivement cesinstructions. Celasimplifiera votre installation
et assurera que la machine a laver est installee correctement et
en toute securite. Conservezcesinstructions a proximite de la
machine a laver apres son installation, pour reference future.
rgodel/rgodelo/rgodele
WM2701 H*
Designed specially to use only
HE (High-Efficiency) detergent
Dise_ada especificamente para usar con
el detergente tipo HE (Alta efidencia)
Sp¢cialement conqu pour
utilisation avec un detergent haute ef-
ficacit¢ uniquement
Protocol P172
Sanitization Performance of Residential and
Commercial, Family Sized Clothes Washers
Protocolo P172
Ejecucion de Saneamiento en lazona
residencial y comerdal, lavodoras del uso del hogar
Protocole P172
Performance en maticre d'assainissement des laveuses
rcsidentielles et commerciales de grande taille
P/No. MFL31245168
INT 0 UCTI N
_MPORTANT SAFETY _NSTRUCT_ONS
Basic Safety Precautions .................................. 3-6
PARTS AND FEATURES
Special Features ..................................................... 7
Key Parts and Components ................................... 8
_NSTALLAT_ON _NSTRUCT_ONS
Choose the Proper Location .................................. 9
Clearances ............................................................. 9
Flooring ................................................................ 10
Installations With Optional Pedestal Base
or Stacking Kit ...................................................... 10
Unpacking and Removing Shipping Bolts ........... 11
Connecting the Water Lines ................................. 12
Connecting the Drain Line .................................... 13
Leveling the Washer ............................................. 14
HOW TO USE
Sorting Wash Loads ............................................. 15
Selecting Detergent .............................................. 16
About the Dispenser ............................................. 16
Loading the Dispenser ......................................... 17
Control Panel Features ......................................... 18
Cycle Guide .......................................................... 19
The LED Display ................................................... 20
Operating the Washer .......................................... 21
Cycle Setting Buttons .......................................... 22
Cycle Option Buttons .................................... 23-24
Speciat Functions ................................................. 25
CARE AND CLEAN,NO
Regular Cleaning ............................................ 26-27
Cleaning the Washer ............................................ 28
Maintenance ................................................... 29-30
TROUBLESHOOT_NO
Normal Sounds You May Hear ............................. 31
Before Calling for Service ............................... 31-33
YOU
Congratulations on your purchase
and welcome to the LG family.
Your new LG washing machine
combines the most advanced
washing technology with simple
operation and high efficiency.
By following the operating and care
instructions in this manual, your
washer will provide you with many
years of reliable service.
Product Registration information
Modeh
Seriam Number:
Date of Purchase:
The model and serial number can be located on
the rating plate on the front of the washer.
SPECiFiCATiONS/OPTiONAL ACCESSORIES
Key Dimensions and Specifications ..................... 34
Optional Accessories ........................................... 34
WARRANTY ..............................................35-36
I 0 TANTSAFETYINST UcTIONS
RSAD ALL iNSTRUCTiONS BEFORS USE
_WARNING Foryo.rsafety,theinformationinthisman.alre.stbe
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
Your Safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This isthe safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:
_E)A_G_R: You can be killed or seriously injured if you don't immediately follow instructions.
_WARN|NG-" You can be killed or seriously injured ifyou don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of
injury, and tell you what can happen if the instructions are not followed.
5
+NSTL!cT! NS
READ ALL
_WA_|_I_G For your safety, the information in this manuaU must be
followed to minimize the risk of fire or e×pUosion, eUectric shock, or to prevent
property damage, personaU injury, or Uoss of Uife.
BASIC SAFETY PRECAUTIONS
_!_t__G: TOreduce the risk of fire, e,ectfic shock, or injury to persons when using this
appBiance, follow basic precautions, incBuding the following.
+ Before use, the washer must be properly installed as
described in this manual.
+ Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other flammable
or explosive substances, as they give off vapors that
could ignite or explode.
+ Do not add gasoline, dry cleaning solvents, or other
flammable or explosive substances to the wash
water. These substances give off vapors that could
ignite or explode.
+ Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washer,
turn on all hot water faucets and let the water flow
from each for several minutes. This will release any
accumulated hydrogen gas. As the gas is flammable,
do not smoke or use an open flame during this time.
+ Do not allow children to play on or in the washer.
Close supervision of children is necessary when the
washer is used near children.
+ Before the washer is removed from service or
discarded, remove the door to prevent children from
climbing inside.
+ Do not install or store the washer where it will be
exposed to the weather or freezing temperatures.
+ Do not tamper with controls.
+ Do not repair or replace any part of the washer or
attempt any servicing other than as described in this
manual. We strongly recommend that any service be
performed by a qualified individual.
+See Installation Instructions for grounding
requirements.
+ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
+ Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
+ Use fabric softeners or products to eliminate static
only as recommended by the manufacturer.
+This washer is not designed for maritime use or for
mobile installations such as in RVs, aircraft, etc.
+Turn off the water taps and unplug the washer if the
machine is to be left for an extended period of time,
such as during vacations.
+ Packaging material can be dangerous for children.
There is a risk of suffocatio!! Keep all packaging
from children.
+Always check the inside of the washer for foreign
objects before loading laundry. Keep the door closed
when not in use.
GROUNDING iNSTRUCTiONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least resistance for electric current. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
_WA__G: improper connection of the equipment-grounding conductor can result in risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the
appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the
outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause
serious injury, fire, electrical shock, or death.
4
I 0 TANTSAFETYINST UcTIONS
RSAD ALL iNSTRUCTiONS BEFORS USE
WARNING Foryo.rsafety,theinformationinthismanualmustbe
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
SAFETY iNSTRUCTiONS FOR iNSTALLATiON
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this
appliance, follow basic precautions, including the following.
• Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures. Installation
instructions are packed in the washer for installer's
reference. Ifthe washer is moved to a new location,
have it checked and reinstalled by aqualified service
person. Failure to follow this warning can cause
serious injury, fire, electrical shock, or death.
• Do not, under any circumstances cut or remove
the third (ground) prong from the power cord.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
• For personal safety, this appliance must be
properly grounded. Failure to follow this warning
can cause serious injury, fire, electrical shock,
or death.
• The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock hazard from
this appliance.
• This washer must be plugged into a 120VAC, 60Hz
grounded outlet. Failure to follow this warning can
cause serious injury, fire, electrical shock, or death.
• Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded. Failure to follow this warning
can cause serious injury, fire, electrical shock,
or death.
• Where a standard 2=prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a properly
grounded 3-prong wall outlet. Failure to follow
this warning can cause serious injury, fire, electrical
shock, or death.
• Do not install on carpet. Install washer on a solid
floor. Failure to follow this warning can cause serious
leak damage.
Do not remove ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3=prong outlet. Failure to follow these warnings can
cause serious injury, fire, electrical shock, or death.
• The washer should always be plugged into its
own individual electrical outlet which has a
voltage rating that matches the rating plate. This
provides the best performance and also prevents
overloading house wiring circuits which could cause
a fire hazard from overheated wires.
• Never unplug your washer by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet. Failure to follow this warning can
cause serious injury, fire, electrical shock, or death.
• Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end. Failure
to follow this warning can cause serious injury, fire,
electrical shock, or death.
When installing or moving the washer, be careful
not to pinch, crush, or damage the power cord.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
The washer must be installed and electrically
grounded by a qualified service person in
accordance with local codes to prevent shock
hazard and assure stability during operation.
Washer is heavy. Two or more people may be
need to install and move the appliance. Failure to
do so can result in back or other injury.
Store and install the washer where it will not
be exposed to temperatures below freezing or
exposed to outdoor weather conditions. Failure to
follow this warning can cause serious leak damage.
Do not install the washer in humid spaces to
reduce the risk of electric shock. Failure to follow
this warning can cause serious injury, fire, electrical
shock, or death.
5
INST L!cT! NS
READ ALL
WARNING yours ety,thein or,,, tioninthis m stbe
followed to minimize the risk of fire or expUosion, eUectric shock, or to prevent
property damage, personaU injury, or Uoss of Uife.
SAFETY iNSTRUCTiONS FOR USE, CARE AND CLEANING, AND DISPOSAL
_WA__f_G: To reduce the risk of fire, e,ectric shock, or injury to persons when using this
appBiance, follow basic precautions, including the following.
• Unplug the washer before cleaning to avoid the
risk of electric shock.
• Never use harsh chemicals, abrasive cleaners,
or somvents to dean the washer. They will
damage the finish.
Do not put oily or greasy rags or clothing on
top of the washer. These substances give off
vapors that could ignite the materials.
Do not wash items that are soimed with
vegetabme or cooking oiL These items may
contain some oil after laundering. Due to the
remaining oil, the fabric may smoke or catch
fire by itself.
Disconnect this appliance from the
power supply before attempting any user
maintenance. Turning the controms to the OFF
position does not disconnect this appliance
from the power suppmy. Failure to follow this
warning can cause serious injury, fire, electrical
shock, or death.
Do not combine laundry products for use in
one ioad uniess specified on the iabei.
Do not mix chlorine bleach with ammonia
or acids such as vinegar. Follow package
directions when using laundry products.
Incorrect usage can produce poisonous gas,
resulting in serious injury or death.
Do not reach into the washer while parts are
moving. Before loading, unloading or adding
items, push in the cycle selector knob and
allow the drum to coast to a complete stop
before reaching inside. Failure to follow this
warning can cause serious injury, fire, electrical
shock, or death.
Do not aiiow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children. As children grow, teach them the
proper, safe use of aH appmiances. Failure to
comply with these warnings could result in serious
personal injuries.
Destroy the carton, pmastic bag and other
packing materiams after the washer is
unpacked. Children might use them for play.
Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers.
Failure to comply with these warnings could result
in serious personal injuries or death.
Keep laundry products out of children's reach.
To prevent personaminjury, observe all warnings
on product mabeis. Failure to comply with these
warnings could result in serious personal injuries.
Remove the door to the washing compartment
to avoid the danger of chimdren or small animams
getting trapped inside before your washer is
removed from service or discarded. Failure
to do so can result in serious personal injury
or death.
$AVl= THR=$1=
6
SPECIAL FEATURES
O DETERGENT DISPENSER DRAWER
This four-compartment drawer provides separate
dispensers for prewash and main wash detergent,
liquid bleach, and liquid fabric softener.
CONTROL PANEL WiTH LED DISPLAY
Simple electronic controls are user-friendly.
The LED display indicates cycle options and
cycle time during operation.
EASY=ACCESS LOCKING DOOR
Extra-large door locks during operation and
features a delay to prevent the door from being
opened until the washer interior has cooled and
the water level has lowered.
PA TS AND FEATU ES
ROLLER JETS
The RollerJet system enhances wash
performance while reducing fabric wear.
Integrated jets spray clothes to further improve
washing efficiency.
DIRECT=DRIVE MOTOR
Direct-drive motor eliminates the belt and pulleys
found on most washers to provide improved
performance and reliability while increasing
energy efficiency.
7
PATS N U S
KEY PARTS AND COMPONENTS
In addition to the spec)al features and
components out)ined in the Special Features
section, there are severa) other important
components that are referenced in this manual
_) ULTRAoCAPACUTY STAUNLESS STEEL DRUM
The ultraqarge sta)nHessstee) drum offers extreme
durabi)ity and is t))ted to improve efficiency and
aUow easier access for Bargeitems.
LEVELUNG FEET
Four )eve)ing feet (two in the front and two in
the back) adjust to improve washer stabi)ity on
uneven floors.
DRA)N ACCESS PANEL
Provides access to the drain line and drain
pump filter.
Hot and Cold
Water Inlets
Drain
Hose
Rear of Washer
{nc(udedAccessories
Hot an
Water Hoses
_- (for removin_
shipping bolts and
adjusting leveling feet)
Tie Strap
(for securing
drain hose)
Caps (4) _
(for covering
shipping bolt holes)
Elbow Bracket
(for securing
drain hose)
8
INSTA[/MION INST UcTIONS
cHOOSE THE PROPER LOcATiON
WARN|NG
• Washer is heavy! Two or more people
are required when moving and unpacking
the washer. Failure to do so can result in back
or other injury.
=Store and install the washer where it will not
be exposed to temperatures below freezing
or exposed to outdoor weather conditions.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
• Properly ground washer to conform with all
governing codes and ordinances. Failure to
follow this warning can cause serious injury, fire,
electrical shock, or death.
• To reduce the risk of electric shock, do not
install the washer in humid spaces. Failure to
follow this warning can cause serious injury,fire,
electrical shock, or death.
The base opening must not be obstructed by
carpeting when the washer is installed on a
carpeted floor.
= DO not remove ground prong. Do not use
an adapter or extension cord. Plug into a
grounded 3=prong outlet. Failure to follow this
warning can cause serious injury, fire, electrical
shock, or death.
Power Outlet
=The power outlet must be within 60 in. (1.5 m) of
either side of the washer.
The appliance and outlet must be positioned so
that the plug is easily accessible.
Do not overload the outlet with more than one
appliance.
The outlet must be grounded in accordance with
current wiring codes and regulations.
Time-delay fuse or circuit breaker is
recommended.
NOTE: it is the personal responsibility and
obligation of the product owner to have a
proper outlet installed by a qualified electrician.
CLEARANCES
222/4"_
(57.5 cm)
0
IL:1111_"_:-111111
I-"_ 293/4"_ -"_4"
(75,6 om) (10 om)
521/4''
(133 cm)
To ensure sufficient clearance for water lines and
airflow, allow minimum clearances of at least
1 in. (2.5 cm) at the sides and 4 in. (10 cm)
behind the unit. Be sure to allow for wall, door,
or floor moldings that may increase the required
clearances.
m
g
0
27"
(2.5 cm) (68.6 cm) (2.5 cm)
Allow at least 24 in. (61.2 cm) in front of the
washer to open the door.
9
iN LLAT! N INST UCTI NS
FLOORING
TOminimize noise and vibration, the washer
MUST be installed on a soBidByconstructed floor.
See the NOTE at right.
AHowabBesBope under the entire washer is
1o maximum.
Carpeting and soft tiBesurfaces are not
recommended.
Never install the washer on a platform or weakBy
supported structure. Use onByan approved
accessory pedestaB as described beBow.
iNSTALLATiONS WiTH OPTIONAL
PI::DI::STAL BASF: OR STAcKiNG KiT
iMPORTANT: Ifyou are installing your washer
using an optional pedestal base or stacking kit,
please refer to the instructions for your pedestal
or stacking kit before proceeding with the
installation.
NOTE: PBeasenote that the floor must be strong
and rigid enough to support the weight of the
washer when fully loaded, without flexing or
bouncing. Rfyour floor has too much flex in it,
you may need to reinforce it to make it more
rigid. A floor that is adequate for a topqoading
washer may not be rigid enough for a front-
loading washer, due to the difference in the spin
speed and direction. If the floor is not solid, your
washer may vibrate and you may hear and feel
the vibration throughout your house.
Required Dimensions for Installation
With Pedestam
(75.6 cm) (10 cm)
Required Dimensions for Installation
With Stacking Kit
771/2''
(190,5 cm)
1"-¢_1 _ 27" _ _-1"
(2.5 cm) (68.6 cm) (2.5 cm)
10
INSTAI_/ATIONINST UcTIONS
UNPACKING AND REMOVING SHiPPiNG BOLTS
When removing the washer from the carton
base, be sure to remove the foam tub support
in the middle of the carton base.
If you must lay the washer down to remove the
base packaging materials, always lay it carefully
on its side. Do NOT lay the washer on its front
or back.
iMPORTANT: To prevent internal damage
during transport, the washer is equipped with
4 shipping bolts and plastic retainers. These
bolts and retainers MUST be removed before
operating the washer.
• Failure to remove shipping bolts and retainers
may cause severe vibration and noise, which can
lead to permanent damage to the washer. The
cord is secured to the back of the washer with
a shipping bolt to help prevent operation with
shipping bolts in place.
Foam Tub Carton Base
Support
Shipping
Bolts
Starting with the bottom 2 shipping bolts,
use the included wrench to remove the
4 shipping bolts by turning them
counterclockwise.
Remove the retainers by turning them slightly
while pulling. Rotate and press the hole caps
into the shipping bolt holes.
NOTE: Save the bolts and retainers for
future use. To prevent damage to internal
components, the shipping bolts and
retainers must be installed when
transporting the washer.
11
iN LLAT! N INST UCTI NS
cONNEcTiNG THE WATER LINES
IMPORTANT: Use new hoses when installing
the washer. Do NOT reuse oBdhoses.
IMPORTANT: Use ONLY the inlet hoses
provided by LG with this Baundry product.
Aftermarket hoses are not guaranteed to fit or
function correctly. Other hoses may not tighten
correctly and couBd cause Beaks.Subsequent
damage to product or property will not be
covered under the terms of LG's warranty.
Water suppBy pressure must be between 14.5
PSRand 116 PSR(100-800 kPa). Rfthe water
suppBy pressure is more than 116 PSR,
a pressure reducing vaBvemust be installed.
Periodically check the hose for cracks, Beaks,
and wear, and replace the hose if necessary.
Make sure that the water Binesare not stretched,
pinched, crushed, or kinked.
The washer should never be installed or stored
in a location subject to freezing temperatures.
Damage to the water lines and internal
mechanisms of the washer can result. If the
washer was exposed to freezing temperatures
prior to installation, allow it to stand at room
temperature for several hours before use.
Water Hose
(to water inlet
Rubber Seal
Insert a rubber seal into the threaded
fittings on each hose.
Rubber Seal
Water Hose ,7
(to tap)
12
Water
Inlets
Do not cross=thread the hose fittings.
Attach the hot water line to the red hot water
inlet on the back of the washer. Attach the
cold water line to the blue cold water inlet on
the back of the washer. Tighten the fittings
securely.
Water Tap
Attach the hot water line to the hot water
tap. Attach the cold water line to the cold
water tap.
Tighten the fittings securely. Open the water
taps fully to check for leaks.
INSTAI_I_MIONINST UcTIONS
CONNEcTiNG THE DRAIN LiNE
• The drain hose should always be properly
secured. Failure to properly secure the drain
hose can result in flooding and property
damage.
Do not install the end of the drain hose higher
than 96 in. (244.8 cm) above the bottom of the
washer.
The drain must be installed in accordance with
any applicable local codes and regulations.
Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
Option 1: Standpipe
_._ Elbow
Bracket
Drain
Hose
Clip the end of the hose into the elbow bracket.
Insert the end of the drain hose into a standpipe.
Use tie strap to secure the drain hose in place.
NOTE: Total height of the hose end should not
exceed 96 in. (244.8 cm) from the bottom of the
washer.
Option 2: Laundry Tub
Elbow
Bracket Laundry
/ Tub
x 2]
Clip the end of the hose into the elbow bracket.
Hang the end of the drain hose over the side of
the laundry tub. Use tie strap to secure the drain
hose in place.
NOTE: Total height of the hose end should not
exceed 96 in. (244.8 cm) from the bottom of the
washer.
In Strap
Hose
Option 3: Floor Drain
Drain Hose
Floor Drain
J
Insert the end of the drain hose into the floor
drain. Secure the hose in place to prevent it
from moving.
15
iN LLAT! N INST UCTI NS
LEVELING THE wASHER
The drum of your new washer spins at very high
speeds, up to 1,200 RPM. To minimize vibration,
noise, and unwanted movement, the floor must
be a perfectly BeveB,soBid surface.
NOTE: Adjust the leveBing feet onByas far as
necessary to BeveBthe washer. Extending the
BeveBingfeet more than necessary can cause
the washer to vibrate.
AIBfour BeveBingfeet must rest soBidByon the
floor. Rock the washer gently from corner to
corner to make sure that the washer does
not rock.
Rfyou are installing the washer on the optionaB
pedestaB, you must use the BeveBingfeet on
the pedestam to BeveBthe washer. The washer's
BeveBingfeet should be fully retracted and locked
into position with the Iocknuts.
Leveling
Feet
Position the washer in the final location,
taking special care to not pinch, strain, or
crush the water and drain lines. Place a level
across the top of the washer.
Leveling
Feet
Raise Lower
Loosen the Iocknuts on all 4 leveling feet
until you can turn the feet with the included
wrench. Turn clockwise to raise the washer
or counterclockwise to lower it.
o._
Tighten all 4
Iocknuts securely
J
Once the washer is level from side to side
and front to back, tighten all Iocknuts
securely.
Make sure that all 4 leveling feet are in firm
contact with the floor.
NOTE: To make sure that the washer is
properly level, run the washer with a test
load: place approximately 6 pounds of
laundry in the machine. Then, press POWER,
press RINSE+SPIN, and then press the
START/PAUSE button. See the following
sections for additional information on cycle
selection and operation.
14
Vedfy that the washer does not rock or
vibrate excessively during the spin cycle.
If the washer vibrates or shakes, adjust
the leveling feet until the washer is stable
and retest.
SORTING WASH LOADS
0 TO USE
FaDri¢ Care LaDels
Most articles of clothing feature fabric care labels
that include instructions for proper care.
Fabric Care Labels
wash
cycle .orma, Permanent"_press/ GentlY/
Water • Q • • • •
temperature Hot Warm Cold/cool
Bleach _ _
symbols Anybleach Only non-chlodne bleach Donot bleach
wrinkle resistant delicate
H h Do not wash Do not wring
(50°C/120°F) (40°C/105°F) (30°C/85°F)
(whenneeded) (whenneeded)
Loading the washer
* Check all pockets to make sure that they
are empty. Items such as clips, matches,
pens, coins, and keys can damage both your
washer and your clothes.
* Close zippers, hooks, and drawstrings to
prevent these items from snagging or tangling
on other clothes.
. Pretreat heavily stained areas for best results.
. Combine large and small items in a load. Load
large items first.
. Large items should not be more than half of the
total washload.
. The washer can be fully loaded, but the drum
should not be tightly packed with items. The
door of the washer should close easily.
. To prevent an out-of-balance load, do not wash
single items. Add one or two similar items to
the load. Large, bulky items, such as a blanket,
comforter, or bedspread should be washed
individually.
. Do not wash or spin waterproof clothes.
. When unloading the washer, check under the
door seal for small items.
Grouping Similar Items
For best results, sort clothes into loads that can
be washed with the same wash cycle.
Different fabrics have different care requirements.
Always wash dark colors separately from light
colors and whites to prevent discoloration. If
possible, do not wash heavily soiled items with
lightly soiled ones. The chart below shows
recommended groupings.
NOTE: The front loading washer rotates the
wet laundry to wash it with less water. If you
do not see the water during washing, it is not
a problem because the laundry is sufficiently
wet.
15
USE
SELECTING DETERGENT
iMPORTANT: Your washing machine is
designed for use with only High-Efficiency
(HE) detergents. HE detergents are formulated
specifically for front-load washers and contain
suds-reducing agents. Always look for the HE
symbol when purchasing detergent.
HE detergents produce fewer suds, dissolve
more efficiently to improve washing and rinsing
performance, and help to keep the interior of your
washer clean.
Using a regular detergent may cause oversudsing
and unsatisfactory performance.
ABOUT THi: DiSpi::NS!:R
The automatic dispenser consists of four
compartments which hold:
• Liquid chlorine bleach.
• Liquid fabric softener.
• Liquid or powdered detergent for prewash.
• Liquid or powdered detergent and color-safe
bleach for main wash.
All laundry products can be added at once in
their respective dispenser compartments. They
will be dispensed at the appropriate time for the
most effective cleaning.
After adding the laundry products to the
dispenser, close the dispenser drawer.
To add detergent, bleach, and fabric softener to
the automatic dispenser:
_Open the drawer.
Load the into the
appropriate compartments.
_ Slowly close the drawer tod_spenser
avoid early dispensing of the laundry
products.
NOTE: It is normal for a small amount of water to
remain in the dispenser compartments at the end
of the cycle.
d_spenser
Baundry products
iMPORTANT: Do not place or store laundry
products, such as detergent, bleach, or liquid
fabric softener, on top of your washer or dryer.
Wipe up any spills immediately. These products
can damage the finish and controls.
Designed spedalIv to use onlv
HE (High-Efficiencv} detergent
Liquid Chlorine Liquid Fabric
Bleach Softener
Compartment Compartment
.... _ Detergent
J
/
Main Wash Detergent
Compartment
Insert
Liquid
Prewash
Detergent
Compartment
J
16
LOADING THE DISPENSER
0 TO USE
Prewash Detergent Compartment
Add liquid or powdered detergent to this
compartment when using the Prewash option.
Always use HE (High-Efficiency) detergent with
your washing machine.
• The amount of detergent added for the Prewash
option is 1/2 the amount recommended for the
main wash cycle. For example, if the main wash
cycle requires one cup of detergent, add 1/2
cup for the Prewash option.
NOTE: If liquid detergent is to be used for the
main wash when using the pre-wash option, the
liquid detergent cup accessory must be used
in main wash dispenser to prevent the main
wash liquid detergent from being dispensed
immediately.
Main wash Detergent Compartment
This compartment holds laundry detergent
for the main wash cycle, which is added to
the load at the beginning of the cycle. Always
use HE (High-Efficbncy) detergent with your
washing machine.
Never exceed the manufacturer's
recommendations when adding detergent.
Using too much detergent can result in
detergent buildup in clothing and the washer.
Either powdered or liquid detergent may be used.
When using liquid detergent, make sure the
liquid detergent cup and insert are in place.
Do not exceed the maximum fill line.
When using powdered detergent, remove
the insert and liquid detergent cup from the
compartment. Powdered detergent will not
dispense with the liquid detergent cup and
insert in place.
NOTE: Liquid or powdered color-safe bleach
may be added to the main wash compartment
with detergent of the same type.
Liquid Bleach Compartment
This compartment holds liquid chlorine bleach,
which will be dispensed automatically at the
proper time during the wash cycle.
Do not add powdered or liquid color-safe bleach
to this compartment.
Always follow the manufacturer's
recommendations when adding bleach. Do not
exceed the maximum fill line. Using too much
bleach can damage fabrics.
Never pour undiluted liquid chlorine bleach
directly onto the load or into the drum. Fabric
damage can occur.
Fabric Softener Compartment
This compartment holds liquid fabric softener,
which will be automatically dispensed during the
final rinse cycle.
Always follow the manufacturer's
recommendations when adding fabric softener.
Do not exceed the maximum fill line. Using
too much fabric softener may result in stained
clothes.
Dilute concentrated fabric softeners with warm
water. Do not exceed the maximum fill line.
Never pour fabric softener directly onto the load
or into the drum.
Designed speciallv to use onlv
HE (High-Efficiencv) detergent
17
CONTROL PANEL FEATURES
POWER ON/OFF BUTTON
Press to turn the washer ON. Press again to turn
the washer OFR
NOTE: Pressing the ON/OFF button during a
cycHewill canceHthat cycHeand any Hoadsettings
will be Host.
CYCLE SELECTOR KNOB
Turn this knob to seHectthe desired cycHe. Once
the desired cycHehas been seHected, the standard
presets will be shown in the dispHay.These
settings can be adjusted using the cycle setting
buttons anytime before starting the cycle.
START/PAUSE BUTTON
Press this button to START the selected cycle.
If the washer is running, use this button to PAUSE
the cycle without losing the current settings.
NOTE: If you do not press the START/'PAUSE
button within 4 minutes of selecting a cycle, the
washer automatically turns off.
STAUN CYCLE
Select this option for heavily stained clothes,
such as play clothes or work clothes. Stain Cycle
will add extra wash time to the selected cycle, as
well as an additional rinse cycle.
CYCLE SETTUNG BUTTONS
Use these buttons to seHectthe desired cycHe
options for the seHected cycHe.Press the button
for that setting untiHthe indicator Bight for the
desired vaHueis Hit.
DELAY WASH BUTTON
0
Press this button to delay the start of the wash
cycle. Each press of the button increases the
delay time by one hour, up to 19 hours.
LED DUSPLAY
@
The display shows the settings, estimated
time remaining, options, and status messages
for your washer. The display will remain on
through the cycle.
O
OPTUON BUTTONS
The option buttons aIHowyou to select
additional cycle options and will light when
selected. Certain buttons also aHIowyou to
activate special functions by pressing and
holding the button for 3 seconds.
For detailed information about the individual
options, please see the following pages.
18
0 TO USE
CYCLE GUIDE
The cycle guide below shows the options and recommended fabric types for each cycle.
f
Sanitary
Bright White TM
Cold CareTM
Bulky/Large
Perm Press
Cotton/
Normal
Heavy Duty
Towels
Small Load
Delicates
Hand Wash/
Wool
Speed
Wash
Heavily soiled
underwear, work
c othes, d apers, etc
White Fabrics
Small loads of cotton,
linen, towels,
Shirts, sheets, jeans,
mixed loads
Large items such as
blankets and comforters
Dress shirts/pants,
wrinkle free clothing,
poly/cotton blend
clothing, table cloths
Cotton, linen, towels,
shirts, sheets, jeans,
mixed loads
Heavy soiled Cotton
Fabrics
Towels and cotton
Cotton, linen, towels,
shirts, sheets, jeans,
mixed loads
Dress shirts/blouses
nylons, sheer or lacy
garments
Items labeled
"hand washable"
Lightly soiled clothing
and small loads
Extra Hot/Cold
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Hot/Cold
Cold/Cold
Cold/Cold
Warm/Cold
Warm/Warm
Warm/Cold
Warm/Warm
Cold/Cold
Hot/Cold
Cold/Cold
Warm/Cold
Warm/Warm
High
Extra High
No Spin
Low
Medium
High
Extra High
No Spin
Low
Medium
High
Extra High
No Spin
Low
Medium
Low
Medium
No Spin
Medium
High
No Spin
Low
High
Extra High
No Spin
Low
Medium
Extra High
No Spin
Low
Medium
High
Medium
High
Extra High
No Spin
Low
High
Extra High
No Spin
Low
Medium
Medium
No Spin
Low
Low
No Spin
Extra High
No Spin
Low
Medium
High
Normal
Heavy
Light
Normal
Heavy
Light
Normal
Light
Normal
Heavy
Light
Normal
Heavy
Light
Normal
Heavy
Light
Heavy
Light
Normal
Normal
Heavy
Light
Normal
Heavy
Light
Normal
Heavy
Light
Normal
Light
Light
Normal
Heavy
NOTE: To protect your garments, not every
option isavailable with everycycle.
wash/rinse temperature, spin speed, soil level, or
THE LED DISPLAY
The LED dispBay shows the settings, estimated time remaining, options, and status messages
for your washer. When the washer is turned on, the dispBay will illuminate.
DOOR LOCK uNDuCATOR
CYCLE COIViPLETUON UNDUCATOR
This portion of the dispBay shows which stage
of the wash cycBe is currently underway (LOAD
SENSRNG, WASH, RRNSEor SPRN).
ESTUMATED TUME REMAUNUNG
@
When the START/PAUSE button is pressed, the
washer automatically detects the wash Boad
(weight) and optimizes the washing time, based
on the selected cycBeand options. The display
will then indicate the estimated time remaining
for the selected wash cycle.
NOTE: The cycle time displayed may appear
much longer than that of a top=loading washer.
The displayed time is for the complete cycle,
rather than just the agitation portion of the cycle,
as is typically shown on a topqoading washer.
O
Indicates that the door is locked. The washer
door will lock while the washer is operating. The
door can be unlocked by pressing the START,,'
PAUSE button to stop the washer.
NOTE: If the temperature in the washer is too
high, the door cannot be unlocked until the
washer has cooled. If the water level is too
high, select the DRAIN & SPIN cycle to drain
excess water. Do not try to force open the door.
DELAY WASH UNDUCATOR
O
This indicator shows that the washer has
been set for DELAY WASH. The washer will
start automatically after the set delay time
has passed.
2O
OPERATING THE WASHER
Once you have loaded the washer and added
laundry products (detergent, bleach, and/or
fabric softener):
O Press the ON/OFF button to turn on the
washer. The lights around the cycle
selector knob will illuminate.
O Turn the cycle selector knob to the desired
cycle. The display will show the
preset Rinse/Wash Temperature,
Spin Speed, Soil Level, and
Option settings for that cycle.
Ifyou would like to change the settings for
that cycle, press the appropriate cycle set-
tings button(s) until the indicator light for the
desired setting is lit.
NOTE: To protect your garments, not every
wash/rinse temperature, spin speed, soil
level, or option is available with every cycle.
0 TO USE
O Press the START/PAUSE button
the cycle. The door will latch,
the display will change, and
the washer will calculate the
estimated time remaining. Once
the washer has calculated the estimated
total cycle time, the washer will start. To
pause the cycle at any time, press PAUSE.
NOTE: The cycle time displayed may
appear much longer than that of a top-
loading washer. The displayed time is for the
complete cycle, rather than just the agitation
portion of the cycle, as is typically shown on
a top-loading washer.
NOTE: ifthe temperature in the washer is
too high, the door cannot be unlocked until
the washer has cooled. If the water level is
too high, select the DRAIN & SPIN cycle to
drain excess water. Do not try to force the
door open.
Washing time can be reduced significantly
for small or lightly soiled loads by selecting
the Speed Wash cycle and setting the Soil
Level button to Light.
to
begin
Select any additional cycle options, such as
STAIN CYCLE or
_ DELAY WASH
_ option.
NOTE: To protect your garments, not every
wash/rinse temperature, spin speed, soil
level, or option is available with every cycle.
by pressing the
button for that
O
When the load is finished, the beeper (if set)
will sound and the door will unlock.
Remove damp clothes from the washer
immediately. Check under the door seal
for small items.
21
CYCLESETTING BUTTONS
Each cycle has preset settings that are selected
automatically. You may also customize the
settings using the cycle setting buttons.
Press the button for that setting until the indicator
light forthe desired value is lit.
The washer automatically adjusts the water level
for the type and size of wash load for best results
and maximum efficiency. It may seem there is no
water inside the drum in some cycles, but this is
normal.
NOTE: To protect your garments, not every wash/
dnse temperature, spin speed, soil level, or option
is available with every cycle. See the Cycle Guide
for details.
WASH/RINSE
Selects the wash and rinse
temperature combination for the
selected cycle. Press the WASH/RINSE
button until the indicator light for the
desired setting is lit.
Your washer features a heating element to
boost the hot water temperature for Extra
Hot settings. This provides improved wash
performance at normal water heater settings.
Select the water temperature suitable for the
type of load you are washing. Follow the fabric
care label for best results.
Warm rinses leave the loads drier than cold
rinses. Warm rinses can increase wrinkling.
In cold climates, a warm rinse makes the load
more comfortable to handle.
Cold rinses use less energy.
BEEPER
Adjusts the volume of the end=of=cycle
beeper, or turns it off.
SPIN SPEED
The washer drum spins at up to 1,200
RPM. This reduces drying time and
saves energy. Press the SPIN SPEED
button until the indicator light for
the desired setting is lit. Some fabrics, such as
delicates, require a slower spin speed.
The Drain & Spin cycle:
The Spin Speed button also activates the Drain
& Spin cycle to drain the tub and spin clothes;
for example, if you want to remove clothes before
the cycle has ended.
To activate the DRAIN & SPiN cycle:
Press the ON/OFF button to turn on
the washer.
O Press the SPIN SPEED button.
_ Select the desired spin speed.
NOTE: If NO SPIN is selected, the washer
will drain only.
Press the START/PAUSE button.
SOIL LEVEl.
Adjusts the selected cycle to allow
more time for heavily soiled clothes or
less time for lightly soiled clothes.
Press the SOIL LEVEL button until the
indicator light for the desired setting is
lit.
CYCLE OPTION BUTTONS
0 TO USE
Your washing machine features several additional
cycle options to customize cycles to meet your
individual needs. Certain option buttons also
feature a special function (see the following page
for details) that can be activated by pressing and
holding that option button for 3 seconds.
TOAdd Cycle Options to a Cycle:
O Turn on the washer and turn the cycle
selector knob to select the desired cycle.
O Use the buttons to the
settings for that cycle.
Press the cycle option button(s) for the
O
option you would like to add. The cycle
option buttons, except STAIN CYCLE and
DELAY, will light when selected.
O Press the START/PAUSE button to start the
cycle. The washer will start automatically.
NOTE: To protect your garments, not every wash/
rinse temperature, spin speed, soil level, or option
is available with every cycle. See the Cycle Guide
for details.
cycle setting adjust
PREWASH
Select this option to add a 16-minute
prewash and spin cycle to the chosen
cycle. This is especially useful for
heavily soiled items.
STAIN CYCLE
Select this option for heavily stained
clothes, such as play clothes or work
clothes. Stain Cycle will add extra
wash time to the selected cycle, as
well as an additional rinse cycle.
DELA Y WASH
other settings, press this button to
Once you have selected the cycle and
delay the start of the wash cycle. Each
-- press of the button increases the delay
time by one hour, up to 19 hours.
25
CYCLE OPTION BUTTONS {cont.)
RINSE+SPIN
SeBect this option to rinse and spin a
Boadseparately from a regular cycBe.
This can be helpfuB in preventing fresh
stains from setting in fabrics.
To activate the Rinse+Spin cycle:
O Press the ON/OFF button to turn
the washer.
O Press the RRNSE+SPRNbutton.
Press the START/PAUSE button.
EXTRA RINSE
This option will add an extra rinse
cycle to the selected cycle. Use this
option to help ensure the removal
of detergent or bleach residue from
fabrics.
on
WASH/RINSE OPTIMIZER TM
This function can adjust washing &
rinsing time efficiently with checking
the BeveBof detergent and degree of
hardness.
Excessive detergent amount: rinsing cycle
_ncrease.
Rnsufficient detergent washing
_ncrease.
A small amount of remaining detergent
detected, additionaB rinsing will be added.
WATER PLUS
Select this option to add extra water to
the wash and rinse cycles for superior
results, especially with large or bulky
items.
amount: time
24
SPEciAL FUNcTiONS
0 TO USE
The option buttons also activate special
functions, including CHILD LOCK, and TUB
CLEAN. Press and hold the option button
marked with the special function for 3 seconds to
activate.
CHILD LOCK
of the washer or to keep cycle settings
Use this option to prevent unwanted use
from being changed while the washer is
operating. Press and hold the PREWASH
button for 3 seconds to activate or deactivate CHILD
LOCK.
The lock icon will be shown in the display, and all
controls are disabled. The washer can be locked
during a cycle. Once CHILD LOCK is selected, the
display will alternate between CL and the remaining.
TUB CLEAN
A buildup of detergent residue can
occur in the wash tub over time and
can lead to a mildewy or musty smell.
The TUB CLEAN cycle is specially
designed to remove this buildup. Fill the bleach
dispenser to the MAX. line. Press and hold the
EXTRA RINSE button for 3 seconds to activate
this cycle. After the cycle has ended, open
the door and allow the drum interior to dry
completely. Refer to Care and Cleaning of the
Interior for further information.
NOTE: Do NOT use this cycle with clothes,
and do NOT add detergent or fabric softener.
NOTE: If you use the TUB CLEAN cycle on a
monthly basis, the wash drum will be kept clean.
COLD CARE TM
Use this cycle to wash without hot water and
heating. For high wash efficiency, recommended
less than 8 Ibs. and low speed spin for ultimate
fabric care.
BRIGHT WHITE TM
Use this cycle to wash white fabrics with bleach.
NOTE : Before use this cycle with bleach, check
bleach symbols on your cloths.
HAND WASH/WOOL
• Only woolen items that are designated as
"Machine-Washable" should be washed in this
washing machine
• Wash only small loads for optimum fabric care
(less than 8 Ibs.)
• Only neutral (wool safe) detergents should
be used (Only a small quantity of detergent
is needed due to the small load size and low
volume of water in the cycle.)
• The HANDWASH/WOOL cycle uses a gentle
tumble action and low speed spin for ultimate
fabric care
The wool wash cycle of this machine has been
(_ approved by Woolmark for the washing of machine
WOOLMARK on the garment label and those issued by the
_S_ Certified by NSF
washable Woolmark products provided that the
products are washed according to the instructions
manufacturer of this washing machine, M0807.
Certificado pot NSF
NSF International (formerly the National Sanitation Foundation),
certifies that SANITARY cycle reduces 99.9% of bacteria on
laundry, and none of bacteria will carry over onto the next laundry
load.
25
C N C
REGULAR CLEANING
WARNING:
• Unplug the washer before cleaning to avoid the risk of electric shock, FaiBureto follow this warning
can cause serious injury, fire, eBectricaBshock, or death.
Never use harsh chemicams, abrasive cleaners, or somvents to dean the washer,
They will damage the finish.
Cleaning the Exterior
Proper care of your washer can extend its Bife.
The outside of the machine can be cBeaned with
warm water and a miBd, nonabrasive househoBd
detergent.
RmmediateBywipe off any spills with a soft, damp
cBoth.
mMPORTANT: Do not use methylated spirits,
solvents, or similar products.
Never use steel wool or abrasive cleansers; they
can damage the surface.
Care and Cleaning of the Interior
Use a towel or soft cloth to wipe around the
washer door opening, door seal, and door glass.
These areas should be kept clean to ensure a
watertight seal. Be sure to wipe under the inside
rubber seal to remove any moisture or soil.
Always remove items from the washer as soon
as the cycle is completed. Leaving damp items
in the washer can cause wrinkling, color transfer,
and odor.
Run the TUB CLEAN cycle regularly to remove
detergent buildup and other residue.
This washer has a special cycle, TUB CLEAN, to
remove inside buildup of detergent residue which
can occur in the wash tub or drum and lead to
mildew or musty smell.
Read these instructions carefully before
beginning the TUB CLEAN cycle.
0 Open the door and remove any clothing in
the wash drum.
Open the dispenser drawer.
Add liquid chlorine bleach or tub cleaner.
Some powder or tablet tub cleaners which
are manufactured for this purpose can be
used.
(NOTE : Do not add any laundry detergent
or fabric softener to the drawer when using
TUB CLEAN.)
- ff using miquid chmorine bleach
Add liquid chlorine bleach to the bleach
compartment of the drawer.
(NOTE : Do not exceed the maximum
fill line and do not pour undiluted liquid
bleach directly into the wash drum.)
- ff using powder cleaner
Remove the liquid detergent cup and
add powder cleaner to the main wash
compartment of the drawer.
- ff using tabmet cleaner
Add tablet cleaner to the wash drum
directly.
(NOTE : Do not add tablet cleaner to the
drawer.)
Close the drawer and washer door.
O
26
Select TUB CLEAN and press START.
NOTE : It is recommended that TUB CLEAN
should be repeated monthly.
If mildew or musty smell already exists, run TUB
CLEAN for 3 consecutive weeks.
After TUB CLEAN is complete or when the washer
is not used, leave the washer door open for better
ventilation and drying inside of the washer.
REGULAR cLEANiNG (cOnt.)
CA E AND CLEANING
Cleaning the Steam and Water
Circulation Nozzles
Use a cotton swab to remove lime or detergent
buildup from the inside of the steam and water
circulation nozzles. NEVER use a sharp or
pointed object; you could damage the nozzles.
Removing the Stain in Door Seal
NOTE: Wear rubber gloves and eye protection
while performing the following procedure:
O Dilute 3/4 cup (177 ml)liquid chlorine bleach
with 1 gallon (3.8 L) of warm/hot water.
e Use this solution to wipe down all surfaces
of the gasket to remove the deposits that are
causing any odor. (Be sure to fold back the
lip of the gasket to get under the edge where
residue can build up.)
Wipe the gasket with a dry cloth.
Leave the door open to allow the gasket to
dry completely.
Do not use undiluted bleach as this will damage
the gasket.Follow the manufacturer's instructions
for proper use of bleach.
If the gasket cannot be cleaned properly, it should
be replaced.
Storing the Washer
If the washer will not be used for an extended
period of time and is in an area that could be
exposed to freezing temperatures:
Turn off water
Disconnect hoses from water supply and
drain water from hoses.
Plug the power cord into a properly grounded
electrical outlet.
Add 1 gallon of nontoxic recreational vehicle
(RV)antifreeze to the empty wash drum.
Close door.
Select the spin cycle and let washer spin
O
for 1 minute to drain out all the water.
NOTE: Not all of the RV antifreeze will be
expelled.
Unplug the power cord, dry the drum interior
with a soft cloth, and close the door.
Remove the inserts from the dispenser. Drain
any water in compartments and dry the
compartments.
Store the washer in an upright position.
To remove the antifreeze from the washer
after storage, run washer through a complete
cycle using detergent. Do not add laundry!
Removing Lime Buildup
If you live in an area with hard water, lime scale
can form on internal components of the washer.
Use of a water softener is recommended in areas
with hard water. If a descaler is used, make sure
that it is suitable for use in a washer, and run the
TUB CLEAN cycle before washing clothing.
Lime scale and other spots may be removed
from the stainless steel drum using a stainless
steel cleaner. Do NOT use steel wool or abrasive
cleansers; they can damage the surface.
supply tap.
NOtiCe Of tub clean activation
To clean up the tub, please select the tub clean
course. Please empty the tub and insert bleach
into the detergent dispenser and push the tub
clean button.
Door open recommended
it is recommended that you should leave the door
open after getting finished with laundry to keep
the tub clean.
27
C N C
CLEANING THE WASHEff
Cleaning the Dispenser
The dispenser should be cBeaned periodically
to remove buiBdup from detergent and other
laundry products.
Pull out the dispenser drawer untiBit stops.
Press the button in the center of the drawer
and pull to remove the drawer.
NOTE; Rfyou cBeanthe detergent dispenser once
a week, it will aBways dispense properly.
Remove the inserts from the drawer, and
cBeanthem with warm water and a soft
cBoth or brush to remove any residue or
buiBdup.
Wipe out the inside of the drawer opening
with a damp cBoth. ReassembBe the drawer
and reinstall in the drawer opening.
NOTE; Do not use anything other than
water to cBeanthe drawer, inserts, and
drawer opening. If any sort of household
cleaner drains into the interior of the
washer, run a RINSE+SPIN cycle before
washing clothes.
28
MAiNTENANcE
CA E AND CLEANING
Cleaning the Water Inlet Filters
if the washer detects that water is not entering
the dispenser, an error message will show on the
display. If you live in an area with hard water, this
may be caused by clogged inlet filters.
iMPORTANT: Use extreme care when removing
and cleaning the filters, if the filters cannot be
cleaned or are damaged, do NOT operate the
washer without the inlet filters. Contact LG
Customer Service or a qualified LG servicer.
IMPORTANTE: Use ONLY the inlet hoses
provided by LG with this laundry product.
Aftermarket hoses are not guaranteed to fit or
function correctly. Other hoses may not tighten
correctly and could cause leaks. Subsequent
damage to product or property will not be
covered under the terms of LG's warranty.
@
Inlet Filter
Turn off both water taps completely. Unscrew
the hot and cold water lines from the back of
the washer.
Carefully remove the filters from the water
inlets, and soak them in white vinegar
or a lime scale remover, following the
manufacturer's instructions. Rinse thoroughly
before reinstalling.
Press the filters back into place and reattach
the water lines. Do NOT operate the washer
without the inlet filters.
29
C N C
MAINTENANCE _cont.)
Cleaning the Drain Pump Filter
Lint and other objects may accumulate and cBog
the drain pump filter. Rfthe washer faiBsto drain
properly, unpBug the washer and allow the water
to cool, if necessary, before proceeding.
t
Open the drain pump fiBteraccess panel
Plug
Drain Hose
J
UncBipthe drain hose and puBIit out. PBace
the end of the drain hose in a pan, bucket, or
floor drain to catch water.
5O
Remove the pBugfrom the drain hose, and
allow the water to drain completely.
Twist the pump filter counterclockwise to
remove. Remove any Bintand foreign objects
from the pump filter.
Reverse the above steps to reinstall the drain
pump filter and drain hose. Be sure to close
the cover panel when finished.
Loading...