![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg1.png)
OWNER’S MANUAL
WASHING MACHINE
WD3250HSA
WD3250HWA
MFL48165996
www.lg.com
Before beginning installation, read these instructions carefully. This will simplify
installation and ensure that the washer is installed correctly and safely.
Leave these instructions near the washer after installation for future reference.
ENGLISH
ESPAÑOL
MFL48165996_E.indd 1 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg2.png)
2
TABLE OF CONTENTS
TABLE OF CONTENTS
3 PRODUCT FEATURES
4 IMPORTANT SAFETY INSTRUCTIONS
4 BASIC SAFETY PRECAUTIONS
5 GROUNDING INSTRUCTIONS
6 SAFETY INSTRUCTIONS FOR INSTALLATION
7 SAFETY INSTRUCTIONS FOR USE, CARE,
CLEANING, AND DISPOSAL
8
INTRODUCING YOUR WASHING MACHINE
8 Parts and Accessories
9 Control panel features
11 INSTALLATION INSTRUCTIONS
11 Preview installation order
12 Checking and choosing the proper location
13 Unpacking and removing shipping bolts
14 Connecting the water lines
15 Connecting the drain line
16 Leveling the washing machine
17 Plugging in the power cord and grounding
17 Test run
18 PREPARATION
18 Sorting wash loads
18 - Precautions for fabric care before wash cycle
19 - Fabric care labels
19 - Sorting laundry
20 Using detergent/fabric softener
20 - Recommended detergent
20 - Loading the dispenser
22 USING YOUR WASHING MACHINE
22 Basic operation
23 Cycle guide
24 Main cycle
24 - Reduce laundry allergen, ALLERGIENE
™
24 - Reduce laundry bacteria,
SANITARY
24 - Blankets or bulky items, BULKY/LARGE
24 - Normal items, COTTON/NORMAL
24 - Wrinkle free items,
PERM. PRESS
24 - Sheer items,
DELICATES
24 - Items labeled wool or hand-washable,
HAND
WASH/WOOL
24 - Quick wash, SPEED WASH
25 Cycle setting buttons
25 Setting options before cycle
25 - Setting the water temperature, WASH TEMP.
25 - Setting spin speed, SPIN SPEED
25 - Setting soil level of laundry, SOIL LEVEL
26 - Set the drying time, Dry
27 - Prewashing, PRE-WASH
27 - Adding extra rinse cycle, EXTRA RINSE
27 - Presetting the start time, DELAY WASH
27 - Efficiency cleaning, STEAM
27 - Saving time, TURBOWASH™
28 Setting options during cycle
28 - Button lock feature, CHILD LOCK
29 MAINTENANCE
29 Care
29 - Care after wash
29 - Care in cold climates
30 Cleaning
30 - Clean your the drum, TUB CLEAN
31 - Cleaning the detergent dispenser drawer
31 - Cleaning the water inlet filters
32 - Cleaning the drain pump filter
33 - Cleaning the door seal
34 TROUBLESHOOTING
34 Checking error messages
35 Before calling for service
36 SPECIFICATIONS
37 USING SMARTDIAGNOSIS™
MFL48165996_E.indd 2 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg3.png)
3
ENGLISH
PRODUCT FEATURES
PRODUCT FEATURES
INVERTER DIRECT-DRIVE MOTOR
The inverter motor, which is directly connected to the tub, minimizes energy loss and produces little noise
and vibration.
SMARTDIAGNOSIS™
Should you experience any technical difficulty with your washing machine, it has the capability of
transmitting data by phone to the Customer Information Center. The call center agent records the data
transmitted from your machine and uses it to analyze the issue, providing a fast and effective diagnosis (Refer
to page
3
7).
TUB CLEAN
Regular cleaning of the tub on a monthly basis using TUB CLEAN can help keep the tub clean and fresh.
MAGNETIC DOOR PLUNGER
Safely and conveniently secure the door slightly ajar with the magnetic door plunger. This will promote
air circulation and allow the interior of the machine to dry. To use this feature, after the load has been
removed, do not close the door completely.
When the magnetic door plunger comes into contact with the metal washer cabinet, it will secure the door
slightly open allowing the interior of the washer to dry.
LARGE CAPACITY STAINLESS STEEL DRUM
The large capacity stainless steel drum offers extreme durability and is tilted to improve efficiency and allow
easier access for large items.
CHILD LOCK
Use this option to disable the controls during a wash cycle. This option can prevent children from changing
cycles or operating the machine.
DETERGENT DISPENSER DRAWER
The four-compartment dispenser drawer makes it easy to separate the pre-wash detergent, the main
laundry detergent, liquid bleach, and fabric softener into different compartments.
HIGH-EFFICIENCY STEAM CYCLES
During LG’s unique high-efficiency STEAM cycles, with hot steam a gently removes tough stains.
MFL48165996_E.indd 3 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg4.png)
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
Your Safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION.
These words mean:
DANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
WARNING
You can be killed or seriously injured if you don’t follow instructions.
CAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what can happen if the instructions are not followed.
BASIC SAFETY PRECAUTIONS
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic
precautions, including the following.
• Use this appliance only for its intended purpose as described
in this owner’s Manual.
• Before use, the washer must be properly installed as
described in this manual.
• Do not wash articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry cleaning
solvents, or other flammable or explosive substances, as
they give off vapors that could ignite or explode.
• Do not add gasoline, dry cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
• Under certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for 2 weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using
the washer, turn on all hot water faucets and let the water
flow from each for several minutes. This will release any
accumulated hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
• Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is
used near children.
• Before the washer is removed from service or discarded,
remove the lid to prevent children from climbing inside.
• Do not install or store the washer where it will be exposed
to the weather or freezing temperatures.
• Do not tamper with controls.
• Keep the area underneath and around your appliances free of
combustible materials (lint, paper, rags, etc.), gasoline,
chemicals and other flammable vapors and liquids.
• Do not repair or replace any part of the washer or attempt
any servicing other than as described in this manual. We
strongly recommend that any service be performed by a
qualified technician.
• See Installation Instructions for grounding requirements.
• ALWAYS follow the fabric care instructions supplied by the
garment manufacturer.
• Do not place items exposed to cooking oil in your washer.
Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire.
• Use fabric softeners or products to eliminate static only as
recommended by the manufacturer.
• This washer is not designed for maritime use or for mobile
installations such as in RVs, aircraft, etc.
• Turn off the water faucets and unplug the washer if the
machine is to be left for an extended period of time, such as
during vacations.
• Do not use to dry articles containing foam rubber or
similarly textured rubber-like materials.
• Packaging material can be dangerous for children. There is a
risk of suffocation! Keep all packaging from children.
• Always check the inside of the washer for foreign objects
before loading laundry. Keep the lid closed when not in use.
• Do not reach into the appliance if the tub or agitator is
moving.
MFL48165996_E.indd 4 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg5.png)
5
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least resistance for electric current. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be
plugged into an appropriate outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
WARNING
Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with a
qualified electrician or servicer if you are in doubt as to whether the appliance is properly grounded. Do not
modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a
qualified electrician. Failure to follow these warnings can cause serious injury, fire, electric shock, or death.
MFL48165996_E.indd 5 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg6.png)
6
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death
.
SAFETY INSTRUCTIONS FOR INSTALLATION
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic
precautions, including the following.
• Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures. Installation
instructions are packed with the washer for
installer’s reference. If the washer is moved to a
new location, have it checked and reinstalled by a
qualified service technician. Failure to follow this
warning can cause serious injury, fire, electric
shock, or death.
• Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Failure to follow this warning can cause serious
injury, fire, electric shock, or death.
• For personal safety, this appliance must be
properly grounded. Failure to follow this warning
can cause serious injury, fire, electric shock, or
death.
• The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to
minimize the possibility of electric shock from this
appliance.
• This washer must be plugged into a 120 V~,60Hz
grounded outlet. Failure to follow this warning can
cause serious injury, fire, electric shock, or death.
• Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded. Failure to follow this warning
can cause serious injury, fire, electric shock, or
death.
• Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility and
obligation to have it replaced with a properly
grounded 3-prong wall outlet. Failure to follow this
warning can cause serious injury, fire, electric
shock, or death.
• Do not install on carpet. Install washer on a solid
floor. Failure to follow this warning can cause
serious leak damage.
• Do not remove ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong outlet. Failure to follow these warnings
can cause serious injury, fire, electric shock, or
death.
• The washer should always be plugged into its own
individual electrical outlet which has a voltage
rating that matches the rating plate. This provides
the best performance and also prevents
overloading house wiring circuits which could
cause a fire hazard from overheated wires.
• Never unplug your washer by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet. Failure to follow this
warning can cause serious injury, fire, electric
shock, or death.
• Repair or immediately replace all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end. Failure to
follow this warning can cause serious injury, fire,
electric shock, or death.
• When installing or moving the washer, be careful
not to pinch, crush, or damage the power cord.
Failure to follow this warning can cause serious
injury, fire, electric shock, or death.
• The washer must be installed and electrically
grounded by a qualified service person in
accordance with local codes to prevent shock
hazard and assure stability during operation.
• The washer is heavy. Two or more people may be
needed to install and move the appliance. Failure
to do so can result in back or other injury.
• Store and install the washer where it will not be
exposed to temperatures below freezing or
exposed to outdoor weather conditions. Failure to
follow this warning can cause serious leak
damage.
• Do not install the washer in humid spaces to
reduce the risk of electric shock. Failure to follow
this warning can cause serious injury, fire, electric
shock, or death.
• To reduce the risk of injury to persons, adhere to
all industry recommended safety procedures
including the use of long sleeved gloves and safety
glasses. Failure to follow all of the safety warnings
in this manual could result in property damage,
injury to persons or death.
MFL48165996_E.indd 6 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg7.png)
7
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic
precautions, including the following.
SAVE THESE INSTRUCTIONS
• Unplug the washer before cleaning to avoid the
risk of electric shock.
• Never use harsh chemicals, abrasive cleaners, or
solvents to clean the washer. They will damage
the finish.
• Do not put oily or greasy rags or clothing on top of
the washer. These substances give off vapors that
could ignite the materials.
• Do not wash items that are soiled with vegetable
or cooking oil. These items may contain some oil
after laundering. Due to the remaining oil, the
fabric may smoke or catch fire by itself.
• Disconnect this appliance from the power supply
before attempting any user maintenance. Turning
the controls to the OFF position does not
disconnect this appliance from the power supply.
Failure to follow this warning can cause serious
injury, fire, electric shock, or death.
• Do not combine laundry products for use in one
load unless specified on the label.
• Do not mix chlorine bleach with ammonia or acids
such as vinegar. Follow package directions when
using laundry products. Incorrect usage can
produce poisonous gas, resulting in serious injury
or death.
• Do not reach into the washer while parts are
moving. Before loading, unloading, or adding
items, press the START/PAUSE button and allow
the drum to coast to a complete stop before
reaching inside. Failure to follow this warning can
cause serious injury, fire, electric shock, or death.
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. As children
grow, teach them the proper, safe use of all
appliances. Failure to comply with these warnings
could result in serious injury to persons or death.
• Destroy the carton, plastic bag, and other packing
materials after the washer is unpacked. Children
might use them for play. Cartons covered with
rugs, bedspreads, or plastic sheets can become
airtight chambers. Failure to comply with these
warnings could result in serious injury to persons
or death.
• Keep laundry products out of children’s reach. To
prevent injury to persons, observe all warnings on
product labels. Failure to comply with these
warnings could result in serious injury to persons
or death..
• Remove the door to the washing compartment to
avoid the danger of children or small animals
getting trapped inside before your washer is
removed from service or discarded. Failure to do
so can result in serious injury to persons or death.
• This appliance is not intended for use by persons
(including children) with reduced physical,sensory
or mental capabilities, or lack of experience and
knowledge, unless they have beengiven
supervision or instruction concerning use of the
appliance by a person responsible fortheir
safety. Children should be supervised to ensure
that they do not play with the appliance.
MFL48165996_E.indd 7 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg8.png)
8
INTRODUCING YOUR WASHING MACHINE
INTRODUCING YOUR WASHING MACHINE
Parts and Accessories
Parts
Accessories
Hot/cold water hoses Non-skid pads Caps for covering shipping bolt holes
Wrench Tie strap Elbow bracket (for securing drain hose)
Detergent
dispenser
drawer
(See page 20)
Door
Magnet Door
Plunger
(see page 3)
Control panel
(See page 9)
Door
seal
Tub
Leveling
feet
Drain pump filter cover
Drain pump filter
Drain hose
Water inlets
Shipping
bolts
Power cord
Drain hose
Included Accessories
MFL48165996_E.indd 8 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg9.png)
9
ENGLISH
INTRODUCING YOUR WASHING MACHINE
Button Description
y
Turns the washing machine on and off.
y
(During the wash cycle) stops operation, and cancels the settings.
y
TUB CLEAN
- For tub clean (see page 30)
y
ALLERGIENE™
- For cotton, underwear (see page 24)
y
SANITARY
- For underwear, diaper etc. (see page 24)
y
BULKY/LARGE
- For blankets or large bulky items (see page 24)
y
COTTON/NORMAL
- For general laundry, such as cotton T-shirts or towels (see page 24)
y
PERM. PRESS
- For wrinkle-free fabrics (see page 24)
y
DELICATES
- For sheer and delicate fabrics (see page 24)
y
HAND WASH/WOOL
- For wool or hand-wash fabrics (see page 24)
y
SPEED WASH
- For small quantities of lightly soiled items (see page 24)
y
Starts or pauses the washing machine cycle.
- If you do not press the
C
button within 4 minutes of selecting a cycle, the washing
machine will turn off automatically.
y
(Press repeatedly) Selects the water temperature for the wash cycle (see page 25).
- Select water temperature from 5 settings.
y
(Press repeatedly) Selects the spin speed in the desired level (see page 25).
- Selects spin speed from 5 settings.
y
(Press repeatedly) Selects a wash cycle by soil level (see page 25).
- Selects soil level from 5 settings.
y
(Press repeatedly) Select drying cycle, pressing the button DRYING(see page 26)
Control panel features
Operation
Operation
Display
Cycle selector
Soil
Level
Selection
Button
Spin
Speed
Selection
Button
Water
Temperature
Selection
Button
Start/
Pause
Button
Power
Button
MFL48165996_E.indd 9 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bga.png)
10
INTRODUCING YOUR WASHING MACHINE
Display
Operation (continued)
Button Description
y
Set delay time of starting cycle (See page. 26).
y
(Press before wash cycle) Pre-wash heavily soiled laundry (See page.27).
y
(Press and hold during wash cycle) Lock/Unlock the button (See page 28).
y
Add extra rinse cycle to the selected one (See page. 27).
y
(Press before starting wash cycle) Use this option to add steam for extra cleaning
power (See page. 27).
y
Use this option to save time (See page 27).
Display Icon Description
y
This portion of the display shows which stage of the wash cycle is currently
underway (WASH, RINSE, SPIN, DRY).
y
Indicates that the door is locked. The washer door will lock while the washer is
operating. The door can be unlocked by pressing the START/ PAUSE button to stop the
washer.
y
This indicator shows that the washer has been set for DELAY WASH. The washer
will start automatically after the set delay time has passed.
y
When the START/PAUSE button is pressed, the washer automatically detects the wash
load (weight) and optimizes the washing time, based on the selected cycle and options.
The display will then indicate the estimated time remaining for the selected wash cycle.
Door lock
indicator
Estimated time remaining/
error message display
(See page 34)
Cycle
process
indicator
Delay
wash
indicator
MFL48165996_E.indd 10 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bgb.png)
11
ENGLISH
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Preview installation order
WARNING
y
Washer is heavy! Two or more people are required when moving and unpacking the washer.
Failure
to do so can result in back or other injury.
y
Store and install the washer where it will not be exposed to temperatures below freezing or exposed
to outdoor weather conditions.
Failure to follow this warning can cause serious injury, fire, electric
shock, or death.
y
Properly ground washer to conform with all governing codes and ordinances.
Failure to follow this
warning can cause serious injury, fire, electric shock, or death.
y
To reduce the risk of electric shock, do not install the washer in humid spaces.
Failure to follow this
warning can cause serious injury, fire, electric shock, or death.
y
The base opening must not be obstructed by carpeting when the washer is installed on a carpeted floor.
y
Do not remove ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong
outlet.
Failure to follow this warning can cause serious injury, fire, electric shock, or death.
Checking and choosing the
proper location
Unpacking and removing
shipping bolts
Connecting the water line
Connecting the drain line
Leveling the washing
machine
Plugging in the power cord
and grounding
Test run
MFL48165996_E.indd 11 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bgc.png)
12
INSTALLATION INSTRUCTIONS
Checking and choosing the proper
location
Install the washing machine on a solid floor that
is strong and rigid enough to support the weight
of the washing machine, even when fully loaded,
without flexing or bouncing. If the floor has too
much flex, you may need to reinforce it to make
it more rigid. If the floor is not solid, it may cause
severe vibration and noise.
1 Clean the floor before installation.
- Make sure to select solid and smooth ground.
2 Two or more people are needed for moving and
unpacking the washing machine.
3 Allow for sufficient space between the walls
and the washing machine for installation.
Space requirements
You must allow sufficient space for water lines, the
drain line, and airflow.
NOTE
y
Be sure to allow for wall, door, or floor moldings
that may increase the required clearances.
Installing on a floor
29
3
/4"
(75.6 cm)
4"
(10 cm)
51"
(129.5 cm)
22
1
/4"
(57 cm)
27"
68.6 cm
1"
(2.5 cm)
1"
NOTE
y
The floor must be strong and rigid enough to
support the weight of the washer, when fully
loaded, without flexing or bouncing. If your floor
has too much flex, you may need to reinforce it
to make it more rigid.
A floor that is adequate for a top-loading washer
may not be rigid enough for a front loading
washer, due to the difference in the spin speed
and direction. If the floor is not solid, your
washer may vibrate and you may hear and feel
the vibration throughout your house.
y
Before installing the washer, make sure the floor
is clean, dry and free of dust, dirt, water and oils
so the washer feet can not slide easily. Leveling
feet that can move or slide on the floor can
contribute to excess vibration and noise due to
poor contact with the floor.
y
If a drip pan must be used, take extra care to
follow the instructions provided with the drip pan
and make sure the leveling feet are adjusted for
firm and even contact with the pan. Use of drip
pans and failure to properly level the machine
may result in increased vibration and noise during
operation.
MFL48165996_E.indd 12 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bgd.png)
13
ENGLISH
INSTALLATION INSTRUCTIONS
Unpacking and removing shipping bolts
When removing the washer from the carton base,
be sure to remove the foam drum support in the
middle of the carton base.
If you must lay the washer down to remove the
base packaging materials, always lay it carefully on
its side.
Do NOT lay the washer on its front or back.
1
Remove the bottom two shipping bolts with
the wrench (included) to fully loosen all four
shipping bolts by turning them counterclockwise
and then pulling them out.
Shipping
bolt
Retainer
2
Locate the four hole caps included in the
accessory pack and install them in the shipping
bolt holes.
Cap
NOTE
y
Save the bolt assemblies for future use. To
prevent damage to internal components, DO
NOT transport the washer without reinstalling
the shipping bolts.
y
Failure to remove shipping bolts and retainers
may cause severe vibration and noise, which
can lead to permanent damage to the washer.
The cord is secured to the back of the washer
with a shipping bolt to help prevent operation
with shipping bolts in place.
MFL48165996_E.indd 13 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bge.png)
14
INSTALLATION INSTRUCTIONS
Connecting the water lines
1
Check the rubber seals on both sides of the
hose.
- Insert a rubber seal into the threaded fittings
on each hose to prevent leaking.
Rubber seal
Water hose
(To water inlet on the
washing machine)
Rubber seal
Water hose
(To faucet)
2
Connect the water supply hoses to the HOT and
COLD water faucets tightly by hand and then
tighten another 2/3 turn with pliers.
- Connect the blue hose to a cold water faucet
and the red hose to a hot water faucet.
WARNING
y
Do not overtighten.
Damage to the coupling
can result.
3
After connecting inlet hose to water faucets,
turn on the water faucets to flush out foreign
substances (dirt, sand or sawdust) in the water
lines. Let water drain into a bucket, and check
the water temperature.
4
Connect the hoses to the water inlets tightly
by hand and then tighten another 2/3 turn with
pliers.
- Connect the blue hose to the cold water inlet
and the red hose to the hot water inlet.
Cold
water
inlet
Hot water
inlet
WARNING
y
Do not overtighten the hoses.
Overtightening
can damage the valves resulting in leaking and
property damage.
5
Check for leaks by turning on the faucets.
- If water leaks, check steps 1 to 4 again.
NOTE
y
For your safety, and for extended product
life, use only authorized components. The
manufacturer is not responsible for product
malfunction or accidents caused by the use of
separately purchased unauthorized parts.
y
Use new hoses when you install the washing
machine. Do not reuse old hoses. Use only the
inlet hoses provided with the washer. LG does
not recommend the use of aftermarket hoses.
y
Periodically check the hoses for cracks, leaks
and wear, and replace the hoses every 5 years.
y
Do not stretch the water hoses intentionally,
and make sure that they are not crushed by
other objects.
y
Water supply pressure must be between
14.5 PSI and 145 PSI (100~1000 kPa). If the
water supply pressure is more than 116 PSI, a
pressure reducing valve must be installed.
y
To provide optimum washing performance the
hot water temperature should be set at 120-
135°F (48-57°C) and the cold at 60°F (15°C).
MFL48165996_E.indd 14 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bgf.png)
15
ENGLISH
INSTALLATION INSTRUCTIONS
Connecting the drain line
Secure the drain hose in place to prevent moving
and leaking.
NOTE
y
The drain hose should be properly secured.
Failure to properly secure the drain hose can
result in flooding and malfunction.
y
Total height of the house end should not
exceed 96 inches (2.44 m) from the bottom of
the washer.
y
The drain must be installed in accordance with
any applicable local codes and regulations.
y
Make sure that the water lines are not
stretched, pinched, crushed, or kinked.
Using a standpipe
1
Clip the end of the hose into the elbow bracket.
- Connect the elbow bracket within 4 inches (10
cm) from the end of the drain hose. If the drain
hose is extended more than 4 inches (10 cm)
beyond the end of the elbow bracket, mold or
microorganisms could spread to the inside of
the washer.
No more than
4 inches (10 cm)
Elbow bracket
2
Insert the end of the drain hose into the
standpipe.
Drain Hose
Elbow Bracket
3
Use a tie strap to secure the drain hose in place.
Using a laundry tub
1
Clip the end of the hose into the elbow bracket.
- Connect the elbow bracket within 4 inches (10
cm) from the end of the drain hose. If the drain
hose is extended more than 4 inches (10 cm)
beyond the end of the elbow bracket, mold, or
microorganisms could spread to the inside of
the washer.
No more than
4 inches (10 cm)
Elbow bracket
2
Hang the end of the drain hose over the side of
the laundry tub.
Elbow Bracket
Drain Hose
3
Use a tie strap to secure the drain hose in place.
MFL48165996_E.indd 15 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg10.png)
16
INSTALLATION INSTRUCTIONS
Leveling the washing machine
The washer tub of your new washing machine
spins at very high speeds. To minimize vibration,
noise, and unwanted movement, the floor must be
perfectly level and solid.
1
Check the washing machine’s level.
- Check the precise level by rocking the top
edges of the washing machine or placing
a level on the washing machine. The slope
beneath the washing machine must not exceed
1°, and all four leveling feet must rest firmly on
the floor.
Level
1°
2
Turn the lower leveling feet clockwise to level
the washing machine.
- Turning the lower leveling feet clockwise raises
the washing machine.
Raise
3
Turn the locknuts counterclockwise and tighten
them when the washing machine is level.
Tighten all 4 lock
nuts securely using
the wrench.
4
Check the washing machine’s level again.
- Push or rock the top edges of the washing
machine gently to make sure that the washing
machine does not rock.
- If the washing machine rocks, repeat steps 1
to 3.
WARNING
y
Using the washing machine without leveling,
it may result in malfunction caused by the
production of excess vibration and noise.
y
If you are installing the washing machine
on the optional pedestal, you must adjust
the leveling feet on the pedestal to level the
washing machine. The washing machine´s
leveling feet should be minimized and turn the
locknuts counterclockwise to secure.
y
Use the leveling feet only when you level the
washing machine.
If you raise the leveling feet
unnecessarily, it may cause abnormal vibration
of the washing machine.
Using non-skid pads (optional)
If you install the washing machine on a slippery
surface, it may move because of excessive
vibration. Incorrect leveling may cause malfunction
through noise and vibration. In the event of this, lay
the non-skid pads under the leveling feet and adjust
the level.
1
Clean the floor to attach the non-skid pads.
- Use a dry rag to remove and clean foreign
objects or moisture. If moisture remains, the
non-skid pads may slip.
2
Adjust the level after placing the washing
machine in the installation area.
3
Place the adhesive side of the non-skid pad on
the floor.
- It is most effective to install the non-skid pads
under the front legs. If it is hard to place the
pads under the front legs, place them under
the back legs.
Remove
backing
This side up
Adhesive
side
4
Check the washing machine’s level again.
- Push or rock the top edges of the washing
machine gently to make sure that the washing
machine does not rock. If the washing machine
rocks, level the washing machine again.
MFL48165996_E.indd 16 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg11.png)
17
ENGLISH
INSTALLATION INSTRUCTIONS
Plugging in the power cord and
grounding
Make sure to ground the washing machine to
prevent a short circuit or an electric shock when
plugging in.
Using a 3-prong outlet
Plug in the electrical outlet without additional
grounding.
WARNING
y
The power outlet must be within 60 inches (1.5 m)
of either side of the washer.
y
The appliance and outlet must be positioned so that
the plug is easily accessible.
y
Do not overload the outlet with more than one
appliance.
y
The outlet must be grounded in accordance with
current wiring codes and regulations.
y
Time-delay fuse or circuit breaker is recommended.
y
It is the personal responsibility and obligation of the
product owner to have a proper outlet installed by a
qualified electrician.
y
Do not use a worn or damaged power cord or
power plug. Replace or repair it immediately.
Failure to do so may result in death, fire, electric
shock, or malfunction.
y
Do not modify the power cord and take care not to
damage it when installing or moving the washing
machine.
Failure to do so may result in death, fire,
electric shock, or malfunction.
y
Make sure that the washing machine is grounded.
y
Connect this washing machine to a grounded outlet
conforming to the rating prior to use.
Failure to do
so may result in fire, electric shock, or malfunction.
y
Do not use adaptors or extension cords.
The
washing machine should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the rating plate. Failure to do so
may result in fire, electric shock or disorder.
y
Do not damage or cut off the ground prong of
the power cord.
Doing so may cause death, fire,
electric shock, or product malfunction.
Test run
Check if the washing machine is properly installed
and run a test cycle.
1
Load the washing machine with 6 pounds of
laundry.
2
Press
A
and turn
B
on the right
3
Press after then press
4
Press
C
.
- The wash cycle starts.
5
Check if water is supplied, that the washing
machine does not rock or vibrates excessively,
and that it drains well during the spin cycle.
- If water leaks during water supply, see page
14,
Connecting the water lines
to connect
them properly.
- If the washing machine rocks and vibrates
excessively, see page 16,
Leveling the washing
machine
to level it again.
- If the drain does not work, see page 15,
Connecting the drain line
to install it properly.
MFL48165996_E.indd 17 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg12.png)
18
PREPARATION
u Check all pockets to make sure that they are
empty.
- Items such as clips, matches, pens, coins, and
keys can damage both your washer and your
clothes.
u Close zippers, hooks, and drawstrings to prevent
these items from snagging or tangling on other
clothes.
u Pretreat heavily stained areas before washing.
- Doing so will produce clean, stain-free results.
u Combine large and small items in a load. Load
large items first.
u Large items should not be more than half of the
total washload.
u The washer can be fully loaded, but the drum
should not be tightly packed with items.
-The door of the washer should close easily.
u Do not wash single items, except for bulky items
such as blankets. Make sure to wash laundry in
similar types of loads.
- Washing a single small item may result in the tub
becoming unbalanced, vibrating and making a
noise.
u Do not wash waterproof clothes.
- This may cause abnormal vibration, or may cause
the load to bounce, which could damage the tub.
u Check if there are any other foreign objects in the
door seal and take extra care that clothes do not
get caught there.
- Foreign objects in the door seal may stain
clothes, and water may leak if clothes get caught
in the door seal.
u Wash underwear or small, light items in a laundry
net.
- Small, light items may get caught in the door
seal, and a brassiere hook may damage other
items or the tub.
u Brush heavy soil, dust, or hair off fabrics before
washing.
- Laundry may not wash clean if there is dirt or
sand on the fabrics, or they may damage due to
particles rubbing against sheer fabrics.
u Wash blankets individually.
- Washing more than one blanket together may
produce unclean results due to tangling or an
unbalanced load.
u Always separate fabrics according to their colors
and wash them separately to prevent colors from
running.
- Fabrics may damage or become stained due to
fabric dyes running, or due to foreign objects
transferring from one fabric to another.
PREPARATION
Sorting wash loads
Precautions for fabric care before wash cycle
Read and observe the following to prevent shrinkage or damage to clothes.
MFL48165996_E.indd 18 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg13.png)
19
ENGLISH
PREPARATION
Category Label Directions
Washing
Hand Wash
Machine Wash, Normal
Cycle
Use Permanent Press/
Wrinkle Resistant washing
machine setting (which
has a cool down or
cold spray before the
reduced spin)
Use Gentle/Delicate
washing machine setting
(slow agitation and/ or
reduced wash time).
Do Not Wash
Do Not Wring
Water
Temperature
Hot
Warm
Cold/Cool
Bleach symbols
Any Bleach (When
Needed)
Only Non-Chlorine Bleach
(When Needed)
Do Not Bleach
Colors
Whites / Lights / Darks
Soil
Heavy / Normal / Light
Fabric
Delicates / Easy Care / Sturdy
Cottons
Lint
Lint Producers / Lint Collectors
Fabric care labels
Most articles of clothing feature fabric care labels
that include instructions for proper care.
Sorting laundry
It is recommended that you sort laundry into similar
loads that are washable in the same cycle.
Refer to the following chart for sorting clothes
MFL48165996_E.indd 19 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg14.png)
20
PREPARATION
Loading the dispenser
The detergent dispenser drawer of the washing
machine has a dispenser compartment for each
detergent type. Add the appropriate detergents
into its respective compartments.
1
Pull out the detergent dispenser drawer.
2
Add the appropriate detergent to its allocated
compartment.
- If you use a liquid detergent, check if the liquid
detergent cup is in place.
- If you use a powdered detergent, remove the
liquid detergent cup and put the powder in the
main wash detergent compartment.
Liquid chlorine
bleach
compartment
Liquid
detergent
Cup
Main wash
detergent
compartment
Pre-wash
detergent
compartment
Liquid fabric
softener
compartment
3
Close the detergent dispenser drawer slowly.
- Slamming the detergent dispenser drawer may
result in the detergent overflowing into another
compartment or pouring into the tub earlier
than programmed.
NOTE
y
It is normal for a small amount of water to
remain in the dispenser compartments at the
end of the cycle.
Using detergent/fabric softener
Recommended detergent
Low sudsing detergent is recommended for this
washer. Use the manufacturer's recommended
amount.
If low sudsing detergent is not available, a reduced
amount of regular detergent may be used.
Because reducing the amount of detergent may
reduce cleaning, it is important to pretreat stains,
sort carefully by color and soil level, and avoid
overloading.
Detergent usage may need to be adjusted for
water temperature, water hardness, size and soil
level of the load.
For best results, avoid using too much detergent.
NOTE
y
Use less detergent for soft water.
y
Wipe up any spills immediately, as liquids
could damage the finish and the control panel
of the washing machine.
y
Using too much detergent can cause a build-
up in the tub resulting in unsatisfactory
performance and machine malfunction.
y
If you use a detergent that does not dissolve
easily or a detergent with high viscosity, it
will leave a residue on the tub, which may not
rinse properly.
MFL48165996_E.indd 20 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg15.png)
21
ENGLISH
PREPARATION
Liquid Bleach Compartment
This compartment holds liquid chlorine bleach,
which will be dispensed automatically at the proper
time during the wash cycle.
NOTE
y
Do not add powdered or liquid color-safe
bleach to this compartment.
y
Always follow the manufacturer’s
recommendations when adding bleach. Do not
exceed the maximum fill line. Using too much
bleach can damage fabrics.
y
Never pour undiluted liquid chlorine bleach
directly onto the load or into the drum. Fabric
damage can occur.
Fabric Softener Compartment
This compartment holds liquid fabric softener,
which will be automatically dispensed during the
final rinse cycle.
NOTE
y
Always follow the manufacturer’s
recommendations when adding fabric
softener. Do not exceed the maximum fill line.
Using too much fabric softener may result in
stained clothes.
y
Dilute concentrated fabric softeners with
warm water. Do not exceed the maximum fill
line.
y
Never pour fabric softener directly onto the
load or into the drum.
Pre-wash Detergent Compartment
Add liquid or powdered detergent to this
compartment when using the pre-wash option.
NOTE
y
If liquid detergent is to be used for the main
wash when using the pre-wash option, the
liquid detergent cup accessory must be used
in main wash dispenser to prevent the main
wash liquid detergent from being dispensed
immediately.
y
The amount of detergent added for the pre-
wash option is 1⁄2 the amount recommended
for the main wash cycle. For example, if the
main wash cycle requires one measure of
detergent, add 1⁄2 measure for the pre-wash
option.
Main Wash Detergent Compartment
This compartment holds laundry detergent for the
main wash cycle, which is added to the load at the
beginning of the cycle.
Never exceed the manufacturer’s
recommendations when adding detergent. Using
too much detergent can result in detergent buildup
in clothing and the washer. Either powdered or
liquid detergent may be used.
NOTE
y
Liquid or powdered color-safe bleach may be
added to the main wash compartment with
detergent of the same type.
y
When using liquid detergent, make sure the
liquid detergent cup and insert are in place. Do
not exceed the maximum fill line.
y
When using powdered detergent, remove
the insert and liquid detergent cup from the
compartment. Powdered detergent will not
dispense with the liquid detergent cup and
insert in place.
MFL48165996_E.indd 21 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg16.png)
22
USING YOUR WASHING MACHINE
USING YOUR WASHING MACHINE
Basic operation
Load the laundry into the washing machine and close the door.
1
2
3
4
5
6
Press
A
.
- The lights around the cycle selector knob will illuminate and a chime will sound.
Turn
B
to the desired cycle.
- The proper default option is automatically set according to the wash cycle. See
page 23,
Cycle guide
, for more detailed default options for each cycle.
- See page 24,
Main cycle
, for details on the wash cycles.
- To change the options, press the option button and select the desired option.
See page 25,
Setting options before cycle
, for more details on options.
- Skip to step 4 to use the default setting without changing the options.
Add the proper amount of detergent and additions (bleach, softener) into the
detergent dispenser drawer.
- See page 20,
Using detergent/fabric softener
, for more details on using
detergent.
Press
C
.
- The washing machine will start.
When the melody plays, the wash cycle is finished.
- When the washing cycle is finished, the door will unlock. Open the door and
remove the laundry immediately.
- Make sure to check around the door seal when taking out the finished load.
Small items may be caught in the door seal.
NOTE
y
The front-load washing machine rotates the laundry in a way that allows it to use less water while still
fully saturating your clothing. It is normal to not be able to see water during the wash cycle.
y
If the temperature or the water level inside the machine is too high, the door locks and cannot be
opened. To open the door while washing, use the Rinse + SPIN feature.
WARNING
y
To reduce the risk of fire, electric shock, or injury to persons,
read the IMPORTANT SAFETY
INSTRUCTIONS before operating this appliance.
MFL48165996_E.indd 22 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg17.png)
23
ENGLISH
USING YOUR WASHING MACHINE
Cycle guide
The cycle guide below shows the options and recommended fabric types for each cycle.
●
= Available option
- Cycle time depends on water pressure, type and amount of load and chosen additional options.
- To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle.
RECOMMENDED LOADS
CYCLE FABRIC TYPE
DISPLAY
TIME(MIN)
BASIC OPTION (
=DEFAULT) ADDITIONAL OPTIONS
Maximum
Load
WASH
TEMP.
SPIN
SPEED
SOIL
LEVEL
PRE-
WASH
EXTRA
RINSE
STEAM
Turbowash™
Dry
TUB CLEAN This cycle is designed
to remove a mildewy
69
-
ALLERGIENE™
Cotton, underwear,
pillow covers,
bed sheets, baby
wear
109 ~ 112
EXTRA HIGH
HIGH
MEDIUM
LOW
NO SPIN
Less
than
8.0 kg
SANITARY Heavily soiled
underwear, work
clothes, diapers, etc.
98 ~ 107
EXTRA HOT
EXTRA HIGH
HIGH
MEDIUM
LOW
NO SPIN
HEAVY
NORMAL
LIGHT
Less
than
8.0 kg
BULKY/
LARGE
Large items such
as blankets and
comforters
56 HOT
WARM
COLD
TAP COLD
MEDIUM
LOW
NO SPIN
HEAVY
NORMAL
LIGHT
Less
than
8.0 kg
COTTON/
NORMAL
Cotton, linen, towels,
shirts, sheets, jeans,
mixed loads
50 ~ 71
EXTRA HOT
HOT
WARM
COLD
TAP COLD
EXTRA HIGH
HIGH
MEDIUM
LOW
NO SPIN
HEAVY
NORMAL
LIGHT
Less
than
18.0 kg
PERM.
PRESS
Dress shirts/pants,
wrinkle-free clothing,
poly/cotton blend
clothing, tablecloths
53 ~ 62 HOT
WARM
COLD
TAP COLD
HIGH
MEDIUM
LOW
NO SPIN
HEAVY
NORMAL
LIGHT
Less
than
8.0 kg
DELICATES Dress shirts/blouses,
nylons, sheer or lacy
garments
41 WARM
COLD
TAP COLD
MEDIUM
LOW
NO SPIN
HEAVY
NORMAL
LIGHT
Less
than
4.0 kg
HAND WASH/
WOOL
Items labeled “hand-
washable”
55 WARM
COLD
TAP COLD
LOW
NO SPIN
NORMAL
LIGHT
Less
than
3.5 kg
SPEED
WASH
Lightly soiled clothing
and small loads
15 HOT
WARM
COLD
TAP COLD
EXTRA
HIGH
HIGH
MEDIUM
LOW
NO SPIN
HEAVY
NORMAL
LIGHT
Less
than
4.0 kg
MFL48165996_E.indd 23 15. 5. 19. 오후 5:24
![](/html/30/30b7/30b724a996c60b42aedc6479b5626e0cbb1d2ca71d2f813bb863181bb87cc2d9/bg18.png)
24
USING YOUR WASHING MACHINE
Items labeled wool or hand-washable,
HAND WASH/WOOL
This cycle is for washing shrinkable woolen or hand-
washable items requiring delicate care. Only wash
woolen items that are labeled machine washable or
hand-washable.
NOTE
y
Laundry weight should be less than 8 pound
(3.6 kg) to prevent damage to the fabric.
y
Use only natural or wool-safe detergent
harmless to fabrics and load 1/2 of the normal
amount of detergent.
y
The HAND WASH/WOOL
cycle uses a gentle
tumble rotation angle and low speed spin for
the ultimate fabric care.
Quick wash,
h
Use the Speed Wash cycle to quickly wash lightly
soiled clothing and small load. For high wash and rinse
efficiency, it is recommended to wash small loads of
2-3 lightly soiled garments.
NOTE
y
Use a little detergent in this cycle. If you want
more rinsing, you can add extra rinse by using
the option button.
Main cycle
You can wash laundry items more thoroughly by
selecting the wash cycle that best suits the type
of items to be washed. Turn the
B
to the desired
cycle. When you select a wash cycle, the light for
the corresponding wash cycle will turn on. See page
22,
Basic operation
, for more details on operating
methods.
Reduce laundry allergen,
ALLERGIENE™
This cycle is a powerful, high temperature cycle
designed specifically to reduce certain allergens.
NOTE
y
Selecting the ALLERGIENE™ cycle
automatically incorporates steam into the wash
cycle.
y
The ALLERGIENE™ cycle can significantly
reduce allergens in bedding and clothing.
y
The ALLERGIENE™ cycle helps reduce dust
mite populations and helps reduce allergens.
y
Due to the higher energy and temperatures
used, the ALLERGIENE™ cycle is not
recommended for wool, silk, leather, or any
other delicate or temperature sensitive items
Reduce laundry bacteria,
SANITARY
This wash cycle reduces 99.9% bacteria on laundry
through high temperature.
Blankets or bulky items,
b
This cycle is for washing blankets or bulky items.
Normal items,
c
Use this cycle to wash all normal items, except delicate
fabrics such as wool or silk.
NOTE
y
If you press
A
and then
C
without selecting
another cycle, the washing machine proceeds
to COTTON/NORMAL.
Wrinkle free items,
d
This cycle is for washing items such as wrinkle-free
clothes or tablecloths to minimize wrinkles.
Sheer items,
f
This cycle is for washing lingerie or sheer and lacy
clothes which can easily be damaged.
MFL48165996_E.indd 24 15. 5. 19. 오후 5:24