LG W2286LV Users manual

Order Number : GETEC-C1-09-097 FCC Class B Certification Test Report Number : GETEC-E3-09-045 Page 1 / 1

APPENDIX H

: USER’S MANUAL

EUT Type: LCD Monitor

FCC ID.: BEJW2286LV

User’s Guide

W2286L W2486L

Make sure to read the Important Precautions before using the

product. Keep the User's Guide(CD) in an accessible place for future reference.

See the label attached on the product and give the information to

your dealer when you ask for service.

Important Precautions

This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation.

Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power cords and broken plugs. They may result in a shock or fire hazard. Call your service technician for replacement.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

Do not Open the Display:

There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured. Use only a stand recommended by the manufacturer. Do not drop an object on or apply impact to the product. Do not throw any toys or objects on the product screen. It can cause injury to human, problem to product and damage the display.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period of time. Never leave the display ON when leaving the house. Keep children from dropping or pushing objects into the display's cabinet openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this display. When the display is to be left unattended for an extended period of time, unplug it from the wall outlet. In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous. It can cause electric shock.

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.

Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc. Place the display in a built-in enclosure unless proper ventilation is provided. Cover the openings with cloth or other material. Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen. However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for your LCD display. If used under any mode except the recommended resolution, some scaled or processed images may appear on the screen. However, this is characteristic of the fixed-resolution LCD panel.

Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product.

Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen.

Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair.

Avoid high temperatures and humidity.

Important Precautions

On Cleaning

Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

When cleaning the product, unplug the power cord and scrub gently with a soft

cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benzene, paint thinners or alcohol)

Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;

wipe in one direction only. Too much moisture may cause staining.

On Repacking

Do not throw away the carton and packing materials. They make an ideal container in which to transport the unit. When shipping the unit to another location, repack it in its original material.

On Disposal (Only, Hg lamp used LCD Monitor)

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of

your local authority.

Accessories

!!! Thank for selecting LGE products !!!

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.

User's Guide/Cards

DVI-D Signal Cable

(This feature is not available

in all countries.)

N E P O

Cable Holder

Power Cord

15-pin D-Sub Signal Cable

(To set it up, this signal cable may

be attached to this product before

shipping out.)

AC-DC adapter

NOTE

This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI cable) with ferrite cores to maintain standard compliance for the product.

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Connecting and Disassembling the stand

1. Place the monitor face down on the soft cloth.

2. Assemble the Stand Base into the Stand Body in the correct direction.

Make sure you push the Stand Base until the end.

Stand Body

Good Connection

Stand Base

The Stand Base may fall and get damaged or cause injury.

Bad Connection

Connecting the Display

3. Turn the screw to the right to fix the Stand Body to the Stand Base.

Screw

Turn the screw by using the screw handle.

4. Then fold the screw handle flat. 5. Once assembled take the monitor up

carefully and face the front side.

6. To disconnect the Stand Base from the Stand Body, unfold the screw handle and

turn it to the left.

IMPORTANT

This picture depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or cause injury.

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Positioning your display

After installation, adjust the angle as shown below.

1. Adjust the position of the panel in various ways for maximum comfort.

Tilt Range : -2˚~15˚

-2

Do not touch or press the screen when adjusting the angle of the monitor.

When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s).

ERGONOMIC

It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees.

Connecting the Display

Connecting with the PC/

Before setting up the monitor, ensure that the power to the monitor, the computer system,

AV equipment

and other attached devices is turned off.

Connect signal input cable , then tighten the screw of the signal cable.

Connect the power cord to the AC-DC adapter and insert the plug in a wall outlet.

Connect DVI-D(Digital signal) Cable

Connect D-sub(Analog signal) Cable

Connect HDMI Cable (HDMI1, HDMI2)

NOTE

This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown.

Headphone output

Headphones

/ Earphones

Varies according to model.

Wall-outlet type

AV equipment

Video,Video Game Console)

* HDMI is optimized on the AV equipment. * Not supported PC.

When using a D-Sub signal input cable connector for Macintosh

Mac adapter : For Apple Macintosh use, a separate plug adapter

is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector.

(Set-Top Box, DVD,

DVI-D (This feature is not available in all countries.)

Connecting the Display

NE P O

4. Gather the cables together and use the Cable Holder to arrange them as shown in

the picture.

Cable Holder

5. Press the Power Button ( ) on the front panel to turn the power on. When monitor

power is turned on, the 'Self Image Setting Function' is executed automatically.

(Only Analog Mode)

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display

settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO/SET function button to improve resolution.

Control Panel Functions

1 2 3 5 74 86

Front Panel Controls

Button

MENU Button

Use this button to enter CINEMA MODE, AUTO BRIGHT, TIME CONTROL, LIVE SENSOR or SMART menus.

For more information, refer to page 16.

Use this button to move to EZ ZOOMING, 4:3 IN WIDE and PHOTO EFFECT for D-SUB/DVI signal input.

Use this button to move to 4:3 IN WIDE, PHOTO EFFECT and VOLUME for HDMI signal input.

For more information, refer to page 17.

Use this button to enter or exit the On Screen Display.

OSD LOCKED/UNLOCKED

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.

Control Panel Functions

DSUB DVI HDMI1 HDMI2

INPUT

Buttons

(SOURCE Hot key)

Use these buttons to select or adjust functions in the On Screen Display.

Use this function to select optimal image conditions in accordance with the surrounding environment (Brightness, Image type). For more information, refer to page 19.

When two or more input signals are connected, you can select the input signal (DSUB/DVI/HDMI1/HDMI2) you want. If only DSUB or DVI input signal is connected, it is automatically detected.

If either HDMI1 or HDMI2 input signal is connected, you need to select the input signal you want from the INPUT menu. The default input signal is DSUB.

AUTO/SET Button

Use this button to enter a selection in the On Screen Display.

AUTO IMAGE ADJUSTMENT

When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD).(Only Analog Mode) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).

The best display mode is

W2286L : 1680 x 1050 W2486L : 1920 x 1080

Control Panel Functions

Power Button

Power Indicator

Light Sensor

Use this button to turn the display on or off.

The power indicator stays red if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking red.

This is the sensor to measure the external brightness. Makes the screen brighter or darker, depending on the surrounding brightness, when AUTO BRIGHT is set to ON. The default setting is OFF.

+ 31 hidden pages