Please read this manual carefully before operating your set.
Retain it for future reference.
Record model name and serial number of the set.
Quote this information to your dealer when you require service.
P/No.:MFL62199107
4
afety Information
S
Read carefully and thoroughly through this booklet as it contains important safety information
that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
Introduction
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
WARNING
CAUTION
WATER
HEATER
SAFETY
PROPER
INSTALLATION
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
: Failure to comply with the instructions under this
sign may result in minor physical injuries or
damages to the product.
WARNING
• Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
CAUTION
• The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or
deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may
cause electric shock.
• Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
afety Information
S
5
Introduction
YOUR
LAUNDRY
AREA
WHEN USING
THE WASHER
WARNING
• Keep the area underneath and around your appliances free of combustible
materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger
explosion or fire.
• Close supervision is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine
while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
CAUTION
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors
may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving.
Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
6
afety Information
S
Introduction
WHEN USING
THE WASHER
WHEN NOT
IN USE
WARNING
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or
deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
CAUTION
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may
occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically
recommended in this Owner’s Manual, or in published user-repair instructions
that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a
cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire
due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any
part of the washing machine.
It will cause short circuit and electric shock.
dentification of Parts
I
Body
7
Introduction
POWDER AND LIQUID
DETERGENT BOX
LINT FILTER
Clean regularly to
stop linting on the
clothes load.
SOFTENER INLET
BLEACH
DISPENSER
FUNCTION
SELECTOR
TUB
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
ADJUSTABLE LEGS
Use to level the washing
machine for correct
balance & spin
operation.
Accessories
WATER SUPPLY
HOSE
Make sure the
water does not
leak.
POWER PLUG
If the supply cord is
damaged, it must be
replaced by the
manufacturer or its
service agents or
similarly qualified
person in order to
avoid a hazard.
DRAIN HOSE
for pump model
Check if the drain
hose is hung up
before operating the
washing machine.
DRAIN HOSE
for non pump
model
BASE
Water supply hoses
Drain hoseAnti-rat cover (option)
or
1 Each for COLD and
HOT water
NOTE
“ ” Part can be different according to the model.
or
8
unction Information
F
Our machine provides various washing methods which suits various conditions
and types of laundry.
Different types of laundry washing
FUZZY(Normal) Wash
Use this Program for everyday washing e.g. sheets, towels, T-shirts.
Introduction
Washing according to the condition of laundry
JEANS Wash
Use this Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)
EXTRA CLEANING
Use this program to get better rising performance.
WOOL Wash
Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
• Before washing your woolens check the care label for the washing instructions.
• When washing woolens use a mild Detergent recommended for washing wool.
• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.)
You may wish to handwash these articles and place them in the machine to spin dry.
FAVORITE Wash
This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)
SILENT Wash
Use this program to wash quietly at night. (refer to page 20)
(refer to page 16)
(refer to page 16)
QUICK WASH
QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)
SOAK Wash
SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and
grime. (refer to page 18)
Other washing method
TUB CLEAN
Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 21)
DELAY START Wash
DELAY START Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly. (refer to page 24)
OPTION WASH
When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,
SOAK/WASH/RINSE/SPIN. (refer to page 23)
reparation Before Washing
WIRE
P
Care Labels
* Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light)
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue in pockets.
Pretreatment on stains or heavy soil
• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page13)
Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in the
washer tub. To add items after washer has started, press Start button and
submerge additional items. Close the lid and press Start button again to restart.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent
tangling during washing.
Nylon net is not supplied by LG.
Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Separate clothes according to the type and amount of soil.
WARNING
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
Fire Hazard
9
BeforeStarting to Wash
pecial Guidefor Stain Removal
S
WARNING
■
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
■
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled containers and out of children’s reach.
• Thoroughly wash any utensil used.
• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or explosive substances because they give off vapors that could ignite or explode.
• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from
granular Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
Chocolate
Collar or cuff soil, cosmetics
Dye transfer on white fabric
Grass
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
Nail polish
Paint, varnish
Rust, brown or yellow
discoloration
Shoe polish
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.
TREATMENT
Follow fabric care label
instructions
13
BeforeStarting to Wash
16
ashing Programs
W
Washing
Programs
Washing Program s
(Normal Wash)
Used for normal loads, this
POWER
AUTO O FF
1
mode automatically selects the
most appropriate conditions
and completes the sequence
in one operation. The built-in
sensor detects the size of the
load and the ideal wash
power and wash, rinse and
spin times are set accordingly.
Use this program for washing
delicate fabrics such as lingerie
and woolens. (wash only “water
washable” clothes)
Before washing your woolens
check the care label for the
washing instructions.
(wash only water washable
clothes)
Use this mode when washing
lightly soiled clothes for a short
time. The highly recommended
laundry amount is under 2.0kg.
1
1
Add
the
laundry
2
3
3
2
• Select the
WOOL
program on
the Control
panel.
2
•
Select the
QUICK
WASH
program on
the Control
panel.
Add
the Detergent
4
•
Add the appropriate
quantity of Detergent as
indicated by the WATER
LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer’s
instructions
5
• Use neutral
Detergent
appropriate for the
laundry.
• When washing
woolens use a mild
Detergent
recommend- ed for
washing wool.
5
•
Add the appropriate
quantity of Detergent as
indicated by the
WATER LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer’s
instructions
Use Jean program when
washing Jeans of different sizes
Use this program to increase
rising performance.
This would include underwear
and baby clothes.
If someone has sensitive skin or
skin trouble,use this program.
1
1
3
• Spread
the jean
evenly in
the tub
3
2
•
Select the
JEANS
program on
the Control
panel.
2
• Select the
EXTRA
CLEANING
program on
Control
the
panel.
5
5
Close the lidFinishCaution & Note
STSTARART
PAUSE
USE
POWER
17
Washing Programs
3
• The pulsator rotates for
8 seconds to detect the
laundry load.
• Then the WATER LEVEL
and the amount of
Detergent to be used
will be shown and
water will be supplied.
4
4
5
• Water will be
supplied for 2
minutes after the
start of the wash to
supplement the
water the laundry
has absorbed.
6
6
6
• When the wash
program ends, the
buzzer will ring
for 10 seconds
before the Power
goes off
automatically.
7
7
• If water is already in the tub, or putting
wet laundry into the tub before starting
will increase the WATER LEVEL.
• With lightweight bulky loads, WATER
LEVEL can be set low.
• Changes to Water Temperature
(HOT/COLD) and wash level are
possible during operation.
(refer to page 14)
• When setting the WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
• Washing with HOT water may damage
the laundry (Water is set to cold
automatically). Ensure that the load is
under 2kg.
• In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing
may still contain some water. This is
normal.
• When static pressure of water is more
than 2kg/cm
will be within 19min.
2
, the QUICK WASH course
4
4
6
6
7
7
AVORITE Wash
POWERWER
AUTO OFF
START
PAUSE
USE
POWER
POWER
F
Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the
normal cycle memory and then recall it for use at a later time.
1
Press the POWER (AUTO OFF) button to turn power on.
2
Select the FAVORITE program.
Select your FAVORITE wash conditions.
3
• Press the TEMP. button to select wash Water
Temperature.
• Press the WATER button to select
WATER.
• Press the WASH button, the RINSE button & the SPIN
button to select wash time, rinse time & spin time
respectively you want to store.
19
Washing Programs
4
Press the START/PAUSE button to store & start your FAVORITE wash cycle.
Power turns off automatically after wash.
NOTE
To recall your FAVORITE cycle.
1. Press POWER on.
2. Select the FAVORITE cycle by pressing the PROGRAM.
3. Press the START/PAUSE button. Then the wash cycle starts.
20
POWERWER
AUTO OFF
POWER
STSTARART
PAUSE
USE
POWER
Washing Programs
ILENT Wash
S
Use this program to wash quietly in SILENT especially during late night and dawn.
1
Press the POWER (AUTO OFF) button to turn power on.
2
Press the PROGRAM button to select SILENT program.
3
Add the laundry into the washing tub.
4
Press the START/PAUSE button.
5
Add the Detergent and close the lid.
NOTE
• SILENT program takes longer washing time than FUZZY(Normal) program.
• To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has
more moisture than normal.
21
START
PAUSE
USE
POWER
POWERWER
AUTO OFF
POWER
UB CLEAN
T
If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in
your washer.
Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact
with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these
case, use this program to clean inner tub and outer tub.
1
Press the POWER (AUTO OFF) button to turn power on.
2
Press the PROGRAM button to select the TUB CLEAN program.
Ex-Large WATER is set automatically.
3
Press the START/PAUSE button.
4
After 10 minutes of water supplement. Add the oxygenated bleach (about 300m ).
• Do not use Detergent box.
• Do not place any laundry inside tub.
• Left time is displayed.
Additional Function Program
5
Close the lid.
NOTE
• Before using this program remove lint inside lint filter.
• When using this program, do not place any laundry inside tub.
• This program takes about 3 hours to be completed.
• After using this program, remove dirt inside filter.
• After finishing this program, open the lid of wash to remove irritant odor.
• Do not pour bleach into the tub directly. It might cause damage the tub.
• Do not leave diluted oxygenated bleach inside tub for long time.
It rusts the tub must drain the remained diluted oxygenated water out.
• Use this program once for every month.
• Do not use this program repeatedly.
• When the lid is open the machine will not operate, and an
alarm signal will remind you to close the lid.
22
PO
WER
STSTARART
PAUSE
USE
POWER
IR DRY
A
AIR DRY for your laundary.
1
Press the POWER (AUTO OFF) button to turn power on.
WER
AUTO OFF
Additional Function Program
2
Press the AIR DRY button to select the desired timing.
3
Press the START/PAUSE button.
4
Closed the lid.
NOTE
■ Select "Air Dry" 30min ➔ TUB DRY
-Use this mode to keep inner tub from getting moldy caused by remaining moisture.
- Do not place any laundry inside tub.
- Use this mode once a week.
Caution) For better performance, put drain hose down to the floor so that water inside will be
completely drained out.
■ Select “Air Dry” above 1 hour
- Use this mode to reduce the drying time by minimizing remaining moisture on the laundry.
- In general, this is very effective on synthetic items(100% polyester).
- Do place laundry which is evenly distributed(Under 2kg).
- For normal clothes : Select 1 hour
- For synthetic items(100% polyester): Select 2 hours or 3 hours(on some models)
23
START
PAUSE
USE
POWER
POWERWER
AUTO OFF
ption Washing
O
When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.
1
Press the POWER (AUTO OFF) button to turn power on.
2
Only Wash
Press the
select the desired timing.
Press the
select the desired timing.
Press the
select the desired times of
rinse.
WASH
Only Wash,Rinse
WA S H
RINSE
button to
button to
button to
Only Rinse
Press the
select the desired times of
rinse.
Press the
select the desired times of
rinse.
Press the
select the desired times of
spin.
RINSE
button to
Only Rinse,Spin
RINSE
button to
SPIN
button to
Only Spin
Press the
select the desired times of
spin.
When you want to only
drain, wait until the water
in the washing tub drains
completely.
SPIN
button to
Only Drain
Additional Function Program
You can use this option
for preventing wrinkles of
laundry
Press the WATER button, to control the water level according to the amount
3
of laundry. If you do not choose anything, it is set the middle water level
automatically.
4
Add the laundry into the washing tub.
5
Press the START/PAUSE button.
6
Add the detergent and close the lid.
NOTE
• When a Wash, Wash/Rinse or Rinse only option is selected, after the wash is completed the water will not
be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained
completely. Then press the START/PAUSE button.
• If you do not specify the water level, then Medium will be automatically selected.
• If only Rinse is selected, the process will start from Water Supply.
Loading...
+ 53 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.