LG T1532AFF6 User manual

T1532AFF6 T1732AFF6
MFL68019793 www.lg.com
Please read this manual carefully before operating your washing machine and retain it for future reference.
Product Features
START
WASHING
AUTO
POWER
OFF
SENSING
Laundry Sensor
Water Level Sensor
SETTING
Optimum W
ashing
Condition
If the lid is opened during wash, rinse and spin cycles, the machine will stop automatically.
Please close the door gently. Closing the door in an aggressive manner can cause damage and or injury.
Smart Drum achieved by DD Motor Technology
Smart Drum with Drum Washing Type is more hygienic and cleaner washer tub that
protects the fabric and prevents damages.
Normal logic control
A built-in load sensor automatically detects and measures the laundry load and a microprocessor optimizes washing conditions such as ideal water consumption and washing time.
Advanced technology is built into the Electronic Control System which ensures the best washing result.
New DD type washing with fabric care
Fast revolution accelerates
detergent dissolving and
soaks thoroughly into the
clothes.
Laundry blade
revolution to either
side in turn to remove
stains in the laundry.
Fast revolution of
tub creates the
current of water.
Tub rotates to either
side to balance and
unwind laundry.
Low Noise Direct Drive System
The advanced Brushless DC motor rotates the Tub directly without belt and clutch, thereby reducing the noise of the washer.
The washing machine adjusts to optimum speed according to the type of clothing in the load.
SmartDiagnosis
It is the technology to transmit the anomalies to the service center when
TM
there is a problem with the washer. It provides the service that gives faith and trust to the customers through precise and fast analysis.
Auto Restart
Auto Restart allows the program to restart all by itself in case of power fail­ure. lt does from the stage where it stopped.
2
Contents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your washer. You will find many answers to common problems in the Troubleshooting section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.
Introduction
Before Starting to Wash
Washing Programs
Additional Function Program
Installation
Care and Maintenance
Troubleshooting
Terms of Warranty Specification
Safety Information 4 Identification of Parts 7 Function Information 8 Preparation Before Washing 9 Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
10 Special Guide for Stain Removal 13 Function of each Button 14 Normal Wash 16 Smart Rinse 16 Eco Wash 16 Quick Wash 18 Delicates Wash 18 Towels Wash 18 Duvet Wash 18 Silent Wash 18 Favorite Wash 20 Soak Wash 21 Intensive Rinse 22 Tub Clean 23 Air Dry 24 Option Washing 25 Time Delay (RESERVATION) Wash 26 Other Useful Functions 27 Placing and Leveling 28 Connecting Water Supply Hose 29 Connecting Drain Hose 32 Grounding Method 33 Cleaning and Maintenance 34 Soft Safety Door 36 Common washing problems 37 Troubleshooting 38 SmartDiagnosis
TM
39 Terms of Warranty 40 Specification 41
3
Safety Information
Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.
This booklet is divided into 2 parts : Warning and Caution.
: This is a warning sign specifying user’s applications which might
be dangerous.
: This is a sign specifying ‘Strictly Forbidden’ applications.
WARNING
CAUTION
PROPER INSTALLATION
: Failure to comply with the instructions under this
sign may result in major physical injuries or death.
: Failure to comply with the instructions under this
sign may result in minor physical injuries or product damages.
CAUTION
• The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
• Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.
• Properly ground washer to conform with all governing codes and ordinances. Follow details in Installation Instructions.
If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.
• Must be positioned so that the plug is accessible.
If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.
• Make sure the plug is completely pushed into the outlet.
Failure to do so may cause electric shock and fire due to overheating.
• A precaution indicates that the washing machine shall not be installed at a humid place.
4
Safety Information
YOUR LAUNDRY AREA
WHEN USING THE WASHER
Warning
• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemical, etc.
Operating with such materials around the machine may trigger explosion or fire.
• Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.
There is potential danger that children might drown in the tub.
Do not touch the power plug with a wet hand.
It will cause electric shock
Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.
There is a rotating mechanism under the machine, so you could be injured.
Caution
• Use this appliance only for its intended purpose as described in this Owner’s Manual.
• The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.
• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
• A precaution indicates that the hands shall not be inserted into running water-extracting tub.
• A precaution on the washing machine whose lid can be opened during water extraction, that if it takes 15 s or more for complete stop of water-extracting chamber tub such a case should be understood as a trouble.
NOTE : Pressing Power button to turn off does NOT
disconnect the appliance from the power supply.
• Make sure that drainage is working properly.
If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.
• If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.
Call for repair. A machine that spins with its door open may cause injuries.
Never reach into washer while it is moving. Wait until the machine has completely stopped before opening the lid.
Even slow rotation can cause injury.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not use water hotter than 50°C.
Use of excessively hot water may cause damage to fabrics or cause leakage of water.
5
Safety Information
WHEN USING THE WASHER
WHEN NOT IN USE
WARNING
Do not use a plug socket and wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.
Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, dry-cleaning solvents, kerosene, etc). Do not add these substances to the wash water. Do not use or place these substances around your washer or dryer during operation.
It may ignite or explode.
CAUTION
• Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.
• When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.
• Wipe off dirt or dust on the contacts of the power plug.
Using unclean power plug may cause fire.
• Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.
Children may be trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.
Operating the machine with improperly replaced parts may be a cause for fire or electric shock.
Do not tamper with controls.
It may lead to electric shock, fire , break down, deformation.
Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.
Failure to observe these instructions may cause electric shock or fire due to short-circuit .
When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.
It will cause short circuit and electric shock.
6
Identification of Parts
DRAIN HOSE for non pump model
WATER SUPPLY HOSE Make sure the ater does not leak.
JET SPRAY CAP
FUNCTION SELECTOR
TUB
BASE
ADJUSTABLE LEGS Use to level the washing machine for correct balance & spin operation.
DRAIN HOSE for pump model Check if the drain hose is hung up before operating the washing machine.
DOOR SWITCH
POWER PLUG If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.
START/PAUSE BUTTON Use to start or stop the washing machine temporarily.
P
OWDER AND LIQUID
DETERGENT BOX
SOFT SAFETY DOOR
TEMPERED GLASS
BLEACH DISPENSER
Body
* Picture might be different by model.
Accessories
Water supply hoses
Drain hose
Anti-rat cover (option)
1 Each for COLD and
NOTE
” Part can be different according to the model.
or
HOT water
or
7
Function Information
Our machine provides various washing methods which suits various conditions and types of laundry.
Different types of laundry washing
Normal Wash
Use this Program for everyday washing e.g. sheets, towels, T-shirts.
Smart Rinse
Use this program to get better rising performance. (refer to page 16)
Eco Wash
To save water and detergent for less than 7kg of laundry that is not too dirty
Silent Wash
Use this program to wash quietly at night. (refer to page 18)
Duvet Wash
Use for blanket or duvet with (hand wash) sign.
(refer to page 18)
Towels Wash
Use this program to wash Towels, Shirts, Sheets, mixed loads.
Delicates Wash
Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 18) The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed. Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
• Before washing your woolens check the care label for the washing instructions.
• When washing woolens use a mild Detergent recommended for washing wool.
• Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
• To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight. (The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.) Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing mate­rial.) You may wish to handwash these articles and place them in the machine to spin dry.
Favorite Wash
This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 20)
Washing according to the condition of laundry
Quick Wash
Quick Wash can be selected to wash lightly soiled clothes of less than 3.0 kg in a short time. (refer to page 18)
Soak Wash
Soak Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 21)
Intensive Rinse
Use Intensive Rinse to remove detergents more effectively. (refer to page 22)
Other washing method
Tub Clean
Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 23)
Time Delay (RESERVATION) Wash
Time Delay (RESERVATION) Wash is used to delay the finishing time of the operation. The number of hours to be delayed can be set by the user accordingly. (refer to page 26)
Option Wash
When the user needs only Spin, Rinse/Spin, Rinse, Wash/Rinse, Wash, Wash/Rinse/Spin, Soak/Wash/Rinse/Spin (refer to page 25)
(refer to page 16)
. (refer to page 16)
(refer to page 18)
8
Preparation Before Washing
Care Labels
* Look for a care label on your clothes. This will tell you about the fabric content of your garment
and how it should be washed. Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
SOIL (Heavy, Normal, Light)
COLOR (Whites, Lights, Darks) Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors. Lint Producers Terry cloth, Chenille, Towels, Nappies, Diapers Lint Collectors Synthetics, Corduroy, Permanent Press, Socks
Check before Loading
Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches, pens, coins, and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
Pretreat any dirt and stains.
• Make sure the clothes are washable in water.
• Check the washing instructions.
• Remove tissue in pockets.
CAUTION
Do not wash or spin any item labeled or known to be water-proof or water-resistant, even if the product care label on the item permits machine washing. Failure to follow these instructions could result in severe damage to
your laundry, your washer and/or property damage as a result of abnormal vibration of the washer.
- Examples of water-proof or water-resistant items include certain mattress pads, mattress covers, rain gear, camping gear, skiing apparel , outdoor gear and similar items.
Pretreatment on stains or heavy soil
• Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
• Use a pretreat soil and stain remover. Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove. (For
Separate clothes according to the type and amount of soil.
more detail refer to page13)
Loading
Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).
Load Size
The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and sub­merge additional items. Close the lid and press Start button again to restart.
Light and Large-sized clothing
Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length, a net will prevent tangling during washing. snag on other clothes. Nylon net is not supplied by LG.
Fasten zippers, hook, and strings to make sure that these items don't
Never place items in the washer that are damp­ened with gasoline or other flammable fluids. No washer can completely remove oil. Do not dry anything that has ever had any type of oil on it (including cooking oils). Doing so can result in death, explosion, or fire.
WARNING
Fire Hazard
9
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
Using Water
Amount of WATER LEVEL
• This machine detects the quantity of laundry automatically, then sets the Water Level and proper amount of Detergent.
• When you select a wash program, the Water Level will be shown on the control panel.
• The following table shows the amount of water.
• When the Water Level is automatically detected, it may differ depending on the quantity of laundry even though the same Water Level is indicated on the control panel.
NOTE
[ Minimum water amount ]
It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub directly to some height. That’s because if water level reaches to the some height sensed by washer itself, washer automatically operates. In other words, it is needed to pour water to the point when washer starts operating.
Water Temperature
• The machine sets the appropriate temperature automatically according to the wash program .
• The temperature of the water impacts the effectiveness of all laundry additives and therefore, the cleaning results.
We recommend temperatures of:
- HOT 49~60°C…(120-140˚F) White items, diapers, underclothing and heavily soiled, colorfast items.
- WARM 29~40°C…(85-105˚F) Most items
- COLD* 18~24°C…(65-75˚F) Only very bright colors with light soil.
• When washing in COLD water additional steps may be needed:
- Adjust Detergent amount and pre-dissolve Detergent in WARM water
- Pretreat spots and stains
- Soak heavily soiled items
- Use appropriate bleach
* Temperature below 18°C…(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29°C…(80-85˚F). If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.
NOTE
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.
Using Dispenser Drawer
Using the Dispenser Drawer
The dispenser drawer contains 2 compartments:
• Liquid Fabric Softener
• Liquid or Powder Low-Sudsing, High-Efficiency Detergent
The dispenser automatically dispenses additives at the proper time in the wash cycle.
1. Slowly open the dispenser drawer by pulling the drawer out until it stops.
2. After adding laundry products, slowly close the dispenser drawer. Closing the draw-
er too quickly could result in early dispensing of additives.
• Avoid overfilling or splashing when adding laundry products to the dispenser. Doing
so could result in early dispensing of laundry products.
At the end of the cycle, you may see water in the compartments. This is part of the nor­mal operation of the washer.
NOTE : Do not use bleach in the dispenser drawer.
10
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems. Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
We recommend the use of domestic Detergent, (powder, liquid or concentrated). Soap flakes or granulated soap powders should not be used in your washing machine. When washing woolens remember to use Detergent suitable for washing woolens.
How much Detergent
The correct amount of Detergent will vary depending on the amount of soil in your clothes (Jeans and work clothes may need more Detergent, while bath towels usually need less.). For liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about half­way through the wash. There should be a thin layer of foam over the surface of the water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough Detergent has been used; soil and lint can settle back on the clothes or the washing machine. If excess Detergent is used, the rinse will not be as clean and efficient. Also, it could cause environ­mental pollution, so use it accordingly.
Adding Detergent
Add measured detergent to the detergent compartment of the dispenser drawer.
Detergent is flushed through the dispenser at the beginning of the wash phase. Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load.
Avoid using too much detergent in your washer, as it can lead to oversudsing and detergent residue being left on the clothes.
Note : Using Liquid detergent
- Dilute Liquid detergent with water and pour into the tub, start the cycle.
- Delay wash course is not available if you use liquid detergent.
Attention
Using liquid detergent without diluting, or leaving laundry for a long time after pouring diluted liquid detergent into the tub might cause damage, bleaching or discoloration of cloth.
11
Use of Water, Dispenser Drawer, Detergent, Bleach and Softener
Bleach dispenser
Using Liquid Bleach
• Check clothing care label for special instructions and separate the laundry to be bleached
• Dilute liquid chlorine bleach.
• Measure the recommended amount of liquid bleach carefully following instructions on the bottle.
• Before starting the washer, pour measured amount of bleach directly into bleach dispenser. Avoid splashing or overfilling. Powdered bleach should be mixed with water before pouring.
NOTE
Never pour undiluted liquid bleach directly onto clothes or into the wash basket.
This may cause change of color or damage the laundry.
Do not pour powdered bleach into bleach dispenser.
Using Fabric Softener
If desired, pour the recommended amount of liquid fabric softener into the right-hand compartment.
Use only liquid fabric softener. Dilute with water to the maximum fill line.
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing of the fabric softener, which could stain clothes.
NOTE : Do not pour fabric softener directly on the wash load. It may stain the clothes.
Attention
Do not mix with Detergent or bleach.
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric softener dispenser.
Scrud(Waxy Build up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it can result in stains on your clothes or an unpleasant smell in your washer.
If you wish to use fabric softener we recommend
• Using fabric softener sparingly.
• When filling the dispenser, do not splash or overfill.
• Clean dispenser as soon as the cycle is finished.
• Clean your machine regularly. (refer to page 23 or 34)
• Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or HOT wash e.g. every 5th wash should be at least a warm one.
• Fabric softener of thinner consistency is less likely to leave residue on the dispenser and contribute to a build-up.
12
Special Guide for Stain Removal
WARNING
Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
• Read and comply with all instructions on stain removal products.
• Keep stain removal products in their original labeled containers and out of children’s reach.
• Thoroughly wash any utensil used. Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
• Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or
other flammable or explosive substances because they give off vapors that could ignite or explode.
• Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
• Remove stains promptly.
• Determine the kind of stain, then follow the recommended treatment in the stain removal chart below.
• To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.
• Use COLD water on unknown stains because HOT water can set stains.
• Check care label instructions for treatments to avoid on specific fabrics.
• Check for colorfastness by testing stain remover on an inside seam.
• Rinse and wash items after stain removal.
Stain Removal
STAIN
Adhesive tape, chewing gum, rub­ber cement
Baby formula, dairy products, egg Beverages (coffee, tea, soda, juice,
alcoholic beverages) Blood
Candle wax, crayon
Chocolate Collar or cuff soil, cosmetics Dye transfer on white fabric Grass
Grease, oil, tar (butter, fats, salad dressing, cooking oils, car grease, motor oils)
Ink
Mildew, scorch
Mud Mustard, tomato Nail polish
Paint, varnish
Rust, brown or yellow discoloration
Shoe polish
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains. Pretreat stain. Wash using COLD water and bleach safe for fabric.
Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using bleach safe for fabric.
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Pretreat with prewash stain remover or rub with bar soap. Use packaged color remover. Wash using bleach safe for fabric. Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric. Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes. Pretreat with prewash stain remover. Wash using bleach safe for fabric. May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics. WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing. For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration. LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric.
Pretreat with prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach safe for fabric.
TREATMENT
Follow fabric care
label instructions
13
Function of each Button
Display laundry
progress
Water wave button
Hot and cold wash laundry button
Water Level button
(display detergent amount)
Display remaining time, reservation time,
and alarm for trouble
• Laundry progress is indicated here.
• Process to be done will have light on. Process in progress will blink and process already done will have light off.
• To control water wave.
• Initially set at “medium” but will not be indicated. For strong or delicate wash, press Strong Wave or Delicate Wave. (all course except Delicates, Silent and Tub Clean can adjust wave.)
Time Delay
(Reservation) button
• Use for laundry reservation.
• To cancel, turn power off.
(refer to page 26)
To select hot water, cold water, or hot and cold water.
Can be changed during operation.
If hot wash is selected, laundry will be done with hot water and rinse will
be done with cold water.
Only cold water will be used at Delicates course.
(It might damage laundry if Hot water is used)
Hot
and cold water makes appropriate temperature by mixing hot water and
cold water adequately when Hot water and cold water is selected.
Hot wash, cold wash is automatically selected under Smart Rinse and
Tub Clean course.
Use to adjust Water Level.
It can be changed during
operation.
Add detergent as much as indicated amount next to Water Level.
Detergent is based on condensed detergent.
• During operation this indicates time to finish of laundry. ex) indicates remaining time of laundry, rinse, spin dry during operation/pause.
• If there is a trouble, it blinks with buzzer sound and indicates the source of trouble. It will work normally after troubleshooting.
NOTE
* For optimizing the washing algorithm, the displaying time may be changed during washing-increased by
8minutes at maximum and decreased by 4 minutes at maximum.
* The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to
the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.
14
Wash, Rinse, Spin button Child lock function Program button
Air dry
START/PAUSE button
SmartDiagnosis
TM
Function Display
Power button
To change laundry time, number of rinse, strength of spin dry.
Use safe rinse to more effectively remove detergent.
Press START/PAUSE button to indicate remaining time.
Use to prevent an accident by children operating the machine.
Press ‘rinse’ button and ‘spin’ button simultaneously for 3 seconds to select or deselect. (refer to page 27)
To select laundry
course.
Select course by type of clothes and level of dirtiness.
• To shorten dry time.
• Air dry is a stand alone process.
Press for 3 seconds to select, press power button to deselect.
(refer to page 24)
• Use to start or pause the washing process.
• After 4 minutes in pause status, it will automatically turn off.
• It marks the place to put the phone to receive signal when a problem occurs.
(refer to page 39)
• Use to turn the power on or off.
• Push again and power goes on or off.
• The power goes off automatically about 10 seconds after the wash is finished.
* The control panel may differ according to different models.
15
Washing Programs
1
2
3
1
2
3
4
1
2
3
4
Washing
Programs
Used for normal loads, this mode automatically selects the most appropriate conditions and completes the sequence in one operation. The built-in sensor detects the size of the load and the ideal wash power and wash, rinse and spin times are set accordingly.
Use this program to increase rinsing performance. This would include underwear and baby clothes. If
someone has sensitive skin or skin
trouble,use this program.
Add the
laundry
• Select the Smart Rinse program on the
Control panel.
Add
the Detergent
Water will be supplied. After supplying, laundering will be started.
Add designated amount of detergent by Water Level and close the door. Use exclusive neutral detergent or dry detergent for home
.
Eco course consumes less water and electricity to wash normal clothes.
16
Select the program on the Control panel.
Eco Wash
• Add the appropriate quantity of Detergent as indicated by the Water Level. Or follow the Detergent manufacturer's instructions.
Close the lid Finish Caution & Note
5
4
6
6
5
7
6
5
7
• If water is already in the tub, or putting wet laundry into the tub before starting will increase the Water Level.
• With lightweight bulky loads, Water Level can be set low.
• Water will be supplied. After supplying,
aundering will
l be started.
• Tub will rotate more than nce without water (While
o
ater Level LED blinking) to
W recognize Water Level.
• Then the Water Level and the
amount of Detergent to be used will be shown and water will be supplied.
• When the wash program ends, the
uzzer will ring for
b 10 seconds before the Power goes off automatically.
• Changes to Water Temperature (Hot Wash/Cold Wash) and wash level are possible during operation.
(refer to page 10)
• It will cold water and hot water will be supplied adequately to
adjust water temperature automati cally.If Cold Wash is only selected it will laundry only with cold water.
17
Washing Programs
1
2
4
1
2
3
3
4
1
2
3
4
1
4
3
2
1
2
3
4
Washing
Programs
Use this mode when washing lightly soiled clothes for a short time. The highly recommended laundry amount is under 3.0kg.
Use this program for washing deli­cate fabrics such as lingerie and woolens. (wash only “water washable” clothes) Before washing your woolens check the care label for the washing instructions. (wash only water washable clothes)
To separate towel with other clothes.
Add the laundry
Select the
Quick Wash
program on the Control panel.
• Select the
Delicates
program on the Control panel.
Select the Towels program on the Control panel.
Add
the Detergent
• Add the appropriate quantity of Detergent as indicated by the Water Level. Or follow the Detergent manufacturer’s instructions.
• Use neutral Detergent appropriate for the laundry.
• When washing woolens use a mild Detergent recommend-ed for washing wool.
• Add the appropriate quantity of Detergent As indicated by the Water Level Or follow the Detergent Manufacturer's instructions.
.
Use for blanket or bedclothes with
hand wash』sign.
Use this program to wash quietly in Silent especially during late night and dawn.
18
• Select the Duvet
program on the Control panel.
Select the Silent program on the Control panel.
• Pour detergent after dis­solve at warm water. If detergent is pour into cold water, it might cause leftover detergent in bedclothes.
• Add the appropriate quantity
of Detergent as indicated by the Water Level. Or follow the Detergent manufacturer's instructions.
Close the lid Finish Caution & Note
6
5
7 6
5
7
6
5
7
6
5
7
6
5
7
Below this line
Lay out in cool floor or on a hanger covered by a towel to dry these type of clothes.
It might have damped clothes because spin dry intensity and time are set to short to prevent damage of clothes. (Spin dry cannot be changed)
• Use this program to wash Towels, Shirts, Sheets,mixed loads.
• Cashmere bedclothes, acrylic blanket, mixed spinning blanket, woolen blanket, infilling (polyester 100), and bed sheet might be damaged by floating. Please purchase a separate laundry net to wash.
• Separate bed clothes to general clothes. It might cause laundry to askew and results in abnormal washing.
• Spin dry might take longer to spread out laundry if bedclothes are lumped to a side.
• Never laundry an electric blanket and a carpet. It cause damage to a laundry machine and the laundry.
• Please use laundry net to soak and sink bedclothes that are easy to be inflated. It might cause damage on laundry and machine parts if inflated.
• Regardless of its size, we recommend to wash one by one. If two bedclothes with different material are washed at a time, it might cause abnormal spin dry due to imbalance.
• How to put blankets into a laundry tub. It into 'N' or 'M' shape, and put it below upper side plastic parts of a laundry tub.
Silent program takes longer washing time than Normal program.
To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has more moisture than normal.
19
1
2
3
4
Favorite Wash
Press the POWER button to turn power on.
Put laundry in and Press the Program button to Select Favorite Program.
Press Water Wave button and select Water Wave. ("Medium Wave" if nothing is selected)
Press Hot Wash, Cold Wash laundry to select water temperature.
Select Water Level by pressing Water Level button.
Select laundry time, number of rinse, and Spin intensity desire to save by
pressing each of laundry, rinse and Spin button.
Press the START/PAUSE button.
Add designated amount of detergent by Water Level and close the door.
Please use appropriate exclusive neutral detergent or dry detergent for home when
"Delicates" course is selected for Favorite Program.
When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.
20
To save Favorite Program.
1. Select laundry options and operate as above.
2. It is saved as the operation starts.
3. It is saved even if laundry is paused or power is turned off.
To recall your
1. Press POWER on.
2. Select the Favorite cycle by pressing the Program.
3. Press the START/PAUSE button. Then the wash cycle starts.
Favorite
cycle.
1
2
3
4
5
6
Soak Wash
Press the POWER button to turn power on.
Put laundry in and Press the Program button to Select Washing Program.
Delicates, Quick Wash, Tub Clean Program do not suppose soak laundry.
Press soak laundry button.
“Soak laundry” can be selected by pressing button and indicated by light on soak indicator( )
Soak selection : 15 30 45 1:00 2:00 3:00 off 15
Press each of rinse and Spin button to select number of Rinse and Spin.
Add designated amount of detergent by Water Level and close the door.
Press the START/PAUSE button.
Water will be supplied. After supplying, laundry will be started.
When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.
21
1
2
3
4
5
6
times times times times times times times times
times
timestimes
Intensive Rinse
Press the POWER button to turn power on.
Put laundry in and Press the Program button to Select Washing Program.
Intensive Rinse can only be selected only under Normal, Smart Rinse, and Favorite.
Press Rinse button to start Intensive Rinse( ).
Press each of Wash button and Spin button to set duration.
Add designated amount of detergent by Water Level and close the door.
Press the START/PAUSE button.
When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.
NOTE
• Use Intensive Rinse to remove detergents more effectively.
• Intensive Rinse might work if Water Level changed during operation.
22
Tub Clean
If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer. Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub.
Press the POWER button to turn power on.
Press the Program button to Select Tub Clean Program.
Press the START/PAUSE button.
Time will be displayed on screen.
After put in exclusive detergent for laundry tub or oxide bleaching agent in the bleaching agent input and close the door.
When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.
Recommended cleaner :
(1) Powder bleaching agent :
Purchase a product at a market and refer to usage instruction at the back of the product
(2) Liquid bleaching agent:
Dilute to 300 times of water capacity of washing machine.
Do not put laundry for laundry tub course.
Use oxide bleaching agent (300g). (do not use chlorine bleaching agent.)
Clean laundry tub per month using laundry tub course.
Please clean laundry tub if there are fuzz.
It is convenient to use laundry tub course at night or during an outing
Automatic detection of time to clean Tub
After Power On button pressing, if is blinking in the display, it is the time for Tub Cleaning.
If you want to skip the Tub Clean, press option buttons to select desired cycle.
After performing tub clean, will disappear until next cleaning time.
Tub Clean time is detected automatically as per the usages of washer (Generally once after 30 usages)
23
Air Dry
Press the POWER button to turn power on.
Press Spin for 3 seconds to select Air Dry.
Other function cannot be selected during Air Dry.
Automatically set to 60 minutes upon selection.
Press Spin button again to select duration (90min
To deselect Air Dry press power button.
.
120 min
.
Press the START/PAUSE button.
When the wash program ends, the buzzer will ring for 10 seconds before the Power goes off automatically.
60 min.)
24
When you select Air Dry for more than 60 minutes
1) You can reduce the drying time by minimizing the moisture in the laundry.
2) Always keep the laundry amount to 2kg or less and make sure to spread it out evenly.
3) Select 60 minutes for cotton laundry and 120 minutes for synthetic fiber laundry for effective Moisture removal.
Option Washing
When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.
1
Press the POWER button to turn power on.
2
3
4
Only Wash
Press the select the desired timing.
Only Wash,Rinse
Press the select the desired timing.
Press the select the desired times of rinse.
You can use this option for preventing wrinkles of laundry
Press the Water Level button, to control the water
level according to the amount of laundry. If you do not choose anything, it is set the middle water level automatically.
Add the laundry into the washing tub.
Wash
Wash
Rinse
button to
button to
button to
Only Rinse
Press the select the desired times of rinse.
Press the select the desired times of rinse.
Press the select the desired times of spin.
Rinse
Only Rinse,Spin
Rinse
Spin
button to
button to
button to
Only Spin
Press the select the desired times of spin.
When you want to only drain, wait until the water in the washing tub drains completely.
Spin
button to
Only Drain
5
Press the START/PAUSE button.
6
Add the detergent and close the lid.
NOTE
• When a Wash, Wash/Rinse or Rinse only option is selected, after the wash is completed the water will not be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained completely. Then press the START/PAUSE button.
• If you do not specify the water level, then Medium will be automatically selected.
• If only Rinse is selected, the process will start from Water Supply.
25
Loading...
+ 57 hidden pages