LG WD-9080CH Owner's Manual

Spin

Tmp

WD 9080 CH

Part 6:

Part 4:

CONTENTS

Part 1:

Part 5:

Program selection and washing operations.

Steps before operating Fullautomatic

Care and Maintanence.

Part 2:

Washing Machine and safety precautions.

Helpful tips on stain removal

Part 7:

Before calling service.

Part 3:

Technical features.

Determining location and installation

We wish that this product, manufactured at modern facilities with total quality notions, will deliver

Dear Customer,

and keep it for your future reference.

you the best performance. In order to guarantee this, please read this instruction manual thoroughly

www.lge.co.kr

This does not cause any damage to your product.

may be some water left over in your machine.

Due to the quality control processes during production, there

Steps before operating Fullautomatic

Washing Machine and safety precautions

Make sure the Power switch is in the off position and always allow one to two minutes

for the door safety lock to release the lock. Pull the handle to open the door.

Part 1:

The current requirement in order for safe operation of this machine is 16 Ampheres. You will need to have a certified

Your washing machine is set to 220-230 Volts.

electrician to connect a 16 Amp fuse, if there is not enough current load.

Do not forget to check the grounding in all cases of use with or without the transformer. Our company will not be responsible

for any damages caused by operations without grounding.

In order to bring the machine to ready before use, please call your service technician or a certified plummer.

The performance of the washing machine depends on the effectiveness of the cleaning agent. Stains can be permanent if

before washing them in the machine.

low quality detergents are used. Please take necessary effort to clean the stained clothes as described in following pages

To open the front door

60 kg.

54 cm.

60 cm.

85 cm.

5 kg. (11.1 lbs)

10 A.

300 Watts.

50 rpm.

1900 Watts.

800 rpm.

220-230 V, 50 Hz.

Height

Capacity (dry fabric)

Selection Buttons

Depth

Net weight

Width

Handle

Power requirement

Nominal current

Motor power

Heater power

Max. Spin speed

Washing speed

Technical features

Control panel

Part 2:

Program Dial

Top lid

Kick plate cover

Kick plate

Front door

Detergent dispenser

the protective bag and

be placed in the safety bolt

designated as "P", should

holes according to the

Plastic plugs, supplied inside

direction shown.

and rubber bushes by pulling

Remove transport safety bolts

up liquid should ease removal.)

outwards. (A up/down action

and a small squirt of washing

Determining location and installation

"C", should be turned in

until the bolt can be

a anti clockwise direction

partially withdrawn.

Part 3:

Please keep the safety bolts for future transportationand reinstate them before transporting your machine.

Never transport your machine without the transport bolts in position.

Never place your machine on a carpet. This prevents air circulation. The electrical components of the

Attention!

machine may overheat and may cause damage.

The transport safety bolts must be

"C".

removed before any operation of

the machine. Bolt heads, marked

1. Removing transport safety bolts at the rear of the machine

COLD

HOT

Connect the cold water using the hose with blue printing and connect the hot water using the hose with red printing.

until the machine is leveled perfectly. After positioning, tighten the counternut for

is unstable, loosen the plastic counternut and screw or unscrew the adjustable foot

and leveled on its feet. Your machine comes with two adjustable feet. If the machine

2. Feet adjustment

In order for quiet and stable operation, the machine should be placed properly

stability.

3. Water connections

Cold water supply

a) Water inlet hose

To prevent water leaks sealing washers are supplied with the water inlet hose inside the machine, place

more than 8 liters per minute flow rate at fully open tap.)

For proper operation, the pressure of water should be between 1 and 10 atm. (1 atm corresponds to

these on each of the hose ends and tighten both ends fully.

In order to prevent any water leak damages, keep the water taps closed when not in use. Connect the

Hot water supply (only for hot and cold water inlet machines)

cornered end of the hose to the machine water inlet.

normally be suitable. Open outlet gas or electric water heaters must not be used. Multipoint water heaters

boilers operation instructions or supplier.)

or combination boilers may be suitable if they are designed to supply washing machines. (Check your

Pressure: 1-10 bar Temperature: 60°C max. A hot water supply fed from a separate cold water tank will

+ 13 hidden pages