LG WF-T1153TP Owner's Manual

Washing Machine

OWNER'S MANUAL

MODEL :

WF-T1153TP

P/No. : 3828EY3068L

roduct Features

Washer doesn't operate while the lid is open. If the lid is open during the wash, rinse or spin cycles, the operation stops for safety.

●

The sensor automatically detects the quantity of a Detergent put by a user and the temperature and the quality of water to make the best washing algorithm for washing and rinsing, which can give the best washing effect.

FUZZY logic control

●

A built-in load sensor automatically detects the laundry load and a microprocessor optimizes washing conditions such as ideal WATER LEVEL and washing time.

●

Advanced technology is built into the Electronic Control System which ensures the best washing result.

Turbo drum washing (option)

●

When "Punch + 3" washing wings turn, the washing tub turns in the opposite direction. This makes the both sides current of water which improve washperformance by rubbing clothes strongly.

sensors (option)

SENSING

SETTING

Laundry Sensor

Water Level Sensor

Optimum Washing Condition

WASHING

START

Applied models : WFT

AUTO

POWER

OFF

3 Step washing

●

3 step washing makes the best washing performance with low tangling.

Rubbing

NOTE

Rubbing and

Shaking

Be sure to remove the unit from the carton base, otherwise the machine will not be able to operate properly.

Shaking and

Disentangling

ontents

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.

Introduction

Before Starting to Wash

Washing Programs

Additional Function Program

Installation

Care and Maintenance

Troubleshooting

Terms of Warranty

Specification

Safety Information Identification of Parts Function Information Preparation Before Washing Use of Water, Detergent, Bleach and Softener Special Guide for Stain Removal Function of each Button FUZZY Wash (Normal Wash) QUICK WASH JEAN Wash WOOL Wash DELICATE SPEEDY SOAK Wash FAVORITE Wash SILENT Wash TUB CLEAN DELAY START (RESERVATION) Wash Option Other Option Washing Other Useful Functions Placing and Leveling Connecting Water Supply Hose Connecting Drain Hose Grounding Method Cleaning and Maintenance Common washing problems Troubleshooting Terms of Warranty Specification

4 7 8

9 10 13 14 16 16 16 16 16 18 19 20 21 22 23 24 25 26 27 30 31 32 34 35 36 37

itle

afety Information

Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts : Warning and Caution.

Introduction

WATER HEATER SAFETY

PROPER INSTALLATION

: This is a warning sign specifying user’s applications which might

be dangerous.

: This is a sign specifying ‘Strictly Forbidden’ applications.

Warning

Caution

: Failure to comply with the instructions under this

sign may result in major physical injuries or death.

: Failure to comply with the instructions under this

sign may result in minor physical injuries or damages to the product.

Warning

• Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances. If the HOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

Caution

• The base opening must not be obstructed by carpeting when the washing machine is installed on a

carpeted floor.

• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.

If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.

• Properly ground washer to conform with all governing codes and ordinances. Follow details in

Installation Instructions.

If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.

• Must be positioned so that the plug is accessible.

If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.

• Make sure the plug is completely pushed into the outlet.

Failure to do so may cause electric shock and fire due to overheating.

afety Information

Introduction

YOUR LAUNDRY AREA

WHEN USING THE WASHER

Warning

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.

Operating with such materials around the machine may trigger explosion or fire.

• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.

There is potential danger that children might drown in the tub.

Do not touch the power plug with a wet hand.

It will cause electric shock

Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.

There is a rotating mechanism under the machine, so you could be injured.

Caution

• Use this appliance only for its intended purpose as described in this Owner’s Manual.

• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.

NOTE : Pressing Power button to turn off does NOT

disconnect the appliance from the power supply.

• Make sure that drainage is working properly.

If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.

• If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving. Wait until the machine has completely stopped before opening the lid.

Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

Operating with a damaged plug may cause electric shock.

Do not use water hotter than 50°C.

Use of excessively hot water may cause damage to fabrics or cause leakage of water.

afety Information

WHEN USING THE WASHER

Introduction

WHEN NOT IN USE

Warning

Do not use a plug socket and wiring equipment for more than their rated capacity.

Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.

Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce toxic gases which may cause death.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation.

It may ignite or explode.

Caution

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.

• When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.

• Wipe off dirt or dust on the contacts of the power plug.

Using unclean power plug may cause fire.

• Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.

Children may be trapped and suffocated if the lid is left intact.

Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.

Operating the machine with improperly replaced parts may be a cause for fire or electric shock.

Do not tamper with controls.

It may lead to electric shock, fire , break down, deformation.

Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.

Failure to observe these instructions may cause electric shock or fire due to short-circuit .

When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.

It will cause short circuit and electric shock.

dentification of Parts

WATER SUPPLY HOSE

POWDER DETERGENT BOX

BLEACH DISPENSER

FUNCTION SELECTOR

TUB

BASE

ADJUSTABLE LEGS

DRAIN HOSE for pump model

DRAIN HOSE

POWER PLUG

LINT FILTER

START/PAUSE BUTTON

Use to start or stop the washing machine temporarily.

Make sure the water does not leak.

If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.

Clean regularly to stop linting on the clothes load.

Check if the drain hose is hung up before operating the washing machine.

for non pump model

Softner will automatically flow into the tub.

SOFTENER INLET

Body

Introduction

Accessories

Water supply hoses

1 Each for COLD and

HOT water

Note

Part can be different according to the model.

Drain hose Anti-rat cover (option)

unction Information

Our machine provides various washing methods which suits various conditions and types of laundry.

Different types of laundry washing

FUZZY(Normal) Wash

Use this Program for everyday washing e.g. sheets, towels, T-shirts.

Introduction

Washing according to the condition of laundry

Other washing method

JEAN Wash

Use this Program for heavily soiled durable garments e.g. overalls, jeans. Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)

DELICATE Wash

Use this program to wash DELICATE and washable laundries.

WOOL Wash

Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16) The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed. Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them

• Before washing your woolens check the care label for the washing instructions.

• When washing woolens use a mild Detergent recommended for washing wool.

• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.

• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)

Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to handwash these articles and place them in the machine to spin dry.

FAVORITE Wash

This setting allows you to store your FAVORITE wash conditions in the normal cycle memory.

SILENT Wash

Use this program to wash quietly at night.

QUICK WASH

QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time.

SPEEDY SOAK Wash

SPEEDY SOAK Wash is designed to maximize washing performance and can be selected to wash heavily soiled laundry with FUZZY or JEAN Program.

TUB CLEAN

Use this program to clean the inside of washing machine especially Inner tub & Outer tub .

DELAY START Wash

DELAY START Wash is used to delay the finishing time of the operation. The number of hours to be delayed can be set by the user accordingly.

OPTION

One or more OPTION can be selected for GENTLE SPIN and EXTRA RINSE ad AIR DRY

(refer to page 20)

(refer to page 16)

(refer to page 19)

(refer to page 16)

(refer to page 18)

(refer to page 21)

(refer to page 22)

(refer to page 23)

OPTION WASH

When the user needs only WASH/RINSE/SPIN, SPEEDY SOAK/WASH/RINSE/SPIN, SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH.

(refer to page 24)

WIRE

reparation Before Washing

Care Labels

* Look for a care label on your clothes. This will tell you about the fabric content of your garment

and how it should be washed. Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

Sorting

To get the best results, different fabrics need to be washed in different ways.

• SOIL (Heavy, Normal, Light)

• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.

• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.

Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers Lint Collectors Synthetics, Corduroy, Permanent Press, Socks

Check before Loading

• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,

pens, coins, and keys can damage both your washer and your clothes.

• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.

• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.

• Pretreat any dirt and stains.

• Make sure the clothes are washable in water.

• Check the washing instructions.

• Remove tissue in pockets.

Pretreatment on stains or heavy soil

• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

• Use a pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.

(For more detail refer to page13)

Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).

Load Size

The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.

Light and Large-sized clothing

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Long laundry items

Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing.

Nylon net is not supplied by LG.

Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.

Separate clothes according to the type and amount of soil.

WARNING

Never place items in the washer that are dampened with gasoline or other flammable fluids. No washer can completely remove oil. Do not dry anything that has ever had any type of oil on it (including cooking oils). Doing so can result in death, explosion, or fire.

Fire Hazard

Before Starting to Wash

se of Water, Detergent, Bleach and Softener

Using Water

Amount of WATER LEVEL

• This machine detects the quantity of laundry automatically, then sets the WATER LEVEL and proper amount of Detergent.

• When you select a wash program, the WATER LEVEL and amount of Detergent (to be used) will be shown on the control panel.

• The following table shows the amount of water.

• When the WATER LEVEL is automatically detected, it may differ depending on the quantity of laundry even though the same WATER LEVEL is indicated on the control panel.

• The amount of a cup in the diagram is about 40g for concentrated Detergent.

NOTE

[ Minimum water amount ]

It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to some height. That’s because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.

Water Temperature

• The machine sets the appropriate temperature automatically according to the wash program .

• You can change the Water Temperature by pressing the WATER TEMP. button. (refer to page 14)

• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.

We recommend temperatures of:

- HOT 49~60°C…(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items.

- WARM 29~40°C…(85-105˚F) Most items

- COLD* 18~24°C…(65-75˚F) Only very bright colors with light soil.

• When washing in COLD water additional steps may be needed:

- Adjust Detergent amount and pre-dissolve Detergent in WARM water

- Pretreat spots and stains

- Soak heavily soiled items

- Use appropriate bleach

* Temperature below 18°C…(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.

In addition, Detergent manufactures and care labels define COLD water as 26~29°C…(80-85˚F). If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.

NOTE

If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.

Using Detergent

Detergent

Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems. Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.

Choosing the right Detergent

We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to use Detergent suitable for washing woolens.

Using Detergent

How much Detergent

When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent. The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work cloches may need more Detergent, while bath towels usually need less.). For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.

Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine. If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, so use it accordingly.

Adding the Detergent

Before Starting to Wash

Open the Detergent dispenser and deposit the appropriate amount of Detergent where you deposit the Detergent Powder Detergent dispenser. Some Detergents MUST be fully dissolved before adding to your machine to get the best wash results. Check the instructions on the Detergent packet. If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water before being added to WARM or HOT water for the actual wash. Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance.

Where you

Dónde

deposit the

deposita el

Detergent

detergente

Using Liquid Bleach

• Check clothing care label for special instructions and separate the laundry to be bleached

• Dilute liquid chlorine bleach.

• Measure the recommended amount of liquid bleach carefully following instructions on the bottle.

• Before starting the washer, pour measured amount of bleach directly into bleach dispenser. Avoid splashing or overfilling. Powdered bleach should be mixed with water before pouring.

Powder Detergent Box

Dispensador de detergente en polvo.

( )

Bleach dispenser

( )

Attention

■ Never pour undiluted liquid bleach directly onto clothes or into the wash basket. This may cause change of color or damage the laundry.

■ Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can reduce a toxic gas which may cause death.

■ Do not pour powdered bleach into bleach dispenser.

Using Fabric Softener

• Dilute fabric softener with water. Undiluted fabric softener may result in spots that look like oil stains.

• Measure and add the recommended amount of fabric softener

Before Starting to Wash

into the compartment marked with this symbol( ). Follow manufacturer’s direction.

• Do not overfill. The dispenser hold max 35mL. Never add more than 35mL. Overfilling can cause early dispensing of the fabric softener which could result in stained clothes. A cup with a pouring spout will help you avoid spilling.

• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually put during the time when the washer beeps several times before the final rinse. This function informing correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric softener has to be diluted with water before dispensed and never poured directly on clothes.

se of Water, Detergent, Bleach and Softener

Softener dispenser ( )

Fabric softener is automatically dispensed in the final rinse with indication beep.

If you want EXTRA RINSE, you must add fabric softener manually when indication beep rings in the final rinse. This maximize the fabric softener function.

Attention

■ Do not mix with Detergent or bleach.

■ Never pour fabric softener directly on clothes. It may stain them.

■ Do not stop the washer during the first spin for timely dispensing.

■ Option washing is not designed to be used with fabric softener dispenser.

Scrud(Waxy Build up)

Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.

If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.

If you wish to use fabric softener we recommend

• Using fabric softener sparingly.

• When filling the dispenser, do not splash or overfill.

• Clean dispenser as soon as the cycle is finished.

• Clean your machine regularly. (refer to page 21 or 32)

• Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or HOT wash e.g. every 5th wash should be at least a warm one.

• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.

pecial Guide for Stain Removal

WARNING

■

Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.

■

To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:

• Read and comply with all instructions on stain removal products.

• Keep stain removal products in their original labeled containers and out of children’s reach.

• Thoroughly wash any utensil used.

• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.

• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.

• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.

For successful stain removal:

• Remove stains promptly.

• Determine the kind of stain, then follow the recommended treatment in the stain removal chart below.

• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.

• Use COLD water on unknown stains because HOT water can set stains.

• Check care label instructions for treatments to avoid on specific fabrics.

• Check for colorfastness by testing stain remover on an inside seam.

• Rinse and wash items after stain removal.

Stain Removal

STAIN

Adhesive tape, chewing gum, rubber cement

Baby formula, dairy products, egg Beverages (coffee, tea, soda, juice,

alcoholic beverages) Blood

Candle wax, crayon

Chocolate Collar or cuff soil, cosmetics Dye transfer on white fabric Grass

Grease, oil, tar (butter, fats, salad dressing, cooking oils, car grease, motor oils)

Ink

Mildew, scorch Mud

Mustard, tomato Nail polish

Paint, varnish

Rust, brown or yellow discoloration

Shoe polish

Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonflammable dry cleaning fluid.

Use product containing enzymes to pretreat or soak stains. Pretreat stain. Wash using COLD water and bleach safe for fabric. Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using

bleach safe for fabric. Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.

Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Pretreat with prewash stain remover or rub with bar soap. Use packaged color remover. Wash using bleach safe for fabric. Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply

nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash using hottest water safe for fabric.

Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or nonflammable dry cleaning fluid.

Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly mildewed fabrics may be permanently damaged.

Brush off dry mud. Pretreat or soak with product containing enzymes. Pretreat with prewash stain remover. Wash using bleach safe for fabric. May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.

Repeat, replacing paper towels frequently. Do not use on acetate fabrics. WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,

OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing. For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and

nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration. LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with

prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach safe for fabric.

TREATMENT

Follow fabric care label

instructions

Before Starting to Wash

unction of each Button

WATER TEMPERATURE BUTTON (OPTION)

Use to select Water Temperature. Pressing the button allows you to select COLD WARM (HOT&COLD) HOT COLD respectively. Default setting is COLD.

Before Starting to Wash

OPTION BUTTON

• According to kinds of laundry, Air Dry, soiled extent or washing habit you can select suitable OPTION manually.

• By pressing the button OPTION is changed.

(refer to page 23)

DELAY START (RESERVATION) BUTTON

• Use to set a delayed finishing time.

• The time increases when the button is pushed.

• The following settings are indicated as the button is pushed 3 4 5 ...11 12 14 16 ...46 48

3 HOUR.

• To cancel delay time, turn the power switch off.

(refer to page 22)

WATER LEVEL BUTTON (INDICATION OF DETERGENT AMOUNT)

• Use to adjust the WATER LEVEL as required. The appropriate amount of Detergent is shown next to the WATER LEVEL in the WATERDETERGENT diagram

•

WATER LEVEL is automatically selected for FUZZY (normal) program. The following settings are indicated as the button is pushed LARGE LARGE .EX-LARGE EX-LARGE SMALL

MEDIUM MEDIUM MEDIUM LARGE LARGE

SMALL

WASHING CONDITION INDICATOR (OPTION)

• It only operates in FUZZY Program.

• During being detected by the sensor, the LED flashes green, orange and red in turn. And, after detecting, the LED lights a specific color according to the detecting condition as follows:

If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength, and the LED automatically turns to red. If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by increasing washing time/strength, and the LED automatically turns to orange. If the current washing condition is determined as equal to the standard one, the algorithm has no change and the LED turns to green.

Note

* For optimizing the washing algorithm, the displaying time may be changed during washing-increased by

8minutes at maximum and decreased by 4 minutes at maximum.

* If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically

adds rinsing, and the remaining time may be increased.

* The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to

the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.

* The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a

liquid one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.

Before Starting to Wash

TIME LEFT, DELAY START (RESERVATION), ALARM INDICATION

• Time left - During operation, the remaining time is indicated.

• DELAY START INDICATION (RESERVATION) - When

DELAY START (RESERVATION) program is selected, it indicates the finishing time. (RES.=DELAY)

• Alarm indication -When an error occurs, an error message

appears to indicate the abnormality. For example, indicates that the lid is open.

PROCESS BUTTON

• Use to select SPEEDY SOAK, Wash, Rinse and Spin functions as desired.

CHILD LOCK FUNCTION

• Use to lock or unlock the control buttons to prevent settings from being changed by a child. To lock, push the PROCESS and PROGRAM buttons simultaneously and to unlock push them one more time during the washing process.

(refer to page 25)

START/ PAUSE BUTTON

• Use to start or pause the washing process.

• Repeats start and pause by pushing the button.

AUTO OFF (POWER) BUTTON

• Use to turn the power on or off.

• Push again and power goes on or off

• The power goes off automatically about 10 seconds after the wash is finished.

PROGRAM BUTTON

• Use for selecting wash program.

• This button allows you to select 4 different programs for different kinds of laundry and dirtiness.

• program selections light up in sequence as follows: FUZZY (NORMAL) DELICATE QUICK WASH JEAN WOOL SILENT FAVORITE TUB CLEAN

(NORMAL)

FUZZY desired program by pressing the button.

etc. Select the

* Because the detecting ability of the sensor may be decreased by using it for a long time, periodically use

TUB CLEAN course to clean the tub. (refer to page 21)

* Even if the water level or the water temperature are changed by the user in FUZZY(Normal) Program,

the sensor will still work. The sensor algorithm may differ according to models.

* The control panel may differ according to different models.

s R

ashing Programs

Washing Programs

Washing

Programs

FUZZY Wash

(Normal Wash)

Used for normal loads, this mode automatically selects the most appropriate conditions and completes the sequence in one operation. The built-in sensor detects the size of the load and the ideal wash power and wash, rinse and spin times are set accordingly.

QUICK WASH

Use this mode when washing lightly soiled clothes for a short time.

JEAN Wash

Use Jean program when washing Jeans of different sizes

Add

the

laundry

Spread the jean evenly in the tub

Select the

QUICK WASH

program on the Control panel.

Select the JEAN program on the Control panel.

Add

the Detergent

Add the appropriate quantity of Detergent as indicated by the WATER LEVEL next to

WATER DETERGENT.

Or follow the Detergent manufacturer’s instruction

Add the appropriate quantity of Detergent a indicated by the WATE LEVEL next to

WATER DETERGENT.

Or follow the Detergen manufacturer’s instructions

Use this program for washing delicate

WOOL Wash

fabrics such as lingerie and woolens. (wash only “water washable” clothes) Before washing your woolens check the care label for the washing instructions. (wash only water washable clothes)

DELICATE

Use this program to wash items requiring a GENTLE WASH action. This would include blouses, nylons and dress shirts with light soiled.

Select the

WOOL

program on the Control panel.

Select the

DELICATE

program on the Control panel.

Use neutral Detergent appropriate for the laundry. When washing woolens use a mild Detergent recommend- ed for washing wool.

Close the lid Finish Caution & Note

Washing Programs

The pulsator rotates for 8 seconds to detect the laundry load. Then the WATER LEVEL and the amount of Detergent to be used will be shown and water will be supplied.

Water will be supplied for 2 minutes after the start of the wash to supplement the water the laundry has absorbed.

When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.

If water is already in the tub, or putting wet laundry into the tub before starting will increase the WATER LEVEL. With lightweight bulky loads, WATER LEVEL can be set low. Changes to Water Temperature (HOT/COLD) and wash level are possible during operation.

(refer to page 14)

The highly recommended laundry amount is under

2.0kg.

When setting the WATER LEVEL manually, do not set to Medium to prevent damage to laundry.

Washing with HOT water may damage the laundry (Water is set to cold automatically). Ensure that the load is under 2kg.

In order to avoid damage to laundry, the spin cycle may appear slow. This also avoids wrinkles and clothing may still contain some water. This is normal.

If WOOL wash is selected, GENTLE SPIN will be set automatically.

Before starting to wash, make sure that the laundry is washable.

Washing with HOT water may damage the laundry (Water is set to COLD automatically). Ensure that the load is under 2kg.

Washing Programs

PEEDY SOAK Wash

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty. SPEEDY SOAK mode can be used with FUZZY or JEAN program.

Press the AUTO OFF (POWER) button to turn power on.

Press the PROGRAM button to select the washing program.

SPEEDY SOAK will not work in WOOL and ECONOMY, DELICATE Program.

Keep pressing the PROCESS button until the SPEEDY SOAK light is on and then Wash, Rinse, Spin lights are on simultaneously. Until the washing process is completed, the SPEEDY SOAK light is on.

Add the Detergent.

Add the laundry and press the START/PAUSE button.

Close the lid.

Finish

The appropriate quantity of Detergent marked next to the WATER LEVEL of WATER-DETERGENT.

The WATER LEVEL and the amount of Detergent to be used will be shown and water will be supplied.

Water will be supplied for 2 minutes after the start of the wash to supplement the absorbed water by the laundry.

When the wash program ends, the buzzer will ring for 10seconds before the Power goes off automatically.

AVORITE Wash

Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the normal cycle memory and then recall it for use at a later time.

Press the AUTO OFF (POWER) button to turn power on.

Select the FAVORITE program.

Select your FAVORITE wash conditions.

• Press the WATER TEMP. button to select wash Water

Temperature.

• Press the WATER LEVEL button to select WATER LEVEL.

• Press the OPTION to select OPTION.(Extra Rinse, Gentle Spin)

• Press the PROCESS button to select PROCESS(WASH, RINSE, SPIN) respectively you want to store.

Washing Programs

Press the START/PAUSE button to store & start your FAVORITE wash cycle. Power turns off automatically after wash.

Note

To recall your FAVORITE cycle.

1. Press POWER on.

2. Select the FAVORITE cycle by pressing the PROGRAM.

3. Press the START/PAUSE button. Then the wash cycle starts.

Washing Programs

ILENT Wash

Use this program to wash quietly in SILENT especially during late night and dawn.

Press the AUTO OFF (POWER) button to turn power on.

Press the PROGRAM button to select SILENT program.

Add the laundry into the washing tub.

Press the START/PAUSE button.

Add the Detergent and close the lid.

Note

• SILENT program takes longer washing time than FUZZY (Normal) program.

• To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has more moisture than normal.

UB CLEAN

If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer. Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub.

Press the POWER button to turn power on.

Press the PROGRAM button to select the TUB CLEAN program.

• Ex-Large WATER LEVEL is set automatically.

Press the START/PAUSE button.

• Left time is displayed.

After 10 minutes of water supplement. Add the oxygenated bleach (about 300m ).

• Do not use Detergent box.

• Do not place any laundry inside tub.

Additional Function Program

Close the lid.

Note

• Before using this program remove lint inside lint filter.

• When using this program, do not place any laundry inside tub.

• This program takes about 3 hours to be completed.

• After using this program, remove dirt inside filter.

• After finishing this program, open the lid of wash to remove irritant odor.

• Do not pour bleach into the tub directly. It might cause damage the tub.

• Do not leave diluted oxygenated bleach inside tub for long time. It rusts the tub must drain the remained diluted oxygenated water out.

• Use this program once for every month.

• Do not use this program repeatedly.

• When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid.

Additional Function Program

ELAY START (RESERVATION) Wash

DELAY START (RESERVATION) Wash is used to delay the finishing time of the operation. The hours to be delayed can be set by the user accordingly. The time on the display is the finishing time , not the start time.

Press the POWER button to turn power on.

Press the PROGRAM button to select the washing program.

Press the DELAY START (RESERVATION) button to set the time when the

delayed washing is to be completed.

How to set the delay time.

Example : It’s 7 a.m. now. If you’d like your wash to finish at 9

When you push the button the reservation time changes

p.m. set the time as in the figure below.

3 4 5 ...12 14 16 ... 48 3 repeatedly.

Select the program for laundry on the Control panel. This program will not work in WOOL and DELICATE Program.

(RES.=DELAY)

Add the Detergent.

Add the laundry and press the START/PAUSE button.

Close the lid.

Finish

Note

If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.

To select washing program, spinning time, WATER LEVEL or HOT/COLD manually, press the DELAY START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.

When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning program . (The laundry will be wrinkled if left for a long time after spinning.)

The appropriate quantity of Detergent marked next to the WATER LEVEL of WATER•DETERGENT. When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid

When you press the START/PAUSE button the light will blink.

Water will be supplied for 2 minutes after the start of the wash to supplement the water the laundry has absorbed.

The washing will be finished according to the delayed time.

ption

One or more OPTIONS (Extra Rinse, Gentle spin) can be selected for FUZZY and JEAN washing program. Wash program is changed as follows according to selected OPTIONS. “AIR DRY” can be selected, after turning on the power and “AIR DRY” times can be changed by pressing the “OPTION” button.

AIR DRY

Press the power button

Press the Option button untill above AIR DRY light is on.

Press the START/PAUSE button.

Closed the lid.

This cause is used to air dry of your laundry and tub dry

Turn Power on.

Additional Function Program

NOTE

■ Select "Air Dry" 30min ➔ Tub Dry

-Use this mode to keep inner tub from getting moldy caused by remaining moisture.

- Do not place any laundry inside tub.

- Use this mode once a week. Caution) For better performance, put drain hose down to the floor so that water inside will be completely drained out.

■ Select"Air Dry" above 1 hour

- Use this mode to reduce the drying time by minimizing remaining moisture on the laundry.

- In general, this is very effective on synthetic items(100% polyester).

- Do place laundry which is evenly distributed(Under 2kg).

- For normal clothes : Select 1 hour

- For synthetic items(100% polyester): Select 2 hours or 3 hours(on some models)

EXTRA RINSE

GENTLE SPIN

Gives additional one deep rinse eg.) If you want EXTRA RINSE, you must add fabric

softener manually when indication beep rings in the final rinse. This maximize the fabric softener function.

Gives GENTLE SPIN instead of normal spin.

+ 51 hidden pages