Please read this manual carefully before operating your set.
Retain it for future reference.
Record model name and serial number of the set.
Quote this information to your dealer when you require service.
PT. LG ELECTRONICS INDONESIA
Kawasan Industri MM 2100 Blok G
Cikarang Barat, Bekasi, Jawa Barat
INDONESIA
Washer doesn't operate while the lid is open. If the lid is open during the wash,
rinse or spin cycles, the operation stops for safety.
Fuzzy logic control
Turbo drum washing (option)
A built-in load sensor automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal water level
and washing time.
SENSING
START
Water Level Sensor
Advanced technology is built into the Electronic Control System which
ensures the best washing result.
When "Punch + 3" washing wings turn, the washing
tub turns in the opposite direction. This makes the
both sides current of water which improve washperformance by rubbing clothes strongly.
Washing
Condition
WASHING
SETTING
Optimum
Laundry Sensor
AUTO
POWER
OFF
3 Step washing
3 step washing makes the best washing performance with low tangling.
Rubbing
Rubbing and
Shaking
Shaking and
Disentangling
C
ontents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you
may not need to call for service at all.
Introduction
Before Starting to Wash
Washing Programs
Additio nal Functio n
Options
Installation
Safety Information
Identification of Parts
Function Information
Preparation Before Washing
Use of Water, Detergent, Bleach and Softener
Special Guide for Stain Removal
Function of each Button
Fuzzy Wash (Normal Wash)
Wool Wash
Soak Wash
Q.Wash
Delay Start (Reservation) Wash
Option Washing
Other Useful Functions
Placing and Leveling
Connecting Water Supply Hose
Connecting Drain Hose
11
12
14
14
14
14
16
17
19
21
22
25
4
5
6
7
8
Care and Maintenance
Troubleshooting
Terms of Warranty
Specification
Grounding Method
Cleaning and Maintenance
Common washing problems
Troubleshooting
Terms of Warranty
Specification
26
27
29
30
31
32
4
afety Information
Introduction
S
WATER HEATER
SAFETY
PROPER
INSTALLATION
YOUR
LAUNDRY
AREA
WHEN USING
THE WASHER
WHEN NOT IN
USE
WARNING!
Read and follow this safety information carefully.
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, personal injury, or loss of life.
Save these instructions.
• Under certain conditions hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances. If the
hot water has not been used for two weeks or more, prevent the possibility of damage or injury
by turning on all hot water faucets and allowing them to run for several minutes. Do this before
using any electrical appliance which is connected to the hot water system. This simple
procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not
smoke or use an open flame or appliance during this process.
• The base opening must not be obstructed by carpeting when the washing machine is installed on
a carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
• Must be positioned so that the plug is accessible.
• Keep the area underneath and around your appliances free of combustible materials such as lint,
paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance is used by or near children. Do not allow children
to play on, with, or inside this or any other appliance.
• Use this appliance only for its intended purpose as described in this Owner's Manual.
• Never reach into washer while it is moving. Wait until the machine has completely stopped
before opening the lid.
• Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing
different chemicals can produce a toxic gas which may cause death.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents,
kerosene, etc.) which may ignite or explode. Do not add these substances to the wash water. Do
not use or place these substances around your washer or dryer during operation.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully
follow the garment manufacturer's wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power supply or
disconnect the washer at the household distribution panel by removing the fuse or switching off
the circuit breaker before attempting any maintenance or cleaning.
NOTE: Pressing Power button to turn off does NOT disconnect the appliance
from the power supply.
• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled,
or has missing or broken parts, including a damaged cord or plug.
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break
or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5
years.
• Before discarding a washer, or removing it from service, remove the washer lid to prevent
children from hiding inside.
• Do not attempt to repair or replace any part of this appliance unless specifically recommended in
this Owner's Manual, or in published user-repair instructions that you understand and have the
skills to carry out.
• Do not tamper with controls.
dentification of Parts
I
Body
5
Introduction
Accessories
Water supply hoses
Note
Part can be different according to the model.
Drain hoseAnti-rat cover (option)
6
unction Information
F
Our machine provides various washing methods which suits various conditions and
types of laundry.
Different types of laundry washing
Introduction
Fuzzy(Normal) Wash
Use this Program for everyday washing e.g. sheets, towels, T-shirts.
Wool Wash
Delicate clothes (lingerie, wool, etc.) which may be easily damaged can be washed.
The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
• Before washing your woolens check the care label for the washing instructions.
• When washing woolens use a mild detergent recommended for washing wool.
• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and
tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to
handwash these articles and place them in the machine to spin dry.
Washing according to the condition of laundry
Q.Wash
Q.Wash can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time.
(refer to page14)
Soak Wash
Soak Wash is designed to maximize washing performance and can be selected to wash heavily
soiled laundry with Fuzzy Program.
Other washing method
Delay start Wash
Delay start Wash is used to delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly.
(refer to page14)
(refer to page14)
(refer to page14)
(refer to page16)
Option Wash
When the user needs only Spin, Rinse/Spin, Rinse, Wash/Rinse, Wash, Wash/Rinse/Spin,
Soak/Wash/Rinse/Spin.
(refer to page17)
7
reparation Before Washing
P
Care Labels
* Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle, water temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light)
• COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
• LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
• Check all pockets to make sure that they are empty . Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue in pockets.
Pretreatment on stains or heavy soil
• Pretreat shirt collars and cuffs with a pre-wash product or liquid detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid detergent or a paste of water and granular detergent.
• Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page11)
Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The water level should just cover the clothes. Adjust the load size accordingly.
Loosely load clothes no higher than the top row of holes in the washer tub. To
add items after washer has started, press Start button and submerge additional
items. Close the lid and press Start button again to restart.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved detergent to prevent the detergent from clumping.
Long laundry items
Use nylon nets for long, delicate items. For laundry with long strings or long length , a net will prevent
tangling during washing.
other clothes.
Nylon net is not supplied by LG.
Fasten zippers, hook, and strings To make sure that these items don't snag on
Separate clothes according to the type and amount of soil.
Tears or holes may become larger during washing.
Never place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING
Fire Hazard
Before Starting to Wash
WIRE
8
U
Using Water
Before Starting to Wash
Using Detergent
se of Water, Detergent, Bleach and Softener
Amount of Water Level
• This machine detects the quantity of laundry automatically, then sets the water
level and proper amount of detergent.
• When you select a wash program, the water level and amount of detergent (to be used)
will be shown on the control panel.
• The following table shows the amount of water.
• When the water level is automatically detected, it may differ depending on the quantity of laundry even
though the same water level is indicated on the control panel.
• The amount of a cup in the diagram is about 40g for concentrated detergent.
Attention
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown
or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be
necessary for severe cases.
Detergent
Follow the detergent package directions. Using too little detergent is a common cause of laundry problems.
Use more detergent if you have hard water, large loads, greasy or oily soils or lower water temperature.
Choosing the right detergent
We recommend the use of domestic detergent, (powder, liquid or concentrated). Soap flakes or
granulated soap powders should not be used in your washing machine. When washing woolens
remember to use detergent suitable for washing woolens.
Using Detergent
How much detergent
When you select a wash program the water level and the amount of detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated
detergent.
The correct amount of detergent will vary depending on the amount of soil in your clothes (Jeans
and work cloches may need more detergent, while bath towels usually need less.).
For liquid and concentrated detergents, follow the recommendations of the detergent manufacturer.
Note: To check you are using the correct amount of detergent, lift the lid of your machine
about half-way through the wash. There should be a thin layer of foam over the surface of the
water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No
foam means not enough detergent has been used; soil and lint can settle back on the clothes or
the washing machine.
If excess detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
Attentión
Adding the detergent
9
Before Starting to Wash
Open the detergent dispenser and deposit the appropriate
amount of detergent
where you deposit the detergent
Powder Detergent dispenser.
Some detergents MUST be fully dissolved before
adding to your machine to get the best wash results.
Check the instructions on the detergent packet.
If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water
before being added to warm or hot water for the actual wash.
Pre-dissolving detergent in warm water when washing in cold water can improve its performance.
Where you
D nde
deposit the
depo\bta e
detergent
detergente
Powder Detergent Box
D\bpen\bador de detergente en po\f
( )
Using Liquid Bleach
• Check clothing care label for special instructions and separate the
laundry to be bleached
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully
following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
Attention
•
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
•
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover. Mixing can reduce
a toxic gas which may cause death.
•
Do not pour powdered bleach into bleach dispenser.
Bleach dispenser
( )
10
U
Using Fabric Softener
• Dilute fabric softener with water.
• Measure and add the recommended amount of fabric softener
Before Starting to Wash
• Do not overfill. The dispenser hold max 35mL.
• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its
se of Water, Detergent, Bleach and Softener
Undiluted fabric softener may result in spots that look like oil
stains.
into the compartment marked with this symbol().
Follow manufacturer’s direction.
•
Fabric softener is automatically dispensed in the final rinse
with indication beep.
•
If you want extra rinse, you must add fabric softenermanuallywhen indication beep rings in the final rinse.
This maximize the fabric softener function.
Never add more than 35mL.
Overfilling can cause early dispensing of the fabric softener
which could result in stained clothes. A cup with a pouring spout will help you avoid spilling.
effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually
put during the time when the washer beeps several times before the final rinse. This function informing
correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric
softener has to be diluted with water before dispensed and never poured directly on clothes.
Softener dispenser ( )
or
Attention
Do not mix with detergent or bleach.
•
•
Never pour fabric softener directly on clothes. It may stain them.
•
Do not stop the washer during the first spin for timely dispensing.
•
Option washing is not designed to be used with fabric softener dispenser.
Scrud(Waxy Build up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant
smell in your washer.
If you wish to use fabric softener we recommend
• Using fabric softener sparingly.
• When filling the dispenser, do not splash or overfill.
• Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 27)
• Cold water washing increases the chance of this build-up occurring. We recommend a regular warm or hot
wash e.g. every 5th wash should be at least a warm one.
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a
build-up.
11
pecial Guide for Stain Removal
S
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled containers and out of children’s reach.
• Thoroughly wash any utensil used.
• Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or explosive substances because they give off vapors that could ignite or explode.
• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain
removal chart below.
• To pretreat stains, use a prewash product, liquid detergent, or a paste made from
granular detergent and water.
• Use cold water on unknown stains because hot water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
Chocolate
Collar or cuff soil, cosmetics
Dye transfer on white fabric
Grass
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
Nail polish
Paint, varnish
Rust, brown or yellow
discoloration
Shoe polish
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using bleach
safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub detergent into dampened area, Wash using bleach
safe for fabric.
TREATMENT
Follow fabric care label
instructions
Before Starting to Wash
12
unction of each Button
F
Delay Start
(Reservation) button
Use to set a delayed finishing time.
•
Before Starting to Wash
The time changes
-> 14 -> 16 -> ... 48 -> 3 ]
when the button is pushed.
(refer to page 16)
[ 3 -> 4 -> 5 -> ...12 ->
Use to adjust the water level as required. The appropriate
•
amount of detergent is shown next to the water level in
the Water-Detergent diagram
• Water level is automatically selected for fuzzy (normal)
programs.
The following settings are indicated as the button is
pushed 9 --> 10 --> 1 --> 2 --> 3 --> 4 --> 5 --> 6
--> 7 --> 8 --> 9
Water level button
(indication of detergent amount)
Time left, Delay Start (Reservation),
Alarm Indication
Time left - During operation, the remaining time
•
is indicated.
• Delay Star t indication (R eservation) - When
delay start (reservation) program is selected, it indicates
the finishing time. (RES.=DELAY)
• Alarm indication -When an error occurs, an error message
appears to indicate the abnormality.
For example, “ dE ” indicates that the lid is open.
Note
The control panel may differ according to different models
Tub Clean function
Use to clean inner tub and outer tub to
•
prevent scrud buiding up in the machine.
Before Starting to Wash
13
Start/Pause button
• Use to start or pause the washing process.
• Repeats start and pause by pushing the button.
• The power goes off automatically 10 minutes
after stopping.
Program button
• Use for selecting wash program.
• This button allows you to select 4
different programs for different kinds
of laundry and dirtiness.
• Program selections light up in sequence
as follows: Fuzzy (Normal) -> Q.Wash ->
Select the desired program by pressing
the button.
Wool - > Air Dry.
Process button
• Use to select Soak,
Wash, Rinse and
Spin functions
as desired.
ON / OFF button
• Use to turn the power on or off.
• Push again and power goes on
• The power goes off automatically
is finished.
or off
about 10 seconds after the wash
Child lock function
Use to lock or unlock the control buttons to
prevent settings from being changed by a child.
To lock, push both the PROCESS, and PROGRAM
buttons simultaneously and to unlock push them
one more time during the washing process.
(refer to page 20)
•
Washing Programs
14
W
ashing Programs
Washing
Programs
Add
the
laundry
Add
the detergent
Fuzzy Washing
(Normal Wash)
Used for normal loads, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly
Q.Wash
Use this mode when washing lightly
soiled clothes for a short time. The
highly recommended laundry
amount is under 2.0kg.
1
1
1
2
3
3
Select the
Q.Wash
program on
the Control
panel.
Add the appropriate
quantity of detergent as
indicated by the water
level next to
Water Detergent.
Or follow the detergent
manufacturer’s
instructions
Add the appropriate
quantity of detergent as
indicated by the water
level next to Water
Detergent.
Or follow the detergent
manufacturer’s
instructions
Select the
Wool
program on
the Control
panel.
Wool Wash
Use this program for washing delicate
fabrics such as lingerie and woolens.
(wash only “water washable” clothes)
Before washing your woolens check
the care label for the washing
instructions.
(wash only water washable clothes)
Use neutral detergent
appropriate for the
laundry.
When washing
woolens use a mild
detergent recommend-
ed for washing wool.
2
2
5
5
4
Soak Wash
Use this mode to wash normal
clothes or thick and heavy clothes
which are excessively dirty.
Soak mode can be used
with Fuzzy program.
1
6
4
3
2
Soak
will not work in
Wool &
Q.Wash
Program.
Keep pressing the PROCESS button until the Soak light is
on and then Wash, Rinse, Spin lights are on simultaneously.
Until the washing process is completed, the Soak light is on
Wash
Rinse
Spin
Soak
Washing Programs
15
Close the lidFinishCaution & Note
Water will be supplied
for 2 minutes after the
start of the wash to
supplement the water
the laundry has
absorbed.
The water level and the
amount of detergent to be
used will be shown and
water will be supplied.
3
5
6
7
7
6
6
4
4
When setting the water level manually, do not
set to Medium to prevent damage to laundry.
Washing with hot water may damage the
laundry (Water is set to cold automatically).
Ensure that the load is under 2kg
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing may
still contain some water. This is normal.
Soak Wash cannot be selected for the
Wool Wash program.
The pulsator rotates for 8
seconds to detect the
laundry load.
Then the water level and
the amount of detergent to
be used will be shown and
water will be supplied.
When the wash
program ends, the
buzzer will ring for
10 seconds before
the Power goes off
automatically.
If water is already in the tub, or putting wet
laundry into the tub before starting will
increase the water level.
With lightweight bulky loads, water level can
be set low.
Changes to water temperature (hot/cold) and
wash level are possible during operation.
(refer to page 12)
8
7
5
16
elay Start (Reservation) Wash
Delay Start (Reservation) Wash is used to delay the finishing time of the operation.
D
The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time , not the start time.
Press the ON/OFF button to turn power on.
1
Additional Function Options
Press the PROGRAM button to select the washing program.
2
• Select the program for laundry on the Control panel.
This method will not work in Wool Program.
3
Press the DELAY START (RESERVATION) button to set the time when
the delayed washing is to be completed.
How to set delay time.
Example :
to finish at 9p.m. set the time as in the figure below.
When you put the button the reservation time changes
If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.
To select washing program, spinning time, , press DELAY START (RESERVATION)
button and select the desired option. Then press the START/PAUSE button.
When the laundry cannot be take out immediately after the wash program ends, it is better to omit
the spinning program(The laundry will be wrinkled if left for a long time after spinning.)
The appropriate quantity of Detergent marked next
to the water level of WATER . DETERGENT.
When the lid is opened, the machine will not operate,
and an alarm signal will remind you to close the lid.
When you press the START/PAUSE button, the light
will blink.
• Water will be supplied for 2 minutes after the start of the
wash to supplement the water the laundry has absorbed.
The washing will be finished according to the delayed time.
•
water level
17
ption Washing
O
When you only need the Wash, Wash/Rinse, Rinse, Rinse/Spin or Spin cycle, this can
be set manually as follows.
Press the PROCESS button until above Option Washing
light is on.
When you want to only drain, wait until the water in the
washing tub drains completely and then, turn off the power.
Press the WATER LEVEL button, to control the water level according to the
amount of laundry. If you do not choose anything, it is set the Large water
level automatically.
(refer to page 13)
(refer to page 12)
Additional Function Options
4
Add the laundry into the washing tub.
5
Press the START/PAUSE button.
Add the detergent and close the lid.
6
Note
• When a Wash, Wash/Rinse or Rinse only option is selected, the water will not be drained off after the wash
is completed.SPIN button and wait until the water in the tub has drained If you wish to drain the water, press the
completely.
• If you do not specify the water level, then Medium will be automatically selected.
• If only Rinse is selected, the process will start from Water Supply.
18
ption Washing
O
“AIR DRY” can be selected by pressing the “PROGRAM” button.
AIR DRY
Press the ON/OFF button to turn power on.
1
Additional Function Options
Press the PROGRAM button until above AIR DRY light is on.
2
3
Press the START/PAUSE button.
Closed the lid.
4
Note
Select “Air Dry”30 min -> Tub Dry
- Use this mode to keep inner tub from getting moldy caused by remaining moisture.
- Do not place any laundry inside tub.
- Use this mode once a week.
Caution) for better performance, put drain hose down to the floor so that water inside will be
completely drained out.
This cause is used to air dry of your laundry and tub dry
The time changes as following order :
•
30min -> 60min -> 2hour -> 3hour
Select “Air Dry” above 1 hour
- Use this mode to reduce the drying time by minimizing remaining moisture on the laundry.
- In general, this is very effective on synthetic items (100% polyester).
- Do place laundry which is evenly distributed (Under 2.0kg).
- For normal clothes: Select 1 hour
- For synthetic items (100% polyester): Select 2 hours or 3 hours (on some models)
19
ther Useful Functions
O
Tub Clean Fucntion
If scrud is allowed to build-up in the machine, it can result in stains on your
clothes or unpleasant smell in your washer.
Scrud is the way build-up that can occur within any washer when the fabric
softener comes into contact with Detergent, and according to particular degree of
dirtiness or quality of water to be use, in these case, use this program to clean
inner tub and outer tub.
Press the ON/OFF button to turn power on.
1
Press both the DELAY START button and the WATER LEVEL button simultaneously.
2
Press the START/PAUSE button.
3
Additional Function Options
The highest WATER LEVEL is set automatically.
After 10 minutes of water supplement, add the oxygenated bleach
4
(about 300 ml).
Do not use Detergent box.
Do not place any laundry inside tub.
Close the lid.
5
Note
Before using this program, remove lint inside lint filter.
When using this program, do not place any laundry inside tub.
This program takes about 2 hours to be completed.
After using this program, remove dirt inside filter.
After finishing this program, open the lid of wash to remove irritant odor.
Do not pour bleach into the tub directly. It might cause damage the tub.
Do not leave diluted oxygenated bleach inside tub for long time.
It rusts the tub must drain the remained diluted oxygenated water out.
Use this program once for every month.
Do not use this program repeatedly.
When the lid is open the machine will not operate,
and an alarm signal will remind you to close the lid.
title
20
ther Useful Functions
O
Additional Function Options
If you want to lock all the keys to prevent settings from being changed by a child, you can use the
child lock option.
Child Lock Function
How to Lock
2
1
3
After all washing conditions are set according to the manual.
Press the ON/OFF button.
Press the START/PAUSE button to start washing.
During the wash program, all the buttons are locked
until washing is completed or until the child- lock
function is deactivated manually.
Press both the PROCESS button and the PROGRAM button simultaneously.
Turn power on.
If you want to use the washing machine without alarm signal sounds, press both the WATER LEVEL and
PROCESS buttons simultaneously.
To make buzzer work, press both the WATER LEVEL and PROCESS buttons simultaneously one more
time.
If you want to unlock during wash, press both the PROCESS and the PROGRAM button simultaneously
again.
Mute Option
How to Unlock
In Child-Lock mode, all Program light will blink.
Note
Introduction
P
lacing and Leveling
21
Installation
Caution
Top view of the machine
more than 10 cm
more
than
2 cm
more than
2 cm
Place the machine on a flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
installation.
At the rear, a minimum clearance of 10 cm is
suggested.
Check that the machine is level
Open the lid and look from above to see if it is
same as shown.
SETTING SCREW
Anti-Rat Cover
U P
BACK
Adjustable legs
Leveling the machine
Lift the front of the washing machine and twist
the Adjustable Leg until the washing machine is
placed evenly.
Installing the Anti-Rat Cover (option) Insert the anti-rat cover to be firmly fixed
from the back or front of washing machine and screw it (1pcs)
If the power is supplied from a cord extension set or generator, the cord extension set or electrical
portable outlet device should be positioned so that it is not exposed to splashing or ingress of moisture.
1
2
3
Please ensure that transit restraint has been removed before operating your machine.
Caution
If the washer is installed on a uneven,weak or tilted floor causing excessive vibration,
spin failure error can happen to it.
It must be placed on a firm and level floor to prevent spin failure.
Loading...
+ 47 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.