<![endif]>ENGLISH
OWNER'S MANUAL
WASHING
MACHINE
Please read this manual carefully before operating
washing machine and retain it for future reference
T65SJ* |
T65SN* |
T65SP* T7288* |
T70SJ* |
T70SN* |
T70SP* |
T80SJ* |
T80SN* |
T80SP* |
T90SJ* |
|
|
T10SJ* |
|
|
MFL68486520 |
www.lg.com |
|
Copyright © 2020-2021 LG Electronics Inc. All Rights Reserved. |
||
Rev.01_071220 |
Contents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you
may not need to call for service at all.
Page No
Introduction
Installation
Before Starting to Wash
Safety Information |
3 |
Product Feature |
6 |
Identification of Parts |
7 |
Placing, Leveling & Installation |
8 |
Connecting water supply Hose & Drain Hose |
9 |
Preparation Before Washing |
11 |
Use of Water, Detergent, Bleach and Softener |
12 |
Special Guide for Stain Removal |
15 |
Control Panel |
16 |
Washing Programs
Additional Function
Program
Care and Maintenance
Troubleshooting
Installation Check sheet Terms of Warranty
Features & Specifications
Other Useful Functions |
17 |
Normal |
18 |
Quick Wash |
18 |
Gentle (Wool/Saree) |
19 |
Turbo Wash |
19 |
Strong ( Jeans) |
19 |
Tub Clean |
19 |
Aqua Reserve Wash |
19 |
Pre Wash+ Normal Wash |
20 |
Favourite Wash |
20 |
AIR DRY |
20 |
ENERGY SAVING GUIDE |
21 |
Smart Closing Door |
22 |
Soak Wash |
22 |
Option Washing |
23 |
DELAY START (RESERVATION) Wash |
24 |
Cleaning and Maintenance |
25 |
Common Washing Problems |
27 |
Troubleshooting |
28 |
Earthing |
29 |
Smart DiagnosisTM |
29 |
Disposal of old appliance |
31 |
Installation Check sheet |
32 |
Warranty |
33 |
Features & Specifications |
35 |
* Product feature may vary according to different models. Refer page 35 for modelwise
features for your purchased model.
2
Safety Information
Read carefully and thoroughly go through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
WARNING
CAUTION
:Failure to comply with the instructions under this sign may result in major physical injuries or death.
:Failure to comply with the instructions under this sign may result in minor physical injuries or damages to the product.
Disclaimer : The user should follow the instructions as per the owner’s manual to avoid
any malfunctioning of the product, accident or damage.
The manufacturer is not liable for any accident or consequential or resulting liability, damage or loss to property or life arising directly or indirectly from the product. The manufacturer's liability is limited only to the extent of repair or replacement of the product as per the terms and condition mentioned elsewhere in the document.
WARNING
•Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
PROPER
INSTALLATION CAUTION
•Machine must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.
•Washer shall be placed in dry areas specifically during rainy season.
Humid conditions may cause rusting which may result in product failure.
•The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
•Install or store where it will not be exposed to temperature below freezing or exposed to the weather (Rain/Water Splash/ Direct Sunlight).
If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.
3
Safety Information
WARNING
•Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger explosion or fire.
•Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
YOUR |
Do not touch the Power Plug with a wet hand. |
LAUNDRY |
It will cause electric shock |
AREA |
|
CAUTION
Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
• Do not put or keep any magnet near Lid of Washer, it will result in Malfunctioning of the Product.
|
Children should be supervised to ensure that they |
|
do not operate or play with the appliance. Inconstancy to this may damage machine, |
WHEN USING |
serious injury and electrical shock. |
THE WASHER |
Do not use power plug, power socket outlet and wiring equipment for |
|
more than their rated capacity. |
|
for laundry |
|
or Tub Wash. |
4
Safety Information
WARNING
•Disconnect the Washer from the household distribution panel by removing the Power Plug from Power Socket outlet before attempting any maintenance or cleaning
Inconstancy to this may Cause electrical shock
•Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded.
Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
•If, during spinning, opening the lid does not stop the tub within about 15 second, immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into the machine while it is running.
Wait until the machine has completely stopped before opening the lid.
WHEN USING
Even slow rotation can cause injury.
THE WASHER
Never attempt to operate this appliance if it is damaged, malfunctioning, partially
disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
CAUTION
Do not use washer for any other purpose other than its intended purpose.
- Use this appliance only for household purpose.
Do not use water hotter than 60°C.
Do not connect washer to hot water supply.
Use of excessively hot water may cause damage to fabrics or cause
leakage of water.
Ensure No water logging near or below washer to prevent rusting.
Rusting on certain parts may result in product failure
WARNING
Customer may Slip too.
Using unclean power socket plug may cause fire.
WHEN NOT
IN USE
Do not use wet cloth to clean the machine, Always use dry cotton cloth.
Turn off the water faucets to relieve pressure on hoses; they may need Replacement after 5 Years Inconstancy to this may rupture hose which leads to water Leakage.
5
Product Features
Washer doesn't operate while the lid is opened. If the lid is opened during the wash, rinse or spin cycles, the operation stops for safety.
Pre Wash+ Normal
• The purpose of this program is to deliver best Wash Performance by adding extra 8 min of uniquely designed washing pattern before the main wash cycle.
Jet Spray+#
• A technology uniquely designed to spray inlet water with greater force to penetrate deep into the clothes to bring out the best washing and rinsing performance.
Smart Closing Door
• Smart hinge prevents sudden closing of the door. Gives you a soft and safe door closing.
Turbowash*
• Turbowash program delivers high wash performance in least cycle time using revolutionary Jetspray+ technology which optimizes water & energy consumption.
Normal logic control
• A built-in load sensor automatically detects the laundry |
|
SENSING |
SETTING |
|
AUTO |
|
load and a microprocessor optimizes washing conditions |
START |
WASHING |
||||
Water Level Sensor |
Washing |
POWER |
||||
|
|
Laundry Sensor |
Optimum |
|
|
|
such as ideal WATER LEVEL and washing time. |
|
|
Condition |
|
OFF |
|
|
|
|
|
|
• Advanced technology is built into the Electronic Control System which ensures the best washing result.
TurboDrum washing
• When "Punch + 3" washing wings turn, the washing tub turns in the opposite direction. This makes the both sides current of water which improve wash-performance by rubbing clothes strongly.
3 Step washing
• 3 step washing makes the best washing performance with low tangling.
Rubbing |
Rubbing and |
Shaking and |
|
Shaking |
Disentangling |
Smart Diagnosis
• It is the technology to transmit the anomalies to the service center when there is a problem with the washer. It provides the service that gives faith and trust to the customers through precise and fast analysis.
Auto Restart
• Auto Restart allows the program to restart all by itself in case of power failure. It resumes from stage where it stopped, however, the wash cycle time may vary.
#Works during Wash cycle in Normal, Pre Wash+ Normal, Turbo Wash & Aqua Reserve from WL1 to 7 and during Rinse cycle in Normal, Pre Wash+ Normal, Turbo Wash & Aqua Reserve Programs at all water levels.
Jet Spray performance may vary with Inlet water pressure, for optimum results pressure should be > 0.9 Bar
* Product feature may vary according to different models. Refer page 35 for modelwise features for your purchased model.
6
Identification of Parts
Body
Smart Hinge
POWDER |
DETERGENT BOX |
MAGIC FILTER
Clean regularly to
stop linting on the
clothes load.
SOFTENER
INLET
BLEACH
DISPENSER
FUNCTION
SELECTOR
TUB
START/PAUSE
BUTTON
Use to start or
stop the washing
machine
temporarily.
ADJUSTABLE LEGS
Use to level the washing machine for correct balance & spin operation.
WATER SUPPLY
HOSE
Make sure the
water does not
leak.
POWER PLUG
If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.
JET SPRAY NOZZLE
Depending upon the Inlet Water Pressure, performance of Jet Spray may vary.
(Works in Normal, Turbo Wash,
Pre Wash+ Normal & Aqua
Reserve Wash Programs).
CASTORS
Use for easy translocation
(at rear bottom edge)
DRAIN HOSE
Keep the drain hose flipped down while washing is in progress.
BASE
Accessories
Water supply hose |
Drain hose |
Anti-rat cover |
For Cold Water
Snap Ring
NOTE
“ ” Parts can be different as per purchased model.
Please do not match this figure with model as it may be different from your model .These are schematic diagrams only.
Due to continuous improvements at LG, specification of washing machine are subject to change without prior notice.
7
lacing, Leveling and Installation
Improper installation of the washer may cause noise and malfunctioning.
Note : 1. |
The ventilating openings in the base area must not be obstructed by carpeting when the washing machine is |
||
|
installed on a carpeted floor. |
1 Installation area |
|
2. |
Install the washing machine on a level and firm |
||
|
surface. |
Install the washer on flat and firm surface. |
|
3. |
Handle all packaging materials (such as plastic |
||
|
bags and thermacol) to keep away from children. The packaging materials can cause suffocation.
How to adjust leveling
Adjustable leg
Turn the adjustable legs to set the washer
horizontal (Both the front legs).
H Don't add anything under back side legs.
Distance between drain hose and the wall
Distance between drain hose and the wall should be more than 10cm, and the distance between the other part or the rear part and the wall should be more than 2 cm. .
More than 10cm
More than 2cm
More than 2cm
2
The Basement is not flat, fill the water just touching the Pulsator and see uniform distribution. If not, adjust the legs as shown in the figure.
Top View
3 Checking Proper placement
Press the corners of the machine diagonally
as shown in the figure, If any movement is observed, adjust the legs for proper leveling.
|
# Moving of the Machine |
Anti-rat cover installation |
Casters are provided for easy translocation of your machine |
|
* Grip the machines properly as shown in fig. |
Insert the Anti rat cover firmly from back side side of washing machine. |
* Tilt the machine towards your side at a angle |
45 O~ 55 .O |
Casters
Note : * Be careful that you should not drop the machine.
* Never move the machine on casters when there is load inside.
Be sure to remove the product from the carton base, otherwise the machine will not be able to operate
properly.
#Product feature may vary according to different models. Refer page 35 for model wise features for your purchased model. Please do not match the figures with model as it may be different from your model. These are schematic diagrams only.
8
C onnecting Water Supply Hose & Drain Hose
Water Supply Hose
Normal Type (Normal tap without thread & one touch type inlet hose.)
1Separate Middle connector from Water Supply Hose
Separate Middle connector from the Water Supply Hose by pulling the Pressing Rod and the Pressing Handle that is attached to the Water Supply Hose.
Middle |
|
connector |
Pressing Handle |
Pressing Rod
Water Supply Hose
2Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the |
Rubber packing |
tap can be placed in the middle. |
screw |
NOTE
In case tap is too large.
If the tap diameter is too large or is square, untighten the 4 screws and remove the guide plate. Then follow step1.
Guide plate
Rubber packing
3 Fixing Connectors to the Tap
Connector
Push the upper connector up till the rubber packing is in tight contact with the tap. Then
tighten the 4 screws
.
4Fixing Upper Connector and Middle Connector
Remove the fixed sticker in between the Upper and Middle Connectors. Tighten the connectors by holding one connector and twist middle connector to the right.
Connector
Middle
Connector
Connector Middle
Connector
5 |
Connecting Middle Connector and Water Supply Hose |
Press down the pressing rod of the Water Supply Hose which was separated from middle connector (refer to Step1) and then join it to the middle connector.
Pressing rod Pressing handle
Water Supply Hose
6Check for water leakage
After connecting the other end of hose to machine open the tap to check for any water leakage.
If the connection leaks, close the tap and start again from step 1.
If you skip step 1, water leakage may occur.
9
After connecting inlet hose to water faucets, turn on the water faucets to flush out foreign substances (dirt, sand, or sawdust) in the water lines. Let water drain into a bucket, and check the water condition.
For your safety and for extended product life, use only authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized parts.
Use new hoses when you install the washing machine. Do not reuse old hoses. Use only the inlet hoses provided with the washer . LG does not recommend the use of aftermarket hoses.
Periodically check the hoses for cracks, leaks and wear, and replace the hoses every 5 years.
Do not stretch the water hoses intentionally, and make sure that they are not crushed by other objects.
Connecting Water Supply Hose to Washer
Check to see if there is a rubber seal inside the connector.
Connect the water supply hose to inlet valve of the washing machine, and then lock it by turning the hose connecting part.
Drain Hose
Connecting the Drain Hose to Washer
Insert the drain hose to the connect- |
2 |
1. Press the hose clip. |
1 ing area at the body. |
2. While pressing, push the hose towards |
the body.
3. Release the hose clip after pushing the hose.
Less than 10cm
The hose is placed over a doorsill.
The hose is clogged by alien substances.
Make sure that the hose is not crushed.
Make sure that the hose is not crushed between the wall and the washer
Avoid submerging the end of hose.
If Extension hose is used should be less than 3m
10
Preparation Before Washing
Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.
Sort clothes into loads that can be washed with the same wash cycle.
Sorting
To get the best results, different fabrics need to be washed in different ways.
• SOIL (Heavy, Normal, Light) |
Separate clothes according to th e type and amount of soil. |
• COLOR (Whites, Lights, Darks) |
Separate white fabrics from colored fabrics. |
• LINT (Lint Producers, Collectors) Separate lint producers and lint collectors. |
|
Lint Producers |
Terry cloth, Towels, Nappies, Diapers |
Lint Collectors |
Synthetics, Socks |
Check before Loading
• Check all pockets to make sure that they are emtpy. Things such as nails, hairclips, matches, pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains. |
WIRE |
|
•Make sure the clothes are washable in water.
•Check the washing instructions.
•Remove tissue from pockets.
CAUTION
Do not wash or spin any item labeled or known to be water-proof or water-resistant, even if the product care label on the item
permits machine washing. Failure to follow these instructions could result in severe damage to your laundry, your washer and/or
property damage as a result of abnormal vibration of the washer.
-Examples of water-proof or water-resistant items include certain mattress pads, mattress covers, rain gear, camping gear, skiing apparel, outdoor gear and similar items.
Pretreatment on stains or heavy soil
•Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
•Use a pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.
(For more detail refer to page15)
Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.)
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes not higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.
WARNING
Fire Hazard
Never place items in the washer that are dampened with gasoline or other flammable fluids. No washer can completely remove oil. Do not dry anything that has ever had any type of oil on it (including cooking oils). Doing so can result in death, explosion, or fire.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net* and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets*for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
* Nylon net is not supplied by LG.
11