LG WFS1258ETD Owner's Manual [es]

WFS1258ETD

P/No. : MFL62880714

Product Features

The Turbo Drum DD washing machine does not operate with the lid open.

If the lid is opened during wash, rinse and spin cycles, the machine will stop automatically.

Please close the door gently. Closing the door in an agressive manner can cause damage and or injury.

sensors

The sensor automatically detects the quantity of Detergent put in by a user and the temperature and quality of the water to produce the best algorithm for washing and rinsing, to give the best washing results.

FUZZY logic control

A built-in load sensor automatically detects and measures the laundry load and a microprocessor optimizes washing conditions such as ideal water consumption and washing time.

Advanced technology is built into the Electronic Control System which ensures the best washing result.

START	SENSING	SETTING	WASHING	AUTO
	Laundry Sensor	Optimum		POWER
	Water Level Sensor	Washing		OFF
		Condition

Turbo Drum DD washing

Stains are removed by	Stains are removed by	With high speed
pulsator movement	the tub movement	spinning of the tub,
		stains are removed

Low Noise Direct Drive System

The advanced Brushless DC motor rotates the Tub directly without belt and clutch, thereby reducing the noise of the washer.

The washing machine adjusts to optimum speed according to the type of clothing in the load.

Contents

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.

Introduction

Before Starting to Wash

Washing Programs

Additional Function

Program

Installation

Care and Maintenance

Troubleshooting

Terms of Warranty

Specification

Safety Information	4
Identification of Parts	7
Function Information	8
Preparation Before Washing	9
Use of Water, Dispenser Drawer, Detergent and Softener	10
Special Guide for Stain Removal	13
Function of each Button	14
FUZZY Wash (Normal Wash)	16
WOOL Wash	16
QUICK WASH	16
JEANS Wash	16
SMART CLEANING	16
SOAK Wash	18
FAVORITE Wash	19
SILENT Wash	20
TUB CLEAN	21
AIR DRY	22
TUB DRY	22
Option Washing	23
DELAY START (RESERVATION) Wash	24
Other Useful Functions	25
Placing and Leveling	26
Connecting Water Supply Hose	27
Connecting Drain Hose	30
Grounding Method	31
Cleaning and Maintenance	32
Use of Handle Locker	34
Common washing problems	35
Troubleshooting	36
Terms of Warranty	37
Specification	38

4

<![if ! IE]>

<![endif]>Introduction

Safety Information

Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts : Warning and Caution.

:This is a warning sign specifying user’s applications which might be dangerous.

:This is a sign specifying ‘Strictly Forbidden’ applications.

WARNING : Failure to comply with the instructions under this sign may result in major physical injuries or death.

CAUTION: Failure to comply with the instructions under this

sign may result in minor physical injuries or damages to the product.

	WATER	WARNING
	HEATER
	SAFETY	• Under certain conditions hydrogen gas may be produced in a water heater that has not been
		used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
		If the HOT water has not been used for two weeks or more, prevent the possibility of
		damage or injury by turning on all Hot water faucets and allowing them to run for several
		minutes. Do this before using any electrical appliance which is connected to the HOT
		water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
		the gas is flammable, do not smoke or use an open flame or appliance during this process.
	PROPER	CAUTION
	INSTALLATION
		• The base opening must not be obstructed by carpeting when the washing machine is installed on a
		carpeted floor.
		• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
		If the product is exposed to such conditions, electric shock, fire, break down or
		deformation may occur.
		• Properly ground washer to conform with all governing codes and ordinances. Follow details in
		Installation Instructions.
		If not grounded properly, break down and leakage of electricity may occur, which may
		cause electric shock.
		• Must be positioned so that the plug is accessible.
		If the plug is placed between the wall and the machine, it may get damaged, possibly
		causing fire or electric shock.
		• Make sure the plug is completely pushed into the outlet.
		Failure to do so may cause electric shock and fire due to overheating.

5

Safety Information

	WARNING	<![if ! IE]> <![endif]>r
YOUR		<![if ! IE]> <![endif]>Intc
LAUNDRY		<![if ! IE]> <![endif]>odu
AREA	• Keep the area underneath and around your appliances free of combustible
	materials such as lint, paper, rags, chemical, etc.	<![if ! IE]> <![endif]>tion
	Operating with such materials around the machine may trigger
	explosion or fire.

•Close supervision is necessary if this appliance is used by or near children.

Do not allow children to play on, with, or inside this or any other appliance.

There is potential danger that children might drown or suffocate in the tub.

Do not touch the power plug with a wet hand.

It will cause electric shock

Do not put your hand, foot or anything under the washing machine

while the washing machine is in operation.

There is a rotating mechanism under the machine, so you could be injured.

WHEN USING	CAUTION
THE WASHER

•Use this appliance only for its intended purpose as described in this Owner’s Manual.

•The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by person responsible for their safety, Children should be supervised to ensure that they do not play with the appliance

•To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

NOTE : Pressing Circuit button to turn off does NOT disconnect the appliance from the power supply.

•Make sure that drainage is working properly.

If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.

•If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving.

Wait until the machine has completely stopped before opening the lid.

Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

Operating with a damaged plug may cause electric shock.

Do not use water hotter than 50°C.

Use of excessively hot water may cause damage to fabrics or cause leakage of water.

6

<![if ! IE]>

<![endif]>Introduction

Safety Information

	WHEN USING	WARNING
	THE WASHER

Do not use a plug socket and wiring equipment for more than their rated capacity.

Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.

Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce toxic gases which may cause death.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.

Do not use or place these substances around your washer or dryer during operation.

		It may ignite or explode.
	WHEN NOT	CAUTION
	IN USE

•Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.

•When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.

•Wipe off dirt or dust on the contacts of the power plug.

Using unclean power plug may cause fire.

•Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.

Children may be trapped and suffocated if the lid is left intact.

Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.

Operating the machine with improperly replaced parts may be a cause for fire or electric shock.

Do not tamper with controls.

It may lead to electric shock, fire , break down, deformation.

Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.

Failure to observe these instructions may cause electric shock or fire due to short-circuit .

When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.

It will cause short circuit and electric shock.

Identification of Parts

Body

POWDER AND LIQUID

DETERGENT BOX

LINT FILTER

Clean regularly to reduce linting

** Only WF-HD950GV / WFT956DD / T8503AECT5

BLEACH

DISPENSER

FUNCTION

SELECTOR

TUB

START/PAUSE BUTTON

Use to start or stop the washing machine temporarily.

ADJUSTABLE LEGS

Use to level the washing machine for correct balance & spin operation.

WATER SUPPLY HOSE

Make sure the water does not leak.

POWER PLUG

If the supply cord is

damaged, it must be

replaced by the

manufacturer or its

service agents or

similarly qualified

person in order to avoid a hazard.

JET SPRAY

DRAIN HOSE for pump model

Ensure that the drain hose is hung up

before operating the washing machine.

BASE

Accessories

Water supply hoses	Drain hose	Anti-rat cover (option)
	For Non-Pump Model
or
	For Pump Model	or

1 Each for COLD and HOT water

NOTE

“*” Part can be different according to the model.

7

<![if ! IE]>

<![endif]>on rodu Inct ti

8

<![if ! IE]>

<![endif]>Introduction

Function Information

Our machine provides various washing methods which suits various conditions and types of laundry.

Different types of laundry washing

FUZZY(Normal) Wash

	Use this Program for everyday washing e.g. sheets, towels, T-shirts.			(refer to page 16)
	Use this Program for heavily soiled durable garments e.g. overalls, jeans.			(refer to page 16)
	Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed.
	SMART CLEANING
			(refer to page 16)
	Use this program to get better rising performance.
	Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed.			(refer to page 16)

The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.

Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them

•Before washing your woolens check the care label for the washing instructions.

•When washing woolens use a mild Detergent recommended for washing wool.

•Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.

•To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)

Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to handwash these articles and place them in the machine to spin dry.

FAVORITE Wash

	This setting allows you to store your FAVORITE wash conditions in the normal cycle memory.		(refer to page 19)
	SILENT Wash
		(refer to page 20)
	Use this program to wash quietly at night.

Washing according to the condition of laundry

QUICK WASH

QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time.

(refer to page 16)

SOAK Wash

SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 18)

Other washing method

TUB CLEAN

	Use this program to clean the inside of washing machine especially Inner tub & Outer tub .		(refer to page 21)

(refer to page 24)

WASH, WASH/RINSE/SPIN,

Preparation Before Washing

Care Labels

* Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

Sorting

To get the best results, different fabrics need to be washed in different ways.

•	SOIL	(Heavy, Normal, Light)	Separate clothes according to the type and amount of soil.
•	COLOR	(Whites, Lights, Darks)	Separate white fabrics from colored fabrics.
•	LINT	(Lint producers, Collectors)	Separate lint producers and lint collectors.
Lint Producers			Terry cloth, Chenille, Towels, Nappies, Diapers
Lint Collectors			Synthetics, Corduroy, Permanent Press, Socks

Check before Loading

•	Check all pockets to make sure that they are empty		. Things such as nails, hairclips, matches,
	pens, coins, and keys can damage both your washer and your clothes.
•	Mend any torn garments or loose buttons		. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
•	Pretreat any dirt and stains	.
• Make sure the clothes are washable in water.			WIRE

•Check the washing instructions.

•Remove tissue in pockets.

Pretreatment on stains or heavy soil

when placing them in the washer. of water and granular Detergent.

they are to remove.

Loading

	.		WARNING
			Fire Hazard
			Never place items in the washer that are
			dampened with gasoline or other flammable
			fluids.
			No washer can completely remove oil.
		.	Do not dry anything that has ever had any type
			of oil on it (including cooking oils).
Light and Large-sized clothing			Doing so can result in death, explosion, or fire.

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Long laundry items

Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent

tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes. Nylon net is not supplied by LG.

9

<![if ! IE]>

<![endif]>Wash to Starting Before

10

<![if ! IE]>

<![endif]>Before Starting to Wash

Use of Water, Dispenser Drawer, Detergent and Softener

Using Water

Amount of WATER LEVEL

, then sets the

will be shown on the

it may differ depending LEVEL is indicated

NOTE

[ Minimum water amount ]

It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub

directly to some height. That’s because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.

Water Temperature (for 2 valve model)

• The machine sets the appropriate temperature automatically according to the wash program .

, the cleaning results.

and heavily soiled, colorfast items.

with light soil.

lint, residue, poor cleaning, etc. …(80-85˚F).

not activate and clean effectively.

NOTE

If iron is present in the	water the clothes may become an all-over yellow or they may be stained with brown or orange
spots or streaks. Iron is	not always visible. Installation of water softener or an iron filter may be necessary for severe case	s.

Using the Dispenser Drawer

The dispenser drawer contains 2 compartments:

• Liquid Fabric Softener

• Liquid or Powder Low-Sudsing, High-Efficiency Detergent

The dispenser automatically dispenses additives at the proper time in the wash cycle. 1. Slowly open the dispenser drawer by pulling the drawer out until it stops. 2. After adding laundry products, slowly close the dispenser drawer. Closing the

drawer too quickly could result in early dispensing of additives.

•Avoid overfilling or splashing when adding laundry products to the dispenser. Doing so could result in early dispensing of laundry products.

At the end of the cycle, you may see water in the compartments. This is part of the normal operation of the washer.

NOTE : Do not use bleach in the dispenser drawer.

Using Detergent

Detergent

Follow the Detergent package directions. Using too much Detergent is a common cause of laundry problems Use more Detergent if you have hard water, large loads, greasy or oily soils or higher Water Temperature.

Choosing the right Detergent

We recommend the use of front loader type, low sudsing high efficiency Detergent(powder,liquid or concentrated).

Soap flakes or granulated soap powders should not be used in your washing machine.When washing woolens Remember to use Detergent suitable for washing woolens.

Using Detergent

How much Detergent

The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work clothes may need more Detergent, while bath towels usually need less.).

For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.

Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine.

If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, And long term scrud build up.

Adding Detergent

Add measured detergent to the detergent compartment of the dispenser drawer.

We recommend the use of powdered detergent in the dispenser when using a delay wash function. We recommend to dissolve measured detergent in 1 liter warm water before addition to the machine.

Detergent is flushed through the dispenser at the beginning of the wash phase.

Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load. Avoid using too much detergent in your washer, as it can lead to oversudsing and detergent residue being left on the clothes.

(Only WF-HD950GV / WFT956DD / T8503AECT5)

11

<![if ! IE]>

<![endif]>Wash to Starting ore Be f

12

<![if ! IE]>

<![endif]>Before Starting to Wash

Use of Water, Dispenser Drawer, Detergent and Softener

Using Fabric Softener

If desired, pour the recommended amount of liquid fabric softener into the right-hand compartment.

Use only liquid fabric softener.

Dilute with water to the maximum fill line.

• Do not exceed the maximum fill line.

Overfilling can cause early dispensing of the fabric softener, which could stain clothes.

NOTE : Do not pour fabric softener directly on the wash load. It may stain the clothes.

Attention

Do not mix with Detergent or bleach.

Never pour fabric softener directly on clothes. It may stain them.

Do not stop the washer during the first spin for timely dispensing.

Option washing is not designed to be used with fabric softener dispenser.

Scrud(Waxy Build up)

Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.

If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.

If you wish to use fabric softener we recommend

•Using fabric softener sparingly.

•When filling the dispenser, do not splash or overfill.

•Clean dispenser as soon as the cycle is finished.

• Clean your machine regularly.

(refer to page 21 or 32)

•Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or HOT wash e.g. every 5th wash should be at least a warm one.

•Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.

Special Guide for Stain Removal

WARNING

Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death. To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:

• Read and comply with all instructions on stain removal products.

•Keep stain removal products in their original labeled containers and out of children’s reach.

•Thoroughly wash any utensil used.

•Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.

•Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.

•Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.

13

<![if ! IE]>

<![endif]>Wash to Starting Before

For successful stain removal:

•Remove stains promptly.

•Determine the kind of stain, then follow the recommended treatment in the stain removal chart below.

•To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.

•Use COLD water on unknown stains because HOT water can set stains.

•Check care label instructions for treatments to avoid on specific fabrics.

•Check for colorfastness by testing stain remover on an inside seam.

•Rinse and wash items after stain removal.

Follow fabric care label instructions

			Stain Removal
	STAIN		TREATMENT
	Adhesive tape, chewing gum,	Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
	rubber cement	nonflammable dry cleaning fluid.
	Baby formula, dairy products, egg	Use product containing enzymes to pretreat or soak stains.
	Beverages (coffee, tea, soda, juice,	Pretreat stain. Wash using COLD water and bleach safe for fabric.
	alcoholic beverages)
	Blood	Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
		bleach safe for fabric.
	Candle wax, crayon	Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
		Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
		fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
	Chocolate	Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
	Collar or cuff soil, cosmetics	Pretreat with prewash stain remover or rub with bar soap.
	Dye transfer on white fabric	Use packaged color remover. Wash using bleach safe for fabric.
	Grass	Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
	Grease, oil, tar (butter, fats, salad	Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
	dressing, cooking oils, car grease,	nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
	motor oils)	using hottest water safe for fabric.
	Ink	Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
		alcohol or nonflammable dry cleaning fluid.
	Mildew, scorch	Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
		mildewed fabrics may be permanently damaged.
	Mud	Brush off dry mud. Pretreat or soak with product containing enzymes.
	Mustard, tomato	Pretreat with prewash stain remover. Wash using bleach safe for fabric.
	Nail polish	May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
		Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
	Paint, varnish	WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
		OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
	Rust, brown or yellow	For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
	discoloration	nonchlorine bleach.	Do not use chlorine bleach because it may intensify discoloration.
	Shoe polish	LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
		prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
		safe for fabric.

14

<![if ! IE]>

<![endif]>Before Starting to Wash

F unction of each Button

BEEPER BUTTON

• Use to select Beeper Pressing the button allows

HIGH OFF LOW HIGH respectively.

	WATER BUTTON	TIME LEFT, DELAY START
		(RESERVATION), ALARM INDICATION
	• Use to select the proper amount of water in relation	• Time left	- During operation, the remaining time
	to the weight and type of laundry.		is indicated.
	• Automatically controlled,but can be selected	• DELAY START INDICATION
	manually by pressing the WATER Botton.	(RESERVATION)		- When DELAY START
	• WATER is automatically selected for	(RESERVATION) program is selected, it
	FUZZY(normal) program.	indicates the finishing time. (RES.=DELAY)
	The following settings are indicated as the button is	• Alarm indication		- When an error occurs, an error
	pushed	message appears to indicate the abnormality.
	7 8 9 10 1 2 3 4 5 6 7	For example,		indicates that the lid is open.

AIR DRY

•This function is used to reduce the drying time of the laundry by allowing air to circulate within the bowl in order to reduce moisture levels.It does not dry the clothes completely.

•Air dry selections light up in sequence as follows.

60 90

120 60 as the button is pushed.

•Press the button for 3 seconds to select and press the Power botton to cancel the operation.

(refer to page 22)

SOIL LEVEL BUTTON

•This button allows you to select the strength of the wash action.

•Power option selections light up in sequence as

follows Normal	Heavy
Light	Normal as the
button is pushed.

This can be selected for any program.

•Adjustment can be made while washing.

NOTE

TUB DRY		WASH. RINSE. SPIN BUTTON
• Use this when you		• Use when wash, rinse, spin
want to dry the		time need to be adjusted.
empty tub after a		• The time increases when the
wash.		button is pressed .
• This can be		• If adjustments are needed
set/canceled by		during the wash,press the
pressing the Wash		[start/pause ] button before
button and Rinse		making any changes.
button		• When the button is pressed
simultaneously.		during washing,the
(refer to page 22)		remaining time is displayed.

CHILD LOCK FUNCTION

•Use to lock or unlock the control buttons to prevent settings from being changed by a child.

To lock,push the RINSE and SPIN buttons simultaneously and to unlock push them one more time during the washing process.

(refer to page 25)

*For optimizing the washing algorithm, the displaying time may be changed during washing-increased by 8minutes at maximum and decreased by 4 minutes at maximum.

*If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically adds rinsing, and the remaining time may be increased.

*The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to

the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit. * The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a

liquid one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.

WASHING CONDITION INDICATOR (OPTION)

•It only operates in FUZZY Program.

•During being detected by the sensor, the LED flashes green, orange

and red in turn. And, after detecting, the LED lights a specific color according to the detecting condition as follows:

If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength, and the LED automatically turns to red.

If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by increasing washing time/strength, and the LED automatically turns to orange.

If the current washing condition is determined as equal to the standard one, the algorithm has no change and the LED turns to green.

POWER(AUTO OFF)

BUTTON

• Use to turn the power on or off.

• Push again and power goes on or off

• The power goes off automatically about 10 seconds after the wash is finished.

15

<![if ! IE]>

<![endif]>as h to Starting Before

DELAY START (RESERVATION) BUTTON

•Use to set a delayed finishing time.

•The time increases when the button is pushed.

•The following settings are indicated

as the button is pushed 3	4	5
... 11 12 14 16	...46	48

3HOUR.

•To cancel delay time, turn the power switch off.

(refer to page 24)

PROGRAM BUTTON

•Use for selecting wash program.

•This button allows you to select 8 different programs for different kinds of laundry and dirtiness.

•program selections light up in sequence as

follows: FUZZY(Normal)		WOOL
QUICK WASH	JEANS	SMART
CLEANING SILENT FAVORITE
TUB CLEAN	FUZZY(Normal) etc.

Select the desired program by pressing the button.

START/PAUSE BUTTON

•Use to start or pause the washing process.

•Repeats start and pause by pushing the button.

*Because the detecting ability of the sensor may be decreased by using it for a long time, periodically use TUB CLEAN course to clean the tub. (refer to page 21)

*Even if the water level is changed by the user in FUZZY(Normal) Program, the sensor will still work. The sensor algorithm may differ according to models.

*The control panel may differ according to different models.

16

<![if ! IE]>

<![endif]>Washing Programs

Washing Programs

Washing		Add		Add
		the
Programs				the Detergent
		laundry
(Normal Wash)	1	2		4
Used for normal loads, this				• Add the appropriate
mode automatically selects the
most appropriate conditions				quantity of Detergent
and completes the sequence				as indicated by the
in one operation. The built-in				WATER LEVEL.
sensor detects the size of the				Or follow the
load and the ideal wash				Detergent
power and wash, rinse and				manufacturer’s
spin times are set accordingly.				instructions
Use this program for washing	1	3	2	5
			• Select the	• Use neutral
delicate fabrics such as lingerie and
woolens. (wash only “water			WOOL	Detergent
washable” clothes)			program on	appropriate for the
Before washing your woolens			the Control	laundry.
			panel.	• When washing
check the care label for the
				woolens use a mild
washing instructions.
				Detergent
(wash only water washable clothes)				recommended for
				washing wool.
	1	3	2	5
Use this mode when washing			• Select the	• Add the appropriate
lightly soiled clothes for a short			QUICK	quantity of Detergent
time. The highly recommended			WASH	as indicated by the
			program on	WATER LEVEL.
laundry amount is under 2.0kg.
			the Control	Or follow the
			panel.	Detergent
				manufacturer’s
				instructions
	1	3	2	5
Use Jean program when		• Spread	• Select the
washing Jeans of different sizes		the jean	JEANS
		evenly in	program on
		the tub	the Control
			panel.
Use this program to increase	1	3	2	5
rinsing performance.			• Select the
This would include underwear
			SMART
and baby clothes.
			CLEANING
If someone has sensitive skin or
			program on the
skin trouble,use this program.			Control panel.

					Close the lid				Finish	Caution & Note
	3				5			6		• If water is already in the tub, or putting
										wet laundry into the tub before starting
										will increase the WATER LEVEL.
	• The pulsator rotates for				• Water will be				• When the wash	• With lightweight bulky loads, WATER
	8 seconds to detect the				supplied for 2				program ends, the	LEVEL can be set low.
	laundry load.				minutes after the				buzzer will ring
	• Then the WATER LEVEL				start of the wash to				for 10 seconds
	and the amount of				supplement the				before the Power
	Detergent to be used				water the laundry				goes off
	will be shown and				has absorbed.				automatically.
	water will be supplied.
										• When setting the WATER LEVEL
					6				7	manually, do not set to Medium to
	4
										prevent damage to laundry.
										• Washing with HOT water may damage
										the laundry (Water is set to cold
										automatically). Ensure that the load is
										under 2kg.
										• In order to avoid damage to laundry,
										the spin cycle may appear slow.
										This also avoids wrinkles and clothing
										may still contain some water. This is
										normal.
										• When static pressure of water is more
	4				6			7		than 2kg/cm2, the QUICK WASH course
										will be within 19min.

4

6

7

4

6

7

17

<![if ! IE]>

<![endif]>Programs Washing

18

<![if ! IE]>

<![endif]>Washing Programs

SOAK Wash

Use this mode to wash normal clothes or thick and heavy clothes which are excessively dirty. SOAK mode can be used with FUZZY or JEAN or SILENT or FAVORITE program.

1 Press the POWER (AUTO OFF) button to turn power on.

2 Press the PROGRAM button to select the washing program.

3 Press the WASH button, to select SOAK program.

•Keep pressing the WASH button until the light turns on ‘SOAK’ and ‘WASH’ simultaneously as next image.

	• SOAK program only works when socking time is 40, 50 or
	60 minutes.
4 Add the Detergent.	• Add the appropriate quantity of Detergent as the Detergent
	manufacture instruction.

5 Add the laundry and press the START/PAUSE button.

		• The WATER LEVEL	will be shown and water will be
		supplied.
6	Close the lid.	• Water will be supplied for 2 minutes after the start of the
		wash to supplement the absorbed water by the laundry.
	Finish	• When the wash program ends, the buzzer will ring for
		10seconds before the Power goes off automatically.

NOTE

• Order of Soak-Wash timing

Soak-Wash

Lamp

min

min

min

min

min

min

min

min

Off

min

min

min

min

min

•Select soaking time 40minutes, 50minutes, or 60minutes (including washing time) by pressing the Wash button repeatedly.

•If necessary, select the times of Rinse and the time for Spinning by pressing the Rinse or Spin buttons till you reach the desired times.

FAVORITE Wash

Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the normal cycle memory and then recall it for use at a later time.

1 Press the POWER (AUTO OFF) button to turn power on.

2 Select the FAVORITE program.

19

<![if ! IE]>

<![endif]>Programs Washing

3 Select your FAVORITE wash conditions.

• Press the	WATER	button to select		WATER	.
• Press the	WASH	button, the	RINSE	button & the SPIN
button to select wash time, rinse time & spin time
respectively you want to store.

4 Press the START/PAUSE button to store & start your FAVORITE wash cycle. Power turns off automatically after wash.

NOTE

To recall your FAVORITE cycle.

1.Press POWER on.

2.Select the FAVORITE cycle by pressing the PROGRAM.

3.Press the START/PAUSE button. Then the wash cycle starts.

20

<![if ! IE]>

<![endif]>Washing Programs

SILENT Wash

Use this program to wash quietly in SILENT especially during late night and dawn.

1 Press the POWER (AUTO OFF) button to turn power on.

2 Press the PROGRAM button to select SILENT program.

3 Add the laundry into the washing tub.

4 Press the START/PAUSE button.

5 Add the Detergent and close the lid.

NOTE

•SILENT program takes longer washing time than FUZZY(Normal) program.

•To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has more moisture than normal.

TUB CLEAN

If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer.

Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub.

1 Press the POWER (AUTO OFF) button to turn power on.

2 Press the PROGRAM button to select the TUB CLEAN program.

21

<![if ! IE]>

<![endif]>Program Function Additional

3 Press the START/PAUSE button. • Left time is displayed.

4	After 10 minutes of water supplement. Add the oxygenated bleach (about 300 m ).
	• Do not use Detergent box.
	• Do not place any laundry inside tub.
5	Close the lid.	• When the lid is open the machine will not operate, and an
		alarm signal will remind you to close the lid.

NOTE

•Before using this program remove lint inside lint filter.

•When using this program, do not place any laundry inside tub.

•This program takes about 3 hours to be completed.

•After using this program, remove dirt inside filter.

•After finishing this program, open the lid of wash to remove irritant odor.

•Do not pour bleach into the tub directly. It might cause damage the tub.

•Do not leave diluted oxygenated bleach inside tub for long time.

It rusts the tub must drain the remained diluted oxygenated water out.

•Use this program once for every month.

•Do not use this program repeatedly.

22

<![if ! IE]>

<![endif]>Additional Function Program

AIR DRY

AIR DRY for your laundary.

1	Press the POWER (AUTO OFF) button to turn power on.
2	When you press the Air dry button for 3 seconds, the Air dry course will be
	selected.	• When the Air dry is selected, other buttons will be inactive.
		• If you want to cancel the Air dry function, press the Power button.
3	Press the START/PAUSE button.
4	When the Complete buzzer goes off, the power will automatically be turned
	off in 10 seconds.

NOTE

When you select Air dry foir more than 60 minutes

1)You can reduce the drying time by minimizing the moisture in the laundry.

2)Always keep the laundry amount to 2kg or less and make sure to spread it out evenly.

3)Select 60 minutes for cotton laundry and 120 minutes for synthetic fiber laundry for effective Moisture removal.

TUB DRY

1	Press the POWER (AUTO OFF) button.
2	When you press the Wash and Rinse button simultaneously, the Tub Dry course
	will be set or canceled.
	• When you select the Tub Dry, do not put any laundry in the drum.
	• When Tub Dry is selected, other buttons will be inactive.
3	Press the START/PAUSE button.
4	When the Complete buzzer goes off, the poser will automatically be turned off in
	10 seconds.

NOTE

When you select Tub Dry

1)Use this function to minimize the growth of mold from the residual moisture within the laundry.

2)When you select the Tub Dry course, do not put any laundry or detergent in the drum.

3)It is good to use this about once a week.

Option Washing

When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.

1 Press the POWER (AUTO OFF) button to turn power on.

2	Only Wash			Only Rinse			Only Spin
	Press the	WASH	button to	Press the	RINSE	button to	Press the SPIN button to
	select the desired timing.			select the desired times of			select the desired times of
				rinse.			spin.
	Only Wash,Rinse			Only Rinse,Spin			Only Drain
	Press the	WASH	button to	Press the	RINSE	button to	When you want to only
	select the desired timing.			select the desired times of			drain, wait until the water
				rinse.			in the washing tub drains
							completely.
	Press the	RINSE	button to
	select the desired times of			Press the	SPIN	button to
	rinse.			select the desired times of
				spin.
	You can use this option
	for preventing wrinkles of
	laundry

3 Press the WATER button, to control the water level according to the amount of laundry. If you do not choose anything, it is set the middle water level automatically.

4 Add the laundry into the washing tub.

5 Press the START/PAUSE button.

6 Add the detergent and close the lid.

NOTE

• When a Wash, Wash/Rinse or Rinse only option			is selected, after the wash is completed the water will not
be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained
completely. Then press the	START/PAUSE		button.
• If you do not specify the water level		, then Medium will be automatically selected.

• If only Rinse is selected, the process will start from Water Supply.

23

<![if ! IE]>

<![endif]>Program Function Additional

24

<![if ! IE]>

<![endif]>Additional Function Program

DELAY START (RESERVATION) Wash

DELAY START (RESERVATION) Wash is used to delay the finishing time of the operation. The hours to be delayed can be set by the user accordingly.

The time on the display is the finishing time , not the start time.

1	Press the POWER (AUTO OFF) button to turn power on.
2	Press the PROGRAM button to select the washing program.
	• Select the program for laundry on the Control panel.
	This program will not work in WOOL and TUB CLEAN
	Program.
3	Press the DELAY START (RESERVATION) button.
	• The light will ‘DELAY’ turn on and
	‘TIME LEFT’	be marked.
	• Press the button repeatedly to set the desired finishing time.
	For example, To finish washing in 9 hours from now,		by
	make the number 9:00 pressing the		DELAY START
	(RESERVATION )	button repeatedly.

(RES.=DELAY)

4 Add the Detergent. • Add the appropriate quantity of Detergent as the Detergent manufacture instruction.

•When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid

	5	Add the laundry and press the START/PAUSE button.
			• When you press the	START/PAUSE button the light will
			blink.
	6	Close the lid.	• Water will be supplied for 2 minutes after the start of the
			wash to supplement the water the laundry has absorbed.
		Finish	• The washing will be finished according to the delayed time.

NOTE

• Finishing time can be delayed from 3~48 hours. Delaying from3~12 hours can be done in 1 hour time intervals and from 12~48 hours in 2 hour time intervals.

• If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.

•To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the

DELAY START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.

•When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning program . (The laundry will be wrinkled if left for a long time after spinning.)