LG WD-14030 User Manual

noituloSesuaC elbissoPmotpmyS

• Water supply is not adequate in area

• Water supply taps are not completely open.

• Water inlet hose(s) are kinked.

• The filter of the inlet hose(s) are clogged.

• Drain hose is kinked or clogged.

• The drain filter is clogged.

• Load is too small.

• Load is out of balance.

• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.

• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.

• Is the door opened or not
completely closed?

• Water overfills due to the faulty water
valve.

• Water level sensor has malfunctioned.

• Over load in motor.

• Water leaks

• The washer experienced a power failure.

Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).

Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to “Cleaning the drain pump filter”

Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper

spinning

Close the door completely.

If “ ”is not released, call for service.

Unplug the power plug and call for service.

Close the water tap.
Unplug the power plug.
Call for service.

Call for service.

Restart the cycle.

4

1

2

3

5

7

1 2

3 4

6

60 - 100 cm

@

N

Adjustable feet

Adjustable feet

CAUTION

The appliance is not intended for use by young children or infirm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.

Owner‘s Manual

WD-14030FDS

Safety instructions for use

Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the ope­rating instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always
receives these operating instructions. The following warnings must be strictly observed for safety reasons. They must
be read before installing the appliance and putting it into operation.

• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance
only with cold drinking water and only for washing textiles with washing detergents designed for washing machi­nes. Every other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.

• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.

• Never modify the appliance on your own, as this is dangerous.

• This appliance is heavy. Transporting with care.

• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.

• All installation work must be carried out by a qualified fitter or technician.

• Have electrical connections done by a qualified electrician.

• Never place the appliance on the power cord.

• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.

• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug

- never disconnect by pulling the power cord. Never touch the plug with wet fingers or hands.

• Do not overload the appliance.

• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.

• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to
ignite or parts to warp.

• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.

• Connect the appliance to a suitable wall socket for 220V. Never use an extension cord or double adapter.

• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious
damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized
customer service.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or
explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This
may result in fire or explosion.

• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain
remover has been used then make sure that the solvent has been carefully washed out before inserting the
clothes into the appliance. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not
load oily clothes.

• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly
inflammable gas. Such materials may cause fire or explosion. Never use combustible detergents.

• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.

• After washing, keep the drum door open to protect the door seal.

• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger
of scalding.

• Animals and children may get into the washing machine. So always check the appliance before using it.

• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.

• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the
machine.

• The product should be serviced and repaired only by the authorised customer service using original replacement
parts.

• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable
in order to protect children.

• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.

• If the appliance has been under water then contact the customer service. There is danger of electric shock and
fire.

• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.

• Keep all washing powder and detergents away from children. Danger of poisoning

Before use please read carefully the safety instructions!

Thank you for buying an LG fully automatic washing machine.

Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.

Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.

Remove Packaging

Requirements for installation site

Transit bolts

Electrical connection

Connecting water supply hose

• The appliance is fitted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!

• Packing and all transit bolts must be removed before using
the washing machine.

• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.

Store original packing for future move.
Dispose of packing material according to local regulations.

Unscrew the 4 bolts
using the spanner
supplied.

Keep the 4 bolts and the spanner for the future use. Refit transit bolts before transporting the appliance.

Level floor: Permissible floor gradient under entire washing machine
is 1˚ .

Power socket: Must be within 100 cm of either side of location of
washing machine. Do not overload the socket with more than one
appliance.

Additional Clearance: For wall, floor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry pro­ducts on top of the washing machine at any times. They can damage
the finish or controls of the machine.

1. Do not use an extension cord or double adapter.

2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person
to prevent danger.

3. Always unplug the machine and turn off the water supply after use.

4. Connect the machine to an earthed socket in accordance with current wiring regulations.

5. The appliance must be positioned so that the plug is easily accessible.

• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexpe -
rienced persons may cause injury or serious malfunctioning. Contact your local service centre.

• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.

• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.

• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.

• Make sure the connection to taps is tight enough.

• Periodically check the condition of the hose and replace the hose if necessary.

• Make sure that there is no kink on the hose and that it is not crushed.

Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)

Don’t strip or crossthread when connecting inlet hose to the valve.

If the water supply pressure is more than 1000kPa, a decompression
device should be installed.

• The drain hose should not be placed higher than 100 cm above the floor.

• Proper securing of the drain hose will protect the floor from damage due to any water leakage.

• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.

• Proper level-adjustment of the washing ma­chine prevents excessive noise and vibration.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.

• If the floor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
and resting on the floor. Then check that
the appliance is perfectly level. (Use a spirit
level).

Safety instuctions for the installation

Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.

CAUTION about positioning the appliance

Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.

•

Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.

•

If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.

•

The washing machine must not be installed in rooms where the temperature may drop below 0°C.

•

Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.

•

Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.

CAUTION about the power cord

We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifications of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular atten -
tion to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.

CAUTION about location and moving

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop -
cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic film, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.

CAUTION about the floor surface

• The installation surface must be clean, dry and level.

• Install washing machine on a flat hard floor.

• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.

• The washing machine must be perfectly level and firmly in position.

• It must not “see-saw” across corners under load.

• The installation surface must be clean, free from floor wax and other lubricant coatings.

• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.

Name of product Front loading washing machine

Power supply 220 V~, 50 Hz

Size WxDxH mm: 600 x 640 x 850

Weight 65 kg

Max. Watt

2100 W (Wash) / 1100 W (Steam)

Wash capacity 10.5 kg

Water consumption 59 ℓ (5.6 ℓ / kg)

Permissible water pressure 1.0-10 bar (100-1000kPa)

Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise Have all transit bolts and packing been removed?
Water leaks. Check and tighten hose connections. Unclog drain pipe.

Contact plumber if necessary.

Excessive suds Too much detergent or unsuitable detergent.
Washing machine does not start Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin Check that the door is firmly shut.
Door does not open Once started, the door can not be opened for safety reasons.

Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.

Troubleshooting

Level adjustment

To prevent internal dama­ge during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibrati­on, noise and machine to
malfunction.

Installation of drain hose

Technical Specification

i

If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional
type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.

i

i

The hose supplied with the machine must be used. Old hoses may not be reused

Close the holes with
the caps supplied.

Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.

P/No. :MFL61988476

1

2

3

A

C

B

A

B

C

1 2 3 4 5

1 3

Program

Fabric Type

Water Temp.

(Option)

Cotton

Lightly soiled clothing and
small loads

40

°C

(Cold,

30°C, 60°C)

Cotton, underwear, pillow
covers, bed sheets,
baby wear

Cotton

Quick

Synthetic

Baby Care

Allergy

Care

Delicate

Quick 30

Refresh

Hand Wash

/Wool

Color fast garments (shirts,
nightdresses, pajamas...)and
lightly soiled white cotton
(underwear)

Polyamide, Acrylic, Polyester

Lightly soiled baby wear

Delicate laundry easily
damaged

“Hand wash” marked delicate
and wool laundry

Colored laundry which is lightly
soiled fast

Cotton mixed, Polyester mixed
Dress shirts, blouses

- Time Delay

- Steam Wash

- Intensive

- Time Delay

- Steam Default

- Intensive

- Soak

- Pre Wash

- Crease Care

- Crease Care

- Rinse+Spin

- Medic Rinse

- Rinse+Spin

- Medic Rinse

- Time Delay

- Intensive

- Crease Care

- Rinse+Spin

- Steam Default

60°C

(Cold, 30°C,

40°C, 95°C)

Less than 7 kg

Rating

Less than 4. 5kg

Less than 3. 0kg

Less than 2. 0kg

3 items

40°C (Cold,
30°C, 60°C)

30°C

(Cold, 40°C)

30°C

(Cold, 40°C)

40°C

(Cold, 30°C)

No Choose

60°C

(40°C, 95°C)

60°C

Maximum Load

Option

5

2

1 2 3 4 5

4

INSERT PLUS INTO THE MAINS SOCKE T

Never touch the plug with wet hands!
Never remove the plug from the
socket by pulling on t he cord.

HA NG UP WASTE WATER HOSE

Hose elbow connection e.g. att ach to water tap

WATE R C ON NECT ION

Turn on the water tap

CHECKING THE M ACHI NE

Never use a defect ive machine! In case of any
failure, f irst unplug the machine and turn off the
water

tap.

DOING L AU ND RY AN D U SI NG MACHINE
WITH CA RE

- empty all pockets

- remove all metal part s

- place the delicate tex tiles into the laundr y net

- close zippers

WATE R T REAT MENT

- wi th hardnes s III water

- us e water softening agent

DRUM CARE

- remove extraneous objects

- leave door open to dry the drum

- check the rubber seals regularl y

ECOLOGICA L WAS HI NG

- ma ke use of the max. washing quant it y

- do not “pre wash” if possible

- us e short program if possible

LAUNDRY W ITH DIFFERENT A MO UNTS OF
SOILING

- wash new tex tiles separately

- do not prewash

- pretreat dirt y spots

- pre wash

Sor t the laundry

note wa shing instruction sy mbols -

Degree of soiling -

Type of textile / colour -

Fill the drum

Check the folds of the flex ible gasket (grey) -

and remove any small ar ticles, if any. .

Check inside of the drum and remove -

any left in items for next wash cycle. .

Remove any clothing o r items on t he flexible gasket -

to prevent clot hing and the gasket damages .

Fill detergent

Refer to the

written infor mation

on t he detergent's packing

Turn the machine ON

by pressing the Power button

Select a

Program

Select the

Spinning speed

Select an Option

Pre Wash / Soa k / Crease Care / Rinse + Spin

Select Rinse mode

and Washing temperature

4 additional programs

Press Star t / Pause
to start the washing p rocess

Turn off tap

- Close water supply

- Clean the machine

- Unplug machine

Additional Steps

- Turn the machine off

- Leave door open to
allow drum to dr y

Remove laundr y

- Open the door

- Remove t he laundry

W

a

it

u

n

t

i

l

w

a

s

h

i

ng

i

s

f

i

n

i

s

h

e

d

Time Delay / Steam Wash / Intensive / Medic Rinse

Main Wash

For very dirty clothes fill 1/4 of the
por tion of detergent in here and
select a prewashing programm

Sof tener

Do not exceed the MAX-Leve l.
Highly de nsed sof teners are to
be diluted with some water.

Pre Wash

For normal dir ty clot hes use a small
amount of detergent. Don't pre wash.
Mount the level plate to use fluid detergents.

Dry flat

Do not bleach

Handy to bleach

Do not
tumble dry

Hang to dry

Drip dry

Medium hot
ironing

Hot ironing

Do not iron

Washing
temperature

Do not wash

Luke warm ironing

Turn off the water
tap

Unscrew t he water
inlet hose

Pull out t he water
inlet filter

Clean the filter using
a ha rd brist le brush

Pull out t he
dispenser drawer

Clean the dispenser
drawer under flow­ing water

Clean inside the
recess with an old
toothbrush

Inser t t he dispenser
drawer

Cleaning the water inlet filter

Cleaning the dispenser drawer

Open t he lower cover
cap. Drain plug to
pull out the hose

Unplug the drain plug.
Then open the fil ter
by t urning to t he lef t

Remove any
ext ra neous matter
from the pump filter

After cleaning, t ur n
the pump filter and
inser t t he drain plug

Time Delay

Set ting “ Time Delay” determines when machine stops.

How to set “Time Delay”

- Press Power button.

- Turn the Program dial to select the progra m you require.

- Press Time Delay button and set time required.

- Press the Start/ Pause button.

Intensive

If the laundry is heavily soiled “Intensive”option is ef fective.

- By selecting the Intensive option, the washing durat ion may be extended,
depending on the program selected.

- To use t his option, press the intensive button once before the wash program is star ted.

Medic Rinse

For best results or for cleaner rinsing, select the “Medic Rinse” option.

Available in the Cotton, Cotton Quick, Synthetic, and Baby Care programs.
Medic Rinse is set by default in the Baby Care program.
The respect ive temperature indicator will light up.

Steam Washing and Refresh cycle

Steam Wash is

- For heavil y stained clothes, under wear, or baby clothes.

- Steam Wash is ava ilable with t he Cotton, Cot ton Quick, Synthet ic, Baby Care, A llergy Care programs.

- Refresh cycle is always Steam wash.

- Do not load delicate s such as wool, silk, and ea sily discolored clothes.

Program Temperature Program Temperature

Cot ton

Cold, 30°C, 40°C, 60°C, 95°C

Baby Care 40°C, 60°C, 95°C

Cot ton Quick Cold, 30°C, 40°C, 60°C Ref resh No c hoose

Synthetic Cold, 30°C, 40°C, 60°C Allergy Ca re 60°C

How to use Refresh C ycle

Spinnin g cycle

Temperature

Rinse

OptionsSta rt / Pa useProg ram Cycle

Powe r bu tt on

Drum

Dispenser
drawer

Cover cap

Control panel

Washing program table

Additional programs

Preparation

lightly

heavily

Tighten up the inlet
hose

Cleaning the drain pump filter

Close the lower
cover cap

Washing symbols

Dispenser drawer

Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry.

Cleaning and Maintenance

Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock.

DisplayAdditiona l programs

Steam Cycle

Note:

To use programs in the
Steam-Cycle, please press
first the “Steam Wash” but ton
(see additional programs).

Refr esh Allerg y Ca re Baby Care Cotton Synthet icCot ton Quick

Exterior

Proper ca re of your wa shing machine can extend its ser vice life. T he
out side of t he machine can be cleaned with wa rm water and a neutral
non-abrasive household detergent. Immediately wipe off any spillage.
Wipe with damp cloth. Avoid striking the surface with sharp objects. Never
hose down the machine!

Interior

Dry around the washing machine door
opening, flexible gasket and door glas s.
Run washing machine through a complete
cycle using hot water. Repeat process if
necessa ry.

Cleaning in general

Important: Do not use methylated spirits, solvents or similar products.

Water Temperature: Sele ct water temperat ure to suit wash c ycles. Always follow ga rment ma nufacture’s ca re label or instr uctions when washing.
Intensive: If the laundr y is heavily soiled “Intensive” option is effective.
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cot ton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic and Baby Care program.
Crease Care: If you want to prevent creasing, select Crease Care option.
Medic Rinse: For best results or for cleaner rinsing, you can choose Medic Rinse option. Medic Rinse is set by default in the Baby Care program.

By pressing the Steam Wash bu tton, Steam Function can be selecte d.
When Steam Function is selected, Steam wash (

) LED lights up.

Steam Washing features enhance washing performance with low
energy consumption. Refresh cycle reduces creases in clothes.

Select the Refres h
program

Load 3 items or less
and close the door

Press the Steam Wa sh button repeatedly unt il the
required and correct number of items is displayed

Press the
Start/ Pause
but ton

2 41 3

The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are
washed according to the instructions o n t he garment label and t hose issued by the manufact urer of this washing machine M0708.

Notes

Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment c are.

Warning: Keep all washing powder and detergents away from children. Danger of poisoning

1 2

1 2 3 4 5

6 3 se c.

Change to the desired program, whilst in child lock mode:

Empty the drum
completly and
close the door

Add anti-limescale
(Calgon) to the main
wash compartment.
Close the disp.
drawer

Power ON with
Then press and
hold Rinse and
Temp. button

Press the
Start/ Pause
button to start Tub
Clean process

After the cycle is
complete, leave
the door open
to dry

Select this function to l ock the butto ns o n the control panel and to preven t tamperin g.

Press and hold
the Option
buttons
simultaneously

Press
Start/
Pause

Select the desired
program

Press
Start/ Pause

6 3 se c.

6 3 se c.

The Beep on/off function can be set only during the
washing cycle.

To set the Beep On/Of f function follow the below steps.

1. Turn on the washing machine (by pressing the Power
button).

2. Press the Start /Pause but ton.

3. Press and hold the Option and Rinse button simulta­neously for three seconds to set Beep on/off
function.

Once the Beep on/off function is set, the setting is
memorized even after Power is off.

Child Lock

6 3 se c.

TU B CLE AN is special cycle to cle an the inside of th e wa shing machine.
A higher water level is used in this cyle at higher spin speed. Perf orm this cycle re gul arly.

Tub Clean

Beep on / off

To deactivate:

press and hold
the Option but­tons simulta­neously for 3
seconds until the
" " is removed
from the display.

To activate:

press and hold
the Option but­tons simultane­ously until " "
appears in the
display.