LG 90VR, 90VA, 90M, 90MK, U-42PZ44 User Manual

...

Page 1

PLASMA MONITOR

OWNER’S MANUAL

Please read this owner’s manual carefully before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and quote this information to your dealer when you require service.

Model number : Serial number :

MODELS : MU-42PZ44/44M/44V

MU-42PZ44A/44MA/44VA MU-42PZ44B/44MB/44VB MU-42PZ44K/44MK/44VK MU-42PZ44R/44MR/44VR MU-42PZ44S/44MS/44VS MU-42PZ90/90M/90V MU-42PZ90A/90MA/90VA MU-42PZ90B/90MB/90VB MU-42PZ90K/90MK/90VK MU-42PZ90R/90MR/90VR MU-42PZ90S/90MS/90VS MU-42PZ90C

P/NO : 3828VA0361H (RF03GA)

LG Electronics U.S.A., Inc.

Page 2

2 Plasma Display

Warning

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

FCC NOTICE

• A Class B digital device

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-201-816-2000 http://www.lgusa.com

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

arning

Page 3

Owner’s Manual 3

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

Safety Instructions

Page 4

4 Plasma Display

Safety Instructions

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been

damaged. f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Safety Instructions continued

Page 5

Owner’s Manual 5

Contents

After reading this manual, keep it handy for future reference.

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls and Connection Options . . . . . . . . . . . .7

Remote Control Key Functions . . . . . . . . . . . . . .8

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10

External Equipment Connections . . . . . . . . . .11~14

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11

External A/V Source Setup . . . . . . . . . . . . . . . .12

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14

Operation

Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15

Menu Language Selection . . . . . . . . . . . . . . . . . .15

Picture Menu Options

APC (Auto Picture Control) . . . . . . . . . . . . . . . .16

Manual Picture Control . . . . . . . . . . . . . . . . . . .16

Auto Color Temperature Control . . . . . . . . . . . .16

Manual Color Temperature Control . . . . . . . . . .16

Sound Menu Options

DASP (Digital Auto Sound Processing) . . . . . . .17

Manual Sound Control . . . . . . . . . . . . . . . . . . .17

AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17

Timer Menu Options

Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18

On/Off Timers Setup . . . . . . . . . . . . . . . . . . . . .18

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Special Menu Options

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

ISM (Image Sticking Minimization) Method . . . .19

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Menu Rotation For Vertical Viewing . . . . . . . . . .20

Screen Menu Options

Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .21

Setting Picture Format . . . . . . . . . . . . . . . . . . .21

Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .21

Adjusting Horizontal/Vertical Position . . . . . . . .22

Manual Configure . . . . . . . . . . . . . . . . . . . . . . .22

Screen Adjustments . . . . . . . . . . . . . . . . . . . . .22

Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Luminance Noise Reduction . . . . . . . . . . . . . . .23

Selecting Wide VGA mode . . . . . . . . . . . . . . . .23

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

PIP (Picture In Picture) Feature

Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .24

Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .24

Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Selecting a Input Signal Source for PIP . . . . . . .24

PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .24

Double Window Setup Options

Watching Double Window . . . . . . . . . . . . . . . . .25

Sub Picture Size Adjustment . . . . . . . . . . . . . . .25

Swapping the Double Window . . . . . . . . . . . . .25

Selecting a Source for the Double Window . . . .25

External Control Device Setup . . . . . . . . . . . . . . . .26~31

IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32~33

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .34

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Contents

Page 6

6 Plasma Display

Introduction

What is a Plasma Display Panel (PDP)?

If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room.

Wide Screen

The screen of the Plasma Display is 42" so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit.

The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

WARNING

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Page 7

Owner’s Manual 7

Introduction

Controls

Connection Options

( )

VIDEO INPUT

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

YPBP

(MONO)

AUDIO

S-VIDEO

AC INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

DVI INPUT

RGB INPUT

RGB OUTPUT

1. EXTERNAL SPEAKER (8 ohm output)

Connect to optional external speaker(s). * For further information, refer to ‘Speaker & Speaker

Stand’ manual.

2. RS-232C INPUT (CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

3. DVI (Digital Visual Interface) INPUT/ RGB INPUT/AUDIO INPUT JACKS

Connect the monitor output connector of a PC to the appropriate input port.

4. RGB OUTPUT JACKS

You can watch the RGB signal on another monitor, connect RGB OUTPUT to another monitor’s PC input port.

5. EXPANDED INPUT

6. COMPONENT INPUT/AUDIO INPUT JACKS

Connect a component video/audio device to these jacks.

7. REMOTE CONTROL

Connect your wired remote control to the remote control port on the Monitor.

8. S-VIDEO INPUT

Connect S-Video out from an S-VIDEO VCR to the S-VIDEO input.

AUDIO/VIDEO INPUT JACKS

Connect audio/video out from external equipment to these jacks.

9. POWER CORD SOCKET

This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power.

Back Connection Panel

Front Panel Controls

2 4 5 73 8

Main Power Button

INPUT SELECT Button

VOLUME (F,G) Buttons

Power Standby Indicator

Illuminates red in standby mode,

Illuminates green when the

Monitor is turned on

Remote Control Sensor

MENU Button

E, D Buttons

- This is a simplified representation of front panel.

Here shown may be somewhat different from your monitor.

- Connection panels shown may be somewhat different from your monitor.

ON/OFF

Page 8

8 Plasma Display

Introduction

Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the monitor.

- Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary.

• Open the battery compartment cover on the back side and insert the batteries with correct polarity.

• Install two 1.5V batteries of AAA type. Don’t mix used batteries with new batteries.

Installing Batteries

123

456

7809

POWER

MULTIMEDIA INPUT SELECT

APC DASP

ARC SLEEP

PIP

SWAP

MENU MUTE

ENTER

VOL

POWER

STOP

REC

PLAY

REW

P/STILL

WIN.SIZE

WIN.POSITION

FAV CH

CAPTION

A.PROG PIP CH

PIP CH

ZOOM +

MTS

ZOOM -

SPLIT ZOOM

MEMORY/ERASE

VOL

PIP INPUT

POWER

Switches the monitor between

ON and STANDBY.

MULTIMEDIA

Selects:

Component, RGB, or DVI

mode.

APC

Adjusts the factory preset picture

according to the room.

ARC

Changes the picture format.

PIP

Switches the sub picture on and off.

SWAP

Exchanges main and sub picture

images.

Displays on screen menus.

Exits the current menu.

ENTER

DD / EE

(Channel button)

Selects menu options.

VOL FF / GG (Volume button)

Increases/decreases sound level. Adjusts menu settings.

INPUT SELECT

Selects source:

Video, S-Video,

Component, RGB, or DVI mode.

DASP

Selects the sound appropriate to your viewing program character:

Flat, Music, Movie, Sports, or User.

SLEEP

Sets the sleep timer.

PIP INPUT

Selects the input mode for the sub picture.

MUTE

Switches the sound on or off.

ZOOM-/ZOOM+

Enlarges or reduces the main picture size.

DW (Double Window)

Selects Double Window mode.

WIN. SIZE

Adjusts the sub picture size.

WIN.POSITION

Moves the sub picture.

NUMBER buttons

Not functional

VCR BUTTONS

Control some LG video cassette recorders.

SPLIT ZOOM

Enlarge the screen with regular

ration.

Page 9

Owner’s Manual 9

Installation

D-sub 15 pin Cable

Owner’s Manual

1.5V

Batteries

BNC-RCA Adapter

Power Cord

123

456

7809

POWER

SLEEP INPUT SELECT

APC DASP

ARC PIP ARC

PIP

TWIN PICTURE

SWAP

MENU MUTE

VOL

POWER STOP

PLAY FF

REC

REW

P/STILL

WIN.SIZE

WIN.POSITION

ZOOM +

ZOOM -

SPLIT ZOOM

VOL

SUB INPUT

Remote Control

DVI-D Cable

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

Installation Instructions

• The Monitor can be installed in various ways such as on a wall, or on a desktop etc.

• The plasma display is designed to be mounted horizontally or vertically. The speakers depicted are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

WWall Mount: Horizontal installation

all Mount: Horizontal installation

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are included from your dealer in the optional Wall Mounting Bracket Installation and Setup Guide.

4 inches

4 inches4 inches

4 inches

2 inches

Page 10

10 Plasma Display

Installation

WWall Mount: V

all Mount: V

ertical installation (MU-42PZ44M/44V/90C/90M/90V series models only)

Detailed installation instructions are included in the optional Vertical Wall Mounting Bracket Installation and Setup Guide, see your dealer. NOTE: When installing the monitor vertically, the front panel controls must be in the left side position.

When installing the monitor vertically, you have to change the OSD (On Screen Display) display mode so that the menus will appear correctly and also to protect the monitor from overheating (Refer to P. 20).

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide, see your dealer.

Installation Instructions continued

4 inches

2 inches

4 inches

2.36 inches

Page 11

Owner’s Manual 11

Installation

External Equipment Connections

NOTE: All cables shown are not included with the plasma display.

- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor

- Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen.

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s

VIDEO INPUT.

2. Connect the audio and video cables from the VCR's output

jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a VCR, match the jack colors: (Video = yellow, Audio Left = white, and Audio Right = red).

VCR: Connect the video output cable from the VCR to the VIDEO input on the monitor.

S-VIDEO VCR: Connect the S-Video output cable from the VCR to the S-VIDEO input. (Note that S-Video yields higher quality video).

How to use

1. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

2. Use the INPUT SELECT button on the remote control to select

Video. (If connected to S-VIDEO, select the S-Video external input source.)

VCR Setup

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s

VIDEO INPUT.

2. Connect the audio and video cables from the cable box's out-

put jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a cable TV, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Use the INPUT SELECT button on the remote control to select Video.

2. Select your desired channel with the cable box remote control.

Cable

TV Setup

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

VIDEO INPUT

YPB PR

(MONO)

AUDIO

S-VIDEO AUDIO INPUT

AUDIO INPUT

REMOTE

CONTROL

COMPONENT INPUT

VCR

RF Cable

(R) AUDIO (L) VIDEO

VIDEO INPUT

YPB PR

(MONO)

AUDIO

S-VIDEO AUDIO INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

Cable Box

Page 12

12 Plasma Display

Installation

• Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

- To watch digitally broadcast programs, purchase and connect a digital set-top box.

- This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) modes.

How to connect

1. Use the monitor’s COMPONENT (Y, P

, P

) INPUT, RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

2. Use INPUT SELECT on the remote control to select Component, RGB or DVI.

DTV Setup

How to connect

1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT.

2. Connect the audio and video cables from the external equipment's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Use the INPUT SELECT button on the remote control to select Video.

2. Operate the corresponding external equipment. Refer to external equipment operating guide.

Component ports of the

Monitor

Y PB

Video output ports of DVD player

Y Y Y Y

B-Y

R-Y

Cr P

How to connect

1. Connect the DVD video outputs to the COMPONENT (Y, P

B, P

INPUT jacks and connect the DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the monitor and connect the DVD audio outputs to the AUDIO INPUT jacks, as shown in the figure.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the INPUT SELECT button on the remote control to select Component. (If connected to S-VIDEO, select the S-Video external input source.)

3. Refer to the DVD player's manual for operating instructions.

External

A/V Source Setup

DVD Setup

AUDIO VIDEO

Video game set

Camcorder

VIDEO INPUT

YPBP

(MONO)

AUDIO

S-VIDEO AUDIO INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

(R) AUDIO (L) (R) AUDIO (L)

S-VIDEO

VIDEO INPUT

YPBP

(MONO)

AUDIO

S-VIDEO AUDIO INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

DVD

VIDEO INPUT

YPBP

(MONO)

AUDIO

S-VIDEO AUDIO INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

(R) AUDIO (L)

AUDIO INPUT

DVI INPUT

RGB INPUT

RGB OUTPUT

RGB-DTV OUTPUT

(R) AUDIO (L)

DVI-DTV OUTPUT

Digital Set-top Box

or or

Page 13

Owner’s Manual 13

Installation

How to connect

1. To get the best picture quality, adjust the PC graphics card to 800x600, 60Hz.

2. Use the monitor’s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector.

If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI INPUT to display

the PC image on the monitor. If the graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or DVI; (the other mode is set to Plug and Play automatically by the monitor.)

3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the monitor.

2. Turn on the display by pressing the POWER button on the monitor's remote control.

3. Use the INPUT SELECT button on the remote control to select RGB or DVI.

4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES

• Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.

• Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become perma-

nently imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

PC Setup

- This Plasma display provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol.

( )

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

AUDIO INPUT

DVI INPUT

RGB INPUT

RGB OUTPUT

Page 14

14 Plasma Display

Installation

Resolution

640x350

720x400

640x480

848x480

852x480

Horizontal

Frequency(KHz)

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.500

35.00

37.500

31.500

35.000

37.500

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

54.348

63.995

67.500

68.681

60.000

63.981

56.25

60.31

72.18

75.00

85.06

74.55

60.00

70.06

75.02

60.05

70.01

75.00

75.06

60.00

60.02

Vertical

Frequency(Hz)

Resolution

800x600

832x624

1024x768

1152x864

1152x870

1280x1024

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

1280x960

Monitor Display Specifications (RGB-PC /DVI-PC Mode)

Page 15

Owner’s Manual 15

Operation

Turning on the Monitor just after installation

Turning on the Monitor (power cord is still connected)

1. Connect power cord correctly.

2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby

mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT, MULTIMEDIA button on the remote control to switch the Monitor on.

• Press the ON/OFF button on the Monitor to turn the Monitor on.

1. If the Monitor was turned off with the ON/OFF button on the Monitor

2. If the Monitor was turned off with the remote control and the ON/OFF button on the Monitor

• Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor. Or, on the remote control, press POWER, INPUT SELECT, or MULTIMEDIA to turn the Monitor on.

- The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use

D/ E

button to select the SPECIAL menu.

2. Press the G button and then use

D/ E

button to select Language.

3. Press the G button and then use

D/ E

button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice.

4. Press the ENTER button to save.

SPECIAL

Prev.

Language GG

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

OSD Rotate

English

Español

Français

SPECIAL

Operation

Menu Language Selection

TTurning on the Monitor

urning on the Monitor

Page 16

16 Plasma Display

Operation

- Each adjustment for the Picture menu options doesn’t effect other input sources. Readjust Picture menu options for each of the following sources.

• RGB (PC) / DVI (PC),

• RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i)

• Video / S-Video / Component (480i)

Picture Menu Options

- You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer.

1. Press the MENU button and then use

D / E

button to select the PICTURE menu.

2. Press the G button and then use

D / E

button to select the desired picture option

(

Contrast, Brightness, Color, Sharpness, Tint).

3. Press the G button and then use F / G button to make appropriate adjustments.

4. Press the ENTER button to save.

Manual Picture Control (

Manual Picture Control (User

option)

1. Press the APC button repeatedly to select the picture appearance setup option as shown below.

APC (Auto Picture Control)

• You can also adjust APC in the PICTURE menu.

• Clear, Optimum, and Soft are preset for good picture quality at the factory and cannot be changed.

Optimum Soft User Clear

- APC adjusts the Monitor for the best picture appearance.

- When adjusting picture options (contrast, brightness, color, sharpness and tint) manually, APC automatically changes to User.

- To initialize values (reset to default settings), select the

Normal option.

- When adjusting color temperature options (red, green, or blue) manually, ACC automatically changes to

User.

1. Press the MENU button and then use

D / E

button to select the PICTURE menu.

2. Press the G button and then use

D / E

button to select ACC .

3. Press the G button and then use

D / E

button to select either Normal (Default),

Cool (Preset), Warm (Preset) or User (Manual Adjustment).

4. Press the ENTER button to save.

Auto Color

Auto Color TT

emperature Control

- You can adjust red, green, or blue to any color temperature you prefer.

1. Press the MENU button and then use

D / E

button to select the PICTURE menu.

2. Press the

G button and then use

D / E

button to select Color temp .

3. Press the G button and then use

D / E

button to select Red, Green or Blue.

4. Use the F / G button to make appropriate adjustments.

• The adjustment range of Red, Green,

and

Blue is -20 ~ +20.

5. Press the ENTER button to save.

Manual Color

Manual Color TT

emperature Control (

emperature Control (User

option)

PICTURE

Prev.

APC

ACC GG

Color temp.

Contrast 80

Brightness 60

Color 50

Sharpness 50

Tint 0

PICTURE

Normal

Cool

Warm

User

PICTURE

Prev.

APC

ACC

Color temp. GG

Contrast 80

Brightness 60

Color 50

Sharpness 50

Tint 0

PICTURE

Red 0

Green 0

Blue 0

PICTURE

Prev.

APC

ACC

Color temp.

Contrast 80 GG

Brightness 60

Color 50

Sharpness 50

Tint 0

PICTURE

Page 17

Owner’s Manual 17

Operation

1. Press the DASP button repeatedly to select the appropriate sound setup as shown below.

DASP

(Digital

Auto Sound Processing)

Press the MENU button and then use

D / E

button to select the SOUND menu.

2. Press the G button and then use

D / E

button to select the desired sound option

(

Balance, Treble, Bass).

3. Press the G button and then use F / G button to make appropriate adjustments.

4. Press the ENTER button to save.

Manual Sound Control (

Manual Sound Control (User

option)

• You can also adjust DASP in the SOUND menu.

• Flat, Music, Movie and Sports are preset for good sound quality at the factory and cannot be

changed.

Flat Music Movie Sports User

- This function lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound option based on the program content.

- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User.

- AVL maintains an equal sound level; even if you change channels.

1. Press the MENU button and then use

D / E

button to select the SOUND menu.

2. Press the G button and then use

D / E

button to select AVL.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press the ENTER button to save.

AAVLVL(Auto V

(Auto V

olume Leveler)

- You can adjust sound treble, bass, and balance to the levels you prefer.

SOUND

Prev.

DASP

AVL

Balance 0

Treble 50

Bass 50

SOUND

Off

SOUND

Prev.

DASP

AVL

Balance 0

Treble 50 GG

Bass 50

SOUND

Sound Menu Options

Page 18

18 Plasma Display

Operation

- Timer functions operate only if current time has been set.

- Off-Timer function overrides On-Timer function if they are set to the same time.

- The monitor must be in standby mode for the On-Timer to work.

On/Of

On/Off f TT

imers Setup

1. Press the MENU button and then use

D / E

button to select the TIMER menu.

2. Press the

G button and then use

D / E

button to select Off timer or On timer.

3. Press the G button and then use

D / E

button to select On.

• To cancel On/Off timer function, select Off.

4. Press the G button and then use

D / E

button to set the hour.

5. Press the G button and then use

D / E

button to set the minutes.

6. For only

On timer function; Press the G button and then use

D / E

button to set

sound level.

7. Press the ENTER button to save.

Clock Setup

1. Press the MENU button and then use

D / E

button to select the TIMER menu.

2. Press the

G button and then use

D / E

button to select Clock.

3. Press the G button and then use

D / E

button to set the hour.

4. Press the G button and then use

D / E

button to set the minutes.

5. Press the ENTER button to save.

TTimer Menu Options

imer Menu Options

TIMER

Prev.

Clock GG

Off timer

On timer

Auto off

TIMER

- - : - -

Sleep

Sleep TT

imer

- The Sleep Timer turns the Monitor off at the preset time. Note that this setting is cleared when the monitor is turned off.

1. Press the SLEEP button repeatedly to select the number of minutes. First the ---

Min option appears on the

screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to

count down from the number of minutes selected.

3. To check the remaining minutes before the monitor turns off, press the SLEEP or ENTER button once.

4. To cancel the Sleep Timer, press the SLEEP button repeatedly until ---

Min appears.

Auto Of

Auto Offf

- If there is no input signal, the Monitor will turn off automatically after 10 minutes.

1. Press the MENU button and then use

D / E

button to select the TIMER menu.

2. Press the G button and then use

D / E

button to select Auto off.

3. Press the G button and then use

D / E

button to select On or Off.

4. Press the ENTER button to save.

TIMER

Prev.

Clock

Off timer

On timer

Auto off

TIMER

Off

TIMER

Prev.

Clock

Off timer

On timer GG

Auto off

TIMER

10 : 30

Vol. 30

Ch. TV 2

Off

- If current time setting is erased by a power failure, if TV is unplugged or if the monitor is turned off with the ON/OFF button on the monitor, reset the clock.

Page 19

Owner’s Manual 19

Key Lock

- The monitor can be set up so that it can only be used with the remote control.

- This feature can be used to prevent unauthorized viewing by disabling the front panel controls.

- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time.

Special Menu Options

SPECIAL

Prev.

Language

Key lock GG

ISM Method

Low power

Set ID

Caption / Text

Captions

OSD Rotate

Off

SPECIAL

1. Press the MENU button and then use

D / E

button to select the SPECIAL menu.

2. Press the

button and then use

D / E

button to select Key lock.

3. Press the G button and then use

D / E

button to select On or Off.

4. Press the ENTER button to save.

• With the KEY LOCK ON, the display ‘ Key lock’ appears on the screen if any button on the front panel is pressed.

ISM (Image Sticking Minimization) Method

SPECIAL

Prev.

Language

Key lock

ISM Method GG

Low power

Set ID

Caption / Text

Captions

OSD Rotate

Normal

White wash

Orbiter

Inversion

SPECIAL

1. Press the MENU button and then use

D / E

button to select the SPECIAL menu.

2. Press the

G button and then use

D / E

button to select ISM Method.

3. Press the G button and then use

D / E

button to select either Normal, White

wash

, Orbiter, or Inversion.

• Normal:

If image sticking is never a problem, ISM is not necessary - set to Normal.

• White wash

White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button.

• Orbiter

Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 1 minutes: Right → Right → Downside → Downside →

Left → Left → Upside → Upside.

• Inversion

Inversion will automatically invert the plasma display panel color every 30 minutes.

4. Press the ENTER button to save.

Low Power

- Low power reduces the plasma display power consumption.

SPECIAL

Prev.

Language

Key lock

ISM Method

Low power GG

Set ID

Caption / Text

Captions

OSD Rotate

Off

SPECIAL

1. Press the MENU button and then use

D / E

button to select the SPECIAL menu.

2. Press the Gbutton and then use

D / E

button to select Low power.

3. Press the Gbutton and then use

D / E

button to select On or Off.

• When you select On, the screen darkens.

4. Press the ENTER button to save.

Page 20

20 Plasma Display

Special Menu Options continued

SPECIAL

Prev.

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

OSD Rotate

Normal

Rotate

SPECIAL

1. Press the MENU button and then use

D / E

button to select the SPECIAL menu.

2. Press the

G button and then use

D / E

button to select OSD (On Screen Display)

Rotate.

3. Press the G button and then use

D / E

button to select Normal or Rotate.

• Select Normal, if the monitor was installed horizontally.

• Select Rotate, if the monitor was installed vertically.

4. Press the ENTER button to save.

Menu Rotation for V

ertical V

iewing (MU-42PZ44M/44V/90C/90M/90V series models only)

Operation

Page 21

Owner’s Manual 21

Operation

Auto

Adjustment

- RGB (PC) mode only; This function doesn’t work for RGB-DTV mode.

- Automatically adjusts picture position and minimizes image shaking.

- After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment.

- The Auto config. and Manual config. are not active in DVI mode.

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the

G button and then use

D / E

button to select Auto config..

3. Press the G button to run Auto configure.

• When Auto config. has finished, OK will be shown on screen.

• If the position of the image is still not correct, try Auto adjustment again.

4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto con-

fig.

, you can make further adjustments with the Manual config. option.

Screen Menu Options

SCREEN

Prev.

Auto config. GG

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

VGA Mode

To set

SCREEN

Setting Picture Format

- Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible.

- Set every aspect ratio for RGB 480p, DVI 480p, Component 480i/480p, Video, and S-Video sources.

- Use 4:3, or 16:9 for other input sources.

1. Use the ARC button repeatedly to select the desired picture format. You can also adjust

ARC in the SCREEN menu.

• 4:3

- Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.

• 16:9

- Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

• Horizon

- Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.

• Zoom

- Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.

1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size.

• Zoom adjustment range is 100~300.

2. Adjust the main picture position using the

D / E

/ F / G buttons while in the

enlarged picture mode.

Picture Size Zoom

- When enlarging or reducing the picture, the image may become distorted.

Zoom out

100%

Page 22

22 Plasma Display

Adjusting Horizontal/ V

ertical Position

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the G button and then use

D / E

button to select Position.

3. Press the G button and then use

D / E /

F / G button to adjust the position.

4. Press the ENTER button to save.

SCREEN

Prev.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

VGA Mode

SCREEN

Prev.

Auto config.

ARC

Zoom in/out

Position

Manual config. GG

Screen adj.

Reset

VGA Mode

SCREEN

Manual Configure (RGB-PC mode only)

- If the image still isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture Phase manually.

- To correct the screen size, adjust Clock.

- This function works in the following modes:

RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i).

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the G button and then use

D / E

button to select Manual config..

3. Press the G button and then use

D / E

button to to select Phase or Clock.

4. Use the F / G button to make appropriate adjustments.

• The Phase adjustment range is 0 ~ 31.

• The Clock adjustment range is -50 ~ +50.

5. Press the ENTER button to save.

Phase 0

Clock 0

SCREEN

Prev.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj. GG

Reset

YNR

SCREEN

Screen

Adjustments (V

ideo, S-V

ideo and Component 480i mode only)

- Use this function to correct jittering or picture instability while viewing a video tape.

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the G button and then use

D / E

button to select Screen adj..

3. Press the G button and then use

D / E

button to select TV or VCR.

• Select the VCR option if watching a VCR.

• Select the TV option for other equipment. (Except VCR)

4. Press the ENTER button to save.

VCR

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the Gbutton and then use

D / E

button to select Reset.

3. Press the

G button.

• You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP position and sub picture size for double window.

Initializing (Reset to original factory value)

- This function operates in every mode.

- Use the Reset option to initialize the adjusted settings.

SCREEN

Prev.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

YNR

To set

SCREEN

Operation

Screen Menu Options continued

Page 23

Owner’s Manual 23

Operation

Split Zoom

- Enlarges the picture in correct proportions.

- Split Zoom can be used for all input sources.

- In 2-Split Zoom mode, you can only move the image up or down.

- If an image is enlarged, a section can be viewed without using Split Zoom.

- Split Zoom is not available if OSD rotate is rotate.

1. Press the SPLIT ZOOM button repeatedly to select either 2, 4, or 9 Split Zoom.

2. Press the number button corresponding to the section you wish to enlarge. you can move the enlarged screen with using the

D / E

/ F / G button.

SCREEN

Prev.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

VGA Mode GG

640x480

848x480

852x480

SCREEN

Prev.

Auto config.

ARC

Zoom in/out

Position

Manual config.

Screen adj.

Reset

YNR GG

Off

SCREEN

Selecting W

ide VGA

mode (RGB-PC, DVI-PC mode only)

- To see a normal picture, match the resolution of RGB mode and selection of VGA mode.

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the G button and then use

D / E

button to select VGA Mode.

3. Press the G button and then use

D / E

button to select the desired VGA resolution.

4. Press the ENTER button to save.

▲ ▼

◀▶

2-Split zoom

▲ ▼

◀▶

4-Split zoom

▲ ▼

◀▶

9-Split zoom

Example of choosing 5.

Section 5 is enlarged to fill the screen.

▲ ▼

◀▶

9-Split zoom

- Use YNR to reduce the picture noise that may appear on the screen.

Luminance Noise Reduction (V

ideo, S-V

ideo and Component 480i modes only)

1. Press the MENU button and then use

D / E

button to select the SCREEN menu.

2. Press the G button and then use

D / E

button to select YNR.

3. Press the G button and then use

D / E

button to select On or Off.

4. Press the ENTER button to save.

Page 24

24 Plasma Display

- PIP lets you view 2 different inputs pictures (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image.

- You can also adjust the PIP features in the PIP/DW menu (Except Swap function).

PIP

(Picture-In-Picture) Feature

PIP/DW

Prev.

Input

PIP

PIP Input

Win. size

Win. position

PIP ARC GG

4 : 3

16 : 9

PIP/DW

Operation

WWatching PIP

atching PIP

Press the PIP button repeatedly to turn PIP on or off.

- Press the WIN.SIZE button and then use

F / G button to change the sub

picture size.

- To watch 4: 3 or 16:9 aspect ratio for sub picture

PIP

Aspect Ratio

Moving the PIP

Press the WIN.POSITION button. Press the

D / E

/ F / G button repeatedly until desired position is achieved.

The sub picture moves up/down/left/right. You can also move the PIP position with

Win.position in the PIP/DW menu.

Swapping the PIP

Press the SWAP button to exchange the main and sub pictures.

Selecting an Input Signal Source for the PIP

Use the PIP INPUT button to select the input source for the sub picture.

Main Picture Sub Picture

Win.position

Component

Video

Component

Video

Component

1. Press the MENU button and then use

D / E

button to select the PIP/DW menu.

2. Press the Gbutton and then use

D / E

button to select PIP ARC.

3. Press the G button and then use

D / E

button to select 4:3 or 16:9.

4. Press the ENTER button to save.

Win.size

FF GG

Main Picture Source

Available Sub Picture Sources

Video S-Video Component 480i Component 480p/720p/1080i RGB and DVI

S-Video, Component 480i/480p/720p/1080i, RGB and DVI Video, Component 480i/480p/720p/1080i, RGB, and DVI Video,S-Video, RGB, and DVI Video and S-Video Video, S-Video, and Component 480i,

10 : 30

10 : 30 10 : 30

▲

◀▶

▼

Page 25

Owner’s Manual 25

Operation

- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen.

Double W

indow Setup Options

Selecting a Source for the Double W

indow

WWatching Double W

atching Double W

indow

Press the DW button repeatedly to select one of the Double Window options.

Sub Picture Size

Adjustment

Press the WIN.SIZE button.

• Use the F / G button to change the sub picture size.

• Using the Win.size function in Double Window mode, main and sub picture sizes are

changed simultaneously. Using the Win.size function in PIP mode, sub picture size is changed.

• Win.position is not functional in Double Window mode.

Swapping the Double W

indow

Use the SWAP button to switch the main and sub pictures in Double Window mode.

DW 1

DW 2

10 : 30

◀▶

Component

Video

Component

Win.size

FF GG

Main Picture Sub Picture

Use the PIP INPUT button to select the input source for the sub picture. You can also select PIP Input in the PIP/DW menu.

Main Picture Source

Available Sub Picture Sources

Video S-Video Component 480i Component 480p/720p/1080i RGB and DVI

S-Video, Component 480i/480p/720p/1080i, RGB and DVI Video, Component 480i/480p/720p/1080i, RGB, and DVI Video,S-Video, RGB, and DVI Video and S-Video Video, S-Video, and Component 480i,

Page 26

26 Plasma Display

No. Pin name 1 No connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection

2 3 5 4 6 7 8

RXD TXD

GND

DTR DSR

RTS

CTS

TXD RXD GND DSR DTR

CTS

RTS

7-Wire Configurations

(Standard RS-232C cable)

D-Sub 9

3 2 5 6 4 8 7

PDP

D-Sub 9

2 3 5 4 6 7 8

RXD TXD GND DTR DSR RTS CTS

TXD

RXD

GND

DTR DSR

RTS CTS

3-Wire Configurations

(Not standard)

D-Sub 9

3 2 5 4 6 7 8

PDP

D-Sub 9

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.

- RS-232C connection cables are not supplied with the Monitor.

TType of Connector; D-Sub 9-Pin Male

ype of Connector; D-Sub 9-Pin Male

RS-232C Configurations

External Control Device Setup

RS-232C Setup

( )

VIDEO INPUT

RS-232C INPUT

(CONTROL/SERVICE)

EXTERNAL SPEAKER

YPBP

(MONO)

AUDIO

S-VIDEO

AC INPUT

AUDIO INPUT

REMOTE CONTROL

COMPONENT INPUT

DVI INPUT

RGB INPUT

RGB OUTPUT

External Control Device Setup

Page 27

Owner’s Manual 27

External Control Device Setup

Set ID

Use this function to specify a monitor ID number. Refer to ‘Real Data Mapping 1’. See page 28.

• Baud rate : 115200 bps (UART)

• Data length : 8 bits

• Parity : None

* Use a crossed (reverse) cable.

• Stop bit : 1 bit

• Communication code : ASCII code

Communication Parameters

1. Press the MENU button and then use

D / E

button to select the SPECIAL menu.

2. Press the G button and then use

D / E

button to select Set ID.

3. Press the G button and then use F / G button to adjust Set ID to choose the desired

monitor ID number. The adjustment range of Set ID is 1 ~ 99.

4. Press the ENTER button to save.

SPECIAL

Prev.

Language

Key lock

ISM Method

Low power

Set ID

Caption / Text

Captions

OSD Rotate

SPECIAL

Transmission

[Command 1]: First command to control PDP set. (j or k)

[Command 2]: Second command to control PDP set.

[Set ID]: You can adjust the set ID to choose desired monitor

ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.

[DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

[Cr]: Carriage Return

ASCII code ‘0x0D’

[ ]: ASCII code ‘space (0x20)’

[Command1][Command2][ ][Set ID][ ][Data][Cr]

TTransmission / Receiving Protocol

ransmission / Receiving Protocol

Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

[Command2][ ][Set ID][ ][OK][Data][x]

Error

Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving abnormal data from non-viable functions or communication errors.

[Command2][ ][Set ID][ ][NG][Data][x]

Data 1: Illegal Code

2: Not supported function 3: Wait more time

01. Power k a 0 ~ 1

02. Input Select k b 0 ~ 4

03. Aspect Ratio k c 0 ~ 3

04. Screen Mute k d 0 ~ 1

05. Volume Mute k e 0 ~ 1

06. Volume Control k f 0 ~ 64

07. Contrast k g 0 ~ 64

08. Brightness k h 0 ~ 64

09. Color k i 0 ~ 64

10. Tint k j 0 ~ 64

11. Sharpness k k 0 ~ 64

12. OSD Select k l 0 ~ 1

13.

Remote Control Lock Mode

k m 0 ~ 1

14. PIP/Twin k n 0 ~ 3

15. PIP Aspect Ratio k o 0 ~ 1

16. Split Zoom k p 21 ~99

17. PIP Position k q 0 ~ 3

18. Treble k r 0 ~ 64

19. Bass k s 0 ~ 64

20. Balance k t 0 ~ 64

21. Color Temperature k u 0 ~ 3

22. Red Adjustment k v 0 ~ C8

23. Green Adjustment k w 0 ~ C8

24. Blue Adjustment k $ 0 ~ C8

25. PIP Input Source k y 0 ~ 4

26. Abnormal State k z 0 ~ a

27. ISM Method j p 0 ~ 3

28. Low Power j q 0 ~ 1

29. Orbiter Time Setting j r 1 ~ FE

30. Orbiter Pixel Setting j s 0 ~9

31. Picture Size Setting j t 0 ~64

for Double Window mode

32. Auto Config j u 1

COMMAND 1 COMMAND 2 DATA

(Hexadecimal)

•

Menu doesn’t display on screen when setting the 4,

12, 13, and 26 ~ 32.

Command Reference List

Page 28

28 Plasma Display

External Control Device Setup

02. Input Select (Command2:b) (Main Picture Input)

G To select input source for the Monitor.

You can also select an input source using the INPUT SELECT button on the Monitor's remote control.

ransmission

Data 0 : RGB

1 : Component 2 : Video

3 : S-Video 4 : DVI

[k][b][ ][Set ID][ ][Data][Cr]

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

01. Power (Command2:a)

G To control Power On/Off of the Monitor.

Transmission

Data 0 : Power Off 1 : Power On

[k][a][ ][Set ID][ ][Data][Cr]

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

G To show Power On/Off.

Transmission

[k][a][ ][Set ID][ ][FF][Cr]

Acknowledgement

Data 0 : Power Off 1 : Power On

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback presents status about each function.

[a][ ][Set ID][ ][OK][Data][x]

Real data mapping 1

0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

64 : Step 100

05. Volume Mute (Command2:e)

G To control volume mute on/off.

You can also adjust mute using the MUTE button on remote control.

ransmission

Data 0 : Volume mute on (Volume off)

1 : Volume mute off (Volume on)

[k][e][ ][Set ID][ ][Data][Cr]

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format)

G To adjust the screen format.

You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu.

ransmission

Data 0 : Wide screen (16:9)

1 : Normal screen (4:3) 2 : Full screen (Zoom) 3 : Horizon

[k][c][ ][Set ID][ ][Data][Cr]

Acknowledgement

* You select either 16:9 or 4:3 screen aspect ratio using the

PC, DTV 720p/1080i.

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command2:d)

G To select screen mute on/off.

ransmission

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

[k][d][ ][Set ID][ ][Data][Cr]

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

06. Volume Control (Command2:f)

G To adjust volume.

You can also adjust volume with the volume buttons on remote control.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping 1’ as shown below.

[k][f][ ][Set ID][ ][Data][Cr]

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

G To adjust screen contrast.

You can also adjust contrast in the Picture menu.

ransmission

Data Min : 0 ~ Max : 64

•

Refer to ‘Real data mapping 1’ as shown below.

[k][g][ ][Set ID][ ][Data][Cr]

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

Page 29

Owner’s Manual 29

External Control Device Setup

09. Color (Command2:i)

G To adjust the screen color.

You can also adjust color in the Picture menu.

ransmission

Data Min : 0 ~ Max : 64

•

Refer to ‘Real data mapping 1’. See page 28.

[k][i][ ][Set ID][ ][Data][Cr]

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

G To adjust the screen tint.

You can also adjust tint in the Picture menu.

ransmission

Data Red : 0 ~ Green : 64

•

Refer to ‘Real data mapping 1’. See page 28.

[k][j][ ][Set ID][ ][Data][Cr]

Acknowledgement

[j][ ][Set ID][ ][OK][Data][x]

08. Brightness (Command2:h)

G To adjust screen brightness.

You can also adjust brightness in the Picture menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping 1’. See page 28.

[k][h][ ][Set ID][ ][Data][Cr]

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m)

G To lock the remote control and the front panel controls on

the monitor.

ransmission

[k][m][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Lock off 1: Lock on

• If you’re not using the remote control and front panel con-

trols on the monitor, use this mode. When main power is on/off, remote control lock is released.

[m][ ][Set ID][ ][OK][Data][x]

14. PIP / DW (Command2:n)

G To control the PIP (Picture In picture)/DW (Double Window).

You can also control the PIP/DW using the PIP or DW button on the remote control or in the PIP/DW menu.

Transmission

Data 0: PIP/DW off

1: PIP

2: DW1 3: DW2

[k][n][ ][Set ID][ ][Data][Cr]

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

G To adjust the screen sharpness.

You can also adjust sharpness in the Picture menu.

ransmission

11. Sharpness (Command2:k)

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 28.

[k][k][ ][Set ID][ ][Data][Cr]

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

G To select OSD (On Screen Display) on/off.

ransmission

[k][l][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: OSD off 1: OSD on

[l][ ][Set ID][ ][OK][Data][x]

15. PIP Aspect Ratio (Command2:o)

G To select the PIP picture format.

You can also select the PIP picture format using WIN.SIZE on the remote control.

ransmission

[k][o][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: 4:3 1: 16:9

[o][ ][Set ID][ ][OK][Data][x]

16. Split Zoom (Command2:p)

G To operate split zoom function and select the split

zoom section number.

ransmission

Data Min: 21 ~ Max:99

•

Refer to ‘Real data mapping 2’.

[k][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

Real data mapping 2

21: Selection 1 of 2 split zoom 24: Selection 4 of 2 split zoom 41: Selection 1 of 4 split zoom 42: Selection 2 of 4 split zoom 44: Selection 4 of 4 split zoom 45: Selection 5 of 4 split zoom 91: Selection 1 of 9 split zoom

99: Selection 9 of 9 split zoom

Page 30

30 Plasma Display

External Control Device Setup

22. Red Adjustment (Command2:v)

G To adjust red in color temperature.

Transmission

Data Min: 0 ~ Max: C8

• Refer to ‘Real data mapping 3’ as shown below.

[k][v][ ][Set ID][ ][Data][Cr]

Acknowledgement

[v][ ][Set ID][ ][OK][Data][x]

23. Green Adjustment (Command2:w)

G To adjust green in color temperature.

Transmission

Data Min: 0 ~ Max: C8

• Refer to ‘Real data mapping 3’ as shown below.

[k][w][ ][Set ID][ ][Data][Cr]

Acknowledgement

[w][ ][Set ID][ ][OK][Data][x]

24. Blue Adjustment (Command2:$)

G To adjust blue in color temperature.

Transmission

Data Min: 0 ~ Max: C8

•

Refer to ‘Real data mapping 3’ as shown below.

[k][$][ ][Set ID][ ][Data][Cr]

Acknowledgement

[$][ ][Set ID][ ][OK][Data][x]

21. Color Temperature (Command2:u)

G To adjust color temperature.

You can also adjust ACC in the Picture menu.

ransmission

Data 0: Normal 1: Cool 2: Warm 3: User

[k][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

20. Balance (Command2:t)

G To adjust balance.

You can also adjust balance in the Sound menu.

ransmission

Data Min: 0 ~ Max: 64

•

Refer to ‘Real data mapping 1’. See page 28.

[k][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

18. Treble (Command2:r)

G To adjust treble.

You can also adjust treble in the Sound menu.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 28.

[k][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

19. Bass (Command2:s)

G To adjust bass.

You can also adjust bass in the Sound menu.

ransmission

Data Min: 0 ~ Max: 64

•

Refer to ‘Real data mapping 1’. See page 28.

[k][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

17. PIP Position (Command2:q)

G To select sub picture position for PIP.

You can also adjust the sub picture position using WIN.POSITION on the remote control or in the PIP/DW menu.

ransmission

Data 0: Right down on screen

1: Left down on screen 2: Left up on screen 3: Right up on screen

[k][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

Real data mapping 3

0 : -20 5 : -19 A : -18

5F: -1 64: 0 69: +1

C3: +19 C8: +20

Page 31

Owner’s Manual 31

External Control Device Setup

27. ISM Method (Command2:p)

G To avoid having a fixed image remain on screen.

ransmission

Data 0: Normal

1: White wash

2: Orbiter 3: Inversion

[j][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

28. Low Power (Command2:q)

G To control the low power function on/off.

ransmission

Data 0: Low power off

1: Low power on

[j][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

29. Orbiter Time Setting (Command2:r)

G To adjust orbiter operation time term.

ransmission

Data Min: 1 ~ Max: FE

[j][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

30. Orbiter Pixel Setting (Command2:s)

G To adjust pixel number in orbiter function.

Transmission

Data Min: 0 ~ Max: 9

[j][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

31. Picture Size Setting for Double Window mode (Command2:t)

G To adjust main window size in Double Window mode.

Transmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping 1’. See page 28.

[j][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

32. Auto Configure (Command2:u)

G To adjust picture position and minimize image shaking

automatically. It works only in RGB (PC) mode.

ransmission

Data 1: To set

[j][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

25. PIP Input Select (Command2:y)

G To select input source for sub picture in PIP mode.

Transmission

Data 0 : RGB

1 : Component 2 : Video

3 : S-Video 4 : DVI

[k][y][ ][Set ID][ ][Data][Cr]

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

26. Abnormal State (Command2:z)

G To recognize an abnormal state.

Transmission

Data 0: Normal (Power on and signal exist)

1: No signal (Power on) 2: Turn the monitor off by remote control 3: Turn the monitor off by sleep time function 4: Turn the monitor off by RS-232C function 5: 5V down 6: AC down 7: Turn the monitor off by Fan Alarm function 8: Turn the monitor off by off time function 9: Turn the monitor off by auto off function a: Turn the monitor off by AV board detect

Data FF:Read

[k][z][ ][Set ID][ ][FF][Cr]

Acknowledgement

[z][ ][Set ID][ ][OK][Data][x]

Page 32

32 Plasma Display

G Connect your wired remote control to the Remote Control port on the Monitor.

G Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

G Configuration of frame

G Repeat code

G Lead code

• 1st frame

Low custom code

Lead code

High custom code

Data code

Carrier frequency

CAR = 1/T

C = fOSC/12

Duty ratio = T1/T

C = 1/3

• Repeat frame

C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat code

9 ms 4.5 ms

0.55 ms

9 ms

2.25 ms

G Bit description

G Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

•

Bit “0”

Tf Tf

Tf=108ms @455KHz

0.56 ms 0.56 ms

1.12 ms

•

Bit “1”

2.24 ms

How to Connect

Remote Control IR Code

IR Code

Page 33

Owner’s Manual 33

IR Code

00H 01H 02H 03H 08H C4H C5H 09H 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 0BH 98H D5H C6H BFH 5AH D8H 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 77H AFH 99H

R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (Video/S-Video/Component/RGB/DVI) R/C Button (Component/RGB/DVI) Discrete IR Code (Input RGB Selection) Discrete IR Code (Input DVI Selection) Discrete IR Code (Input Component Selection) Discrete IR Code (Input Video Selection) Discrete IR Code (Input S-video Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (PIP/Double window Exchange) R/C Button (4:3/16:9) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (4:3/16:9/Zoom mode Selection) Discrete (Only 4:3 mode) Discrete (Only 16:9 mode) Discrete (Only Zoom mode) Discrete IR Code

Code (Hexa) Function Note

UP (D) DOWN (E) VOL+ (

VOL- (

POWER ON/OFF POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 INPUT SELECT MULTIMEDIA RGB DVI Component Video S-video SLEEP ENTER (Á) MENU DASP

APC

PIP PIP INPUT SWAP PIP ARC DW ZOOM + ZOOM Window Size Window Position

Split Zoom ARC ARC (4:3) ARC (16:9) ARC (Zoom) AUTO CONFIG

Page 34

34 Plasma Display

Troubleshooting Checklist

No output from one of

the speakers

• Adjust Balance in the SOUND menu. (Refer to p.17)

Unusual sound from

inside the monitor

• A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the monitor.

No picture &

No sound

• Check whether the Monitor is turned on.

• Power cord inserted into wall outlet?

• Test the wall power outlet, plug other product’s power cord into the wall outlet where the Monitor’s power cord was plugged in.

No or Poor color

or Poor picture

• Select Color in the PICTURE menu and press the VOLUME (G) button. (Refer to p.16)

• Keep a sufficient distance between the Monitor and the VCR.

• Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.)

The remote control

doesn’t work

• Check to see if there is any object between the Plasma Display and the remote control causing obstruction.

• Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.8)

• Install new batteries. (Refer to p.8)

Picture OK &

No sound

• Press the VOLUME (G) button.

• Sound muted? Press MUTE button.

Picture appears slowly

after switching on

• This is normal as the image is muted during the startup process of the monitor. Please contact your service centre, if the picture has not appeared after five minutes.

Horizontal/vertical bars

or picture shaking

• Check for local interference such as an electrical appliance or power tool.

TTroubleshooting Checklist

roubleshooting Checklist

Page 35

Owner’s Manual 35

Maintenance & Specification

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.

If you expect to leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Cleaning the Cabinet

Extended

Absence

Maintenance

Page 36

36 Plasma Display

Specification

• The specifications shown above may be changed without notice for quality improvement.

Product Specifications

MODELS

Width (inches / mm)

Height (inches / mm)

Depth (inches / mm)

Weight (pounds / kg)

Power requirement

Resolution

Color

Operating Temperature Range

Operating Humidity Range

Maximum Elevation

MU-42PZ44/44A/44B/44K/44R/44S MU-42PZ44M/44MA/44MB/44MK/44MR/44MS MU-42PZ44V/44VA/44VB/44VK/44VR/44VS MU-42PZ90/90A/90B/90K/90R/90S MU-42PZ90M/90MA/90MB/90MK/90MR/90MS MU-42PZ90V/90VA/90VB/90VK/90VR/90VS MU-42PZ90C

40.7 / 1033

24.5 / 622

3.2 / 81

75 / 34

AC100-240V ~ 50/60Hz

852 x 480 (Dot)

16,770,000 (256 steps of each R, G and B)

32 ~ 104°F (0 ~ 40°C)

Less than 80%

6561 feet (2000m)

Page 37

Owner’s Manual 37

Notes

Page 38

38 Plasma Display

Notes

Page 39

Owner’s Manual 39

Notes

LG 90VR, 90VA, 90M, 90MK, U-42PZ44 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual