LG WFT11D80HP Owner’s Manual [ar]

P/No.: MFL42065445

Washing Machine

OWNER'S MANUAL

MODEL : WF-T13D80EP

WF-T15D81EP

Please read this manual carefully before operating your set.
Retain it for future reference.
Record model name and serial number of the set.
Quote this information to your dealer when you require service.

P

roduct Features

Note

Washer doesn't operate while the lid is open. If the lid is open during the wash,
rinse or spin cycles, the operation stops for safety.

Please close the door slowly because you will get hurt if you close it strongly.

A built-in load sensor automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal WATER LEVEL and
washing time.

Advanced technology is built into the Electronic Control System which ensures
the best washing result.

Fuzzy Logic Control

When "Punch + 3" washing wings turn, the washing
tub turns in the opposite direction. This makes the
both sides current of water which improve wash­performance by rubbing clothes strongly.

Turbo drum washing (option)

3 step washing makes the best washing performance with low tangling.

3 Step washing

W

O

Rubbing

Rubbing and

Shaking

Shaking and

Disentangling

: Be sure to remove the unit from the carton base, otherwise the machine

will not be able to operate properly.

sensors (Option)

The sensor automatically detects the quantity of a Detergent put by a user and the
temperature and the quality of water to make the best washing algorithm for
washing and rinsing, which can give the best washing effect.

C

ontents

READ THIS MANUAL

Introduction

Before Starting to Wash

Option Programs

Installation

Care and Maintenace

Troubleshooting

Terms of Warranty
Specification

Washing Programs

Inside you will find many helpful hints on how to use and maintain your washer properly.
Just a little preventive care on your part can save you a great deal of time and money over
the life of your washer.
You will find many answers to common problems in the Troubleshooting section. If you
review our chart of Troubleshooting Tips first, you may not need to call for service at all.

Safety Information 4
Identification of Parts 7
Function Information 8
Preparation Before Washing 9
Use of Water, Detergent, Bleach, Softener, Additives

10
Special Guide for Stain Removal 13
Function of each Button 14

Fuzzy Wash (Normal Wash) 16
Heavy Wash 16
Delicates Wash 16
Wool Wash 16
Quick Wash 16
Hand Wash

18
Eco Save Wash 19
Wash Only, Rinse/Spin, Spin Only 20

Soak Wash 21
Delay Start (Reservation) Wash 22
Spin Hold Wash 23

Custom Program 24
Other Useful Functions 25
Placing and Leveling 26
Connecting Water Supply Hose 27
Connecting Drain Hose 30
Grounding Method 31
Cleaning and Maintenance 32
Common Washing Problems 34
Troubleshooting 35
Terms of Warranty 36
Specification 37

4

Introduction

afety Information

S

Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts : Warning and Caution.

: This is a warning sign specifying user’s applications which might

be dangerous.

: This is a sign specifying ‘Strictly Forbidden’ applications.

Warning

: Failure to comply with the instructions under this

sign may result in major physical injuries or death.

Caution

: Failure to comply with the instructions under this

sign may result in minor physical injuries or
damages to the product.

Warning

• Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.

• The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.

• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.

If the product is exposed to such conditions, electric shock, fire, break down or
deformation may occur.

• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.

If not grounded properly, break down and leakage of electricity may occur, which may
cause electric shock.

• Must be positioned so that the plug is accessible.

If the plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.

• Make sure the plug is completely pushed into the outlet.

Failure to do so may cause electric shock and fire due to overheating.

WATER
HEATER
SAFETY

Caution

PROPER
INSTALLATION

S

afety Information

Warning

• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.

Operating with such materials around the machine may trigger
explosion or fire.

• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.

There is potential danger that children might drown in the tub.

Do not touch the power plug with a wet hand.

It will cause electric shock

Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.

There is a rotating mechanism under the machine, so you could be injured.

• Make sure that drainage is working properly.

If water is not drained properly, your floor may get flooded. Flooded floors
may induce electricity leakage, further resulting in electric shock or fire.

• If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.

Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.

Operating with a damaged plug may cause electric shock.

Do not use water hotter than 50°C.

Use of excessively hot water may cause damage to fabrics or cause
leakage of water.

• Use this appliance only for its intended purpose as described in this Owner’s Manual.

• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.

• To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.

YOUR
LAUNDRY
AREA

Caution

WHEN USING
THE WASHER

NOTE : Pressing Power button to turn off does NOT

disconnect the appliance from the power supply.

5

Introduction

6

Introduction

afety Information

S

Warning

Do not use a plug socket and wiring equipment for more than their rated capacity.

Exceeding the limit may lead to electric shock, fire , break down, and/or
deformation of parts.

Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce toxic gases which may cause death.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, dry­cleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.

It may ignite or explode.

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.

• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.

• Wipe off dirt or dust on the contacts of the power plug.

Using unclean power plug may cause fire.

• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.

Children may be trapped and suffocated if the lid is left intact.

Do not attempt to repair or replace any part of this appliance unless specifically
recommended in this Owner’s Manual, or in published user-repair instructions
that you understand and have the skills to carry out.

Operating the machine with improperly replaced parts may be a
cause for fire or electric shock.

Do not tamper with controls.

It may lead to electric shock, fire , break down, deformation.

Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.

Failure to observe these instructions may cause electric shock or fire
due to short-circuit .

When you are cleaning the washing machine, do not apply water directly to any
part of the washing machine.

It will cause short circuit and electric shock.

WHEN USING
THE WASHER

Caution

WHEN NOT
IN USE

7

Introduction

I

dentification of Parts

Accessories

WASHING WINGS
Vertical movement of
washing action can be
operated when a sufficient
amount of laundry is
deposited.
Set the proper water level,
an excessive amount of
water may increase

entanglement of laundry.

HOT WATER SUPPLY
HOSE

COLD WATER SUPPLY
HOSE

Make sure the water
does not leak.

Powder detergent
box for delayed
washing/softener additives box

INLET HOLE FOR
BLEACH

TUB

BASE

LEVELLING LEGS
Use to level the washing
machine for correct balance
& spin operation.

DRAIN HOSE
Check if the drain hose
is hung up before
operating the
washing machine.

FUNCTION SELECTOR

POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer
or its service agents
or similarly qualified
person in order to
avoid a hazard.

LINT FILTER
Clean regularly to stop
linting on the clothes
load.

Drain hose

1 Each for cold and

hot water

or

Inlet hose Cable tie

Body

8

Introduction

F

unction Information

Fuzzy Wash (Normal Wash)

Delicates Wash

Custom Program Wash

Quick Wash

Heavy Wash

Wool Wash

Hand Wash

Soak Wash

Delay Start Wash

Eco Save

Wash Only, Rinse / Spin, Spin Only

Our machine provides various washing methods which suits various conditions and
types of laundry.

Different types of laundry washing

Washing according to the condition of laundry

Other washing method

Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)

Use this program to wash DELICATES and washable laundries. (refer to page 16)

This setting allows you to store your CUSTOM wash conditions in the normal cycle memory. (refer to page 24)

Use this program for load that need pretreatment.
After the prewash of 10 -15 minutes and draining, the washer will run to the nomal wash cycle. (refer to page 18)

Quick wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)

Soak Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove
dirt and grime.(refer to page 21)

Eco Save is the economical program to minimize water consumption. (refer to page 19)

When the user needs only Wash Only, Rinse / Spin, Spin Only. (refer to page 20)

Delay Start Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly.

(refer to page 22)

Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them

Before washing your woolens check the care label for the washing instructions.
When washing woolens use a mild Detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages
(Ensure that the whole article is suitable for machine washing and not just the backing material.)
You may wish to handwash these articles and place them in the machine to spin dry.

Use this Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)

9

Before Starting to Wash

P

reparation Before Washing

Care Labels

Sorting

Check before Loading

Loading

Pretreatment on stains or heavy soil

WARNING

Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

To get the best results, different fabrics need to be washed in different ways.

SOIL (Heavy, Normal, Light) Separate clothes according to the type and amount of soil.
COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors.

Lint Producers Terry cloth, Chenille, Towels, Nappies
Lint Collectors Synthetics, Corduroy, Permanent Press, Socks

Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.

Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.

Pretreat any dirt and stains.

Make sure the clothes are washable in water.
Check the washing instructions.
Remove tissue in pockets.

Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.

(For more detail refer to page 13)

Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).

Load Size

The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in the
washer tub. To add items after washer has started, press Start button and submerge
additional items. Close the lid and press Start button again to restart.

Fire Hazard

Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.

Light and Large-sized clothing

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Do not wash water-proof textilles (Skling outfit, baby's nappy automobile seat covers.)

Long laundry items

Use nylon nets for long, DELICATE items. For laundry with long strings or long length, a net will prevent tangling
during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.

Nylon net is not supplied by LG.

Note

10

Before Starting to Wash

U

se of Water, Detergent, Bleach and Softener, Additives

Amount of WATER LEVEL

Water Temperature

Detergent

Choosing the right Detergent

Using Water

This machine detects the quantity of laundry automatically, then sets the WATER LEVEL.
When you select a wash program, the WATER LEVEL will be shown on the control panel.
The following table shows the amount of water.
When the WATER LEVEL is automatically detected, it may differ depending on the quantity
of laundry even though the same WATER LEVEL is indicated on the control panel.

If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown
or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be
necessary for severe cases.

Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.

We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap
powders should not be used in your washing machine. When washing woolens remember to use Detergent
suitable for washing woolens.

The machine sets the appropriate temperature automatically according to the wash program .
You can change the Water Temperature by pressing the WATER TEMP. button.

The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.
We recommend temperatures of:

- HOT 49~60˚C ...(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items.

- WARM 29~40˚C...(85-105˚F) Most items

- COLD* 18~24˚C ...(65-75˚F) Only very bright colors with light soil.
When washing in COLD water additional steps may be needed:

- Adjust Detergent amount and pre-dissolve Detergent in WARM water

- Pretreat spots and stains

- Soak heavily soiled items

- Use appropriate bleach

*

Temperature below 18˚C...(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29

˚C

...(80-85˚F).

If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.

Using Detergent

11

Before Starting to Wash

Using the Liquid Bleach Dispenser

Using the Dispenser Drawer

The bleach dispenser automatically dilutes and dispenses
liquid chlorine bleach at the proper time in the wash cycle.

1. Check clothing care labels for special instructions.

2. Measure liquid bleach carefully, following instructions on
the bottle.

Never pour undiluted liquid chlorine bleach directly onto
clothes or into the wash basket.
Do not pour powdered bleach into bleach dispenser.
Avoid overfilling or splashing when adding bleach to the
dispenser. The maximum capacity of the bleach
dispenser is one cup of bleach per wash cycle. Overfilling
could result in early dispensing of bleach.

3. Before starting the washer, pour measured amount of
bleach directly into bleach dispenser. If you prefer to use
powdered bleach, add it into the wash basket directly before
adding clothes.

The dispenser drawer contains three compartments:

Liquid Fabric Softener
Liquid or Powder Detergent
Liquid Wash Boost Additives

The dispenser automatically dispenses additives at the
proper time in the wash cycle.

1. Slowly open the dispenser drawer by pulling the drawer out
until it stops.

2. After adding laundry products, slowly close the dispenser
drawer. Closing the drawer too quickly could result in early
dispensing of additives.

Avoid overfilling or splashing when adding laundry
products to the dispenser. Doing so could result in early

dispensing of laundry products.
At the end of the cycle, you may see water in the
compartments. This is part of the normal operation of the
washer.

NOTE: Do not use bleach in the dispenser drawer.

WARNING! Do not mix chlorine bleach with ammonia or acids such as vinegar

and/or rust remover. Mixing can produce a toxic gas which may cause death

The manufacturer's recommended amount of undiluted bleach goes into the bleach dispenser. During the
final "Infusor" wash action the bleach is added to the wash load. This ensures performance won't be
diminished. Two sequential flushe through the bleach dispenser completely removes the bleach from the
dispenser. Any residual liquid left in the dispenser at the end of the cycle is water, not bleach. To prevent
self-siphoning of the bleach into the wash basket and damage to your clothes, never add more than the
maximum fill level marked on the dispenser.
Also keep clothes away from the bleach dispenser so they don't absorb any bleach droplets left around
the bleach dispenser.

12

Before Starting to Wash

U

se of Water, Detergent, Bleach and Softener, Additives

Adding Detergent

Adding Fabric Softener

Adding Wash Boost Additives

Add measured detergent to the detergent
compartment of the dispenser drawer.

Do not exceed the maximum fill line.

Detergent is flushed through the dispenser at
the beginning of the wash phase. Either
powdered or liquid detergent can be used.

Detergent usage may need to be adjusted for
water temperature, water hardness, size and
soil level of the load. Avoid using too much
detergent in your washer, as it can lead to
oversudsing and detergent residue being left
on the clothes.

If desired, pour the recommended amount of
liquid fabric softener into the left-hand
compartment. Use only liquid fabric softener.

Dilute with water to the maximum fill line.

Do not exceed the maximum fill line.

Overfilling can cause early dispensing of the
fabric softener, which could stain clothes.

NOTE: Do not pour fabric softener directly

on the wash load. It may stain the
clothes.

The Wash Boost dispenser may be used to
clean heavily soiled or stained garments more
efficiently.

If desired, place the additives for the wash
Boost setting in the right-hand compartment.
Use only liquid additives.

Do not exceed the maximum fill line to
avoid

Overfilling can cause early dispensing of
presoak additives, which could result in
damaged clothes.

NOTE : Do not pour additives directly on the wash load. It may stain the clothes.

13

Before Starting to Wash

S

pecial Guide for Stain Removal

WARNING

Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.

To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:

Read and comply with all instructions on stain removal products.
Keep stain removal products in their original labeled containers and out of children's reach.
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning
solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames

For successful stain removal:

Remove stains promptly.
Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
To pretreat stains, use a prewash product, liquid Detergent, or a paste made
from granular Detergent and water.
Use COLD water on unknown stains because HOT water can set stains.
Check care label instructions for treatments to avoid on specific fabrics.
Check for colorfastness by testing stain remover on an inside seam.
Rinse and wash items after stain removal.

Stain Removal

STAIN

TREATMENT

Adhesive tape, chewing gum,
rubber cement

Beverages (coffee, tea, soda,
juice, alcoholic beverages)

Blood

Candle wax, crayon

Chocolate
Collar or cuff soil, cosmetics
Dye transfer on white fabric

Grass

Ink

Mildew, scorch

Mud
Mustard, tomato

Nail polish

Paint, varnish
Rust, brown or yellow

discoloration

Shoe polish

Grease, oil, tar (butter, fats,
salad dressing, cooking oils, car
grease, motor oils)

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply nonflammable

dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash using hottest water safe for
fabric.

Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or
nonflammable dry cleaning fluid.

Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.

Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.

Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,

OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and nonchlorine

bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with

prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.

Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonflammable
dry cleaning fluid.

Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using COLD water and bleach safe for fabric.

Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.

Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand
wash to remove solvent. Wash using bleach safe for fabric.

Baby formula, dairy products, egg

Note

14

Before Starting to Wash

F

unction of each Button

POWER BUTTON

SOIL LEVEL BUTTON

Soak, Spin Hold BUTTON

Custom Program
BUTTON

Delay Start (Reservation)
BUTTON

Use to turn the power on or off.

Push again and power goes on or off
The power goes off automatically about 10 seconds
after the wash is finished.

These buttons can be selectable for every
program.

Soak:It gives additional 30 min Soak.
(Except for Wool, Delicate, Rinse/Spin,
Spin Only)

(refer to page 21)

Spin Hold: It gives gentle spin instead of
normal spin (Except for Wool, Delicate,
Wash Only)

(refer to page 23)

Use to set a delayed finishing time.
The time increases when the button is pushed.
The following settings are indicated as the button is
pushed 3 4 5 ... 11 12 14
16 ...46 48 3 HOUR.
To cancel delay time, turn the power switch off.

(refer to page 22)

This button allows
you to store a
customized wash
cycle for future
use .

(refer to page 24)

This button allows you to select
the strength of the wash action.
Power option selections light up
in sequence as follows Medium

Heavy Light Medium as
the button is pushed.
This can be selected for any
program, but when washing
Heavy, it starts with Heavy.
Adjustment can be made while
washing.

* For optimizing the washing algorithm, the displaying time may be changed during washing-increased by 8minutes at

maximum and decreased by 4 minutes at maximum.

* If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically adds

rinsing, and the remaining time may be increased.

* The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to the

washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.

WASHING CONDITION INDICATOR (OPTION)

• It only operates in FUZZY Program.

• During being detected by the sensor, the LED flashes green, orange and red in turn. And,
after detecting, the LED lights a specific color according to the detecting condition as
follows:

If the current washing condition (Detergent quantity, Water Temperature, water quality,
etc.) is determined as better than the standard one, it optimizes the algorithm to save the
energy by decreasing washing time/strength, and the LED automatically turns to red.
If the current washing condition is determined as worse than the standard one, it
optimizes the algorithm by increasing washing time/strength, and the LED
automatically turns to orange.
If the current washing condition is determined as equal to the standard one, the
algorithm has no change and the LED turns to green.

15

Before Starting to Wash

BEEPER BUTTON

START/ PAUSE BUTTON

PROGRAM
BUTTON

WATER LEVEL
BUTTON

WATER TEMP.
BUTTON

This button allows you to adjust the volume of
the Beeper.

Beeper selection light up in sequence as
follows: High

Off Low High

Use to start or pause the washing
process.

Repeats start and pause by pushing the
button.

Use for selecting wash
program.

This button allows you to
select 10 different programs
for different kinds of
laundry and dirtiness.

Program selections light up
in sequence as follows:

Fuzzy

Hand wash
Heavy Delicates
Wool Eco Save
Wash Only Quick Wash

Rinse/Spin Spin only

Fuzzy etc.
Select the desired program
by pressing the button.

Use to select the proper
amount of water in
relation to the weight
and type of laundry.

Controlled
automatically
programs.

Use to select Water (Wash
/Rinse) Temperature.

Pressing the button allows
you to select Cold/Cold
Warm/Cold Hot/Cold
Hot/Warm Warm/Warm

Cold/Cold respectively.

Default setting is Cold/Cold.

* The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a liquid

one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.

* Even if the water level or the water temperature are changed by the user in FUZZY(Normal) Program,

the sensor will still work. The sensor algorithm may differ according to models.

* The control panel may differ according to different models.

CHILD LOCK FUNCTION

Use to lock or unlock the control
buttons to prevent settings from being
changed by a child.

To lock, push the SOIL LEVEL and
WATER TEMP. buttons
simultaneously and to unlock push
them one more time during the
washing process.

(refer to page 25)

1 2 4

21 3 5

21 3 5

21 3 5

21 3 5

16

Washing Programs

W

ashing programs

Washing

Programs

Fuzzy Wash

(Normal Wash)

Used for normal loads, this
mode automatically selects
the most appropriate
conditions and completes the
sequence in one operation.
The built-in sensor detects the
size of the load and the ideal
wash power and wash, rinse
and spin times are set
accordingly.

The detergent should
be used according to
the instruction of the
detergent manufacture.

Select the

Quick Wash

program on
the Control
panel.

Select the

Heavy

program on
the Control
panel.

Use neutral Detergent
appropriate for the
laundry.
When washing woolens
use a mild Detergent
recommended for
washing wool.

Select the

Delicates

program on
the Control
panel.

Select the

Wool

program on
the Control
panel.

The detergent should
be used according to
the instruction of the
detergent
manufacture.

Quick Wash

Use this mode when washing
lightly soiled clothes for a
short time. The highly
recommended laundry
amount is under 2.0kg.

Heavy Wash

Use HEAVY program when
washing Jeans of different
sizes.

Wool Wash

Use this program for washing
delicate fabrics such as
lingerie and woolens. (wash
only “water washable”
clothes)
Before washing your woolens
check the care label for the
washing instructions.
(wash only water washable
clothes)

Delicates

Use this program to wash
items requiring a GENTLE
WASH action. This would
include blouses, nylons and
dress shirts with light soiled.

Add

the

laundry

Add

the Detergent

3 5 6

4 6 7

4 6 7

4 6 7

4 6 7

17

Washing Programs

If water is already in the tub, or
putting wet laundry into the tub
before starting will increase the
WATER LEVEL.
With lightweight bulky loads,
WATER LEVEL can be set low.
Changes to Water Temperature
(refer to page 15) and wash level are
possible during operation.

When setting the WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
Washing with HOT water may
damage the laundry .
Ensure that the load is under 2kg.
In order to avoid damage to laundry,
the spin cycle may appear slow. This
also avoids wrinkles and clothing may
still contain some water. This is
normal.

Before starting to wash, make sure that
the laundry is washable.
Washing with HOT water may
damage the laundry.
Ensure that the load is under 2kg.

The pulsator rotates for
8 seconds to detect the
laundry load.
Then the WATER
LEVEL
will be shown and
water will be supplied.

Water will be
supplied for 2
minutes after the
start of the wash to
supplement the
water the laundry
has absorbed.

When the wash
program ends, the
buzzer will ring for
10 seconds before
the Power goes off
automatically.

Close the lid

Finish

Caution & Note

Note

18

Washing Programs

H

and Wash

1

2

3

4

5

After the prewash of 10~15 minutes and draining, the washer will run to
the normal wash cycle.

Press the POWER button to turn power on.

Press the PROGRAM button to select Hand Wash program.

Add the laundry into the washing tub.

Press the

START/PAUSE button.

Add the Detergent and close the lid.

Fabric
Softner

Detergent for
main wash

Additives
Hand Wash (pre wash)

• Hand Wash program takes longer washing time than Fuzzy (Normal) program.

Note

19

E

co Save Wash

1

2

4

5

Press the PROGRAM button to select Eco Save program.

3

Add the laundry into the washing tub.

Press the

START/PAUSE button.

Add the Detergent and close the lid.

Left time is displayed.

When the lid is open the machine will not operate, and an alarm signal will remind you to
close the lid.

Eco Save can handle all types of clothes that the Fuzzy (Normal) course can do.

Eco Save is the economical program to minimize water consumption.

Press the POWER button to turn power on.

Washing Programs

20

1

2

3

4

5

6

When you only need the Wash, Rinse/Spin or Spin cycles, these can be set manually.

Press the POWER button to turn power on.

Press the

PROGRAM button for desired option.

Press the

WATER LEVEL button. (Except for Spin Only)

Add the laundry into the washing tub.

Press the

START/PAUSE button.

Add the detergent (Except for

Spin Only) if required and close the lid.

When you want to only drain, wait until the water in the washing tub drains
completely and then turn off the power

Control the water level according to the amount of laundry.

Wash Only, Rinse/Spin, Spin Only

W

ash Only, Rinse/Spin, Spin Only

Washing Programs

21

Option Programs

S

oak Wash

1

2

3

4

5

6

Press the POWER button to turn power on.

Press the PROGRAM button to select the washing program.

Press the

Soak button.

Add the Detergent.

Add the laundry and press the

START/PAUSE button.

Close the lid.

Finish

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty.
Soak mode can be used with

Fuzzy, Hand Wash, Heavy, Eco Save, Wash only, Quick Wash

program.

The WATER LEVEL and be used will be shown
and water will be supplied.

Water will be supplied for 2 minutes after the start
of the wash to supplement the absorbed water by
the laundry.

When the wash program ends, the buzzer will ring
for 10 seconds before the Power goes off
automatically.

Note

22

Option Programs

D

elay Start (Reservation) Wash

1

2

3

4

5

6

Press the POWER button to turn power on.

Press the PROGRAM button to select the washing program.

Press the

Delay Start (Reservation) button.

Add the Detergent.

Delay Start (Rreservation) Wash is used to delay the finishing time of the operation. The
hours to be delayed can be set by the user accordingly. The time on the display is the
finishing time, not the start time.

Select the program for laundry on the Control panel.
This program will not work in

Wool, Delicate and Spin Only

Program.

When the lid is open the machine will not operate, and an alarm
signal will remind you to close the lid

The light will ‘ Delay’ turn on and ‘TIME LEFT’ will be
marked.

Press the button repeatedly to set the desired finishing time. For
example, To finish washing in 9 hours from now, by make the number

9:00 pressing the Delay Start (Reservation ) button repeatedly.

(RES.=Delay)

Add the laundry and press the START/PAUSE button.

Close the lid.

Finish

When you press the START/PAUSE button the light will
blink.

Water will be supplied for 2 minutes after the start of the wash to
supplement the water the laundry has absorbed.

The washing will be finished according to the delayed time.

Finishing time can be delayed from 3~48 hours. Delaying from 3~12 hours can be done in 1 hour time intervals and
from 12~48 hours in 2 hour time intervals.
If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.
To select water level, water temp. or soil level manually, press the Delay Start (Reservation) button and select the
desired option. Then press the START/PAUSE button.
When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning
program. (The laundry will be wrinkled if left for a long time after spinning.)

Note

23

Option Programs

S

pin Hold Wash

1

2

3

5

6

Press the POWER button to turn power on.

Press the PROGRAM button to select the washing program.

Press the

Spin Hold button to select gentle spin instead of normal spin.

4

Add the laundry into the washing tub.

This Program gives gentle spin instead of normal spin.

Add the Detergent and close the lid.

Press the

START/PAUSE button.

To smooth out wrinkles, spin rpm is lower than normal spinng rpm. So the laundry has more moisture than
normal.