LG W1946SW, W1946TW Users manual

User’s Guide

W1946T W2046T W2246T W2346T W1946S W2046S W2246S W2346S

Make sure to read Safety Precautions before using this product.

Keep the User's Guide (CD) in an accessible place for future reference.

See the attached label on the unit and show this information to your dealer

when asking for service.

Safety Precautions

Please read these safety precautions carefully before using the product.

Warning

Failure to follow those warnings may result in death, serious injury or damage to the product or other property.

Electrical Power Related Precautions

Warning

Use only the power cord supplied with the unit or another manufacturer authorized cord.

- Failure to do so may result in fire or electrical shock or damage to the product.

Use only a properly grounded plug and receptacle.

- If you do not you may be electrocuted or injured. Or the product might be damaged.

Do not use a damaged or loose plug.

- This may cause electrical shock or fire.

Operate the display only from a power source(i.e. voltage) indicated in the product specification.

- Otherwise the product can be damaged, fire can occur or you may be electrocuted. If you are not sure what type of power supply you have, consult a certified electrician.

In the presence of thunder and lightning, never touch the power cord and signal cable because it can be very dangerous.

- It can cause electric shock.

Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet. Use a power bar with a grounding terminal designed for exclusive use with the computer.

- A fire can break out due to overheating.

Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off before plugging in the cord.

- You may be electrocuted due to excess moisture.

If you don’t intend to use the product for a long time, unplug the power cable from the product.

- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.

Insert the power plug firm so it cannot come loose.

- A loose connect can cause fire.

Hold the plug when pulling out the power cable. Do not pull the plug out by the wire. Do not bend the power cord with excessive force or put heavy objects on the power cord.

- The power line can be damaged, which may cause electric shock or fire.

Do not insert conductive material (ea. metal chopstick) into the product opening into one end of the power cable while the other end is plugged in. Additionally, do not touch the power cable right after plugging into the wall input terminal.

- You may be electrocuted.

The power supply cord is used as the main disconnection device. Ensure that the socket-outlet shall be installed near the equipment and shall be easily accessible.

Do not unplug the power cord while the product is in use.

- Electrical shock can damage the product.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if the unit is turned off.

Safety Precautions

Precautions in installing the Product

Warning

Keep away from heat sources like electrical heaters, curdles or other open flames.

- Electrical shock, fire, malfunction or deformation may occur.

Keep the packing anti-moisture material or vinyl packing out of the reach of children.

- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.

Do not put heavy objects on the product on sit upon it.

- If the product collapses or is dropped, you may be injured. Children must pay particular attention.

Do not leave the power or signal cable when someone can trip over it.

- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.

Install the product in a neat and dry place. Do not use near water.

- Dust or moisture can cause electrical shock, fire or product damage.

Do not add accessory that have not been designed for this display.

If you smell smoke or other odors or hear a strange sound from the product unplug the power cord and contact the service center.

- If you continue to use without taking proper measures, electrical shock or fire can occur.

If you dropped the product or the case is broken, turn off the product and unplug the power cord.

- If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service center.

Do not drop an object on or apply impact to the product. Do not throw any toys or objects at the product.

- It can cause injury to humans, problems to the product and damage the display.

Keep out of reach of children and do not place toys near the product.

Make sure the product ventilation hole is not blocked. Install the product more than 10cm from the wall.

- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat build-up.

Do not cover the product with cloth or other material (eg. plastic) while plugged in.

- The product can be deformed or fire can break out due to internal overheating inside the product.

Place the product on a flat and stable surface that is large enough to support the product.

- If the product is dropped, you may be injured or the product may be broken.

Install the product where no Electromagnetic Interference occurs.

Keep the product away from direct sunlight.

- The product can be damaged.

Do not place the product on the floor.

- Small Children and others may trip over it.

Precautions in Moving the Product

Warning

Make sure to turn off the product.

- You may be electrocuted or the product can be damaged.

Make sure to remove all cables before moving the product.

- You may be electrocuted or the product can be damaged.

When lifting or moving the product, do not hold it upside down while holding only the stand.

- This may cause the product to fall resulting in damage or injury.

Do not shock the product when moving it.

- You may be electrocuted or the product can be damaged.

Safety Precautions

Make sure the panel faces forward and hold it with both hands to move.

- If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair.

Do not place the product face down.

- This may damage the TFT-LCD screen.

Precautions in Using/Cleaning the Product

Warning

Do not attempt to disassemble, repair or modify the product yourself.

- Fire or electric shock can occur.

- Contact the service center for repair.

When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth. Or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benzene, paint thinners or alcohol)

Keep the product away from water.

- Fire or electric shock accident can occur.

Avoid high temperatures and humidity.

Do not put or store flammable substances near the product.

- There is a danger of explosion or fire.

Keep the product clean at all times.

Take a comfortable and natural position when working with a product to relax the muscles.

Take a regular break when working with a product for a long time.

Do not press on the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it.

Keep proper distance from the product and rest from time-to-time.

- Your vision may be impaired if you look at the product too closely or fpr too long.

Set the appropriate resolution by referring to the User’s Guide.

- Your vision can be impaired.

Keep small accessories out of the reach of children.

Leaving a fixed image on the screen for a long time may cause damage to the screen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product.

Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.

Safety Precautions

NOTE

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.Such modefications could void the user's authority to operate the equipment.

This epuipment has been tested and found to comply with the limits for a class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and the receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Accessories

!!! Thank for selecting LGE products !!!

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.

User's Guide/Cards

DVI-D Signal Cable

(This feature is not available

in all countries.)

NOTE

This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product.

Power Cord

15-pin D-Sub Signal Cable

(To set it up, this signal cable may

be attached to this product before

shipping out.)

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Connecting the stand

Place the monitor with its front facing downward on a soft cloth.

Assemble the Stand Body into the

product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”.

Stand Body

Hinge Body

Stand Body

Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.

Stand Base

Tie down the base lock to perpendicularity direction.

Once assembled take the monitor up carefully and face the front side

Important

This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.

Connecting the Display

Disassembling the stand

Put a cushion or soft cloth on aflat surface.

Change your lock on the product as it follows and turn it in the arrow direction.

If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it.

Place the monitor face Down on the cushion or soft cloth.

Connecting the Display

Pull out the Stand to remove.

Pushing the PUSH button, Take the stand base from stand body.

Good Position Bad Position

Warning:

You can hurt your finger.

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Positioning your display

-After installation, adjust the angle as shown below.

Adjust the position of the panel in various ways for maximum comfort.

Tilt Range : -5˚~15˚

Do not touch or press the screen when adjusting the angle of the monitor.

When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s).

ERGONOMIC

It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees.

Connecting the Display

Connecting with the PC

Before setting up the monitor, ensure that the power to the monitor, the computer

system, and other attached devices is turned off. Connect signal input cable and power cord in order, then tighten the screw

of the signal cable.

Connect DVI-D(Digital signal) Cable

Connect D-sub(Analog signal) Cable

NOTE

This is a simplified representation of the rear view.

This rear view represents a general model; your display may differ from the view as shown.

Varies according to model.

W1946T/W2046T/W2246T/W2346T

When using a D-Sub signal input cable connector for Macintosh

Mac adapter : For Apple Macintosh use, a

separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector.

Wall-outlet type

DVI-D (This feature is not available in all countries.)

Press the power button on the front panel to turn the power on. When monitor power is

turned on, the 'Self Image Setting Function' is executed automatically.

(Only Analog Mode)

Power Button

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display

settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution.

Connecting the Display

Connecting with the PC

Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.

Connect signal input cable and power cord in order, then tighten the screw of the signal cable.

Connect D-sub(Analog signal) Cable

NOTE

This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown.

Varies according to model.

W1946S/W2046S/W2246S/W2346S

When using a D-Sub signal input cable connector for Macintosh

Mac adapter : For Apple Macintosh use, a

separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector.

Wall-outlet type

Press the power button on the front panel to turn the power on. When monitor power is

turned on, the 'Self Image Setting Function' is executed automatically.

Power Button

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display

+ 26 hidden pages