LG WFS1259ET Owner's Manual

OWNER’S MANUAL

WASHING MACHINE

Please read this manual carefully before operating your washing machine and retain it for future reference.

WFS1259ET

*MFL68781009*

Rev :01 (09T15)

www.lg.com

roduct Features

Washer doesn’t operate while the lid is open. If the lid is open during the wash, rinse or spin cycles, the operation stops for safety.

FUZZY logic control

• A built-in load sensor automatically detects the laundry load and a microprocessor optimizes washing conditions such as ideal Water level and washing time.

SENSING

START

• Advanced technology is built into the Electronic Control System which ensures the best washing result.

Laundry Sensor

Water Level Sensor

SETTING

Optimum Washing Condition

WASHING

AUTO

POWER

OFF

Turbo drum washing (option)

• When “Punch + 3” washing wings turn, the washing tub turns in the opposite direction. This makes the both sides current of water which improve wash-performance by rubbing clothes strongly.

3 Step washing

• 3 step washing makes the best washing performance with low tangling.

Rubbing Rubbing and

Shaking

Shaking and Disentangling

NOTE

Be sure to remove the unit from the carton base, otherwise the machine will not be able to operate properly.

ontents

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.

Introduction Safety Information 4

Identification of Parts 7 Function Information 8

Before Starting to Wash Preparation Before Washing 9

Use of Water, Dispenser Drawer, Detergent and Softener Special Guide for Stain Removal 13 Function of each Button 14

Washing Course Normal Wash 16

Wool Wash 16 Quick wash 16 Duvet Wash 16 Extra Clean 16 Silent Wash 18 Pre Wash + Normal Wash 18 Soak Wash 20

Additional Function Program Tub Clean 21

Air Dry 22 Option Washing 23 Delay Start (Reservation) Wash 24 Other Useful Functions 25

Installation Placing and Leveling 26

Connecting Water Supply Hose 27 Connecting Drain Hose 30

Care and Maintenance Grounding Method 31

Cleaning and Maintenance 32

Troubleshooting Soft Safety Door 34

Common washing problems 35 Troubleshooting 36

Smart Diagnosis Blanket Folding Method 38

Specification Specification 39

afety Information

This booklet is divided into 2 parts : Warning and Caution.

Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.

: This is a warning sign specifying user’s applications which might

be dangerous.

Introduction

WATER HEATER SAFETY

PROPER INSTALLATION

: This is a sign specifying ‘Strictly Forbidden’ applications.

WARNING : Failure to comply with the instructions under this sign may

result in major physical injuries or death.

CAUTION : Failure to comply with the instructions under this sign may

result in minor physical injuries or damages to the product.

WARNING

• Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances. If the Hot water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the Hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

CAUTION

•

The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.

If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur

• Properly ground washer to conform with all governing codes and ordinances. Follow details in Installation Instructions

If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock

• Must be positioned so that the plug is accessible.

If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.

• Make sure the plug is completely pushed into the outlet.

Failure to do so may cause electric shock and fire due to overheating.

afety Information

YOUR LAUNDRY AREA

WHEN USING THE WASHER

WARNING

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.

Operating with such materials around the machine may trigger explosion or fire.

• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.

There is potential danger that children might drown in the tub.

Do not touch the power plug with a wet hand.

It will cause electric shock

Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.

There is a rotating mechanism under the machine, so you could be injured.

CAUTION

•

Use this appliance only for its intended purpose as described in this Owner’s Manual.

•

The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by

removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning

NOTE

Pressing Power button to turn off does NOT disconnect the appliance from the power supply.

Introduction

• Make sure that drainage is working properly If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.

• If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving. Wait until the machine has completely stopped before opening the lid.

Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

Operating with a damaged plug may cause electric shock.

Do not use water hotter than 50°C.

Use of excessively hot water may cause damage to fabrics or cause leakage of water.

afety Information

WHEN USING THE WASHING

Introduction

WHEN NOT IN USE

WARNING

Do not use a plug socket and wiring equipment for more than their rated capacity.

Exceeding the limit may lead to electric shock, fire , break down, and/ or deformation of parts.

Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce toxic gases which may cause death.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents, kerosene, etc). Do not add these substances to the wash water.

Do not use or place these substances around your washer or dryer during operation.

It may ignite or explode.

CAUTION

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5 years.

• When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.

• Wipe off dirt or dust on the contacts of the power plug.

Using unclean power plug may cause fire.

• Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.

Children may be trapped and suffocated if the lid is left intact.

Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.

Operating the machine with improperly replaced parts may be a cause for fire or electric shock.

Do not tamper with controls.

It may lead to electric shock, fire , break down, deformation.

Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.

Failure to observe these instructions may cause electric shock or fire due to short-circuit.

When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.

It will cause short circuit and electric shock.

dentification Part

Body

* Picture might be different by model.

SOFT SAFETY DOOR TEMPERED GLASS

POWDER AND LIQUID DETERGENT BOX

SOFTENER INLET BLEACH DISPENSER

FUNCTION SELECTOR

TUB START/PAUSE

BUTTON

Use to start or stop the washing machine temporarily

Introduction

*WATER SUPPLY HOSE

Make sure the water does not leak.

*POWER PLUG

If the supply cord is damage, it must be replaced by the manufacture or its service agents or similar qualified person in order to avoid a hazard.

LINT FILTER

Clean regularly to stop linting on the clothes load.

*DRAIN HOSE

for pump model Check if the drain hose is hung up before operating the washing machine.

ADJUSTABLE LEGS

Use to level the washing machine for correct balance & spin operation

Accessories

Water supply hoses Drain hose

For None-Pump model

For Pump model

1 Each for Cold and

Hot water

NOTE

“*” Part can be different according to the model.

*DRAIN HOSE

for non pump model

BASE

Anti-rat cover (option)

unction Information

Our machine provides various washing methods which suits various conditions and types of laundry.

Different types of laundry washing

Normal Wash

Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)

Duvet Wash

Use for blanket or Duvet with (Hand Wash) sign. (refer to page 16)

Extra Clean

Introduction

Use this Course to get better rising performance. (refer to page 16)

Wool Wash

Wool clothes (lingerie, wool, etc.) Which may be easily damaged can be washed. (refer to page 16) The fibers of machine washable woolens have been specifically modified to prevent felting when they

are machine washed. Most hand knitted garments are not made of machine washable wool and we recommend that you

hand wash them

• Before washing your woolens check the care label for the washing instructions.

• When washing woolens use a mild Detergent recommended for washing wool.

• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.

• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)

Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.

(Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to hand wash these articles and place them in the machine to spin dry.

Pre Wash+

Normal

Washing laundry with cycle that pretreats immediate stain without hand-wash. i.e. Necessary for clothes which could be smelled badly without prompt laundry. (refer to page 18)

Silent Wash

Use this program to wash quietly at night. (refer to page 18)

Washing according to the condition of laundry

Quick Wash

Quick Wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time.(refer to page 16)

Soak Wash

Soak Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 20)

Other washing method

Tub Clean

Use this program to clean the inside of washing machine especially Inner tub & Outer tub (refer to page 21)

Delay Start Wash

Delay Start Wash is used to delay the finishing time of the operation. The number of hours to be delayed can be set by the user accordingly. (refer to page 24)

Option Wash

When the user needs only Spin, Rinse/Spin, Rinse, Wash/Rinse, Wash, Wash/Rinse/Spin, Soak/Wash/ Rinse/Spin. (refer to page 23)

reparation Before Washing

Care Labels

* Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

Sorting

To get the best results, different fabrics need to be washed in different ways.

• SOIL

(Heavy, Normal, Light)

• COLOR

(Whites, Lights, Darks)

• LINT

(Lint producers, Collectors)

Separate clothes according to the type and amount of soil.

Separate white fabrics from colored fabrics.

Separate lint producers and lint collectors. Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers Lint Collectors Synthetics, Corduroy, Permanent Press, Socks.

Check before Loading

• Check all pockets to make sure that they are empty. Things such as nails, hair clips, matches, pens,

coins, and keys can damage both your washer and your clothes.

•

Mend any torn garments or loose buttons. Tears or holes may become larger during washing.

• Remove belts, under wires, etc. to prevent damage to the machine or your clothes.

• Pretreat any dirt and stains.

• Make sure the clothes are washable in water.

• Check the washing instructions.

WIRE

• Remove tissue in pockets.

Caution

Do not wash or spin any item labeled or known to be water-proof or water-resistant, even if the product care label on the item permits machine washing. Failure to follow these instructions could

result in severe damage to your laundry, your washer and/or property damage as a result of abnormal vibration of the washer.

- Examples of water-proof or water-resistant items include certain mattress pads, mattress covers, rain gear, camping gear, skiing apparel , outdoor gear and similar items.

Pretreatment on stains or heavy soil

• Use ‘PreWash+Normal’ cycle for very soiled clothes. In case of heavily soiled clothes, pretreatment

may require before the cycle.

• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the

washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

• Use a pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are left the

harder they are to remove. (For more detail refer to page 13)

Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).

Load Size

The Water Level should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.

Light and Large-sized clothing

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Long laundry items

Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items don’t snag on other clothes.

Nylon net is not supplied by LG.

Never place items in the washer that are dampened with gasoline or other flammable fluids.

No washer can completely remove oil. Do not dry anything that has ever had any

type of oil on it (including cooking oils). Doing so can result in death, explosion,

or fire.

WARNING

Fire Hazard

Before Starting to Wash

Using Water

Before Starting to Wash

se of Water, Dispenser Drawer , Detergent and Softener

Amount of Water Level

• This machine detects quantity of laundry automatically, then sets the Water Level and proper amount of detergent.

• When you select a wash Course, the Water level and amount of detergent (to be used) will be shown on the panel.

• The following table shows the amount of water.

• When the water level is automatically detected, it may differ depending on the quantity of laundry even though the same water level is indicated on the control panel.

NOTE

[Minimum water amount]

It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to some height. That’s because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.

Water Temperature (WARM,COLD : Option for Only 2 Vale)

• The machine sets the appropriate temperature automatically according to the wash course.

• You can change the water temperature by pressing the Water Temp. Button. (refer to page 14)

• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results. We recommend temperatures of:

- HOT 49~60 °C …(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items.

- WARM 29~40 °C …(85-105˚F) Most items

- COLD *18~40 °C …(65-75˚F) Only very bright colors with light soil.

• When washing in Cold water additional steps may be needed:

- Adjust Detergent amount and pre-dissolve Detergent in Warm water

- Pretreat spots and stains

- Soak heavily soiled items

- Use appropriate bleach

* Temperature below 18 °C … (65 ˚F) will not activate laundry additives and may cause lint, residue,

poor cleaning, etc. In addition, Detergent manufactures and care labels define Cold water as 26~29 °

C… (80-85 ˚F). If the temperature of the water in the tub is too cold for your hands, the Detergent will

not activate and clean effectively.

Attention

If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron

filter may be necessary for severe cases.

Using detergent

Detergent

Follow the detergent package directions. Using too little etergent is a common cause of laundry problems. Use more detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.

Choosing the right Detergent

We recommend the use of domestic detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to use

detergent suitable for washing woolens.

Rev :01 (09T15)

How much Detergent

When you select a wash Course the water level and the amount of detergent (to be used) will be shown on the control panel. The amount of a cup in the diagram is about 40 g for concentrated detergent. The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work cloches may need more Detergent, while bath towels usually need less.). For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.

Note: To check you are using the correct amount of detergent, lift the lid of your machine about half-way through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough detergent had been used; soil and lint can settle back on the clothes or the washing machine. If excess detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, so use it accordingly.

Adding the Detergent

Open the detergent dispenser and deposit the appropriate amount

Powder Detergent Box

of detergent where you deposit the detergent Powder Detergent dispenser. Some detergents MUST be fully dissolved before adding to your machine to get the best wash results.

where you deposit the detergent

Check the instructions on the detergent packet. If you use powdered detergent if is essential that the required amount be fully dissolved in very hot water before being added to warm or hot water for the actual wash. Pre-dissolving detergent in warm water when washing in cold water can improve its performance.

Using Liquid Bleach

• Check clothing care label for special instructions and separate the laundry

Bleach Dispenser

to be bleached

• Dilute liquid chlorine bleach.

• Measure the recommended amount of liquid bleach carefully following instructions on the bottle.

• Before starting the washer, pour measured amount of bleach directly into bleach dispenser. Avoid splashing or overfilling. Powdered bleach should be mixed with water before pouring.

NOTE

• Never pour undiluted liquid bleach directly onto clothes or into the wash basket.

This may cause change of color or damage the laundry.

• Do not pour powdered bleach into bleach dispenser.

Before Starting to Wash

se of Water, Dispenser Drawer, Detergent and Softener

Use Fabric Softener

• Dilute fabric softener with water. Undiluted fabric softener may result in spots that look like oil stain

• Measure and add the recommended amount of fabric softener into the compartment marked with this symbol( ). Follow manufacturer's direction

)

Fabric softener is automatically dispensed in the final rinse with

indication beep.

) If you want extra rinse , you must add fabric softener manually when indication beep rings in the final

rinse. This maximize the fabric softener function.

Before Starting to Wash

• Do not overfill. The dispenser hold max 35 mL. Never add more than 35 mL. Overfilling can cause early dispensing of the fabric softener which could result in stained clothes. A cup with a pouring spout will help you avoid spilling

• The effect of adding fabric softener may vary according to its viscosity, The sticker fabric softener makes its effect the lower. For a sticky softener it is recommended that it be diluted with water, then be manually put during the time when the washer beeps several times before the final rinse. This function informing correct time dispense manually is optionally applied to some models. Please keep it in mind that fabric softener has to be diluted with water before dispensed and never poured directly on clothes.

Attention

• Do not mix with Detergent or bleach.

• Never pour fabric softener directly on clothes. It may stain them.

• Do not stop the washer during the first spin for timely dispensing.

• Option washing is not designed to be used with fabric softener dispenser.

Scrud (Waxy Build up)

Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.

If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.

Softener dispenser ( )

If you wish to use fabric softener we recommend

• Using fabric softener sparingly.

• When filling the dispenser, do not splash or overfill.

• Clean dispenser as soon as the cycle is finished.

• Clean your machine regularly. (refer to page 21 or 32)

• Cold water washing increases the chance of this build-up occurring. We recommend a regular Warm or Hot wash e.g. every 5th wash should be at least a warm one.

• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.

Rev :01 (09T15)

pecial Guide for Stain Removal

WARNING

■ Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.

■ To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:

• Read and comply with all instructions on stain removal products.

• Keep stain removal products in their original labeled containers and out of children’s reach

• Thoroughly wash any utensil used.

• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.

• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.

• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.

For successful stain removal :

• Remove stains promptly.

• Use ‘Pre Wash+Normal’ cycle for very soiled clothes. In case of heavily soiled clothes, pretreatment may require before the cycle.

• Determine the kind of stain, then follow the recommended treatment in the stain removal chart below.

• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.

• Use COLD water on unknown stains because HOT water can set stains.

Follow fabric care label instructions

• Check care label instructions for treatments to avoid on specific fabrics.

• Check for colorfastness by testing stain remover on an inside seam.

• Rinse and wash items after stain removal.

Stain Removal

Adhesive tape, chewing gum, rubber

STAIN TREATMENT

cement Baby formula, dairy products, egg Beverages (coffee, tea, soda, juice,

alcoholic beverages) Blood

Candle wax, crayon

Chocolate Collar or cuff soil, cosmetics Dye transfer on white fabric Grass

Grease, oil, tar (butter, fats, salad dressing, cooking oils, car grease, motor oils)

Ink

Mildew, scorch Mud

Mustard, tomato Nail polish

Paint, varnish

Rust, brown or yellow discoloration

Shoe polish

Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonflammable dry cleaning fluid.

Use product containing enzymes to pretreat or soak stains. Pretreat stain. Wash using COLD water and bleach safe for fabric.

Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using bleach safe for fabric. Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Pretreat with prewash stain remover or rub with bar soap. Use packaged color remover. Wash using bleach safe for fabric. Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply

nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash using hottest water safe for fabric. Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or nonflammable dry cleaning fluid.

Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly mildewed fabrics may be permanently damaged.

Brush off dry mud. Pretreat or soak with product containing enzymes. Pretreat with prewash stain remover. Wash using bleach safe for fabric. May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of

stain. Repeat, replacing paper towels frequently. Do not use on acetate fabrics. WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,

OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing. For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and

Do not use chlorine bleach because it may intensify discoloration.

LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach safe for fabric.

Before Starting to Wash

Rev :01 (09T15)

unction of each Button

Water Temperature Button

• Use to select Water Temperature. Pressing the button allows you to select COLD ▶ WARM(HOT&COLD) ▶ HOT ▶ COLD respectivly. Default setting is COLD.

Before Starting to Wash

Soil Level Button

• This button allows you to select the strength of the wash action

•

Power option selections light up in sequence as follows Normal ▶ Heavy ▶ Light ▶ Normal as the button is pushed. This can be selectted for any course.

•

Adjutment can be made while washing

(only 2 valve)

Water Level Button

• Use to select the proper amount of water in relation to the weight and type of laundry.

• Automatically controlled, but can be selected manually by pressing the Water Level Button.

• Water is automatically selected for Normal Course.

The following settings are indicated as the button is pushed 7 ▶ 8 ▶ 9 ▶10 ▶1 ▶ 2 ▶ 3 ▶ 4 ▶5 ▶ 6 ▶7

Air Dry

•

This button is used for airdrying of your laundry.

• Air dry selections light up in sequence as follows

30 ▶ 60 ▶ 90 ▶ 120

•

If you want to use Air Dry, Press & hold 3 sec. Spin key.

NOTE

* Even if the water level or the water temperature are changed by the user in Normal Course, the sensor will still

work. The sensor algorithm may differ according to models.

* The control panel may differ according to different models.

Child Lock Function

•

Use to lock or unlock the control buttons to prevent settings from being changed by a child. To lock, push the Rinse buttons and to unlock push them one more time during the washing process.

(refer to page 25)

Wash. Rinse. Spin Button

•

Use when wash, rinse, spin time need to be adjusted.

•

The time increases when the button is pressed.

•

If adjustments are needed during the wash, press the [start/ pause] button before making any changes.

•

When the button is pressed during washing, the remaining time is displayed.

Display laundry progress

•

Laundry progress is indicated here.

•

Process to be done will have light on. Process in progress will blink and process already done will have light off

Display remaining time, reservation time,

and alarm for trouble

•

During operation this indicates time to finish of laundry.

Ex.) Indicates remaining time of laundry, rinse, spin dry during operation/pause.

• If there is a trouble, it blinks with buzzer sound and indicates the source of trouble. It will work normally after troubleshooting.

POWER Button

• User to turn the power on or off.

• Push again and power goes on or off

•

The power goes off automatically about 10 seconds after the wash is finisher.

Before Starting to Wash

Delay Start (Reservation) Button

•

Use to set a delayed finishing time.

•

The time increases when the button is pushed.

•

The following settings are indicated as the button is pushed 3 ▶ 4

▶ 5 ▶ ... 11 ▶ 12 ▶ 14 ▶ 16 ▶ 18 ▶ OFF ▶ 3 HOUR.

•

To cancel delay time, turn the power switch off.

(refer to page 24)

Course Button

• Use for selecting Wash Course.

• This button allows you to select 8 different Course for different kinds of laundry and dirtiness.

•

Course selections light up in sequence as follows

Course 1 : Normal ▶ Wool ▶ Duvet ▶ Silent Course 2 : Pre Wash + Normal ▶ Quick Wash

▶ Extra Clean ▶ Tub Clean Select the desired Course by pressing the

button.

START/PAUSE

Button

•

Use to start or pause the washing process.

• Repeats start and pause by pushing the button.

ashing Course

Washing Course

Used for normal loads, this mode automatically selects the most appropriate conditions and completes the sequence in one operation. The built-in

Washing Course

sensor detects the size of the load and the ideal wash power and wash, rinse and spin times

are set accordingly.

Use this program for washing delicate fabrics such as lingerie and woolens. (wash only “water washable” clothes) Before washing your woolens check the care label for the washing instructions. (wash

only water washable clothes)

Use this mode when washing lightly soiled clothes for a short time. The highly recommended laundry amount is under 2.0 kg.

Add the

laundry

•

Select the Wool program on the Control panel.

•

Select the Quick Wash Course on the Control panel.

Add the detergent Close the lid Finish Caution & Note

•

Add the appropriate quantity of Detergent as indicated by the WATER LEVEL next to Water Detergent. Or follow

the Detergent manufacturer’s instructions

•

Use neutral Detergent appropriate for the laundry.

•

When washing woolens use a mild Detergent recommended

for washing wool.

•

Add the appropriate quantity of Detergents as indicated by the Water Level next to Water Detergent. Or follow the Detergent manufacturer’s instructions

Use Duvet Course when washing Jeans of different sizes

Use this Course to increase rising performance. This would include underwear and baby clothes. If someone has sensitive skin or skin trouble, use this Course.

•

Spread the jeans evenly in the tub.

•

Select the Duvet course on the Control panel.

•

Select the Extra Clean Course on the Control panel.

• The pulsate rotates for 8 seconds to detect the

laundry load,

•

Then the Waster Level and the amount of Detergent to be used will be shown

and water will be supplied.

•

Water will be supplied for 2 minutes after the start of the wash to supplement the water the laundry has absorbed.

•

When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.

• If water is already in the tub, or putting wet laundry into the

tub before starting will increase the Water Level.

• With lightweight bulky loads, Water Level can be set low.

•

Changes to Water Temperature (Hot/Cold) and wash level are possible during operation. (refer

to page 14)

•

When setting the Water Level manually, do not set to Medium to prevent damage to laundry.

•

Washing with Hot water may damage the laundry (Water is set to cold automatically). Ensure that the load is under 2 kg.

• In order to avoid damage to laundry, the spin cycle may appear slow. This also avoids wrinkles and clothing may still contain some water.This is normal

•

When static pressure of water is more than 2 kgf./cm².

Load

Recommend

Washing Course

Less than 12 kg.

Less than 2 kg.

Less than 12 kg.

ashing Course

Washing Course

Use this Course to quietly in Silent especically during late night and dawn.

Washing Course

Washing laundry with cycle that pre treats immediate stain without Hand - wash could be smelled badly without prompt laundry

Add the laundry

•

Select the Silent Course on the Control panel.

•

Select the Course on the Control Panel.

Add the detergent Close the lid Finish Caution & Note

•

Add the appropriate quantity of Detergents as indicated by the Water Level next to Water Detergent. Or follow the Detergent manufacturer’s instructions

•

Add the appropriate quantity of Detergent as indicated by the Water Level. Or follow the Detergent manufacturer’s instructions

•

Silent course take longer washing time than Normal program

• To reduce noise in spining, spin rmp is lower than normal spining rpm. So the laundry has more moisture than normal.

Load

Recommend

Less than 12 kg.

Washing Course

oak Wash

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty. soak mode can be used with Normal , Duvet , Silent , Extra Clean Course

Press the POWER button to turn power on.

Press the Course button to select the washing course

•

Soak will not work in Wool and Quick wash, Pre Wash + Normal Tub Clean Course

Press the Wash button, to select Soak course.

•

Press the Wash button until the light turns on ‘Soak’ and ‘Wash’ simultaneously as next image.

Add the Detergent

•

The appropriate quantity of Detergent marked next to the Water Level

Add the laundry and press the START/PAUSE button

• The Water Level will be shown and water will be supplied.

Close the lid.

•

Water will be supplied for 2 minutes after the start of the wash to supplement the absorbed water by the laundry.

Finish •

When the wash Course ends, the buzzer will ring for 10 seconds before the Power goes off automatically

ub Clean

If scrub is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer. Scrub is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this Course to clean inner tub and outer tub.

Press the POWER button to turn power on.

Press the Course button to select the Tub Clean Course.

 Ex-Large Water is set automatically.

Press the START/PAUSE button.

• Left time is displayed.

After 10 minutes of water supplement. Add the oxygenated bleach (about 300 ml).

• Do not use the Detergent box.

• Do not place any laundry inside tub.

Additional Function Course

Close the lid.

• When the lid is open the machine will not operate, and chime sound will remind you to close the lid.

NOTE

• Before using this Course remove lint inside lint filter.

• When using this Course, do not place any laundry inside tub.

• After using this Course, remove dirt inside filter.

• After finishing this Course, open the lid of wash to remove irritant odor.

• Do not pour bleach into the tub directly. It might cause damage the tub.

• Do not leave diluted oxygenated bleach inside tub for long time.

• It rusts the tub must drain the remained diluted oxygenated water out.

• Use this Course once for every month.

• Do not use this Course repeatedly.

Additional Function Course

ir Dry

Air Dry for your laundry.

Press the POWER button to turn power on.

Press the Air Dry button to select the desired timing.

Press Spin for 3 seconds to select Air Dry

• Other function cannot be selected during Air Dry.

• Automatically set to 30 minutes upon selection.

• Press Spin button again to select duration (30 min. ▶ 60 min. ▶ 90 min. ▶ 120 min.)

• To deselect Air Dry press power button.

Press the START/PAUSE button.

Close the lid.

NOTE

• Select “Air Dry” 30 min.

- Use this mode to keep inner tub from getting moldy caused by remaining moisture.

- Do not place any laundry inside tub.

- Use this mode once a week.

Caution) For better performance, put drain hose down to the floor so that water inside will be completely drained out.

• Select “Air Dry” above 1 hour

- Use this mode to reduce the drying time by minimizing remaining moisture on the laundry.

- In general, this is very effective on synthetic items(100% polyester).

- Do place laundry which is evenly distributed(Under 2 kg.).

- For normal clothes : Select 1 hour.

- For synthetic items (100% polyester): Select 2 hours or 3 hours(on some models)

ption Washing

When you only need the Wash , Wash/Rinse or Rinse cycles , these can be set manually.

Press the POWER button to turn power on.

Additional Function Course

Press the button, select the desired timing of wash.

Only Wash Only Rinse Only Spin

1)Select Lamps On

2)select Lamps Off

3)Select Lamps Off

Press the buttons, select the desired times of rinse.

Lamps Off

1)select Lamps On

2)Select Lamps Off

Press the button Spin to select the desired times of Spin.

Lamps Off

1)Select Lamps On

Only Wash,Rinse Only Rinse,Spin Only Drain

Press the button to select the desired timing of wash, rinse.

Press the button , select the desired timing of rinse, spin.

When you want to only drain, wait until the water in the washing tub

drains completely.

1)Select Lamps On

Press the Water Level button, to control the water level according to the amount of laundry. If you

do not choose anything, it is set the middle water level automatically.

Add the laundry into the washing tub.

Press the START/PAUSE button.

2)select Lamps On

3)Select Lamps Off

Lamps Off

1)select Lamps On

2)Select Lamps On

Add the detergent and close the lid.

NOTE

• When a Wash or Rinse only option is selected, after the wash is completed the water will not be

drained off. If you wish to drain the water, press SPIN button and wait until water in the tub has drained completely. Then press the START/PAUSE button.

• If you do not specify the water level, then Medium will be automatically selected.

• If only Rinse is selected, the process will start from Water Supply.

Additional Function Course

elay Start (Reservation) Wash

Delay Start (Reservation) Wash is used to delay the finishing time of the operation. The hours to be delayed can be set by the user accordingly. The time on the display is the finishing time, not the start time.

Press the POWER button to turn power on.

Press the Course button to select the washing course.

•

Select the Course for laundry on the Control panel. This Course will not work in Wool and Tub Clean Course

Press the Delay (Reservation) button.

• The light will ‘Delay’ turn on and ‘Time Left’ will be marked.

• Press the button repeatedly to set the desired finishing time. For example, To finish washing in 9 hours from now, By make

the number 9:00 pressing the Delay button repeatedly.

(RES. = Delay) ➨

Add the Detergent.

•

The appropriate quantity of Detergent marked next to the

Water of Water• Detergent.

•

When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid.

Add the laundry and press the START/PAUSE button.

• When you press the START/PAUSE button the light will blink.

Close the lid.

• Water will then be let in again 2 minutes after the start of the to supplement the water the laundry has absorbed.

Finish • The washing will be finished according to the delayed time.

NOTE

• Finishing time can be delayed from 3 ∼ 18 hours. Delaying 3 ∼ 12 hours can be done in 1 hour time intervals and from 12 ∼ 18 hours in 2 hour time intervals.

• If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.

• To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the Delay Start (Reservation) button and select the desired option. Then press the START/PAUSE button.

• When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning program. (The laundry will be wrinkled if left for a long time after spinning.)

+ 56 hidden pages