LG WFT11C65DF Owner's Manual

Washing Machine
OWNER'S MANUAL
Please read this manual carefully before operating your set. Retain it for future reference. Record model name and serial number of the set. Quote this information to your dealer when you require service.
MODEL : WFT(R,N,S,C,F)10(1)C64(5)D(E)C(H,P,D,E,F,M) WFT15C65EF WFT15C65EFS WF-T1250TD WF-T1391TP WF-TS1688TC WF-TS1400 LWD-13C65EF
roduct Features
P
FUZZY logic control
A built-in load sensor automatically detects the laundry load and a microprocessor optimizes washing conditions such as ideal WATER LEVEL and washing time.
Advanced technology is built into the Electronic Control System which ensures the best washing result.
Turbo drum washing
(option)
When "Punch + 3" washing wings turn, the washing tub turns in the opposite direction. This makes the both sides current of water which improve wash­performance by rubbing clothes strongly.
Applied models : WFT
Washer doesn't operate while the lid is open. If the lid is open during the wash, rinse or spin cycles, the operation stops for safety.
3 Step washing
3 step washing makes the best washing performance with low tangling.
sensors
(option)
The sensor automatically detects the quantity of a Detergent put by a user and the temperature and the quality of water to make the best washing algorithm for washing and rinsing, which can give the best washing effect.
Rubbing
Rubbing and
Shaking
Shaking and
Disentangling
NOTE :
Be sure to remove the unit from the carton base, otherwise the machine will not be able to operate properly.
SENSING
SETTING
Laundry Sensor
START
Water Level Sensor
Optimum Washing Condition
WASHING
AUTO
POWER
OFF
C
ontents
Introduction
Before Starting to Wash
Washing Programs
Additional Function Program
Installation
Care and Maintenance
T r oub leshooting
Terms of Warranty Specification
Safety Information Identification of Parts Function Information Preparation Before Washing Use of Water, Detergent, Bleach and Softener Special Guide for Stain Removal Function of each Button FUZZY Wash (Normal Wash) QUICK WASH JEAN Wash WOOL Wash DELICATE SOAK Wash FAVORITE Wash SILENT TUB CLEAN AIR DRY Option Washing DELAY START (RESERVATION) Wash Other Useful Functions Placing and Leveling Connecting Water Supply Hose Connecting Drain Hose Grounding Method Cleaning and Maintenance Common washing problems Troubleshooting Terms of Warranty Specification
4 7 8
9 10 13 14 16 16 16 16 16 18 19 20 21 22 23 24 25 26 27 30 31 32 34 35 36 37
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.
afety Information
S
4
Introduction
Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
Warning
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
Caution
: Failure to comply with the instructions under this
sign may result in minor physical injuries or damages to the product.
Warning
• Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances. If the HOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.
• The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.
• Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
WATER HEATER SAFETY
Caution
PROPER INSTALLATION
S
afety Information
5
Introduction
Warning
• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger explosion or fire.
• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving. Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or cause leakage of water.
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
YOUR LAUNDRY AREA
Caution
WHEN USING THE WASHER
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
afety Information
S
6
Introduction
Warning
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, dry­cleaning solvents, kerosene, etc). Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.
It will cause short circuit and electric shock.
WHEN USING THE WASHER
Caution
WHEN NOT IN USE
I
dentification of Parts
7
Introduction
WATER SUPPLY HOSE
POWDER DETERGENT AND SOFTENER BOX
BLEACH DISPENSER
FUNCTION SELECTOR
TUB
BASE
ADJUSTABLE LEGS
DRAIN HOSE for pump model
DRAIN HOSE
POWER PLUG
LINT FILTER
START/PAUSE BUTTON
Use to start or stop the washing machine temporarily.
Make sure the water does not leak.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.
Clean regularly to stop linting on the clothes load.
Check if the drain hose is hung up before operating the washing machine.
for non pump model
Use to level the washing machine for correct balance & spin operation.
Body
Part can be different according to the model.
NOTE
Drain hose Anti-rat cover (option)
Water supply hoses
or
or
1 Each for COLD and
HOT water
Accessories
unction Information
F
8
Introduction
Our machine provides various washing methods which suits various conditions and types of laundry.
FUZZY(Normal) Wash
JEAN Wash
WOOL Wash
QUICK WASH
SOAK Wash
DELAY START Wash
OPTION WASH
Use this Program for everyday washing e.g. sheets, towels, T-shirts.
(refer to page 16)
DELICATE Wash
Use this program to wash DELICATE and washable laundries.
(refer to page 16)
FAVORITE Wash
This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)
SILENT Wash
Use this program to wash quietly at night. (refer to page 20)
Use this Program for heavily soiled durable garments e.g. overalls, jeans. Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)
Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16) The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
Before washing your woolens check the care label for the washing instructions.
When washing woolens use a mild Detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.) Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to handwash these articles and place them in the machine to spin dry.
QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)
SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 18)
DELAY START Wash is used to delay the finishing time of the operation. The number of hours to be delayed can be set by the user accordingly. (refer to page 24)
When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN, SOAK/WASH/RINSE/SPIN. (refer to page 23)
TUB CLEAN
Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 21)
Washing according to the condition of laundry
Other washing method
Different types of laundry washing
P
reparation Before Washing
9
Before Starting to Wash
Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
Pretreat any dirt and stains.
Make sure the clothes are washable in water.
Check the washing instructions.
Remove tissue in pockets.
To get the best results, different fabrics need to be washed in different ways.
SOIL (Heavy, Normal, Light)
Separate clothes according to the type and amount of soil.
COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers Lint Collectors Synthetics, Corduroy, Permanent Press, Socks
WIRE
Sorting
Check before Loading
* Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed. Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Care Labels
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing.
Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Light and Large-sized clothing
Long laundry items
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.
Loading
Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
Use a pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page13)
Pretreatment on stains or heavy soil
Fire Hazard
Never place items in the washer that are dampened with gasoline or other flammable fluids. No washer can completely remove oil. Do not dry anything that has ever had any type of oil on it (including cooking oils). Doing so can result in death, explosion, or fire.
WARNING
10
Before Starting to Wash
se of Water, Detergent, Bleach and Softener
U
The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results. We recommend temperatures of:
- HOT 49~60°C…(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items.
- WARM 29~40°C…(85-105˚F) Most items
- COLD* 18~24°C…(65-75˚F) Only very bright colors with light soil.
When washing in COLD water additional steps may be needed:
- Adjust Detergent amount and pre-dissolve Detergent in WARM water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach
* Temperature below 18°C…(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29°C…(80-85˚F). If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems. Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to use Detergent suitable for washing woolens.
Water Temperature
Using Water
The machine sets the appropriate temperature automatically according to the wash program .
You can change the Water Temperature by pressing the WATER TEMP. button. (refer to page 14)
This machine detects the quantity of laundry automatically, then sets the
WATER LEVEL and proper amount of Detergent.
When you select a wash program, the WATER LEVEL and amount of
Detergent (to be used) will be shown on the control panel.
The following table shows the amount of water.
When the WATER LEVEL is automatically detected, it may differ depending
on the quantity of laundry even though the same WATER LEVEL is indicated on the control panel.
The amount of a cup in the diagram is about 40g for concentrated Detergent.
Amount of WATER LEVEL
NOTE
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.
NOTE
[ Minimum water amount ]
It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to some height. Thats because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.
Open the Detergent dispenser and deposit the appropriate amount of Detergent where you deposit the Detergent Powder Detergent dispenser. Some Detergents MUST be fully dissolved before adding to your machine to get the best wash results. Check the instructions on the Detergent packet. If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water before being added to WARM or HOT water for the actual wash. Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance.
11
Before Starting to Wash
Using Detergent
How much Detergent
When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent. The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work cloches may need more Detergent, while bath towels usually need less.). For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about half­way through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine. If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, so use it accordingly.
Adding the Detergent
Check clothing care label for special instructions and separate the laundry to be bleached
Dilute liquid chlorine bleach.
Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
Before starting the washer, pour measured amount of bleach directly into bleach dispenser. Avoid splashing or overfilling. Powdered bleach should be mixed with water before pouring.
Using Liquid Bleach
Bleach dispenser
NOTE
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
Do not pour powdered bleach into bleach dispenser.
Powder Detergent / F abric Softener dispenser.
Where you deposit the detergent
se of Water, Detergent, Bleach and Softener
U
12
Before Starting to Wash
Using Fabric Softener
If you wish to use fabric softener we recommend
NOTE
Fabric Softener will be inserted automatically during the final rinse and the machine gives on alarm sound. When water pressure is low, the softener may have to be inserted manually.
Do not use concentrated fabric softener. This may cause some problems in automatic dispensing.
For more details refer to the softener products instructions for use.
Scrud(Waxy Build up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.
Using fabric softener sparingly.
When filling the dispenser, do not splash or overfill.
Clean dispenser as soon as the cycle is finished.
Clean your machine regularly. (refer to page 21 or 32)
Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or
HOT wash e.g. every 5th wash should be at least a warm one.
Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.
Available Fabric Softener Type
Don't use softener with detergent. Use softener in last rinse water
When using dispenser, dilute softener (30ml) with fresh water (30ml)
When filling dispenser, do not splash or overfill. It may stain clothes.
Never pour fabric softener directly on clothes. It may stain them
If spotting occurs, wet and rub with hand dishwashing liquid (or mild bar soap) and rewash.
Depositing Fabric Softener
Powder Detergent / F abric Softener dispenser.
If the softener is over filled, it can overflow.
Where you deposit the softener
Fabric Softener Cap
Limit Line
Depositing liquid don’t fill it above the limit line.
Loading...
+ 27 hidden pages