LG T70CPD22N Owner’s Manual

(refer to page 21)

SOAK

INDIA'S

(refer to page 22)

Time Left

N o. 1

WASHI NG M ACHI NE

P/No.: MFL60983102

Owner's Manual

Please read this manual carefully and thoroughly before operating this unit.

Record model name and serial number of the set. Quote this information to your dealer when you

require service.

MODEL : WF-N7069NN

WF-N7069NP WF-N7039NP

T70CPD22N

roduct Features

Washer doesn't operate while the lid is open. If the lid is open during the wash, rinse or spin cycles, the operation stops for safety.

FUZZY logic control

A built-in load sensor automatically detects the laundry load and a microprocessor optimizes washing conditions such as ideal WATER LEVEL and washing time.

SENSING

SETTING

Laundry Sensor

Water Level Sensor

Optimum Washing Condition

WASHING

START

Advanced technology is built into the Electronic Control System which

AUTO

POWER

OFF

ensures the best washing result.

Turbo drum washing

When "Punch + 3" washing wings turn, the washing tub turns in the opposite direction. This makes the both sides current of water which improve wash-performance by rubbing clothes strongly.

3 Step washing

3 step washing makes the best washing performance with low tangling.

Rubbing

Be sure to remove the unit from the carton base, otherwise the

NOTE

Rubbing and

Shaking

machine will not be able to operate properly.

Shaking and

Disentangling

ontents

READ THIS MANUAL

Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.

Introduction

Before Starting to Wash

Washing Programs

Additional Function Program

Installation

Care and Maintenance

Troubleshooting

Specification

Installation Check Sheet Terms of Warranty

Safety Information 4

Identification of Parts 7

Function Information 8

Preparation Before Washing 9

Use of Water, Detergent, Bleach and Softener

Special Guide for Stain Remova

l 13

Function of each Button 14

SOAK Wash 16

ash (Normal )

W Wash 17

FUZZY

L Wash 17

WOO

WASH 17

QUICK

JEANS Wash 17

SILENT Wash 19

Option Washing 20

DELAY START (RESERVATION) Wash 21

Other Useful Functions 22

Placing and Leveling 23

Connecting Water Supply Hose 24

Connecting Drain Hose 25

Grounding Method 26

Cleaning and Maintenance 27

Common washing problems 29

Troubleshooting 30

Specification

Installation Check Sheet Terms of Warranty

afety Information

Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts : Warning and Caution.

: This is a warning sign specifying user’s applications which might be dangerous.

: This is a sign specifying ‘Strictly Forbidden’ applications.

WARNING

CAUTION

WATER HEATER SAFETY

PROPER INSTALLATION

: Failure to comply with the instructions under this

sign may result in major physical injuries or death.

: Failure to comply with the instructions under this sign may result in minor physical injuries or damages to the product.

WARNING

Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances. If the HOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water fa ucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. S ince the gas is flammable, do not smoke or use an open flame or appliance during this process.

CAUTION

•

The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

•

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather (Rain / Water Splash).

If the product is exposed to such conditions,electric stock, fire, break down or deformation may occur.

•

Properly ground washer to conform with all governing codes and ordinances. Follow details in Installation Instructions.

If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.

•

Must be positioned so that the plug is accessible.

If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.

•

Make sure the plug is completely pushed into the outlet.

Failure to do so may cause electric shock and fire due to overheating.

•

Do not connect ground to a gas pipe.

It can cause explosion.

•

Do not connect ground to telephone wires or lightning rods.

This may be dangerous during electrical storms.

•

Washer shall be placed in dry areas specifically during rainy season.

Humid conditions may cause rusting which may result in product failure.

afety Information

YOUR LAUNDRY AREA

WHEN USING THE WASHER

WARNING

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.

Operating with such materials around the machine may trigger explosion or fire.

• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.

There is potential danger that children might drown in the tub.

Do not touch the power plug with a wet hand.

It will cause electric shock

Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.

There is a rotating mechanism under the machine, so you could be injured.

CAUTION

• Use this appliance only for its intended purpose as described in this Owner’s Manual.

• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

NOTE : Pressing Power button to turn off does NOT

disconnect the appliance from the power supply.

• Make sure that drainage is working properly.

If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.

• If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving. Wait until the machine has completely stopped before opening the lid.

Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

Operating with a damaged plug may cause electric shock.

Do not use water hotter than 60°C.

Use of excessively hot water may cause damage to fabrics or cause leakage of water.

Ensure No water logging near or below washer to prevent rusting.

Rusting on certain parts may result in product failure

afety Information

WHEN USING THE WASHER

WHEN NOT

IN USE

WARNING

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Do not use a plug socket and wiring equipment for more than their rated capacity.

Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.

Do not mix chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acids (such as vinegar) or product containing ammonia.

Mixing different chemicals can produce toxic gases which may cause death.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation.

It may ignite or explode.

CAUTION

• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage

if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.

• When the air temperature is high and the water temperature is low, condensation may

occur and thus wet the floor.

• Wipe off dirt or dust on the contacts of the power plug.

Using unclean power plug may cause fire.

• Before discarding a washer, or removing it from service, remove the washer lid to

prevent children from hiding inside.

Children may be trapped and suffocated if the lid is left intact.

Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published userrepair instructions that you understand and have the skills to carry out.

Operating the machine with improperly replaced parts may be a cause for fire or electric shock.

Do not tamper with controls.

It may lead to electric shock, fire , break down, deformation.

Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.

Failure to observe these instructions may cause electric shock or fire due to shortcircuit .

When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.

It will cause short circuit and electric shock.

Customer Information Center

For any query related to the after sales service you may please contact us on the numbers listed below :

LG Electronics India Pvt. Ltd.

Regd. Office : A-27, Mohan Co-operative Industrial Estate, Mathura Road, New Delhi-110044

LG ELECTRONICS INDIA PVT. LTD. CUSTOMER CARE CENTRE

dentification of Parts

Body

POWDER DETERGENT

Box for delayed washing.

** LINT FILTER / MAGIC FILTER

Clean regularly to stop linting on the clothes load.

BLEACH DISPENSER

FUNCTION SELECTOR

TUB

START/PAUSE BUTTON

Use to start or stop the washing machine temporarily.

ADJUSTABLE LEG

Use to level the washing machine for correct balance & spin operation.

(2 adjustable legs are optional, some models have provision for 1 adjustable leg)

Accessories

Water supply hoses

NOTE

"*" Parts can be different according to the model. "**" LINT FILTER (Applicable for WF-N7069NN/WF-N7069NP) MAGIC FILTER (Applicable for WF-N7039NP, T70CPD22N)

Drain hose

Snap Ring

WATER SUPPLY HOSE

Make sure the water does not leak.

POWER PLUG

If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.

CASTORS

Use for easy translocation

DRAIN HOSE

Keep the drain hose flipped down while washing is in progress.

BASE

Anti-rat cover

Screw

unction Information

Our machine provides various washing methods which suits variou and types of laundry.

Different types of laundry washing

FUZZY(Normal)

Use this Program for everyday washing e.g. sheets, towels, T- shirts.

Wash

(refer to page 17)

JEANS Wash

Use this Program for heavily soiled durable garments e.g. overalls, jeans Thick and heavy clothes or those which are excessively dirty like jeans or working uniformscan be washed (refer to page 17)

WOOL Wash

Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 17)

The fibers of machinewashable woolens have been specifically modified to prevent felting when they are machine washed. Most handknitted garments are not made of machine washablewool and we recommend that you hand wash them

• Before washing your woolens check thecare label for the washing instructions.

• When washing woolens usea mild Detergent recommended for washing wool.

• Hand washed woolens may bespun in a washing machine to reduce the time they take to dry.

• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.

(The heat and tumbleaction of a dryer may causeshrinkage or felting of woolen garments. Some wool underlaysand sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to handwash thesearticles and place them in the machine to spin dry.

)

Washing according to the condition of laundry

QUICK WASH

QUICK WA SH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 17)

SOAK Wash

SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 16)

Other washing method

DELAY START Wash

DELAY START Wash is used to delay the finishing time of the operation. The number of hours to be delayed can be set by the user accordingly. (refer to page 21)

OPTION WASH

When the user needs only SPIN, RINSE/SPIN, RINSE, WA SH/RINSE, WA SH, WASH/RINSE/SPIN, SOAK/WA SH/RINSE/SPIN. (refer to page 20)

s conditions

reparation Before Washing

Care Labels

* Look for acare label on your clothes This will tell you about the fabric content of your garment

and how it should be washed. Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

Sorting

To get the best results, different fabrics need to be washed in different ways.

• SOIL (Heavy, Normal, Light) COLOR (Whites, Lights, Darks)

•

LINT (Lint Producers, Collectors)

•

Lint Produ cers Lint Collectors

Check before Loading

• Check all pockets to make sure that they are emtpy. Things such as nails, hairclips,, matches, pens, coins, and keys can damage both your washer and your clothes.

• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.

• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.

• Pretreat any dirt and stains.

• Make sure the clothes are washable in water.

• Check the washing instructions.

• Remove tissue in pockets.

Pretreatment on stains or heavy soil

• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

• Use a pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.

(For more detail refer to page13)

Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.)

Load Size

The WATER LEVELF should just cover the clothes. Adjust the load size accordingly. Loosely load clothes not higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.

Light and Large-sized clothing

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Long laundry items

Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing.

Nylon net is not supplied by LG.

Fasten zippers, hook, and stringsto make sure that these items don't snag on other clothes.

Separate clothes according to the type and amount of soil. Separate white fabrics from colored fabrics. Separate lint producers and lint collectors.

Terry cloth, Chenille Towels, Nappies, Diapers Synthetics, Corduroy, P ermanent Press, Socks

WIRE

se of Water, Detergent, Bleach and Softener

Using Water

Amount of WATER LEVEL

• This machine detects the quantity of laundry automatically, then sets the WATER LEVEL and proper amount of Detergent.

• When you select a wash program, the WATER LEVEL will be shown on

the control panel.

• The following table shows the amount of water.

• When the WATER LEVEL is automatically detected, it may differ depending

on the quantity of laundry even though the same WATER LEVEL is indicated on the control panel.

Using Detergent

Detergent

Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems. Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.

Choosing the right Detergent

We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to us Detergent suitable for washing woolens.

Water Level and Amount of Detergent

Concentrated detergent: 20g per 30 liters of water.

Regular synthetic detergent: 30g per 30 liters of water.

When sensing water levels automatically, the amount of detergent can differ according to the amount of laundry even at the same water level.

For synthetic detergent, use one that generates less

bubbles. This type of detergent is specially designed for washers

In case of using liquid detergent, dissolve it with water (detergent: water =1:1) and deposit it through the bleach deposit hole

Note : To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not cotribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine. If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental pollution, so use it accordingly.

Water

Amount

Level

of Water

65 l

61 l

51 l

42 l

38 l

34 l

32 l

29 l

23 l

*Rated Capacity of Model

Amount

of laundry

Less than*

Less than 4.0kg

Less than 3.5kg

Less than 3.0kg

Less than 2.5kg

Less than 2.0kg

Less than 1.5kg

Less than 1.0kg

Less than 0.6kg

Less than 0.3kg

Amount of Detergent

Regular

Concentrated

synthetic

About 45g

About 65g

About 39g

About 58g

About 38g

About 57g

About 33g

About 49g

About 29g

About 44g

About 25g

About 38g

About 22g

About 33g

About 19g

About 28g

About 16g

About 24g

About 13g

About 20g

Adding the detergent

Open the detergent dispenser and deposit the appropriate amount of detergent where you deposit the detergent Powder Detergent dispenser.

Some detergents MUST be fully dissolved before adding to your machine to get the best wash results. Check the instructions on the detergent packet. If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water before being added to warm or hot water for the actual wash. Pre-dissolving detergent in warm water when washing in cold water can improve its performance.

Where you deposit the

Using Liquid Bleach

• Check clothing care label for special instructions and separate the laundry to be bleached

• Dilute liquid chlorine bleach.

• Measure the recommended amount of liquid bleach carefully

following instructions on the bottle.

• Before starting the washer, pour measured amount of bleach directly into bleach dispenser. Avoid splashing or overfilling. Powdered bleach should be mixed with water before pouring

NOTE

n Never pour undiluted liquid bleach directly onto clothes or into the wash basket.

This may cause change of color or damage the laundry

n Do not pour powdered bleach into bleach dispenser.

detergent

Powder Detergent Box

Bleach dispenser

se of Water, Detergent, Bleach and Softener

Using Fabric Softener

• Dilute fabric softener with water. Undiluted fabric softener may result in spots that look like oil stains.

• Measure and add the recommended amount of fabric softener into the compartment marked with thissymbol( ). Follow manufacturer’s direction.

Fabric softener is automatically dispensed in the final rinse with indication beep.

If you want extra rinse, you must add fabric softener manually when indication beep rings in the final rinse. This maximize the fabric softener function.

• Do not overfill. The dispenser hold max 35ml. Never add more than 35ml. Overfilling can cause early dispensing of the fabric softener which could result in stained clothes. A cup with a pouring spout will help you avoid spilling.

• The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric softener has to be diluted with water before dispensed and never poured directly on clothes.

Attention

Do not mix with detergent or bleach.

•

Never pour fabric softener directly on clothes. It may stain them.

•

Do not stop the washer during the first spin for timely dispensing.

•

Option washing is not designed to be used with fabric softener dispenser.

•

Scrud (Waxy Build up)

Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.

If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.

If you wish to use fabric softener we recommend

• Using fabric softener sparingly.

• When filling the dispenser, do not splash or overfill.

• Clean dispenser as soon as the cycle is finished.

• Clean your machine regularly. (refer to page 28)

• Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or

HOT wash e.g. every 5th wash should beat least a warm one.

• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.

Softener dispenser( )

pecial Guide for Stain Removal

For successful stain removal:

• Remove stains promptly.

• Determine the kind of stain, then follow the recommended treatment in thestain

removal chart below.

• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.

• Use COLD water on unknown stains because HOT water can set stains.

• Check care label instructions for treatments to avoid on specific fabrics.

• Check for colorfastness by testing stain remover on an inside seam.

• Rinse and wash items after stain removal.

STAIN

Adhesive tape, chewing gum, rubber cement

Baby formula, dairy products, egg

Beverages (coffee, tea, soda, juice, alcoholic beverages)

Blood

Candlewax, crayon

Chocolate

Collar or cuff soil, cosmetics

Dye transfer on white fabric

Grass

Grease, oil, tar (butter, fats, salad dressing, cooking oils, car grease, motor oils)

Ink

Mildew, scorch

Mud

Mustard, tomato

Nail polish

Paint, varnish

Rust, brown or yellow discoloration

Shoe polish

Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonflammable dry cleaning fluid.

Use product containing enzymes to pretreat or soak stains.

Pretreat stain. Was h using COLD water and bleach safe for fabric.

Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using bleach safe for fabric.

Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.

Pretreat with prewash stain remover or rub with bar soap.

Use packaged color remover. Wash using bleach safe for fabric.

Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.

Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wa sh using hottest water safe for fabric

Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or nonflammable dry cleaning fluid

Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly mildewed fabrics ma

Brush off dry mud. Pretreat or soak with product containing enzymes.

Pretreat with prewash stain remover. Wash using bleach safe for fabric.

May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain. Repeat, replacing paper towels frequently. Do not use on acetate fabrics.

WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL BASED & VARNISH : Use solvent recommended on can label. Rinse thoroughly before washing.

For spots, use rust remover safe for fabric.For discoloration of an entire load, usephosphateDetergent and nonchlorine bleach.Do not use chlorine bleach because it may intensify discoloration.

LIQUID : Pretreat with apaste of granular Detergent and water. PASTE : Scrape residue fromfabric. Pretreat with prewash stainremover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach safe for fabric.

Stain Removal

y b

e permanently damaged.

TREATMENT

Follow fabric care label

instructions

Press the PROGRAM button to select the SOAK Program.

Select washing time by pressing the Wash button repeatedly. (Wash timing cannot be set to zero in SOAK Program)

Press the RINSE button to select the desired no. of rinse cycles.

lacing, Leveling and Installation

Improper installation of the washer may cause noise and malfunctioning.

Note :

The ventilating openings in the base area must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. Install the washing machine on a level and firm

2. surface, any tilt should be less than 4°.

How to adjust leveling

Adjustable leg

Turn the adjustable legs to set the washer horizontal (Both the front legs).

Don't add anything under back side legs.

Distance between drain hose and the wall

Distance between drain hose and the wall should be more than 10cm, and the distance between the other part or the rear part and the wall should be more than 2 cm.

More than 2cm

More than 10cm

Anti-rat cover installation

Insert the anti rat cover firmly from back side or Front side of washing machine and screw it.

High Base

Middle Base

Low Base

FIXING POSITION

Adjustable Leg

Screws

Anti Rat Cover

Installation area

Install the washer on flat and firm surface.

Checking level

The Basement is not flat, fill the water just touching the Pulsator and see uniform distribution. If not, adjust the legs as shown in the figure.

Top View

Checking Proper placement

Press the corners of the machine diagonally as shown in the figure, If any m ovement is observed, adjust the legs for proper leveling.

When you want to only drain, press SPIN button.

Then press START/PAUSE button.

Wait until the water in the washing tub drains completely and then press POWER button to finish the activity.

Time Left

Time LeftTime Left

Press both the SPIN button and the DELAY button simultaneously.

Time Left

SPIN DELAY

If you want to unlock during wash, press both the SPIN and the DELAY button simultaneously again.

To see the remaining time for each process, first press START/PAUSE button and then press one of the WASH, RINSE and SPIN buttons.

onnecting Water Supply Hose

Normal Type

Separate Middle connector from Water Supply Hose

Separate Middle connector from the Water Supply Hose by pulling the Pressing Rod and the Pressing Handle that is attached to the Water Supply Hose

Loosen the fixed nuts to connect the connector to the tap

Untighten the screw of the connector so that the tap can be placed in the middle.

NOTE

In case tap is too large.

If the tap diameter is too large or issquare, untighten the 4 screws and remove the guide plate. Then follow step1

Fixing Connectors to the Tap

Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws.

Fixing Upper Connector and Middle Connector

Remove the fixed sticker in between the Upper and Middle Connectors. Tighten the connectors by holding one connector and twist middle connector to the right.

Connecting Middle Connector and Water Supply Hose

Press down the pressing rod of the Wa ter Supply Hose which was separated from middle connector (refer to Step1) and then join it to the middle connector.

Check for water leakage

After connecting the hose, open the tap to check for any water leakage. If the connection leaks, close the tap and start again from step 1. If you skip step 1, water leakage may occur.

(Normal tap without thread & one touch type inlet hose.)

Middle connector

Water Supply Hose

Guide plate

Connector

Fixed sticker

Pressing rod

Fixed Sticker Pressing Handle

Pressing Rod

Water Supply Hose

Rubber packing

Middle Connector

Rubber packing screw

Fixed sticker

Connector Middle Connector

Pressing handle

onnecting Drain Hose

Befor e c onnect ing Drai n Hose, c heck you r D rain Hos e model an d choos e t he corre ct instructions.

How to connect the drain hose

Insert the drain hose to the connecting area at the body.

1 2

Less than 6cm

Less than 2m

The hose is placed over a doorsill.

The hose is clogged by alien substances.

Make sure that the hose is not crushed.

Less than 3m

Extension hose is used.

Press the hose clip.

While pressing, push the hose towards the body. Release the hose clip after pushing the

3. hose.

Less than 10cm

Make sure that the hose is not crushed between the wall and the washer

Avoid submerging the end of hose.

rounding Method

Earth wire should be connected.

the earth wire is not connected, there is possible a danger of electric shock caused

If by the current leakage.

Grounding Method with Ground insert space Terminal

If the ACcurrent outlet has a ground terminal, then separate grounding is not required.

Concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Other Grounding Metho

Burying Copper Plate

Connect the Ground Wire to a Ground Copper Plate and bury it more than 75cm in the ground.

Using Ground Wire

Connect the ground Wire to the socket provided exclusively for Grounding.

Ground Copper Plate

Ground Wire

Using a Short Circuit Breaker

If grounding methods described above are not possible, a separate circuit breaker should be employed and installed by a qualified electrician

Ground terminal

Short-circuit breaker

Grounding is not needed

Ground Wire

75cm

To Clean the Magic Filter

If the magic filter is damaged, purchase a new one from LG Authorised Service Center.

To Clean the Lint Filter

Press and then pull forward the lint filter from the washing tub to the arrow direction.

Press & Pull

When the lint filter is worn out, etc., contact a LG Service Center for a new one.

Turn inside out and wash it to remove dirt.

Insert it back into same place and push until click sound heard.

Push

This LG Washing Machine comes with 2 year warranty, from the date of purchase, that comprises of a 2 year warranty on all Parts except Lint filter, knobs, inlet/outlet hose & Top Covers, subject to that the warranty card bears the rubber stamp, date and signature of our Authorized Dealer.

Terms & Condition

1. The warranty is confined to the first purchaser of the Washing Machine only & is non-transferable.

2. Repairs & replacements will be carried out by the dealer from whom the product has been purchased, or through the Authorized Service Centers of LGEIL. In case the customer shifts the place of residence during warranty period, it is advised to contact Authorized Service Centre directly or call our help line.

3. Repairs under warranty shall be carried out by an authorized service personnel only. The details of centralized help lines are attached.

4. For units installed beyond municipal limits of the jurisdiction of company's Authorized Service Center, it is responsibility of the purchaser to contact the nearest authorized service center and bring the unit to the authorized service center at its own cost and risk. All expenses incurred in collecting the units or parts thereof from the company's authorized service center, as well as expenses incurred with deputizing of service personnel/technicians towards conveyance and other incidentals etc. will be borne by the customer. Local Charges for transportation and handling charges may vary from location to location. Customers are advised to verify before. In case the customer desires to bring the unit on its own to the Authorized Service Centre, the same shall be at its own risks & consequences.

5. The concerned authorized service center will advise the customer whether to effect the repairs at site or at the authorized service center.

6. Call registered with the centralized helpline/Authorized service center, wherein only cleaning of the unit/parts in the unit due to dust accumulation on portions of the unit, general explanations/returning, are not to be considered as defects.

7. In case of repairs or replacement of any part/s of the unit, this warranty will thereafter continue and remain in force only for the unexpired period of the warranty. Replacement of parts would be purely at the discretion of LGEIL alone. In case the replacement of the entire unit is being made, (subject to the sole discretion of LGEIL), the same model shall be replaced and in the event such model has been discontinued, it shall be replaced with the model of price equivalent at the time of purchase.

8. In case of any damage to the product / customer abuse/ repairs by un-authorised personnel's/ misuse detected/ by the Authorized Service Center personnel, the warranty conditions are not applicable and repairs will be done subject to availability of parts and on a chargeable basis only.

9. This warranty shall not cover any consequential or resulting liability, damage or loss to property or life arising directly or indirectly out of any defect in the Washing Machine. The company's obligation under this warranty shall be limited to repair or providing replacement of defective parts only under the warranty period.

10. The company or its Authorized Service Center reserves the right to retain any part/s or component replaced at its discretion, in the event of a defect being noticed in the equipment during warranty period.

11. While the company will make every effort to carry out repairs at the earliest, it however is made expressly clear that the company is under no obligation to do so in a specified period of time.

12. Warranty does not cover accessories external to the equipment supplied by the dealer.

13. If any coloured internal or external components are replaced, there will be commitment to ensure that the shades match with the original or other components. The replaced shades, patterns, tints may vary from the customer's unit due to continuous usage of the unit. Any matching components changed at customer's request will be on chargeable basis except the component which actually needed

Warranty is not applicable in any of the following cases:

MODEL No. :

UNIT SERIAL No. :

CUSTOMER’S NAME & ADDRESS

TEL.

Customer’s Signature Dealer’s Signature

This Card is valid only if it is filled in and stamped by our authorised dealer on the date of purchase.

WARRANTY

CUSTOMER’S COPY

DATE OF PURCHASE :

DEALER’S NAME & ADDRESS

TEL.

LG Electronics

leaning and Maintenance

When there is a fear of freezing

• Close the water taps and remove the Water Supply Hose.

• Remove the water which remains in the water supply.

• Lower the drain hose and drain the water in the bowl and the drain hose by spinning.

If froze

• Remove the water supply hose, and immerse it in HOT water at approx.. 40 C.

• Pour approx.. 2 liters of HOT water at approx.. 40 C, into the bowl and let it stand for 10 minutes.

• Connect the water supply hose to the water tap and confirm that the washing machine performs the

supply and drainage of water.

Wash Inner-tub Leave the lid open after washing to allow moisture

Inlet Hoses Hoses connecting washer to faucet should be replaced every 5 years.

Exterior Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with

Long Vacations Be sure water supply is shut off at faucets. Drain all water from hoses if weather will

the inner-tub use a clean soft cloth dampened with liquid Detergent, then rinse. (Do not use harsh or gritty cleaners.)

sharp objects.

be below freezing.

Cleaning the Inside of your Washer

If you use fabric softener or do regular COLD water washing, it is very important that you occasionally clean the inside of your washer.

• Fill your washer with HOT water.

• Add about two cups of a powdered Detergent that contains phosphate.

• Let it operate for several minutes.

• Stop the washer, open the lid and leave it to soak overnight.

• After soaking, drain the washer and run it through a normal cycle.

Products that might damage your washing machine

• Concentrated bleaches and diaper sanitizer will cause damage to the paintwork and components of your washer.

• Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint

(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in washer or dryer.)

• Some pretreatment sprays or liquids can damage your washer’s control panel.

• Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine

but we suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in your washer.

• Do not use your washer lid as a work surface.

evaporate. If you want to clean

ommon washing problems

Many washing problems involve poor soil & stain removal, residues of lint and scum, and

fabric damage. For satisfactory washing results, follow these i nstructions.

WASH PROBLEM

Problems

Poor soil removal

Blue Stains

Black or gray marks on clothes

Yellow or brown rust stains

Lint

Residue or Detergent

Holes, tears, or snags

Possible Causes

• Not enough Detergent

• Wash Water Temperature

too low.

• Overloading the washer

• Incorrect wash cycle

• Incorrect sorting

• Do not pretreat stain

• Undiluted fabric softener

dispensed directly onto fabric

• A buildup caused by the

interaction of fabric softener and Detergent can flake off and mark clothes

• Not enough Detergent

• Iron or manganese in

water supply, water pipes, or water heater

• Incorrect sorting

• Tissues left in pocket

• Overloading the washer

• Undissolved Detergent

• Use too much Detergent

• Incorrect use of chlorine

bleach.

• Unfastened zippers,

hooks, buckles

• Ribs, tears and broken

threads

• Overloading the washer

• Degradation of fabric

Solutions & Preventive Measure

• Use correct amount of Detergent for load size, amount of

soil and water Hardness.

• Use WARM or HOT water for normal soil.

• Reduce load size.

• Wash with JEANS or SOAK wash cycle for heavy soiled

laundry.

• Separate heavily soiled items from lightly soiled ones.

• Pretreat stain and heavy soil according to directions shown

on page 9

• Rub the stain with bar soap. Wash.

• Do not overfill fabric softener dispenser and do not pour

liquid fabric softener directly onto fabric. See page 12 for more instructions.

• Keep the recommendations against Scrud(waxy buildup).

(refer to scrud page12.)

• Use correct amount of Detergent for load size, amount of soil

and water Hardness.

• To restore discolored load of whites, use rust remover safe

for fabric.

• Install nonprecipitating water softener or an iron filter in

your water supply system for an ongoing problem.

• Before washing, run water for a few minutes to clear lines.

• Wash lint givers eg towels, flannelette sheets, separately

from lint collectors eg synthetic fabrics and remove tissues in pockets before wash. See page 9 for sorting and caring before loading.

• Do not overload the washer

• Do not overload thewasher.

• SomeDetergents need to bepre-dissolved, check the Detergent

instructions. Try pre-dissolving theDetergent.

• Increase Wa ter Temperature usingHOT water safe for fabric.

• Use proper amount of Detergent.

• Never pour chlorine bleach directly on fabric.

See page 11 for adding liquid bleach.

• Fasten zippers, hooks, and buckles.

• Remove objects in pockets. See page 9 for caring before

• Do not overload the washer.

roubleshooting

Before calling for service, check the problem against the list bellows.

Symptom Error Message

Water Supply

Failure

Drainage Failure

Spin Failure

Door(Lid) Open

Internal sensing

failure

Power failure

Overflow failure

• Is the water tap shut off?

• Is the water supply cut off ?

• Is the tap or water supply hose frozen ?

• Is the water pressure low or is the filter of the inlet

valve clogged with impurities

• Is the Hot hose connected to cold?

• Is the Cold hose connected to hot?

• Is the drain hose positioned correctly?

• Is the drain hose bent or placed too high?

• Is the internal part of the hose or drain pump

(only pump model) clogged with impurities?

• Check if electric power has gone off.

• Is the laundry evenly balanced?

• Is the washing machine placed on a flat surface?

• Is the lid closed?

• Please call your nearest LG Electronics service center

for help.

Check up

Model

Size

Weight

Water tap pressure

a) WF-N7069NN / WF-N7069NP / WF-N7039NP b) T70CPD22N

a) 540(W)x540(D)x815(H) b) 540(W)x540(D)x835(H)

a) 31.5kg b) 32.5kg

30 - 800 kPa (0.3 - 8.0 kgf/cm )

Machine :_______________ Colour : ________________ Job No.:__________________

Dt. of pur.: _______________ M/C. S.No.:_______________

Name Of Customer : ___________________________________________ _____

Address: ________________________________________ _______________

__________________________________________ _______________

Tel:_____________(Resi)_____________(Mob). Email :_________________________

Tick Appropriate (by Service Engineer)

S.No. Check Point Yes/No

1 Physical condition of the Machine is satisfied?

Electrical condition of household wiring / earthing for

washing machine is proper? 3 Advised to turn off machine after use? 4

Explained Fixing of Inlet Hose Adapter to Tap?

Explained Leg Adjustment & Common Conditions 5

when Levelling Required?

Explained Cleaning of Lint Filter and Required 6

Cleaning Frequency?

Explained Cleaning of Inlet Valve Filter and 7

Required Cleaning Frequcny?

Explained Cleaning of Tub and Required Cleaning 8

Frequency?

Explained Regular Check Up and Safety Instructions ?

10 Anti Rat Cover installed?

Inlet Hose and Drain Hose checked for water

leakage after connection?

12 Leveling check & adjusted?

Explain Clothes Balancing, Proper Cloth Separation

for best Wash?

Explain all Features of the machine to customer?

15 Demo given to customer?

Explain Common Errors ( IE,OE,UE,dE,PE,AE,FE etc)

Explained unbalance error in Spin Mode?

Warranty terms explained?

Name of ASC :____________ Installation Dt : __________________ Installed by : _____________

Customer Remarks If Any :_________________________________________ ________________________________________________________________

I Here by certified by above Checks & Demo have been done to me with full of satisfaction and I am fully satisfied with the machine installation and performance of washing machine and I agree to take care of machine, suggestions (If Any) in respect of safety.

Signature Of Customer Date : Time:

For Best Use, Please Read the User’s Manual Properly.

Customer Copy

Installation Check sheet

Remarks

FATL

Machine :_______________ Colour : ________________ Job No.:__________________

Dt. of pur.: _______________ M/C. S.No.:_______________

Name Of Customer : ___________________________________________ _____

Address: ________________________________________ _______________

__________________________________________ _______________

Tel:_____________(Resi)_____________(Mob). Email :_________________________

Tick Appropriate (by Service Engineer)

S.No. Check Point Yes/No

1 Physical condition of the Machine is satisfied?

Electrical condition of household wiring / earthing for

washing machine is proper? 3 Advised to turn off machine after use? 4

Explained Fixing of Inlet Hose Adapter to Tap?

Explained Leg Adjustment & Common Conditions 5

when Levelling Required?

Explained Cleaning of Lint Filter and Required 6

Cleaning Frequency?

Explained Cleaning of Inlet Valve Filter and 7

Required Cleaning Frequcny?

Explained Cleaning of Tub and Required Cleaning 8

Frequency?

Explained Regular Check Up and Safety Instructions ?

10 Anti Rat Cover installed?

Inlet Hose and Drain Hose checked for water

leakage after connection?

12 Leveling check & adjusted?

Explain Clothes Balancing, Proper Cloth Separation

for best Wash?

Explain all Features of the machine to customer?

15 Demo given to customer?

Explain Common Errors ( IE,OE,UE,dE,PE,AE,FE etc)

Explained unbalance error in Spin Mode?

Warranty terms explained?

Name of ASC :____________ Installation Dt : __________________ Installed by : _____________

Customer Remarks If Any :_________________________________________ ________________________________________________________________

Signature Of Customer Date : Time:

For Best Use, Please Read the User’s Manual Properly.

Installation Check sheet

Company Copy

Remarks

FATL