LG WM2240CS Owner's manual
OWNER’S MANUAL
WASHING MACHINE
WM2240CS
P/No.: MFL62526883
www.lg.com
Please read this manual carefully before operating
your set and retain it for future reference.
ENGLISH ESPAÑOL
roduct Feature
P
ontents
C
2
Warnings...............................................................................................3
Specification..........................................................................................4
Installation.............................................................................................5
Care before washing...........................................................................10
Using the dispenser ............................................................................11
Function ..............................................................................................13
How to use washer .............................................................................14
Maintenance .......................................................................................20
Troubleshooting guide ........................................................................23
■ Ultra Capacity
The Larger drum enables not just higher head drop and stronger
centrifugal force, but also less tangling and wrinkling of the laundry.
Heavier loads, such as king size comforters, blankets, and curtains, can
be washed.
■ Direct Drive System
The advanced Brushless DC motor directly drives the drum without belt
and pulley.
■ Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
■ Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
■ Child Lock
The Child lock prevents children from pressing any button to change the
settings during operation.
■ Magnetic Door Plunger
Safely and conveniently secure the door slightly ajar with a magnetic door
plunger. This will promote air circulation and allow the interior of the
machine to dry. To use this feature, after the load has been removed, do
not close the door completely. When the magnetic door plunger comes
into contact with the metal washer cabinet, it will secure the door slightly
open allowing the interior of the washer to dry.
추가선택 예약
추가선택 예약
arnings
W
3
ENGLISH
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
!
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
• Read all instructions before using the washer.
• Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other
flammable or explosive substances, as they give
off vapors that could ignite or explode.
• Do not add gasoline, dry cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors
that could ignite or explode.
• Under certain conditions, hydrogen gas may be
produced in a hot water system that has not
been used for 2 weeks or more. HYDROGEN
GAS IS EXPLOSIVE. If the hot water system
has not been used for such a period, before
using the washing machine, turn on all hot water
faucets and let the water flow from each for
several minutes. This will release any
accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame
during this time.
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children.
• Before the washer is removed from service or
discarded, remove the door to prevent children
from hiding inside.
• Do not install or store the washer where it will be
exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• See Installation Instructions for grounding
requirements.
• ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
• Do not place items exposed to cooking oil in
your washer. Items contaminated with cooking
oils may contribute to a chemical reaction that
could cause a load to catch fire.
• Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or extension cord.
• Do not remove ground prong.
• If you don’t have the proper outlet, consult an electrician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
SAVE THESE INSTRUCTIONS
WARNING :
Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance
is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet,
have a proper outlet installed by a qualified electrician.
!
!
pecification
S
4
Name : Front loading washing machine
Power supply : 120 V~, 60 Hz
Size : 686 mm(W)×756 mm(D)×983 mm(H) /
1297 mm (D, door open)
Weigh : 87 kg (191.8 libras)
Wash capacity : 15 kg (33 libras)
Max. Watt : 600 W
Spin speed : 1200 rpm max.
Permissible water pressure : 0.3-10kgf/cm
2
(30-1000kPa)
❋ The appearance and specifications may be varied without notice to raise the units quality.
Accessories
Inlet hose 2EA Spanner Caps (4EA) Tie Strap Elbow Bracket Non-skid
pads
nstallation
I
5
ENGLISH
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
• If they are not removed, it may cause severe
vibration, noise and malfunction.
3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future use.
• Whenever the appliance is transported, the
transit bolts must be refitted.
The appliance is fitted with transit bolts to prevent internal damage during transport.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
Removing transit bolts
cap
Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
Properly ground washer to conform with all governing codes and ordinances.
To reduce the risk of electric shock, do not install the washer in humid spaces.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at
all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance
guarantee.
Transit bolts
6
nstallation
I
■Installation clearances
The location must be large enough to fully open
the washer door.
■ Washer dimensions
• Most installations require a minimum
10 cm clearance behind the washer.
■ Minimum installation spacing for recessed
area installation.
The following dimensions shown are for the
minimum spacing allowed.
Additional spacing should be considered for
installation and servicing.
• Additional clearances might be required
for wall, door and floor moldings.
• Additional spacing of 2.5 cm on all
sides of the washer is recommended to
reduce noise transfer.
Companion appliance spacing should also be
considered.
[Front view]
[Side view]
129.7 cm
68.6 cm
75.6 cm
98.3 cm
■ Level floor
• Allowable slope under entire washer is 1°.
• To minimize noise and vibration, the washer
MUST be installed on a solidly constructed floor.
• Carpeting and soft tile surfaces are not
recommended.
• Never install the washer on a platform or weakly
supported structure.
NOTE: A firm, solid floor is even more critical to a front-
loading washer than to a top-loader.
If your floor is wood and/or frame construction, you
may need to reinforce it. Front-loaders use
substantially faster spin speeds than top-loaders,
causing greater vibration. If the floor is not solid,
your washer will vibrate. You will hear and feel the
vibration throughout your house.
■ Power outlet
• Must be within 60 in. (1.5 m) of either side of the
washer. Do not overload the outlet with more
than one appliance.
• Time-delay fuse or circuit breaker is recommended.
NOTE: It is the personal responsibility and obligation of the
customer to have a proper outlet installed by a
qualified electrician.
7
ENGLISH
nstallation
I
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
CAUTION
▶
Water supply pressure must be between 30kPa and 1000kPa
(0.3~10kgf/cm
2
)
▶
Don’t strip or crossthread when connecting Inlet hose to the valve.
▶
If the water supply pressure is more than 1000kPa, a decompression device
should be installed.
• Two rubber seals are supplied with the water inlet hoses these are in
order to prevent water leaks.
• Check water tightness of washing machine connections by turning the
tap completely on.
• Periodically check the condition of the hose and replace the hose if
necessary.
• Make sure that there is no kink on the hose and that it is not crushed.
▶
When your washer has two valves,
• The Inlet hose which has red connector is for the hot water tap.
• If the washer has two valves, the energy is saved by using hot valve.
Washing Machine is to be connected to the water mains using new hose-sets and that old
hose-sets should not be used.
Connecting water supply hose
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or
similarly qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses
may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below
freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing
machine at room temperature for a few hours before putting it into operation.
Electrical connection
Hose connector
Rubber seal
Hot water tap
Hot(Option)Cold
Cold water
tap
8
nstallation
I
Installation of drain hose
about
about
about
• The drain hose should not be placed
higher than 100 cm above the floor.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
• When the drain hose is too long, do
not force back into the washer. This
will cause abnormal noise.
• When installing the drain hose sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
• Place the end of the drain hose in the
hole of the floor drain system.
This equipment is not designed for maritime use or for use mobile installations such as
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the
door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation !
Keep all packaging well away from children.
about
about
about
Laundry tub
max. 100cm
min. 60cm
Hose
Retainer
Tie
strap
max. 100cm
min. 60cm
9
ENGLISH
nstallation
I
Level adjustment
Installation of non-skid pads (optional)
1. Adjusting the washing machine level properly prevents
excessive noise and vibration.
Install the appliance on a solid and level floor surface,
preferably in a corner of the room.
NOTE: Extend the feet no more than necessary to level the
washer. The more the feet are extended, the more the
washer will vibrate.
2. If the floor is uneven, adjust the adjustable feet as
required. (Do not insert pieces of wood etc. under the
feet)
Make sure that all four feet are stable and resting on the
floor and then check that the appliance is perfectly level.
(Use a spirit level)
❊ After the washer is level, tighten the lock nuts up towards
of the base of the washer. All lock nuts must be tightened.
NOTE: If there are vibration and noise during the spin cycle,
re-check the leveling of the washer, adjust the feet as
required, and tighten the lock nuts securely to prevent
changes in adjustment.
Run the washer with a test load to make certain your
washer is properly leveled. Put approximately 6 pounds
of laundry in the machine. Then, press POWER,
RINSE+SPIN, and START/PAUSE, in that order.
When the machine spins at high speed, verify that it is
stable. If not, adjust
❊ Diagonal Check
When pushing down the edges of the washing machine top
plate diagonally, the machine should not move up and down at
all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate
diagonally, adjust the feet again.
Some floor surfaces are too slippery to
prevent the washer from moving on the floor
during heavily unbalanced loads. While it is
normal for an occasional load to be out of
balance, excess noise and vibration can
result from the washer moving out of position.
If these conditions are encountered, follow
the instructions below for installation of the
non-skid pads. These pads will help prevent
the washer from moving during heavy out of
balance conditions thereby reducing noise
and vibration.
• Non-skid pads
✼ Place the pads under both front feet.
Adjustable feet Adjustable feet
Lock nut
This side up
Stick adhesive side to floor
Remove backing
10
are before washing
C
1. Fabric Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your
garment and how it should be washed.
2. Sorting
To get the best results, sort clothes into loads that can be washed with the same wash
cycle.
Different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint
transfer can occur causing discoloration of white clothing. If possible, do not wash
heavily soiled items with lightly soiled ones.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lights, Darks) Separate white fabrics from colored fabrics.
Lint (Lint Producers, Collectors) Wash lint producers and lint collectors separately.
3. Check before loading
Combine large and small items in a load. Load large items first.
Large items should not be more than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar
items.
• Check all the pockets to make sure that they
are empty. Things such as clip, matches,
pens, coins, and keys can damage both your
washer and your clothes.
• Close zippers, hooks, and strings to make
sure that these items do not snag on other
clothes.
• Pretreat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help lift dirt.
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
NOTE: Do not wash or spin water-proof clothes.
11
ENGLISH
sing the dispenser
U
The automatic dispenser consists of four compartments which hold 1) liquid chlorine bleach,
2) liquid fabric softener, 3) liquid or powdered detergent for prewash and 4) liquid or
powdered detergent
and color safe bleach for main wash.
All laundry products can be added at once in their respective dispenser compartments.
They will be dispensed at the appropriate time for most effective cleaning. After loading the
laundry
additives into the dispenser, close the dispenser drawer.
Add detergent, bleach and fabric softener to the automatic dispenser following
these steps:
1. Open the dispenser drawer.
2. Load the laundry products into the appropriate compartments.
3. Close the dispenser drawer.
■ About detergent
Low sudsing detergent is recommended for this washer. Use the manufacturer's
recommended amount.
If low sudsing detergent is not available, a reduced amount of regular detergent may be
used.
Because reducing the amount of detergent may reduce cleaning, it is important to
pretreat stains,
sort carefully by color and soil level, and avoid overloading.
Detergent usage may need to be adjusted for water temperature, water hardness, size
and soil level of the load.
For best results, avoid using too much detergent.
• Add detergent to this compartment
when using the Prewash option.
Liquid or powdered detergent may
be used in this compartment. The
detergent will automatically be
dispensed during Prewash if the
Prewash option is selected.
• Add 1/2 the recommended amount
of detergent to the Prewash
compartment and the
recommended amount of detergent
to the main wash compartment.
NOTE : Liquid detergent will drain
into the washer drum as it is
added.
Liquid Chlorine
Bleach
Compartment
Liquid Fabric
Softener
Compartment
Prewash
Compartment
Main Wash
Compartment
1. Prewash Detergent
Compartment
12
sing the dispenser
U
Liquid Detergent Box
Insert
• Add measured detergent to this
compartment for Main wash. Detergent
is flushed from the dispenser at the
beginning of the cycle. Either powdered
or liquid detergent can be used.
• Liquid or powdered color-safe bleach
may be added to the main wash
compartment along with the same type
of liquid or powdered detergent.
• When using liquid detergent, make sure
the liquid detergent box and insert are
in place. Do not exceed the maximum
fill line.
• For powered detergent, remove both
the liquid detergent box and insert.
• Powdered detergent will not dispense
with the liquid detergent box and insert
in place.
2. Main Wash Detergent
Compartment
• Add measured liquid chlorine bleach to
this compartment. The bleach will be
automatically dispensed at the proper
time during the wash cycle.
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing of
the bleach which could result in
damaged clothes.
• Do not pour undiluted liquid chlorine
bleach directly onto the load or into the
drum. Fabric damage can occur.
• Do not use powdered bleach in this
compartment.
3. Liquid Bleach Compartment
• Add recommended amount of fabric
softener to this compartment.
• Dilute concentrated softeners with
warm water to the fill line.
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing
of the fabric softener which could result
in stained clothes.
• Do not pour fabric softener directly on
the wash load.
• The fabric softener will be automatically
dispensed during the last rinse cycle.
4. Fabric Softener Compartment
NOTE: Do not place, store, or spill laundry
products (soap, detergent, bleach,
softener, etc.) on the top of your
washer or dryer. These products
can damage the finish or controls if
left there too long.
13
ENGLISH
unction
F
■ Select cycles designed for different types of fabric and soil levels.
Cycle Fabric Type Spin Speed
Soil
Level
Pre-
Wash
Quick
Cycle
Water
plus
Stain
Cycle
Extra
Rinse
Rinse+
Spin
Maximum
Load
Wash Temp.
NOTE: To protect your garments, not every Wash/Rinse temperature, spin speed, soil level or option is available with
every cycle.
Less than
8.0 kg
HAND WASH/
WOOL
Warm
Hot
Ecowarm
Cold
Tap Cold
Normal
Heavy
Light
Less than
8.0 kg
Less than
4.0 kg
Less than
15.0 kg
Less than
3.5 kg
Less than
4.0 kg
BULKY/
LARGE
Large items such
as blankets and
comforters
Low
Medium
No Spin
Cold
Warm
Ecowarm
Tap Cold
Normal
Heavy
Light
DELICATES
Dress
shirts/blouses,
nylons, sheer or
lacy garments
Medium
Low
No Spin
Warm
Ecowarm
Cold
Tap Cold
Normal
Light
DRAIN+
SPIN
Items labeled
“hand-washable”
Low
No spin
Warm
Hot
Ecowarm
Cold
Tap Cold
Normal
Heavy
Light
COTTON/
NORMAL
Cotton, linen,
towels, shirts,
sheets, jeans,
mixed loads
High
Extra High
Medium
Low
No Spin
Hot
Warm
Ecowarm
Cold
Tap Cold
Light
Heavy
Normal
SPEED
WASH
Lightly soiled
clothing and small
loads
Extra High
High
Medium
Low
No Spin
Warm
Hot
Ecowarm
Cold
Tap Cold
Normal
Heavy
Light
PERM.
PRESS
Dress shirts/pants,
wrinkle-free
clothing,
poly/cotton blend
clothing,
tablecloths
Medium
High
Low
No Spin
-
-
-
-
Drain, Spin
Only
High
Extra High
Medium
Low
No Spin
RECOMMENDED LOADS
14
ow to use washer
H
1. POWER ON/OFF BUTTON
2. CYCLE SELECTOR KNOB
3. START/PAUSE BUTTON
4. CYCLE SETTINGS BUTTONS
5. TIME AND STATUS
Turn this knob to select the desired cycle.
Once the desired cycle has been selected, the
standard presets will be shown in the display.
These settings can be adjusted using the cycle
settings buttons anytime before starting the
cycle.
Press to turn the washer ON. Press again to
turn the washer OFF.
NOTE: Pressing the ON/OFF button during a
cycle will cancel that cycle and any load settings
will be lost.
Press this button to START the selected cycle.
If the washer is running, use this button to
PAUSE the cycle without losing the current
settings.
NOTE: If you do not press the START/PAUSE
button within 4 minutes of selecting a cycle,
the washer automatically turns off.
The display shows the selected settings and
options, as well as the estimated time remaining
in the cycle.
6. OPTION BUTTON
The option buttons allow you to select additional
cycle options and will light when selected.
Certain buttons also allow you to activate
special functions by pressing and holding the
button for 3 seconds.
For detailed information about the individual
options, please see the following pages.
Use these buttons to adjust the desired cycle
options for the selected cycle.
4
1
2
3
5
6
6
15
ENGLISH
ow to use washer
H
THE TIME AND STATUS DISPLAY
1. ESTIMATED TIME REMAINING
When the START/PAUSE button is pressed, the
washer automatically detects the wash load
(weight) and optimizes the washing time, based
on the selected cycle and options. The display
will then indicate the estimated time remaining for
the selected wash cycle.
NOTE: The cycle time displayed may appear
much longer than that of a top-loading washer.
The displayed time is for the complete cycle,
rather than just the agitation portion of the cycle,
as is typically shown on a top-loading washer.
2. CYCLE COMPLETION INDICATOR
This portion of the display shows which stage
of the wash cycle is currently underway (LOAD
SENSING, WASH, RINSE, or SPIN).
3. DOOR LOCK INDICATOR
Indicates that the door is locked. The washer
door will lock while the washer is operating.
The door can be unlocked by pressing the
START/PAUSE button to stop the washer.
NOTE: If the temperature in the washer is too
high, the door cannot be unlocked until the
washer has cooled. If the water level is too
high, select the DRAIN & SPIN cycle to drain
excess water. Do not try to force open the door.
The time and status display shows the cycle progress and estimated time remaining, cycle options,
and other status messages for your washer.
3
1
2
16
ow to use washer
H
OPERATING THE WASHER
Once you have loaded the washer and added
laundry products (detergent, bleach, and/or fabric
softener):
❶ Press the ON/OFF button to turn on the
washer. The lights around the cycle
selector knob will illuminate.
❺ Press the START/PAUSE button to begin the
cycle. The door will latch, the display
will change, and the washer will
calculate the estimated time
remaining. Once the washer has
calculated the estimated total cycle time, the
washer will start. To pause the cycle at any
time, press START/PAUSE.
NOTE: The cycle time displayed may appear
much longer than that of a toploading washer.
The displayed time is for the complete cycle,
rather than just the agitation portion of the
cycle, as is typically shown on a top-loading
washer.
NOTE: If the temperature in the washer is too
high, the door cannot be unlocked until the
washer has cooled. If the water level is too
high, select the DRAIN & SPIN to drain
excess water. Do not try to force the door
open.
Washing time can be reduced significantly for
small or lightly soiled loads by selecting the
Speed Wash cycle and setting the Soil Level
button to Light.
❻ When the load is finished, the signal (if set)
will sound and the door will unlock.
Remove damp clothes from the washer
immediately. Check under the door seal for
small items.
❷ Turn the cycle selector knob to the desired
cycle. The display will show the
preset Wash Temp., Spin Speed,
Soil Level, and Option settings for
that cycle.
❹ Select any additional cycle options, such as
PRE-WASH, RINSE+SPIN,
QUICK CYCLE, STAIN
CYCLE, or TUB CLEAN by
pressing the OPTION button
until the desired option is lit.
NOTE: To protect your
garments, not every wash/rinse
temperature, spin speed, soil
level, or option is available with
every cycle.
❸ If you would like to change the settings for
that cycle, press the appropriate cycle setting
button(s) until the indicator light for the
desired setting is lit.
NOTE: To protect your garments, not every
wash temp., spin speed, soil level, or option is
available with every cycle.
17
ENGLISH
ow to use washer
H
CYCLE SETTING BUTTONS
Each cycle has preset settings that are selected
automatically. You may also customize the
settings using the cycle setting buttons. Press
the button for that setting until the indicator light
for the desired value is lit.
The washer automatically adjusts the water level
for the type and size of wash load for best
results and maximum efficiency. It may seem
there is no water inside the drum in some
cycles, but this is normal.
NOTE: To protect your garments, not every
wash temp., spin speed, soil level, or option is
available with every cycle. See the Cycle Guide
for details.
Selects the wash temperature
for the selected cycle.
Press the WASH TEMP. button
until the indicator light for the
desired setting is lit.
• Select the water temperature suitable for the
type of load you are washing. Follow the fabric
care label for best results.
WASH TEMP.
Adjusts the selected cycle to
allow more time for heavily
soiled clothes or less time for
lightly soiled clothes.
Press the SOIL LEVEL button
until the indicator light for the
desired setting is lit.
SOIL LEVEL
The washer drum spins at up to
1,200 RPM.
This extracts more water from
clothes, reducing drying time
and saving energy.
Press the SPIN SPEED button
until the indicator light for the desired setting is
lit. Some fabrics, such as delicates, require a
slower spin speed.
SPIN SPEED
Adjusts the end-of-cycle signal
volume or turns it off.
SIGNAL
Loading...