Model
Language
Page
Material Size(W*H)
Date
Part No.
V-CP953** / V-CP963**
English/ French/ Deusch/ Nederlandse
16
Color(cover/body)
Weight 100g
2005.05.28
Designer
3828FI2852H Description
2/1
150×220(mm)
yang2
owner's manual
Chage Record
No. Date
1 Add the EU marking 05I0V04018 05.05.28 yang2 kimysk
Change the buyer name ACT701115 07.02.13 yang2 C.Y.T.
2
3
4
5
6
7
8
9
Change content
ECO No.
Designer
Confirm
V-CP953 S***/N***
V-CP963 S***/N***
V-CP973 S***/N***
V-CP983 S***/N***
E
F
D
N
-
E
- 4
Connecting the flexible hose
Assembling the tubes
(depending on model)
•
Metal(or Plastic) Pipe(4)
- Fit together the two tubes by twisting
slightly.
•
Telescopic tube(5)
-
-
-
• Crevice Tool(9)
• Dusting brush(10)
• Upholstery Nozzle(11)
How to plug in and use
Adjusting the power level
Storage(17)
Information for your safety
How to Use
Please read all the following information,
which contains important instructions for the
safety, the use and the maintenance of the
appliance.
This appliance complies with the following EC
Directives: -73/23/EEC, 93/68/EEC-Low
Voltage Directive-89/336EEC -EMC Directive.
Never allow children to use the appliance
unsupervised.
Do not use the appliance If the supply
cord is damaged or faulty.
If the mains lead is damaged, it must be
replaced by an approved LG Electronics
Service Agent in order to avoid a hazard.
Always switch the vaccum cleaner off
before :
¥ changing the dust bag.
¥ changing or cleaning the filters.
If no dustbag is inserted, the cover cannot
be closed. Please do not use force!
Do not vacuum flammable or explosive
substances(liquids or gases).
Do not vacuum hot ash, embers etc. nor
sharp objects.
Do not vacuum water or other liquids.
Push the end of the head(1) on the flexible
hose(2) into the attachment point on the
vacuum cleaner.
To remove the flexible hose from the
vacuum cleaner, press on the button(3)
situated on the head, then pull upwards.
Push spring latch(6) forward.
Pull out tube to required length.
Release spring latch to lock.
Using the cleaning head and Accessory
Nozzles(depending on model)
Fit the large cleaning head onto the end of
the tube.
The 2 position head(7) is equipped with a
pedal(8) which allows you to alter its
position according to the type of floor to be
cleaned.
Hard floor position(tiles,floors...). Press on
the pedal to lower the brush.
Carpet or rug position.Press on the pedal to
lift the brush up.
Hard floor Nozzle(26)
Efficient cleaning of hard floors
(wood, linoleum,etc.)
For vacuuming in those normally inaccessible places i.e. reaching cobwebs, or down
the side of a sofa!
For vacuuming picture frames furniture
outlines, books and other uneven objects.
For vacuuming uphostery, mattresses, etc.
The thread collectors help to pick up the
threads and fluff.
Pull out the supply cord to the desired
length and plug into the socket.
Press button (14) to start the vacuum cleaner.
To stop it press the button (14) again.
• If your appliance is equipped with an
electronic variable power control(13), you
can choose the power appropriated for the
task. The more you slide the button towards
the right, the greater the suction power.
• The flexible hose handle(15) has a manual
air flow regulator(16) which allows you to
briefly reduce the suction level.
When you have switched off and unplugged
the appliance, press on the button (12) to
automatically rewind the cord.
You can move or store your appliance in a
vertical position by sliding the hook on the
large cleaning head into the clip on the
underside of the appliance.
Changing the dust bag
The dustbag needs changing when the cleaner
is set to maximum power and the cleaner head
is off the floor but the Òbag fullÓ indicator
window
(18)
is completely coloured red.
Even if the dustbag does not appear to be
full at this stage, it should be changed.
It could be that a great deal of very fine dust
has clogged up the pores of the dust bag.
¥ Turn off the appliance and unplug it.
¥ Open the cover by pressing the hook
(19)
and lifting it up until it snaps into place.
Your appliance is equipped with either a
paper dust bag
(20)
or a fabric dust bag
(22)
(depending on model).
¥ Take hold of the dust bag by the handle
and pull.Remove the bag and throw it
away.
¥ To refit a new bag push the cardboard
support of a new bag into the bag mount
(21)
until it will go no furthe
r.
If your appliance is fitted with a fab-
ric dust bag
follow the same instructions
as above.
Empty it and replace it
(22)
.
Note
: as the appliance is fitted with a safety
device which checks that the bag is in place
you cannot close the lid if the bag is not
fitted correctly.
Cleaning the motor filter
The motor filter is situated inside the
appliance between the dust bag and the
motor. Each time that you change the air
outlet filter we advise you to remove the
motor filter
(23)
and to clean it by tapping to
remover the dirt and then replacing it in the
vacuum cleaner.
Check that the appliance is correctly plugged
Please never close the Filter Cover like
(25)
,
To avoid nipping your hand.
in and that the electrical socket is working.
¥
Stop the appliance and unplug it.
¥
Check that the tubes, flexible hose and
cleaning tool are not blocked.
¥
Check that the dust bag is not full.Replace
if necessary.
What to do if your appliance
WARNING
does not work?
What to do when the suction
performance reduces?
Cleaning the exhaust filter (24)
¥ Check the exhaust filter occasion-ally and
clean when dirty.
¥ Unplug cord from outlet.
¥ Open the exhaust cover and remove
exhaust filter as shown.
¥ Next procedures are the same as the
moter safety filter.