LG WD-13513RDA Owner’s Manual

Before beginning installation, read these

instructions carefully. This will simplify installation

and ensure that the washer is installed correctly

and safely. Leave these instructions near the

washer after installation for future reference.

USER’S GUIDE &

INSTA L L ATION INSTRUCTIONS

P/NO. MFL31245122

Avant de commencer à installer votre machine à laver,

lisez attentivement ces instructions. Cela simpliﬁera votre installation et assurera que la machine à laver est installée correctement et en toute sécurité. Conservez

ces instructions à proximité de la machine à laver après

son installation, pour référence future.

Mo del/ Modè le

WM3988H**

Designed specially to use only HE (High-Efﬁciency) detergent

Spécialement conçue pour une utilisation avec les détergents HE (haute efﬁcacité) seulement.

Front Loading

St eam Combo

GUIDE DE L’UTILISAT E U R E T

DIRECTIVES D’INSTA L L ATION

La ve-linge à vapeur et

ch argeme nt frontal

To contact LG Electronics, 24 hours a day, 7 days a week:

1-888-542-2623

Or visit us on the Web at: ca.lge.com

Pour contacter LG Electronics, 24 heures par jour, 7 jours par semaine :

1-888-542-2623

Ou visitez notre site Web à l’adresse :

ca.lge.com

Protocol P172 Sanitization Performance of Residential and Commercial, Family Sized Clothes Washers Protocole P172

Performance en matière d'assainissement des laveuses résidentielles et commerciales de grande taille.

I M P O RTA N T S A F E T Y I N S T RUC T I O N S

Congratulations on your purchase

and welcome to the LG family.

Your new LG Steam Washer™

combines the most advanced

washing technology with simple

operation and high efficiency.

By following the operating and care

instructions in this manual, your

washer will provide you with many

years of reliable service.

THANK YOU!

I N T RO D U C T I O N

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:

wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions. wWARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

INSTALLATION INSTRUCTIONS

Choose the Proper Location .................................. 9

Clearances ............................................................. 9

Flooring ................................................................ 10

Installations With Optional Pedestal Base

or Stacking Unit .................................................... 10

Unpacking and Removing Shipping Bolts ........... 11

Connecting the Water Lines ................................. 12

Connecting the Drain Line .................................... 13

Leveling the Washer ............................................. 14

HOW TO USE

Sorting Wash Loads ............................................. 15

Selecting Detergent .............................................. 16

About the Dispenser ............................................. 16

Loading the Dispenser ......................................... 17

Control Panel Features ......................................... 18

Cycle Guide .......................................................... 19

The LCD Display ................................................... 20

Operating the Washer .......................................... 21

Steam Cycles ....................................................... 22

Cycle Setting Buttons .................................... 23–25

Cycle Option Buttons .................................... 25-26

Special Functions ........................................... 26-27

PARTS AND FEATURES

Special Features ..................................................... 7

Key Parts and Components ................................... 8

TROUBLESHOOTING

Normal Sounds You May Hear ............................. 31

Before Calling for Service ............................... 31–33

CARE AND CLEANING

Regular Cleaning .................................................. 27

Cleaning the Washer ............................................ 28

Maintenance ................................................... 29–30

WARRANTY ................................................... 35

SPECIFICATIONS/OPTIONAL ACCESSORIES

IMPORTANT SAFETY INSTRUCTIONS

Basic Safety Precautions .................................. 3–6

Key Dimensions and Speciﬁcations ..................... 34

Optional Accessories ........................................... 34

Product Registration Information

Model: Serial Number: Date of Purchase:

The model and serial number can be located on the rating plate on the back of the washer.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

READ ALL INSTRUCTIONS BEFORE USE

• Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation

instructions are packed in the washer for installer's reference. If the washer is moved to a new location, have it checked and reinstalled by a qualiﬁed service person. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• Do not, under any circumstances cut or remove the third (ground) prong from the power cord. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• For personal safety, this appliance must be properly grounded. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to

minimize the possibillty of electric shock hazard from this appliance.

• This washer must be plugged into a 120VAC, 60Hz grounded outlet. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• Have the wall outlet and circuit checked by a

qualiﬁed electrician to make sure the outlet is properly grounded. Failure to follow this warning

can cause serious injury, ﬁre, electrical shock, or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow

this warning can cause serious injury, ﬁre, electrical shock, or death.

• Do not install on carpet. Install washer on a solid ﬂoor. Failure to follow this warning can cause serious leak damage.

• Do not remove ground prong. Do not use an

adapter or extension cord. Plug into a grounded 3-prong outlet. Failure to follow these warnings can

cause serious injury, ﬁre, electrical shock, or death.

• The washer should always be plugged into its

own individual electrical outlet which has a voltage rating that matches the rating plate. This

provides the best performance and also prevents overloading house wiring circuits which could cause a ﬁre hazard from overheated wires.

• Never unplug your washer by pulling on the power cord. Always grip plug ﬁrmly and pull straight out from the outlet. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• Repair or replace immediately all power cords

that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. Failure

to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• When installing or moving the washer, be careful not to pinch, crush, or damage the power cord. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• The washer must be installed and electrically

grounded by a qualiﬁed service person in accordance with local codes to prevent shock

hazard and assure stability during operation.

• Washer is heavy. Two or more people may be needed to install and move the appliance. Failure to do so can result in back or other injury.

• Store and install the washer where it will not

be exposed to temperatures below freezing or exposed to outdoor weather conditions. Failure to

follow this warning can cause serious leak damage.

• Do not install the washer in humid spaces to reduce the risk of electric shock. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following.

SAFETY INSTRUCTIONS FOR INSTALLATION

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

READ ALL INSTRUCTIONS BEFORE USE

I M P O RTA N T S A F E T Y I N S T RUC T I O N SI M P O RTA N T S A F E T Y I N S T RUC T I O N S

• Before use, the washer must be properly installed as described in this manual.

• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other ﬂammable or explosive substances, as they give off vapors that could ignite or explode.

• Do not add gasoline, dry cleaning solvents, or other ﬂammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn on all hot water faucets and let the water ﬂow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is ﬂammable, do not smoke or use an open ﬂame during this time.

• Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children.

• Before the washer is removed from service or discarded, remove the door to prevent children from climbing inside.

• Do not install or store the washer where it will be exposed to the weather or freezing temperatures.

• Do not tamper with controls.

• Do not repair or replace any part of the washer or attempt any servicing other than as described in this manual. We strongly recommend that any service be performed by a qualiﬁed individual.

• See Installation Instructions for grounding requirements.

• ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

• Do not place items exposed to cooking oil in your washer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch ﬁre.

• Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

• This washer is not designed for maritime use or for mobile installations such as in RVs, aircraft, etc.

• Turn off the water taps and unplug the washer if the machine is to be left for an extended period of time, such as during vacations.

• Do not use to dry articles containing foam rubber or similarly textured rubber-like materials.

• Interior of washer and condensing duct should be cleaned periodically by qualiﬁed service personnel.

• Packaging material can be dangerous for children. There is a risk of suffocation! Keep all packaging from children.

• Always check the inside of the washer for foreign objects before loading laundry. Keep the door closed when not in use.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following.

BASIC SAFETY PRECAUTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

GROUNDING INSTRUCTIONS

wWARNING: Improper connection of the equipment-grounding conductor can result in risk

of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause serious injury, fire, electrical shock, or death.

I M P O RTA N T S A F E T Y I N S T RUC T I O N S

SAFETY INSTRUCTIONS FOR USE, CARE AND CLEANING, AND DISPOSAL

•

Unplug the washer before cleaning to avoid the

risk of electric shock.

•

Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will

damage the ﬁnish.

•

Do not put oily or greasy rags or clothing on top of the washer. These substances give off

vapors that could ignite the materials.

•

Do not wash items that are soiled with vegetable or cooking oil. These items may

contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch ﬁre by itself.

•

Disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply. Failure to follow this

warning can cause serious injury, ﬁre, electrical shock, or death.

•

Do not combine laundry products for use in one load unless speciﬁed on the label.

•

Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when using laundry products.

Incorrect usage can produce poisonous gas, resulting in serious injury or death.

•

Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, push in the cycle selector knob and allow the drum to coast to a complete stop before reaching inside. Failure to follow this

warning can cause serious injury, ﬁre, electrical shock, or death.

•

Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to

comply with these warnings could result in serious personal injuries.

•

Destroy the carton, plastic bag, and other packing materials after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers.

Failure to comply with these warnings could result in serious personal injuries.

•

Keep laundry products out of children’s reach. To prevent personal injury, observe all warnings on product labels. Failure to comply with these

warnings could result in serious personal injuries.

•

Remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside before your washer is removed from service or discarded. Failure to do

so can result in serious personal injury or death.

PA RTS A N D F E AT U R E S

SPECIAL FEATURES

DETERGENT DISPENSER DRAWER

This four-compartment drawer provides separate dispensers for prewash and main wash detergent, liquid bleach, and liquid fabric softener.

CONTROL PANEL LCD DISPLAY SCREEN

Simple electronic controls are user-friendly. The LCD screen shows cycle options and cycle information and displays status messages during operation.

EASY-ACCESS LOCKING DOOR

Extra-large door locks during operation and features a delay to prevent the door from being opened until the washer interior has cooled and the water level has lowered.

HIGH-EFFICIENCY STEAM CYCLES

During LG’s unique high-efficiency STEAM cycles, the steam nozzle injects fabrics with hot steam to gently remove tough stains.

ROLLERJETS

The RollerJet system enhances wash performance while reducing fabric wear. Integrated jets spray clothes to further improve washing efficiency.

INTERIOR DRUM LIGHT

The drum light illuminates the washer interior for greater visibility when loading and unloading. The ultra long-life LED bulbs should never need replacement.

DIRECT-DRIVE MOTOR

Direct-drive motor eliminates the belt and pulleys found on most washers to provide improved performance and reliability while increasing energy efficiency.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following.

SAVE THESE INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

PA RTS A N D F E AT U R E S I N S TA L L AT I O N I N S T RU C T I O N S

CHOOSE THE PROPER LOCATION

CLEARANCES

Allow at least 24 in. (61.2 cm) in front of the washer to open the door.

293/4"

(75.6 cm)

(10 cm)

51"

(129.5 cm)

211/4"

(54 cm)

To ensure sufficient clearance for water lines and airflow, allow minimum clearances of at least 1 in. (2.5 cm) at the sides and 4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or floor moldings that may increase the required clearances.

• Do not remove ground prong. Do not use

an adapter or extension cord. Plug into a grounded 3-prong outlet. Failure to follow this

warning can cause serious injury, ﬁre, electrical shock, or death.

Power Outlet

• The power outlet must be within 60 in. (1.5 m) of either side of the washer.

• The appliance and outlet must be positioned so that the plug is easily accessible.

• Do not overload the outlet with more than one appliance.

• The outlet must be grounded in accordance with current wiring codes and regulations.

• Time-delay fuse or circuit breaker is recommended.

NOTE: It is the personal responsibility and obligation of the product owner to have a proper outlet installed by a qualified electrician.

HIGH

WASHING

HIGHHOT/

COLD

STEAM

DOOR LOCK

EST. TIME: REMANING

NORMAL

CHILD LOCKDELAY WASH

1:21

27"

(68.6 cm)

(2.5 cm)

Hot and Cold Water Inlets

Drain Hose

Rear of Washer

KEY PARTS AND COMPONENTS

In addition to the special features and components outlined in the Special Features section, there are several other important components that are referenced in this manual.

ULTRA-CAPACITY STAINLESS STEEL DRUM

The ultra-large stainless steel drum offers extreme durability and is tilted to improve efficiency and allow easier access for large items.

WATER CIRCULATION AND STEAM NOZZLES

The water circulation nozzles spray the water/ detergent solution directly onto garments for super cleaning performance. During LG’s unique high-efficiency STEAM cycles, the steam nozzle injects fabrics with hot steam to gently remove tough stains.

LEVELING FEET

Four leveling feet (two in the front and two in the back) adjust to improve washer stability on uneven floors.

DRAIN ACCESS PANEL

Provides access to the drain line and drain pump filter.

wWARNING

• Washer is heavy! Two or more people are required when moving and unpacking the washer. Failure to do so can result in back

or other injury.

• Store and install the washer where it will not

be exposed to temperatures below freezing or exposed to outdoor weather conditions.

Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• Properly ground washer to conform with all

governing codes and ordinances. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• To reduce the risk of electric shock, do not

install the washer in humid spaces. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

• The base opening must not be obstructed by

carpeting when the washer is installed on a carpeted ﬂoor.

Included Accessories

Hot and Cold Water Hoses

Wrench

(for removing

shipping bolts and

adjusting leveling feet)

Tie Strap (for securing drain hose)

Elbow Bracket (for securing drain hose)

Caps (4) (for covering shipping bolt holes)

I N S TA L L AT I O N I N S T RU C T I O N S

FLOORING

I N S TA L L AT I O N I N S T RU C T I O N S

When removing the washer from the carton base, be sure to remove the foam tub support in the middle of the carton base.

If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. Do NOT lay the washer on its front or back.

IMPORTANT: To prevent internal damage during transport, the washer is equipped with 4 shipping bolts and plastic retainers. These bolts and retainers MUST be removed before operating the washer.

• Failure to remove shipping bolts and retainers

may cause severe vibration and noise, which can lead to permanent damage to the washer. The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.

Remove the retainers by turning them slightly while pulling. Rotate and press the hole caps into the shipping bolt holes.

Starting with the bottom 2 shipping bolts, use the included wrench to remove the 4 shipping bolts by turning them counterclockwise.

Shipping Bolts

NOTE: Save the bolts and retainers for future use. To prevent damage to internal components, the shipping bolts and retainers must be installed when transporting the washer.

NOTE: Please note that the floor must be strong and rigid enough to support the weight of the washer when fully loaded, without flexing or bouncing. If your floor has too much flex in it, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a frontloading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

INSTALLATIONS WITH OPTIONAL PEDESTAL BASE OR STACKING KIT

IMPORTANT: If you are installing your washer using an optional pedestal base or stacking kit, please refer to Optional Accessories in this manual or to the instructions for your pedestal or stacking kit before proceeding with the installation.

Retainer

Hole Cap

30"

(76.1 cm)

(10 cm)

HIGH

WASHING

HIGHHOT/

COLD

STEAM

DOOR LOCK

EST. TIME: REMANING

NORMAL

CHILD LOCKDELAY WASH

1:21

27"

(68.6 cm)1"(2.54 cm)

(2.54 cm)

771/2"

(190.5 cm)

Required Dimensions for Installation

With Pedestal

Required Dimensions for Installation

With Stacking Kit

Carton Base

Foam Tub Support

• To minimize noise and vibration, the washer MUST be installed on a solidly constructed ﬂoor. See the NOTE at right.

• Allowable slope under the entire washer is 1° maximum.

• Carpeting and soft tile surfaces are not recommended.

• Never install the washer on a platform or weakly supported structure. Use only an approved accessory pedestal as described below.

UNPACKING AND REMOVING SHIPPING BOLTS

I N S TA L L AT I O N I N S T RU C T I O N S I N S TA L L AT I O N I N S T RU C T I O N S

CONNECTING THE WATER LINES CONNECTING THE DRAIN LINE

Insert the end of the drain hose into the floor drain. Secure the hose in place to prevent it from moving.

Drain Hose

Floor Drain

Option 3: Floor Drain

Stand Pipe

Tie Strap

Clip the end of the hose into the elbow bracket. Insert the end of the drain hose into a standpipe. Use tie strap to secure the drain hose in place.

NOTE: Total height of the hose end should not exceed 96 in. (244.8 cm) from the bottom of the washer.

Option 1: Standpipe

Elbow Bracket

Drain Hose

Clip the end of the hose into the elbow bracket. Hang the end of the drain hose over the side of the laundry tub. Use tie strap to secure the drain hose in place.

NOTE: Total height of the hose end should not exceed 96 in. (244.8 cm) from the bottom of the washer.

Laundry Tub

Option 2: Laundry Tub

Elbow Bracket

Tie Strap

Drain Hose

Insert a rubber seal into the threaded ﬁttings on each hose.

Rubber Seal

Water Hose (to tap)

Rubber Seal

Water Hose (to water inlet on washer)

Attach the hot water line to the hot water tap. Attach the cold water line to the cold water tap.

Tighten the ﬁttings securely. Open the water taps fully to check for leaks.

Water Tap

NOTE: Do not cross-thread the hose ﬁttings. Attach the hot water line to the red hot water

inlet on the back of the washer. Attach the cold water line to the blue cold water inlet on the back of the washer. Tighten the fittings securely.

Water Inlets

• IMPORTANT: Use new hoses when installing the washer. Do NOT reuse old .

• IMPORTANT: Use ONLY the inlet hoses provided by LG with this laundry product. Aftermarket hoses are not guaranteed to ﬁt or function correctly. Other hoses may not tighten correctly and could cause leaks. Subsequent damage to product or property will not be covered under the terms of LG's warranty.

• Water supply pressure must be between

14.5 PSI and 116 PSI (100~800 kPa). If the water supply pressure is more than 116 PSI, a pressure reducing valve must be installed.

• Periodically check the hose for cracks, leaks, and wear, and replace the hose if necessary.

• Make sure that the water lines are not stretched, pinched, crushed, or kinked.

• The washer should never be installed or stored in a location subject to freezing temperatures. Damage to the water lines and internal mechanisms of the washer can result. If the washer was exposed to freezing temperatures prior to installation, allow it to stand at room temperature for several hours before use.

• The drain hose should always be properly secured. Failure to properly secure the drain hose can result in ﬂooding and property damage.

• Do not install the end of the drain hose higher than 96 in. (244.8 cm) above the bottom of the washer.

• The drain must be installed in accordance with any applicable local codes and regulations.

• Make sure that the water lines are not stretched, pinched, crushed, or kinked.

I N S TA L L AT I O N I N S T RU C T I O N S

SORTING WASH LOADS

H O W TO U S E

LEVELING THE WASHER

Loosen the locknuts on all 4 leveling feet until you can turn the feet with the included wrench. Turn clockwise to raise the washer or counterclockwise to lower it.

Once the washer is level from side to side and front to back, tighten all locknuts securely.

Make sure that all 4 leveling feet are in firm contact with the floor.

NOTE: To make sure that the washer is properly level, run the washer with a test load: place approximately 6 pounds of laundry in the machine. Then press POWER, press RINSE+SPIN, and then press the START/PAUSE button. See the following sections for additional information on cycle selection and operation.

Verify that the washer does not rock or vibrate excessively during the spin cycle. If the washer vibrates or shakes, adjust the leveling feet until the washer is stable and retest.

Fabric Care Labels

Most articles of clothing feature fabric care labels that include instructions for proper care.

Grouping Similar Items

For best results, sort clothes into loads that can be washed with the same wash cycle.

Different fabrics have different care requirements. Always wash dark colors separately from light

colors and whites to prevent discoloration. If possible, do not wash heavily soiled items with lightly soiled ones. The chart below shows recommended groupings.

Bleach symbols

Any bleach

(when needed)

Only non-chlorine bleach

(when needed)

Do not bleach

Machine wash cycle

Normal

Permanent press/

wrinkle resistant

Gentle/

delicate

Hand wash

Do not wash Do not wring

Water temperature

Hot

(50°C/120°F)

Warm

(40°C/105°F)

Cold/cool

(30°C/85°F)

Fabric Care Labels

Sort Laundry...

by Colors by Soil by Fabric by Lint

Whites Heavy Delicates Lint Producer Lights Normal Easy Care Lint Collector Darks Light Sturdy

Loading the Washer

• Check all pockets to make sure that they are empty. Items such as clips, matches, pens, coins, and keys can damage both your washer and your clothes.

• Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling on other clothes.

• Pretreat heavily stained areas for best results.

• Combine large and small items in a load. Load large items ﬁrst.

• Large items should not be more than half of the total washload.

• The washer can be fully loaded, but the drum should not be tightly packed with items. The door of the washer should close easily.

• To prevent an out-of-balance load, do not wash single items. Add one or two similar items to the load. Large, bulky items, such as a blanket, comforter, or bedspread should be washed individually.

• Do not wash or spin waterproof clothes.

• When unloading the washer, check under the door seal for small items.

Position the washer in the final location, taking special care to not pinch, strain, or crush the water and drain lines. Place a level across the top of the washer.

Level

Leveling Feet

The drum of your new washer spins at very high speeds, up to 1,320 RPM. To minimize vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level the washer. Extending the leveling feet more than necessary can cause the washer to vibrate.

• All four leveling feet must rest solidly on the ﬂoor. Rock the washer gently from corner to corner to make sure that the washer does not rock.

If you are installing the washer on the optional pedestal, you must use the leveling feet on the pedestal to level the washer. The washer’s leveling feet should be fully retracted and locked into position with the locknuts.

Raise

Lower

Tighten all 4 locknuts securely

NOTE: The capacity of the machine for washing clothes is twice as much as when drying clothes. If the machine is to be used to dry a load, then the wash load must be reduced by half for effective drying performance. If a full load is washed, remove half the clothes prior to starting the dry cycle.

H O W TO U S E

SELECTING DETERGENT

ABOUT THE DISPENSER

The automatic dispenser consists of four compartments which hold:

• Liquid chlorine bleach.

• Liquid fabric softener.

• Liquid or powdered detergent for prewash.

• Liquid or powdered detergent and color-safe bleach for main wash.

All laundry products can be added at once in their respective dispenser compartments. They will be dispensed at the appropriate time for the most effective cleaning.

After adding the laundry products to the dispenser, close the dispenser drawer.

To add detergent, bleach, and fabric softener to the automatic dispenser:

Open the dispenser drawer. Load the laundry products into the

appropriate compartments.

Slowly close the dispenser drawer to

avoid early dispensing of the laundry products.

NOTE: It is normal for a small amount of water to remain in the dispenser compartments at the end of the cycle.

1 2

Liquid Chlorine Bleach Compartment

Liquid Fabric Softener Compartment

Prewash Detergent Compartment

Main Wash Detergent Compartment

Liquid Detergent Cup

Insert

H O W TO U S E

IMPORTANT: Do not place or store laundry products, such as detergent, bleach, or liquid fabric softener, on top of your washer or dryer. Wipe up any spills immediately. These products can damage the finish and controls.

Designed specially to use only HE (High-Efﬁciency) detergent

IMPORTANT: Your Steam Washer™ is designed for use with only High-Efficiency (HE) detergents. HE detergents are formulated specifically for front-load washers and contain suds-reducing agents. Always look for the HE symbol when purchasing detergent.

HE detergents produce fewer suds, dissolve more efficiently to improve washing and rinsing performance, and help to keep the interior of your washer clean.

Using a regular detergent may cause oversudsing and unsatisfactory performance.

LOADING THE DISPENSER

Prewash Detergent Compartment

Add liquid or powdered detergent to this compartment when using the Prewash option. Always use HE (High-Efficiency) detergent with your washing machine.

• The amount of detergent added for the Prewash option is 1/2 the amount recommended for the main wash cycle. For example, if the main wash cycle requires one measure of detergent, add 1/2 measure for the Prewash option.

NOTE: If liquid detergent is to be used for the main wash when using the pre-wash option, the liquid detergent cup accessory must be used in main wash dispenser to prevent the main wash liquid detergent from being dispensed immediately.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle, which is added to the load at the beginning of the cycle. Always use HE (High-Efficiency) detergent with your washing machine.

Never exceed the manufacturer’s recommendations when adding detergent. Using too much detergent can result in detergent buildup in clothing and the washer. Either powdered or liquid detergent may be used.

• When using liquid detergent, make sure the liquid detergent cup and insert are in place. Do not exceed the maximum ﬁll line.

• When using powdered detergent, remove the insert and liquid detergent cup from the compartment. Powdered detergent will not dispense with the liquid detergent cup and insert in place.

NOTE: Liquid or powdered color-safe bleach may be added to the main wash compartment with detergent of the same type.

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which will be dispensed automatically at the proper time during the wash cycle.

• Do not add powdered or liquid color-safe bleach to this compartment.

• Always follow the manufacturer’s recommendations when adding bleach. Do not exceed the maximum ﬁll line. Using too much bleach can damage fabrics.

• Never pour undiluted liquid chlorine bleach directly onto the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which will be automatically dispensed during the final rinse cycle.

• Always follow the manufacturer’s recommendations when adding fabric softener. Do not exceed the maximum ﬁll line. Using too much fabric softener may result in stained clothes.

• Dilute concentrated fabric softeners with warm water. Do not exceed the maximum ﬁll line.

• Never pour fabric softener directly onto the load or into the drum.

Designed specially to use only HE (High-Efﬁciency) detergent

H O W TO U S E H O W TO U S E

CYCLE GUIDE

CONTROL PANEL FEATURES

POWER ON/OFF BUTTON

Press to turn the washer ON. Press again to turn the washer OFF.

NOTE: Pressing the ON/OFF button during a cycle will cancel that cycle and any load settings will be lost.

CYCLE SELECTOR KNOB

Turn this knob to select the desired cycle. Once the desired cycle has been selected, the standard presets will be shown in the display. These settings can be adjusted using the cycle setting buttons anytime before starting the cycle.

START/PAUSE BUTTON

Press this button to START the selected cycle. If the washer is running, use this button to PAUSE the cycle without losing the current settings.

NOTE: If you do not press the START/PAUSE button within 8 minutes of selecting a cycle, the washer automatically turns off.

STEAM BUTTON

Press the STEAM button to add steam to the selected cycle for added cleaning power.

NOTE: Steam can only be added to the following cycles: STEAMFRESH™, SANITARY, BULKY/LARGE, PERM. PRESS, COTTON/ NORMAL, and ALLERGIENETM.

CYCLE SETTING BUTTONS

Use these buttons to select the desired cycle options for the selected cycle. The current options are shown in the display. Press the button for that option to view and select other settings.

DELAY BUTTON

Press this button to delay the start of the wash cycle. Each press of the button increases the delay time by one hour, up to 19 hours.

LCD DISPLAY

The display shows the settings, estimated time remaining, options, and status messages for your Steam Washer™. The light in the display will remain on through the cycle.

OPTION BUTTONS

The option buttons allow you to select additional cycle options and will light when selected. Certain buttons also allow you to activate special functions by pressing and holding the button for 3 seconds.

For detailed information about the individual options, please see the following pages.

Cycle

Steam Fresh

Dress shirts, blouses

Heavily soiled underwear, work clothes, diapers, etc.

Extra Hot/Cold

High

Extra High

No Spin

Low

Medium

Normal

Heavy

Light

Normal

Heavy

Light

Normal

Heavy

Light

Normal

Heavy

Light

Normal

Light

Normal

Heavy

Light

Low

Medium No Spin

Medium

High

No Spin

Low

High

Extra High

No Spin

Low

Medium

No Spin

Low

No Spin

High

Extra High

No Spin

Low

Medium

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

Warm/Cold

Warm/Warm

Large items such as blankets and comforters

Dress shirts/pants, wrinkle-free clothing, poly/cotton blend clothing, tablecloths

Cotton, linen, towels, shirts, sheets, jeans, mixed loads

Dress shirts/blouses, nylons, sheer or lacy garments

Items labeled “hand-washable”

Cotton, underwear, pillow covers, bed sheets, baby wear

Sanitary

Bulky/ Large

Perm Press

Cotton/ Normal

Delicates

Hand Wash/

Wool

ALLERGIENE

Fabric Type

Wash/Rinse

Temp.

Spin Speed Soil Level

Pre-

Wash

Rinse +

Spin

Water

Plus

Stain Cycle

Dry Steam

Extra Rinse

Light

Normal

Heavy

Extra High

No Spin

Low

Medium

High

Hot/Cold

Cold/Cold

Warm/Cold

Warm/Warm

Lightly soiled clothing and small loads

Speed Wash

The cycle guide below shows the options and recommended fabric types for each cycle.

NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle.

H O W TO U S EH O W TO U S E

THE LCD DISPLAY

The LCD display shows the settings, estimated time remaining, options, and status messages for your washer. When the washer is turned on, the light in the display will illuminate.

STATUS/CYCLE DISPLAY

This portion of the display shows the selected cycle, operating status, and special messages. If a cycle has special instructions, they will also be displayed in this area.

ESTIMATED TIME REMAINING

When the START/PAUSE button is pressed, the washer automatically detects the wash load (weight) and optimizes the washing time, based on the selected cycle and options. The display will then indicate the estimated time remaining for the selected wash cycle.

NOTE: The cycle time displayed may appear much longer than that of a top-loading washer. The displayed time is for the complete cycle, rather than just the agitation portion of the cycle, as is typically shown on a top-loading washer.

CYCLE COMPLETION INDICATOR

Shows how much of the current wash cycle has been completed.

STEAM CYCLE INDICATOR

Indicates that a STEAM cycle has been selected.

DOOR LOCK INDICATOR

Indicates that the door is locked. The washer door will lock while the washer is operating. The door can be unlocked by pressing the START/ PAUSE button to stop the washer.

NOTE: If the temperature in the washer is too high, the door cannot be unlocked until the washer has cooled. If the water level is too high, select the DRAIN & SPIN cycle to drain excess water. Do not try to force open the door.

CHILD LOCK INDICATOR

When CHILD LOCK is set, the Child Lock indicator will appear and all buttons are disabled except the ON/OFF button. This prevents children from changing settings while the washer is operating.

DELAY WASH INDICATOR

This indicator shows that the washer has been set for DELAY WASH. The washer will start automatically after the set delay time has passed.

CYCLE SETTING INDICATORS

These indicators show the current cycle settings for WASH/RINSE, SPIN SPEED, SOIL LEVEL, and DRY. To change these settings, press the appropriate settings button.

NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle.

6 7

OPERATING THE WASHER

Press the ON/OFF button to turn on the

washer. The lights around the cycle selector knob will illuminate.

Turn the cycle selector knob to the desired

cycle. The display will show the preset Rinse/Wash Temperature, Spin Speed, Soil Level, and Option settings for that cycle.

If you would like to change the settings for that cycle, press the option button(s) to display additional settings for that option. Press the button again to cycle through the settings until the desired setting is highlighted.

NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle.

Select any additional cycle options, such as

STEAM or DELAY by pressing the button for that option.

NOTE: To protect your garments, not every wash/rinse temperature, spin speed, soil level, or option is available with every cycle.

Press the START/PAUSE button to begin

the cycle. The door will latch, the display will change, and the washer will calculate the

estimated time remaining. Once the washer has calculated the estimated total cycle time, the washer will start. To pause the cycle at any time, press PAUSE.

NOTE: The cycle time displayed may appear much longer than that of a toploading washer. The displayed time is for the complete cycle, rather than just the agitation portion of the cycle, as is typically shown on a top-loading washer.

Washing time can be reduced significantly for small or lightly soiled loads by selecting the Speed Wash cycle and setting the Soil Level button to Light.

Once you have loaded the washer and added laundry products (detergent, bleach, and/or fabric softener):

When the load is finished, the beeper (if set) will sound and the door will unlock.

Remove damp clothes from the washer immediately. Check under the door seal for small items.

SPIN SPEED

The washer drum spins at up to 1,320 RPM. This reduces drying time and saves energy.

Press the SPIN SPEED button to select the maximum spin speed. Some fabrics, such as delicates, require a slower spin speed.

The Drain & Spin cycle:

The Spin Speed button also activates the Drain & Spin cycle to drain the tub and spin clothes; for example, if you want to remove clothes before the cycle has ended.

To activate the DRAIN & SPIN cycle:

Press the ON/OFF button to turn on the washer.

Press the SPIN SPEED button. Select the desired spin speed.

NOTE: If NO SPIN is selected, the washer will drain only.

Press the START/PAUSE button.

To Use the SteamFresh Cycle:

Turn on the washer and turn the cycle selector knob to select the SteamFresh cycle.

Load up to 5 items and close the door. NOTE: If there is any moisture inside the

drum, such as from a previous wash cycle, wipe the drum dry with a towel before adding clothes.

Press the STEAM button until the correct number of items is shown in the display. No other options need to be set.

Press the START/PAUSE button to start the cycle.

After the SteamFresh cycle is complete, the washer will tumble the clothes for up to 30 minutes to prevent rewrinkling.

After removing clothes from the SteamFresh cycle, they may feel slightly damp. Place clothes on a hanger for at least 10 minutes to allow them to dry.

• The SteamFresh cycle is not recommended for use with 100% cotton clothing.

• Remove stains from clothing before using the SteamFresh cycle; the high heat could cause stains to set permanently.

• Do not use SteamFresh with the following items: wool, blankets, leather jackets, silk, wet clothes, lingerie, foam products, or electric blankets.

• Best results are achieved when articles are of similar size and fabric type. Do not overload.

H O W TO U S E

CYCLE SETTING BUTTONS

Each cycle has preset settings that are selected automatically. You may also customize the settings using the cycle setting buttons. Press the button for that option to view and select other settings.

The washer automatically adjusts the water level for the type and size of wash load for best results and maximum efficiency. It may seem there is no water inside the drum in some cycles, but this is normal.

NOTE: To protect your garments, not every wash/ rinse temperature, spin speed, soil level, or option is available with every cycle. See the Cycle Guide for details.

SOIL LEVEL

Adjusts the selected cycle to allow more time for heavily soiled clothes or less time for lightly soiled clothes.

WASH/RINSE

Selects the wash and rinse temperature combination for the selected cycle. Press the WASH/RINSE button repeatedly to scroll through available settings.

• Your washer features a heating element to boost the hot water temperature for Extra Hot settings. This provides improved wash performance at normal water heater settings.

• Select the water temperature suitable for the type of load you are washing. Follow the fabric care label for best results.

• Warm rinses leave the loads drier than cold rinses. Warm rinses can increase wrinkling.

• In cold climates, a warm rinse makes the load more comfortable to handle.

• Cold rinses use less energy.

H O W TO U S E

Using the SteamFresh™ Cycle

SteamFresh uses the power of steam alone to quickly reduce wrinkles and odor in fabrics. It brings new life to wrinkled clothes that have been stored for an extended time and makes heavily wrinkled clothes easier to iron. SteamFresh can also be used to help reduce odors in fabrics.

STEAM CYCLES

STEAM cycles include the Sanitary, Bulky/Large, Perm. Press, Cotton/ Normal, and ALLERGIENETM cycles.

Adding the Steam option to these cycles provides superior cleaning performance while reducing energy and water consumption. By using a hot steam spray from above and cooler water below, fabrics get the cleaning benefits of a super hot wash, without the energy usage or potential damage to fabrics.

To Add STEAM to a Standard Cycle:

Turn on the washer and turn the cycle selector knob to select a cycle with the STEAM option.

Press the STEAM button. The washer will automatically adjust the cycle settings.

Set any other desired options. Press the START/PAUSE button to start the

cycle. The washer will start automatically.

CAUTION: Do not touch the door during steam cycles. The door surface can become very hot. Allow the door lock to release before opening the door.

Do not attempt to override the door lock mechanism or reach into the washer during a steam cycle. Steam can cause severe burns.

IMPORTANT NOTES ABOUT STEAM CYCLES:

• Steam may not be clearly visible during the

steam cycles. This is normal. Too much steam could damage clothing.

• Do not use steam with delicate fabrics such as

wool, silk, or easily discolored fabrics.

• Do not touch the door.

+ 25 hidden pages