LG WD-13060FD User manual [en,th]
OWNER’S MANUAL
WASHING MACHINE
WD-13060FD
P/No.: MFL48165943
www.lg.com
Please read this manual carefully before operating
your washing machine and retain it for future reference.
2
ontents
C
Contents....................................2
Product feature.........................3
Warnings
Important safety instructions .................4
Save these instructions.........................4
Specification.............................5
Installation
Transit bolts ..........................................6
Removing transit bolts ..........................6
Installation place requirement ...............7
Positioning ............................................7
Electrical connection .............................8
Connecting water supply hose..............9
Installation of drain hose .....................11
Level adjustment.................................12
Care before washing
Before the first washing ......................14
Caring before washing ........................14
Adding detergent
Adding detergent and fabric softener..15
How to use washer
Washing program table.......................17
Control Panel ......................................18
Additional program..............................19
- Power..............................................19
- Program ..........................................19
- Start/Pause .....................................20
- Door Lock .......................................20
- Detecting.........................................20
- Wash...............................................20
- Child Lock .......................................21
- Rinse...............................................21
- Spin.................................................22
- Water Temperature.........................22
- Add Load ........................................23
- Time Delay......................................23
- Tub Clean .......................................24
- Display ............................................25
Thank you for buying a LG Fully
Automatic Washing Machine.
Please read your owner’s manual
carefully, it provides instruction on safe
installation, use and maintenance.
Retain it for future reference.
Record the model and serial number of
your washing machine.
Model No.
Serial No.
Date of Purchase
Maintenance
The water inlet filter.............................26
The drain pump filter ...........................27
Dispenser drawer................................28
The drawer recess ..............................28
The washing drum ..............................28
The water circulation nozzle & steam
nozzle..................................................29
Cleaning your washer .........................29
Winterizing instructions .......................29
Troubleshooting guide
Diagnosing problems ..........................30
Error messages...................................33
Using SMARTDIAGNOSIS™..............34
Terms of warranty ..................35
3
roduct Feature
P
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
6 Motion
Washer is able to perform various drum actions or a combination of
different actions depending on the wash program selected.
Combined with a controlled spin speed and the ability of the drum to
rotate both left and right, the wash performance of the machine is greatly
improved, giving you perfect results every time.
Water Circulation
Sprays detergent solution and water onto the load over and over.
Clothes are soaked more quickly and thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower
during rinse cycle. The water circulation system uses both water and
detergent more efficiently.
Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
Embossing drum & waved lifter
Embossing drum enhances the washing performance and reduces
clothes damage.The waved lifter spray and help clothes to enhance
washing performance during the washing cycle.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
Built-in Heater
Internal heater helps to maintain water temperature at its optimum level
for selected cycles.
Child Lock
The Child lock prevents children from pressing any button to change the
settings during operation.
추가선택, 예약,
4
arnings
W
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
!
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE
WARNING!
❊ Do not push down the door excessively, when washer door open.
This could topple over the washer.
• Before installation, check exterior damages. If it has,
do not install.
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance instructions
or published user-repair instructions that you
understand and have the skills to carry out.
• Keep the area underneath and around your
appliances free of combustible materials such as lint,
paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance is
used by or near children. Do not allow children to
play on, with, or inside this or any other appliance.
• Keep small animals away from the appliance.
• Do not leave the washer door open.
An open door could entice children to hang on the
door or crawl inside the washer.
• Never reach into washer while it is moving. Wait until
the drum has completely stopped.
• The laundry process can reduce the flame retardant
of fabrics.
• To avoid such a result, carefully follow the garment
manufacturer’s wash and care instructions.
• Do not wash or dry articles that have been cleaned
in, washed in, soaked in, or spotted with combustible
or explosive substances (such as wax, oil, paint,
gasoline, degreasers, dry-cleaning solvents,
kerosene, etc.) which may ignite or explode. Oil may
remain in the tub after a whole cycle resulting in fire
during drying. So, do not load oiled clothes.
• Do not slam the washer door closed or try to force
the door open when locked. This could result in
damage to the washer.
• When the machine runs high temperature, the front
door may be very hot. Don’t touch it.
• To minimize the possibility of electric shock, unplug
this appliance from the power supply or disconnect
the washer at the household distribution panel by
removing the fuse or switching off the circuit breaker
before attempting any maintenance or cleaning.
• When unplugging power cord, do not pull out by
grasping the cord. Otherwise, the power cord may
be damaged.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled, or
has missing or broken parts, including a damaged
cord or plug.
• Before discarding an old machine unplug it. Render
the plug useless. Cut off the cable directly behind the
appliance to prevent misuse.
• When a product was under water, Please call
service center. The risk of electric shock and fire.
• Do not use water temperature higher than 95 °C with
this Washing Machine.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord
having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer,
follow basic precautions, including the following:
SAVE THESE INSTRUCTIONS
WARNING : Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
5
pecification
S
Name : Front loading washing machine
Power supply : 220 V~, 50 Hz
Size : 645 mm(W) x 770 mm(D) x 940 mm(H)
Weight : 77 kg
Wash capacity (Max. Watt) : 13 kg (1900 W)
Spin speed : Extra Low / Low / Medium / High / Extra High
Water consumption : 156
l
Permissible water pressure : 1.0 - 10.0 kgf / cm2(100 - 1000 kPa)
❋ The appearance and specifications may be varied without notice to improve the units quality.
❋ Specifications subject to change by manufacturer.
Accessories
Drum
Drain Pump Filter
Drain Plug
Door
Adjustable Feet
Drain Hose
Control Panel
Lower cover cap
Shipping Bolts
Power Plug
• If the supply cord is damaged,
it must be replaced by the
manufacturer or its authorized
service technician in order to
avoid a hazard.
Inlet Hose
Dispenser
Inlet hose (1EA) Spanner
6
nstallation
I
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
• If they are not removed, it may cause
heavy vibration, noise and malfunction.
3. Take out the 4 bolts along with the
rubber bungs by slightly twisting the
bung. Keep the 4 bolts and the spanner
for future use.
• Whenever the appliance is transported,
the transit bolts must be refitted.
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be
removed before using the washer.
When unpacking the base, be sure to
remove the additional packing support
in the middle of the base packing.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
Transit bolts
Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on
a carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin, pay particular attention to keeping the appliance and its surroundings in clean
condition at all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the
appliance guarantee.
Removing transit bolts
Washer
Base Packing
Packing Support
7
nstallation
I
Level floor :
Allowable slope under entire washer is 1°
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear / 2cm : right & left side)
Do not place or store laundry products on top of
washer at any times.
They can damage the finish or controls.
Installation place requirement
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Before placing the washer on tiles, apply a rubber mat under the feet.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar
materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an
insulating covered with aluminum foil on the side facing the cooker or stove,must be inserted
between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the
event of a breakdown.
• With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the
appliance is stable, and a clearance of approximately 20mm is left between the top of the washer
and the underside of the work-top.
• The installation instructions shall state that the openings must not be obstructed by a carpet if it
has ventilation openings in the base.
Washer
Drain Hose
Laundry
Tub
approx.
2cm
8
nstallation
I
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or
similarly qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the
washing machine at room temperature for a few hours before putting it into operation.
Electrical connection
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
If this appliance is supplied from a cord extension set or electrical portable outlet device, the cord
extension set or electrical portable outlet device must be positioned so that it is not subject to
splashing or ingress of moisture.
CAUTION
This appliance is not intended for use by young children or infirm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.
CAUTION
9
nstallation
I
1. Unscrew the adapter ring plate and the 4
adapter retaining screws.
2. Push the adapter onto the end of the tap
so that the rubber seal forms a watertight
connection. Tighten the adapter ring plate
and the 4 screws.
3. Push the water supply hose vertically
upwards so that the rubber packing within
the hose can adhere completely to the
tap and then tighten it by screwing it to
the right.
• Water supply pressure must be between 100 kPa and 1000 kPa (1.0 ~ 10.0 kgf / cm
2
).
• Do not strip or crossthread when connecting inlet hose to the valve.
• If the water supply pressure is more than 1000 kPa, a decompression device should be
installed.
• Periodically check the condition of the hose and replace the hose if necessary.
Type-A : Connecting Screw-type hose to tap with thread
• Screw the hose connector onto water
supply tap.
■ Connecting water supply hose
▶▶
Step1 : Check rubber seal inlet hose
▶▶
Step2 : Connect hose to water tap
• Two rubber seals are supplied with the
water inlet hoses.
They are used for preventing water leaks.
Make sure the connection to taps is
sufficiently tight.
Upper
connector
Rubber
packing
Plate
Water supply
hose
Fixing screw
Hose
connector
Rubber
seal
Type-B : Connecting Screw-type hose to tap without thread
10
nstallation
I
1. Unscrew the adapter ring plate and
the 4 adapter retaining screws.
2. Remove the guide plate if the tap is
too large to fit the adapter.
3. Push the adapter onto the end of
the tap so that the rubber seal forms
a watertight connection.
Tighten the adapter ring plate and
the 4 screws.
4. Pull the connector latch plate down,
push the inlet hose onto the adapter,
and release the connector latch plate.
Make sure the adapter locks into place.
After completing connection, if water leaks from the hose, repeat the same steps.
Use the most conventional type of faucet for water supply. In case the faucet is square
or too big, remove the spacing ring before inserting the faucet into the adaptor.
Use the horizontal tap
Horizontal tap Extension tap Square tap
Ring plate
Guide plate
Latch plate
Type-C : Connecting one touch type hose to tap without thread
▶▶
Step3: Connect hose to washer
• Make sure that there are no kinks in the
hose and that they are not crushed.
▶▶
When your washer has two valves.
• The Inlet hose which has red connector is
for the hot water tap.
• If the washer has two valves, the energy is
saved by using hot valve.
After connecting inlet hose to
water tap, turn on the water taps
to flush out foreign substances
(dirt, sand or sawdust) in the
water lines. Let water drain into a
bucket, and check the water
temperature.
11
nstallation
I
Installation of drain hose
• The drain hose should not be placed higher
than 100 cm above the floor. Water in the
washer does not drain or drains slowly.
• Proper securing of the drain hose will protect
the floor from damage due to water leakage.
• When the drain hose is too long, do not force
back into the washer. This will cause
abnormal noise, malfunction, and water
leakage.
• When installing the drain hose to a sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to water
leakage should the drain hose become
loose.
This equipment is not designed for maritime use or for use mobile installations such as
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the Plug.
Disable the door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of
suffocation ! Keep all packaging well away from children
about 100 cm
about 100 cm
Laundry tub
Hose
Retainer
Tie
strap
max. 100cm
min. 60cm
max. 100cm
min. 60cm
about 105 cm
about 105 cm
max. 100 cm
max. 100 cm
min. 60 cm
min. 60 cm
about 145 cm
about 145 cm
12
nstallation
I
In case of auto leveling foot
The right rear foot of the washing machine is an auto leveling foot.
Unlike with the adjustable feet, adjusting the auto leveling foot bolt
may cause noise or vibration.
❊ Check the auto leveling foot’s state
Case1. Floating from floor
• Raising the front left adjustable foot will press the
auto leveling foot to the floor.
Case2. Auto leveling foot fully pressed
• Raising the adjustable feet at the right front and left
back corners will release the auto leveling foot.
Level adjustment
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably
in a corner of the room.
2. If the floor is uneven, adjust the adjustable feet as required.
(do not insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
※※
After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate
diagonally, the machine should not move up and down at all. (Please,
check both of two directions)
If machine rocks when pushing the machine top plate diagonally,
adjust the feet again.
NOTE
Timber or suspended type flooring may contribute to
excessive vibration and unblance errors.
NOTE
In the case that the washing machine is installed on a raised
platform, it must be securely fastened in order
to eliminate the risk that it might fall off.
Adjustable
feet
Adjustable
feet
13
nstallation
I
Concrete floors
Wooden floors (Suspended floors)
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into
70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)
※※
Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each
foot, at least 15mm thick under the washer, secured to at least 2 floor
beams with screws.
• If possible install the washer in one of the corners of the room, where
the floor is more stable.
※※
Insert the rubber cups to reduce vibration.
※※
Rubber cups ( p/no. 4620ER4002A) can be purchased from the LG spare parts department.
Important!
• Proper placement and levelling of the washer ensures long, regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
※
It can be purchased from
hardware suppliers.
Rubber Cup
14
are before washing
C
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
2. Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can
occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly
soiled one.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil.
Color (White, Lights, Darks) Separate white fabrics from colored fabrics.
Lint (Lint producers, Collectors) Wash lint producers and lint collectors
separately.
3. Caring before loading
Caring before washing
Before the first washing
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing.
This will remove residues from the drum that may have been left during manufacturing.
• Check all pockets to make sure that they are
empty. Items such as nails, hair clip,
matches, pens, coins and keys can damage
both your washer and your clothes.
• Pre treat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help shift dirt.
• Close zippers, hooks and strings to make
sure that these items don’t snag on other
clothes.
• Check the folds of the flexible gasket (gray)
and remove any small articles,if any.
• Check inside of the drum and remove any left
items in it for next wash cycle.
• Remove any clothing or items on the flexible
gasket to prevent clothing and the gasket
damages.
15
dding detergent
A
• Main wash only
➔
• Pre Wash + Main Wash
➔
• Do not exceed the maximum fill line. Close
the dispenser drawer slowly. Overfilling can
cause early dispensing of the fabric softener
which could stain clothes.
• Do not leave the fabric softener in the
detergent drawer for more than 2 days.
(Fabric softener could harden)
• Softener will automatically be added during
the last rinse cycle.
• Do not open the drawer when water is
supplied.
• Solvents(benzene, etc) are not allowable.
1. The Dispenser Drawer
2. Adding Fabric Softener
Adding detergent and fabric softener
Do not pour fabric softener
directly on the cloths
NOTE
Detergent for
main wash
Fabric
softener
Detergent for
pre wash
16
dding detergent
A
• The detergent should be used according to the
instruction of the detergent manufacture.
• If too much detergent is used, too many suds
can occur and this will decrease the washing
result or cause heavy load to the motor.
• Use powder detergent only for the front
loading washer.
❇
If suds occur too much, pleas reduce the
detergent amount.
• Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid oversudsing.
4. Water softener
• A water softener, such as Anti limescale
(Clagon) can be used to cut down on the
use of detergent in extremely hard water
areas. Dispense according to the amount
specified on the packaging.
First add detergent and then the water
softener.
• Use the quantity of detergent as for soft
water.
❋
Tips
Full load : according to
manufacturer’s recommendation.
Part load : 3/4 of the normal
amount.
Minimum load : 1/2 of full load.
• Detergent is flushed from the dispenser
at the beginning of the cycle.
1) Open the door and Tablets into the
drum.
3. Detergent dosage
5. Using the Tablets
2) Load the laundry into the drum.
3) Close the door.
17
ow to use washer
H
•
Recommended courses according to the laundry type.
Cotton
Color fast garments (shirts, night
dresses, pajamas...)and lightly soiled
white cotton (underwear...)
Pre Wash,
Intensive, Normal,
Light, Shoes Wash,
No Wash,
Time Delay
40˚C
(Cold, 60˚C)
Rating
Rating
Sports Wear
Normal, No Wash,
Time Delay
40˚C
(Cold)
Dark Wash
This cycle is suitable for lightly soiled
clothing. Use this cycle to save energy,
by using cold water while ensuring proper
washing.
Normal, No Wash,
Time Delay
40˚C
(Cold)
Cold Wash
Pre Wash,
Intensive, Normal,
Light, No Wash,
Time Delay
Cold
Wool
Normal, No Wash,
Time Delay
Normal, Light,
No Wash,
Time Delay
Time delay,
Pre wash, No wash
Normal, Intensive,
Pre Wash,
Time Delay,
No Wash, Light
40˚C
(Cold)
Duvet
Baby Care
Silent
Normal, No Wash,
Time Delay
Pre Wash,
Intensive, Normal,
No Wash,
Time Delay
Sanitary
Heavy Duty
Cold
(40˚C)
95˚C
40˚C
(60˚C, Cold)
60˚C
(40˚C)
60˚C
This cycle is suitable for sports wear
such as jogging clothes and running
wear.
Use this cycle to wash “multi-color”
clothes to maintain their color
Enable to wash wool fabrics. (Please use
detergent for machinewashable woolens).
This cycle is for large items such as bed
cover, pillows, sofa covers, etc.
Lightly soiled baby wear
Color fast garments (Shirts, nightdresses,
pajamas, etc.) and lightly soiled white
cotton (underwear).
Heavily soiled underwear, work clothes,
diapers, etc
Heavily soiled cotton fabrics
Maximum
Load
Additional
Option
Proper Temp.
(Option)
Fabric Type
Program
❋ Notes : Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for
garment care.
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine
washable Woolmark products provided that the products are washed according to the instructions
on the garment label and those issued by the manufacturer of this washing machine M0806.
Washing program table
Rinse+Spin
Rinse and Spin
Time Delay
–
–
Normal, No Wash,
Time Delay
Speed Wash
40˚C
(Cold)
Lightly soiled clothing and small loads
Less than
5.0kg
Less than
5.0kg
Less than
3.0kg
Less than
3.0kg
Less than
5.0kg
Less than
5.0kg
Less than
4.0kg
1 king size
(9 Tog)
Less than
5.0kg
18
ow to use washer
H
• Press the Power( ) button to start.
• Press the Start/Pause( ) button.
• Initial condition
- Rinse : 3
- Water temperature : 40°C
- Spin : High
- Program : Cotton
• Press the Power( ) button to turn the
washer on.
• Select the desired cycle with the program
dial and if required, make any changes to
the washing conditions by pressing the
buttons accordingly.
For selecting the each conditions, please refer
to the Page19~page25.
• Press the Start/Pause button to
commence the cycle.
1. Cotton automatically
selected upon power on.
2. Manual Selecting
■ Control panel
19
ow to use washer
H
ProgramPower
• Press the Power( ) button to turn power
on and off.
• To cancel the Time Delay function, the
Power( ) button must be pressed.
• When the Power( ) button is pressed, the
washer is ready for Cotton program. And the
other initial conditions as follows.
• So, if you want to advance into the washing
cycle without changing the program, just
press Start/Pause( ) button and then the
washer will proceed.
■
Initial program
- Cotton Program / Rinse:3 / 40°C / High
(1)Button: Power
(2)Dial: Program
(3)Button: Start/Pause
(4)Button: Wash
(5)Child Lock
(6)Button: Rinse
(7)Button: Spin
(8)Button: Temperature
(9)Button: Add Load
(10)Button: Time Delay
(11)Button: Tub Clean
(12)Button: Option
• 12 programs are available according to the
laundry type.
• Dial lamp will light up to indicate selected
program.
• When Start/Pause( ) button is pressed,
the Cotton program is automatically selected.
- By turning the Program dial, the program is
Selected in order of “Cotton – Sports Wear –
Dark Wash – Cold Wash – Wool – Duvet –
Rinse+Spin – Speed Wash – Baby Care –
Silent – Sanitary – Heavy Duty ”.
For information regarding laundry type for
each program, please refer to page 17.
1. Power
2. Initial Program
(1) (3) (4) (6) (7)
(12)(11)(10)(9)(8)
(5)(2)
SMARTDIAGNOSIS™ function is
available only for the products with
a SMARTDIAGNOSIS™ mark.
20
ow to use washer
H
WashStart/Pause
• This Start/Pause button is used to start
wash cycle or pause the wash cycle.
• If temporary stop of wash cycle is needed,
press “Start/Pause” button.
• When in Pause, the power is turned off
automatically after 4 minutes.
NB. The door will not open before 1 to 2
minutes when Pause is selected, or at
the end of the wash cycle.
1. Start
• Use this option for loads that need
pretreatment. This adds 16 minutes of pre
washing before draining.
- When using Pre Wash option, do not use a
liquid detergent for the main wash.
Use powder for the main wash.
1. Pre Wash
• If the laundry is heavily soiled “Intensive”
option is effective.
• By selecting the Intensive option, the wash
time may be extended, depending on the
program selected.
• To use this option select the Intensive option
once before the wash programe is started.
2. Intensive
• This option is automatically selected in
every course except for Rinse+Spin.
3. Normal
• This cycle is suitable for lightly soiled clothing.
4. Light
• Use this option when you want to wash
slippers or shoes.
※※
Depending on the usage condition, steam
could not be operated.
5. Shoes Wash
2. Pause
• Lights whenever the door of the washer is
locked.
• The door can be unlocked by pressing the
Start/Pause button to stop the washer.
• The door can be opened after a short delay.
Door Lock
• While the "Detecting" is shown in the display
the machine rotates slowly and detects how
many laundries are loaded in the drum.
It will take a few seconds.
Detecting
21
ow to use washer
H
Rinse
• By pressing the Rinse button, the Rinse
type can be selected.
• Duvet, Silent, Baby care perform 4 Rinses.
• Cotton, Sports Wear, Dark Wash,
Cold Wash, Wool, Sanitary, Heavy Duty
perform 3 Rinses.
• Speed Wash performs 2 Rinses.
• Rinse+Spin performs 1 Rinse.
The matching indicator lamp will light up for
identification.
Child Lock
Use this option to prevent unwanted use of
the washer or to keep cycle settings from
being changed while the washer is operating.
• Child Lock can be set by pressing and
holding the Wash and Rinse button
simultaneously. (About three seconds)
• When CHILD LOCK is set, the Child Lock
indicator will appear and all buttons are disabled
except the POWER button.
• To deactivate Child Lock system, press and
hold the Wash and Rinse button
simultaneously again. (About three seconds)
• To change to the desired program, whilst in
Child Lock mode.
1. Press and hold both Wash and Rinse button
together once again. (About three seconds)
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
• CHILD LOCK lasts after the end of cycle.
If you want to deactivate this function, Press
and hold the Wash and Rinse button
simultaneously for 3 seconds.
Change
the desired
program
NOTE
Loading...