Page 1
LCD TV
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : ML-024D
MODEL : RZ-20LA70
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
Oct.,2003
Printed in KoreaP/NO : 3828VD0168C
Page 2
- 2 -
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ..................................................................................3
DESCRIPTION OF CONTROLS .............................................................. 4
ADJUSTMENT INSTRUCTION .................................................................7
TROUBLE SHOOTING............................................................................13
PRINTED CIRCUIT BOARD....................................................................14
BLOCK DIAGRAM...................................................................................17
EXPLODED VIEW .................................................................................. 18
EXPLODED VIEW PARTS LIST..............................................................19
REPLACEMENT PARTS LIST ............................................................... 20
SVC. Sheet .................................................................................................
Page 3
- 3 -
PRODUCT SAFETY
IMPORTANT SAFETY NOTICE
This manual was prepared for use only by properly trained audiovisual service
technicians. When servicing this product, under no circumstances should the
original design be modified or altered without permission from LG Electronics
Inc. All components should be replaced only with types identical to those in the
original circuit and their physical location, wiring, and lead dress must conform
to original layout upon completion of repairs. If any fuse (or Fusible Resistor) in
this TV receiver is blown, replace it only with the factory specified fuse type and
rating. When replacing a high wattage resistor (Oxide Metal Film Resistor, over
1W), keep the resistor 10mm away from PCB. Always keep wires away from
high voltage or high temperature parts.
Special components are also used to prevent shock and fire hazard.
These components are indicated by the letter “x” included in their component
designators and are required to maintain safe performance. No deviations are
allowed without prior approval by LG Electronics Inc. Service work should be
performed only after you are thoroughly familiar with these safety checks and
servicing guidelines.
Circuit diagrams may occasionally differ from the actual circuit used.
This way, implementation of the latest safety and performance improvement
changes into the set is not delayed until the new service literature is printed.
CAUTION: Do not attempt to modify this product in any way.
Never perform customized installations without manufacturer’s
approval.
Unauthorized modifications will not only void the warranty, but may
lead to property damage or user injury.
GENERAL GUIDANCE
An isolation Transformer should always be used during the servicing
of a receiver whose chassis is not isolated from the AC power line. Use a
transformer of adequate power rating to protect against personal injury from
electrical shocks. It will also protect the receiver and its components from being
damaged by accidental shorts of the circuitry that may be inadvertently
introduced during the service operation.
Before returning the receiver to the customer, always perform an AC leakage
current check on the exposed metallic parts of the cabinet, such as antennas,
terminals, etc., to be sure the set is safe to operate
without damage of electrical shock.
LEAKAGE CURRENT COLD CHECK
(ANTENNA COLD CHECK)
With the instrument’s AC plug removed from AC source, connect an electrical
jumper across the two AC plug prongs. Place the AC switch in the on position,
connect one lead of ohm-meter to the AC plug prongs tied together, and touch
other ohm-meter lead in turn to each exposed metallic parts such as antenna
terminals, phone jacks, etc. If the exposed metallic part has a return path to the
chassis, the measured resistance should be between 1MΩ and 5.2MΩ. When
the exposed metal has no return path to the chassis the reading must be
infinite. Any other abnormality that exists must be corrected before
the receiver is returned to the customer.
ELECTROSTATICALLY SENSITIVE DEVICES
Some semiconductor (solid-state) devices can be damaged easily by static
electricity. Such components commonly are called Electrostatically Sensitive
(ES) Devices. Examples of typical ES devices are integrated circuits and some
field-effect transistors and semiconductor “chip” components. The following
techniques should be used to help reduce the incidence of component damage
caused by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic charge on the
body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be
removed for potential shock reasons prior to applying power to the unit under
test.
2. After removing an electrical assembly equipped with ES devices, place the
assembly on a conductive surface such as an ESD mat, to prevent
electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices
not classified as “anti-static” can generate electrical charges sufficient to
damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charge
sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until
immediately before you are ready to install it. (Most replacement ES devices
are packaged with leads electrically shorted together by conductive foam,
aluminum foil, or comparable conductive material.)
7. Immediately before removing the protective material from the leads of a
replacement ES device, touch the protective material to the chassis or circuit
assembly into which the device will be installed.
Caution: Be sure no power is applied to the chassis or circuit, and observe
all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES
devices. (Otherwise, seemingly harmless motion, such as the brushing
together of your clothing or the lifting of your foot from a carpeted floor, can
generate static electricity sufficient to damage an ES device.)
Page 4
DESCRIPTION OF CONTROLS
- 4 -
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the side
panel of the set.
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
1. MUTE
switches the sound on or off.
2. TV/AV
selects TV or AV monitor mode.
clears the menu from the screen.
switches the set on from standby.
3. LIST
displays the programme table.
4. Q.VIEW
returns to the previously viewed programme.
selects a favourite programme.
5.
D / E
(Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the current mode.
6. NUMBER BUTTONS
switches the set on from standby or directly select a number.
7. SSM (Sound Status Memory)
recalls your preferred sound setting.
8. SLEEP
sets the sleep timer.
POWERMUTE
TV/AV I/II
LIST
PR
PR
VOL
OK
123
456
789
SSM PSM
0
VOL
Q.VIEW MENU
SLEEP TEXT
UPDATE
TIME
SIZE MIX
HOLD
REVEAL
INDEX MODE
?
i
M
1
9
10
11
12
13
2
3
4
5
6
7
8
Page 5
- 5 -
9. POWER
switches the set on from standby or off to standby.
10. I/II
selects the language during dual language broadcast.
selects the sound output (option).
11. MENU
selects a me
12. PSM (Picture Status Memory)
recalls your preferred picture setting.
13. TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
*
: No function
COLOURED BUTTONS : These buttons are used for teletext (only
TELETEXT models) or programme edit.
POWERMUTE
TV/AV I/II
LIST
PR
PR
VOL
OK
1 2 3
4 5 6
7 8 9
SSM PSM
0
VOL
Q.VIEW MENU
SLEEP TEXT
UPDATE
TIME
SIZE MIX
HOLD
REVEAL
INDEX MODE
?
i
M
1
9
10
11
12
13
2
3
4
5
6
7
8
Page 6
- 6 -
1. ON/OFF (O/I)
switches the set on from standby or off to
standby.
Note : Power line lives even when the power
is off.
2. TV/AV
selects TV or AV monitor mode.
clears the menu from the screen.
switches the set on from standby.
3. MENU
selects a menu.
4. OK
accepts your selection or displays the current
mode.
5. FF / GG (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
6.
DD / EE
(Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
7. POWER/STANDBY INDICATOR (O)
illuminates red in standby mode.
illuminates green when the set is switched on.
8. REMOTE CONTROL SENSOR
9. HEADPHONE SOCKET
Connect the headphone plug to this socket.
10. AUDIO/VIDEO IN SOCKETS (AV2)
Connect the audio/video out sockets of external equipment to these sockets.
S-VIDEO/AUDIO IN SOCKETS (SAV)
Connect the video out socket of an S-VIDEO
VCR to the S-VIDEO socket.
Connects the audio out sockets of the SVIDEO VCR to the audio sockets as in AV2.
Back panel
Side panel
RL
VIDEO
AV2
AUDIO
(MONO)
H/P
S-VIDEO
TV/AVMENUOKVOLPR
/I
ON/OFF
7
8
9 10
6
5
4
3
2
1
• RZ- 20LA70 series
Page 7
- 7 -
1. Application Object
This instruction is for the application to the LCD TV.
2. Notes
(1) This set uses an adapter, so connect the adapter and the
set correctly before adjustment.
(2) The adjustment must be performed under the correct
sequence.
(3) The adjustment must be performed in the circumstance of
25
!5cC of temperature and 65!10% of relative humidity if
there is no specific designation.
(4) The set must be operated for 15 minutes preliminarily
before adjustment if there is no specific designation.
[ ‘Heat Run’ must be performed with the full white signal or TV
noise signal in the internal part of the set.
[ The time for ‘Heat Run’ can be changed owing to production
plan.
[ Line Test condition (TV): standard color signal 65!1dBuV
ADJUSTMENT INSTRUCTION
Page 8
- 8 -
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
SCART
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
SCART
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
4. Option 1 data setting (200PR ~ A2 ST:1bit, SYS:2bit composition)
Page 9
- 9 -
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
SCART
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
SCART
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
Page 10
- 10 -
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
SCART
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
01
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
0
1
2
3
SCART
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
Page 11
- 11 -
OPTION
Data
200PR
TEXT
I/II SV
TOP
A2 ST SYS
248
249
250
251
252
253
254
255
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
1
2
3
0
1
2
3
SCART
1
1
1
1
1
1
1
1
5. Option2 data(ACMS~BBACK:1bit,LANG:3bit)
OPTION
Data
ACMS
VOL
BBACK LANG
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
OPTION
Data
ACMS
VOL
BBACK LANG
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
Page 12
- 12 -
6. Option3 data(IIC AFT~CH+AU:1bit)
OPTION
Data
HiDEV
TSS
IIC T MONO CH+AUS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Page 13
- 13 -
1 No sound Defective Reset IC of IC604. 1) Check volume and speaker.
- Speaker Defective MSP3410G of IC601. - Sound comes out only when being inputted into Audio
- Earphone Defective B+(8V) of IC604. L/R.
2) Check after replacing IC603.
3) Replace IC601.
4) Check and replace B+ of IC604.
2 Video color beat noise Earphone shield case being touched.
Check the mould of shield and SJ209, Replace shield case.
Soldering IC501. 1) Check signal of Video input.
2) Check signal of R.G.B output.
3) Re-soldering
1 No screen Input error of inverter connector 1) Bend the pin legs of
P802B
connector -> recheck them
2) Check and repair IC805 SI4925.
P1 and Pin 50 connector 1) Check and fix P1 connector
being slipped out
Cracked components and 1)Check and repair tuner board and main board
soldering at tuner board 2)Solder Q403
2 Dark screen 1) Defective LCD lamp 1) Replace the inverter
2) Defective inverter 2) Replace the LCD lamp
3) Input error of inverter connector 3) Check the connector input.
TROUBLE SHOOTING
1. General Features
No. Symptom Cause Check Point
Check Point
2. TV and external input
No. Symptom Cause
Page 14
- 14 -
PRINTED CIRCUIT BOARD
MAIN(TOP)
Page 15
- 15 -
MAIN(BOTTOM)
Page 16
- 16 -
POWER
CONTROL
Page 17
BLOCK DIAGRAM
- 17 -
Page 18
- 18 -
EXPLODED VIEW
400
310
120
560
530
250
340
360
380
370
330
350
210
300
112
520
230
430
Page 19
- 19 -
112 6306V20002A LCD MODULE,V201V1-T01 VGA CHIMEI TFT COLOR
120 6400GKTX01A SPEAKER,FULLRANGE F1527C-6428 K-TONE 8OHM 7/12W 83DB OTHERS
210 4811V00076A BRACKET ASSEMBLY,REAR AV RZ-20LA70 ML024D .
230 4950V00192A METAL,SHIELD SBHG ML024
4950V00192C METAL,SHIELD SBHG 20LA70 C/SKD
250 4950V00188A METAL,FRAME SBHG FOR CMO MODULE
4950V00188B METAL,FRAME SBHG C/SKD
300 3091V00587A CABINET ASSEMBLY,RZ-20LA70 NON NON ML024D SET,LGEIS
3091V00587C CABINET ASSEMBLY,RZ-20LA70 STEREO ML024D C/SKD
310 5020V00871A BUTTON,CONTROL RZ-20LA70 ABS 8KEY .
330 4950V00157E METAL,HINGE ASSY NON 20LA70
340 4810V00767A BRACKET,STAND 20LA60 ML012B NON HINGE FRONT
350 4810V00768A BRACKET,STAND 20LA60 ML012B NON HINGE COVER
360 4810V00924A BRACKET,STAND RZ-20LA70 NON ABS .
370 4950V00193A METAL,STAND SPCC(CR) BASE(20LA70)
380 4950V00194A METAL,STAND SPCC(CR) SUPPORTER(LA70)
400 3809V00407A BACK COVER ASSEMBLY,RZ-20LA70 NON (STUH),LGEIS
3809V00407C BACK COVER ASSEMBLY,RZ-20LA70 1SCART 3850VC0002F(LGERU)
3809V00407D BACK COVER ASSEMBLY,RZ-20LA70 1SCART C/SKD
430 3550V00383A COVER,REAR AV RZ-20LA70 HIPS 60HR .
520 6871VMMR05A PWB(PCB) ASSEMBLY,MAIN ML-024D RZ-20LA70
530 6871VSMQ31A PWB(PCB) ASSEMBLY,SUB CONT ML024D 70TOOL CONTROL ASSY
560 6871VSMQ30A PWB(PCB) ASSEMBLY,SUB POWER ML024D 70TOOL POWER ASSY
EXPLODED VIEW PARTS LIST
No.
PART NO.
DESCRIPTION
Page 20
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
Q404
Q405
Q406
Q407
Q501
Q502
Q510
Q551
Q602
Q603
Q701
Q703
Q706
Q801
Q802
R1211
R1212
D100
D1101
D1102
D1103
D1104
D1105
D1106
D701
D702
D704
D706
D707
D710
D711
ZD1101
ZD1102
ZD202
ZD203
ZD400
ZD701
ZD704
C10
C101
C1101
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR387500AA
0TR322709AA
0TR387500AA
0TR150400BA
0TF492509AA
0TF492509AA
0DD181009AB
0DD181009AB
0DD181009AB
0DD181009AB
0DD181009AB
0DD181009AB
0DD181009AB
0DRSA00150A
0DD100009AM
0DD100009AM
0DR060009AA
0DRSD00091A
0DR340009AA
0DR340009AA
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZRM00178A
0DZ330009BA
0DZ910009AJ
0DZ110009AD
0CE227DF618
0CE107BF618
0CC15003G06
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
KTC3227-Y,TP(KTC1627A),KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
SI4925DY TP TEMIC 30V 6.1A SO-8
SI4925DY TP TEMIC 30V 6.1A SO-8
KDS181 TP KEC - 85V - - - 300MA
KDS181 TP KEC - 85V - - - 300MA
KDS181 TP KEC - 85V - - - 300MA
KDS181 TP KEC - 85V - - - 300MA
KDS181 TP KEC - 85V - - - 300MA
KDS181 TP KEC - 85V - - - 300MA
KDS181 TP KEC - 85V - - - 300MA
RBV-406 BK USC 600V 4A 80VA .SEC
EU1ZV(1) TP SANKEN
EU1ZV(1) TP SANKEN
TVR06J TP DO41 600V 0.6A - - SF20JC10 ST FTO220(4115) 100V 20A
MBRS340 TP - 40V 3A 80A - 2MA
MBRS340 TP - 40V 3A 80A - 2MA
UDZS TE-17 5.1B 0.2W 5.1V 5MA -PF
UDZS TE-17 5.1B 0.2W 5.1V 5MA -PF
UDZS TE-17 5.1B 0.2W 5.1V 5MA -PF
UDZS TE-17 5.1B 0.2W 5.1V 5MA -PF
ZENER HZT33 TAPING
MTZJ9.1B TP DO34 0.5W 9.1V 5UA MTZJ11B TP DO34 - 11V 5UA -
220UF STD 16V M FL TP5
100UF KME 16V M FL TP5
15PF D 3KV 10%,-10% SL FMTW
LOCA. NO PART NO DESCRIPTION
IC100
IC101
IC102
IC1101
IC1110
IC1111
IC1112
IC1121
IC1122
IC351
IC352
IC501
IC502
IC601
IC603
IC604
IC650
IC701
IC702
PC1
PC2
Q101
Q102
IC1102
IC1103
IC1104
IC1105
IC1223
IC1224
IC2
Q1
Q100
Q1101
Q1101
Q1102
Q1103
Q1200
Q200
Q202
Q353
Q402
Q403
0ISM555000B
0IAL241610B
0IFA752700A
0IMCRO2001A
0IMCRRH005A
0IMCRRH005A
0IMCRRH005A
0IMCRMZ001A
0IMCRMZ001A
0IMCRFA010A
0ISO204000A
0IMCRTW001B
0ICTMMO005A
0IMCRMN011D
0IKE704200J
0IMCRFA009A
0IMCRTI022D
0IPMGSK012A
0IMCRFA007A
0ILI817000G
0ILI817000G
0IFA270000A
0IFA270000A
0TFFC80044A
0TFFC80044A
0TFFC80044A
0TFFC80044A
0TF492509AA
0TF492509AA
0TF492509AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
SDA555XFL 52DIP ST FLASH MEMORY
AT24C16A-10PI-2.7 8PIN DIP ST EEPROM
KA75270Z 3 TP RE-SET IC MC-007
OZ960S O2MICRO 20P SSOP R/TP
UM6K1N ROHM 6P SOT363 R/TP 30V 0.1A
UM6K1N ROHM 6P SOT363 R/TP 30V 0.1A
UM6K1N ROHM 6P SOT363 R/TP 30V 0.1A
MP1583DN 8P TSOP R/TP DC-DC
MP1583DN 8P TSOP R/TP DC-DC
KA7809R, FAIRCHILD 2P D-PAK, R/TP
CXA2040AQ 32P,QFP BK IIC BUS VIDEO
LG8801-H TECHWELL 160P QPFD TRAY
SC786109DWR2 MOTOROLA SOIC 16P
MSP3410G QA B8 V3 MICRONAS 80P QFP
KIA7042AF SOT-89 TP 4.2V VOLTAGE
KA78M08RTM, FAIRCHILD 2P D-PAK
TPA3004D2 48P PQFP TRAY 9WSTEREO
STR-W6853P SANKEN 6P T0-220 ST
KA431Z FAIRCHILD 3DIP,TO-92 TP
LTV817M-VB 4P,DIP BK PHOTO COUPLER
LTV817M-VB 4P,DIP BK PHOTO COUPLER
2N7000TA TO-92, 3P TP LEVEL SHIFT
2N7000TA TO-92, 3P TP LEVEL SHIFT
FDS8958A FAIRCHILD R/TP SO-8 30V 7A
FDS8958A FAIRCHILD R/TP SO-8 30V 7A
FDS8958A FAIRCHILD R/TP SO-8 30V 7A
FDS8958A FAIRCHILD R/TP SO-8 30V 7A
SI4925DY TP TEMIC 30V 6.1A SO-8
SI4925DY TP TEMIC 30V 6.1A SO-8
SI4925DY TP TEMIC 30V 6.1A SO-8
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
IC
TRANSISTOR
- 20 -
DIODE
CAPACITOR
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
Page 21
- 21 -
LOCA. NO PART NO DESCRIPTION
C1102
C1103
C1104
C1105
C1106
C1107
C1127
C1128
C113
C1140
C1141
C1142
C1143
C1144
C1145
C1146
C1147
C1150
C1151
C1200
C1201
C1202
C1207
C1208
C1209
C1210
C1211
C1222
C1223
C1226
C1227
C1228
C1229
C1230
C1231
C1234
C1235
C200
C201
C209
C211
C212
C215
C216
C219
C220
C289
C331
0CC15003G06
0CC15003G06
0CC15003G06
0CC15003G06
0CC15003G06
0CE4772J618
0CK105DF64A
0CK105DF64A
0CE107BF618
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CK225DFK4A
0CE227BH618
0CE227BH618
0CE227DH618
0CN475FH67A
0CN475FH67A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CN475FH67A
0CN475FH67A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CK105DF64A
0CN475FH67A
0CK105DF64A
0CK105DF64A
0CE107DD618
0CK105DF64A
0CK105DF64A
0CE476DF618
0CE106DF618
0CE227DD618
0CE106DF618
0CE106DF618
0CE226DF618
0CE226DF618
0CE104DK618
0CE107DF618
15PF D 3KV 10%,-10% SL FMTW
15PF D 3KV 10%,-10% SL FMTW
15PF D 3KV 10%,-10% SL FMTW
15PF D 3KV 10%,-10% SL FMTW
15PF D 3KV 10%,-10% SL FMTW
470UF KMF 35V 20% TP 5 FL
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
100UF KME 16V M FL TP5
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
2.2UF 2012 16V 20%,-20% F(Y5V) R/TP
220UF KME 25V M FL TP5
220UF KME 25V M FL TP5
220UF STD 25V M FL TP5
4.7UF 3225 25V 20% R/TP X5R
4.7UF 3225 25V 20% R/TP X5R
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
4.7UF 3225 25V 20% R/TP X5R
4.7UF 3225 25V 20% R/TP X5R
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
4.7UF 3225 25V 20% R/TP X5R
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
100UF STD 10V M FL TP5
1UF 2012 16V 20% R/TP F(Y5V)
1UF 2012 16V 20% R/TP F(Y5V)
47UF STD 16V M FL TP5
10UF STD 16V M FL TP5
220UF STD 10V M FL TP5
10UF STD 16V M FL TP5
10UF STD 16V M FL TP5
22UF STD 16V M FL TP5
22UF STD 16V M FL TP5
0.1000UF STD 50V M FL TP5
100UF STD 16V M FL TP5
LOCA. NO PART NO DESCRIPTION
C351
C353
C354
C356
C357
C362
C364
C380
C381
C383
C403
C404
C408
C410
C412
C413
C499
C501
C523
C526
C541
C581
C613
C614
C616
C617
C617
C620
C621
C624
C625
C629
C633
C643
C700
C701
C703
C704
C706
C707
C708
C709
C710
C717
C718
C719
C720
C725
0CE227DF618
0CE475DK618
0CE476DF618
0CE106DF618
0CE106DF618
0CE107DF618
0CE336DF618
0CE105DK618
0CE106DF618
0CE106DF618
0CE476DH618
0CE108DD618
0CE106DK618
0CE227DF618
0CE105DK618
0CK224DF56A
0CE476DK618
0CE107DF618
0CE104DK618
0CE107DF618
0CE107DF618
0CE107DF618
0CE106DF618
0CE106DF618
0CE107DF618
0CE107BH618
0CE107BF618
0CE335DK618
0CE107BF618
0CK224DF56A
0CK224DF56A
0CE107DF618
0CE107DF618
0CE476BF618
181-091D
0CF474285B0
181-120P
181-120P
0CE226DK618
0CE1072V610
181-091D
181-120K
181-120K
181-091D
181-091D
0CE227DJ618
181-091D
0CE4772J618
220UF STD 16V M FL TP5
4.7UF STD 50V 20% FL TP 5
47UF STD 16V M FL TP5
10UF STD 16V M FL TP5
10UF STD 16V M FL TP5
100UF STD 16V M FL TP5
33UF STD 16V M FL TP5
1UF STD 50V M FL TP5
10UF STD 16V M FL TP5
10UF STD 16V M FL TP5
47UF STD 25V 20% FL TP 5
1000UF STD 10V M FL TP5
10UF STD 50V M FL TP5
220UF STD 16V M FL TP5
1UF STD 50V M FL TP5
220000PF 2012 16V 10% R/TP X7R
47UF STD 50V M FL TP5
100UF STD 16V M FL TP5
0.1000UF STD 50V M FL TP5
100UF STD 16V M FL TP5
100UF STD 16V M FL TP5
100UF STD 16V M FL TP5
10UF STD 16V M FL TP5
10UF STD 16V M FL TP5
100UF STD 16V M FL TP5
100UF KME 25V M FL TP5
100UF KME 16V M FL TP5
3.3UF STD 50V 20% FL TP 5
100UF KME 16V M FL TP5
220000PF 2012 16V 10% R/TP X7R
220000PF 2012 16V 10% R/TP X7R
100UF STD 16V M FL TP5
100UF STD 16V M FL TP5
47UF KME TYPE 16V 20% FL TP 5
DEHR33A102KN2A 1000PF 1KV 10%,-10%
0.47UF S 275V 10% PCX2 337 BULK
470 PF 4KV K JE R FL 10
470 PF 4KV K JE R FL 10
22UF STD 50V M FL TP5
100UF KMF 450V 20% FL BULK
DEHR33A102KN2A 1000PF 1KV 10%,-10%
2200PF 4KV M E FMTW LEAD 4.5
2200PF 4KV M E FMTW LEAD 4.5
DEHR33A102KN2A 1000PF 1KV 10%,-10%
DEHR33A102KN2A 1000PF 1KV 10%,-10%
220UF STD 35V M FL TP5
DEHR33A102KN2A 1000PF 1KV 10%,-10%
470UF KMF 35V 20% TP 5 FL
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
Page 22
- 22 -
LOCA. NO PART NO DESCRIPTION
C726
C727
C728
C730
C731
C733
C734
C743
C744
C745
C746
C747
C777
C832
L1201
L1202
L1203
L1204
L174
L175
L176
L177
L401
L705
L706
T1101
T1102
T1103
T1104
T1105
T1106
T701
P1
P100
P101
P1101
P1102
P601
P602
FR704
L502
L503
0CK10101515
0CE226DK618
0CE476BK618
0CE4772J618
0CE227DJ618
181-120K
0CE4772J618
0CE477DD618
0CE227DK618
0CE477DD618
0CE477DD618
0CE477DD618
181-091D
0CE107DF618
6140VR0005B
6140VR0005B
6140VR0005B
6140VR0005B
0LC0233002A
0LC0233002A
0LC0233002A
0LC0233002A
0LA0272K139
6140VR0008B
6140VR0008B
6170VH0002A
6170VH0002A
6170VH0002A
6170VH0002A
6170VH0002A
6170VH0002A
6170VMCA65A
6602T10002D
366-932E
6602V20005L
6631V20014E
387-A07B
366-932B
366-932C
0RP0020J809
0RRZVTA001A
0RRZVTA001A
100PF D 1KV 10% B(Y5P) TR
22UF STD 50V M FL TP5
47UF KME 50V M FL TP5
470UF KMF 35V 20% TP 5 FL
220UF STD 35V M FL TP5
2200PF 4KV M E FMTW LEAD 4.5
470UF KMF 35V 20% TP 5 FL
470UF STD 10V M FL TP5
220UF STD 50V M FL TP5
470UF STD 10V M FL TP5
470UF STD 10V M FL TP5
470UF STD 10V M FL TP5
DEHR33A102KN2A 1000PF 1KV 10%,-10%
100UF STD 16V M FL TP5
COIL,ENERGY SLF7045T-330MR82
COIL,ENERGY SLF7045T-330MR82
COIL,ENERGY SLF7045T-330MR82
COIL,ENERGY SLF7045T-330MR82
INDUCTOR,CHIP 3.3UH CERATECH R/TP
INDUCTOR,CHIP 3.3UH CERATECH R/TP
INDUCTOR,CHIP 3.3UH CERATECH R/TP
INDUCTOR,CHIP 3.3UH CERATECH R/TP
INDUCTOR,AXIAL LEAD 27UH K 4X10.5 TP
COIL,ENERGY SLF12575T-150M3R2 15UH
COIL,ENERGY SLF12575T-150M3R2 15UH
TRANSFORMER,UI-11.7 860000UH 1-CH
TRANSFORMER,UI-11.7 860000UH 1-CH
TRANSFORMER,UI-11.7 860000UH 1-CH
TRANSFORMER,UI-11.7 860000UH 1-CH
TRANSFORMER,UI-11.7 860000UH 1-CH
TRANSFORMER,UI-11.7 860000UH 1-CH
TRANSFORMER,SMPS[COIL] EER3019
ETC 50P FH12-50S-0.5H HIROSE .
2.5MM 6P GIL-G LG CABLE S (STICK)
2.0MM 12P GIL-S LG CABLE STRAIGHT
12P 2.0MM 300MM (LGC)GIL-S (LGC)GIL-T
7P 2.5MM 150MM GIL-G GIL-J NON
2.5MM 3P GIL-G LG CABLE S (STICK)
2.5MM 4P GIL-G LG CABLE S (STICK)
0.02 OHM 1 W 20% TA52
MNR-14-E0A-J-101 R OHM 100 OHM 5%
MNR-14-E0A-J-101 R OHM 100 OHM 5%
LOCA. NO PART NO DESCRIPTION
L504
L505
L506
L507
L518
R702
R703
R704
R705
R706
R706
R711
R712
R714
R715
R727
R736
SW1101
SW1102
SW1103
SW1104
SW1105
SW1106
SW1107
SW1108
L101
L1101
L1101
L119
L1200
L1205
L1206
L200
L200
L201
L201
L202
L202
L204
L205
L206
L207
L208
L209
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RRZVTA001A
0RKZVTA001C
0RKZVTA001K
0RS5602K619
0RS5602K619
0RS5602K619
0RS1203K607
0RS5602K619
0RS5602K619
0RS5602K619
180-A01E
0RD0472H609
0RD0472H609
140-313A
140-313A
140-313A
140-313A
140-313A
140-313A
140-313A
140-313A
6210TCE001G
6210TCE001A
6210TCE001G
6210TCE001A
6210TCE001G
6210TCE001G
6210TCE001G
6200JB8010L
6210TCE001A
6210TCE001A
6200JB8010L
6210TCE001A
6200JB8010L
6210TCE001A
6210TCE001A
6210TCE001G
6200JB8010L
6210TCE001A
6210TCE001A
MNR-14-E0A-J-101 R OHM 100 OHM 5%
MNR-14-E0A-J-101 R OHM 100 OHM 5%
MNR-14-E0A-J-101 R OHM 100 OHM 5%
MNR-14-E0A-J-101 R OHM 100 OHM 5%
MNR-14-E0A-J-101 R OHM 100 OHM 5%
8.2M OHM 1/2 W 5% TA52 UL
0.47M OHM 1/2 W 5% TA52
56K OHM 2 W 5.00% TR
56K OHM 2 W 5.00% TR
56K OHM 2 W 5.00% TR
120K OHM 2 W 5.00% TA62
56K OHM 2 W 5.00% TR
56K OHM 2 W 5.00% TR
56K OHM 2 W 5.00% TR
2 W RW ROUND G 2W 0.33J TA31(63)
47 OHM 1/2 W 5.00% TA52
47 OHM 1/2 W 5.00% TA52
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
TACT 2LEAD 100G(TA) NON 5V 0.001A
HH-1M3216-501 3216MM R/TP
HB-1S2012-080JT 2012MM CHIP-BEAD
HH-1M3216-501 3216MM R/TP
HB-1S2012-080JT 2012MM CHIP-BEAD
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
MLB-201209-1000L-N2
HB-1S2012-080JT 2012MM CHIP-BEAD
HB-1S2012-080JT 2012MM CHIP-BEAD
MLB-201209-1000L-N2
HB-1S2012-080JT 2012MM CHIP-BEAD
MLB-201209-1000L-N2
HB-1S2012-080JT 2012MM CHIP-BEAD
HB-1S2012-080JT 2012MM CHIP-BEAD
HH-1M3216-501 3216MM R/TP
MLB-201209-1000L-N2
HB-1S2012-080JT 2012MM CHIP-BEAD
HB-1S2012-080JT 2012MM CHIP-BEAD
FILTER & CRYSTAL
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible
SWITCH
COIL & INDUCTOR
CONNECTOR
RESISTOR
Page 23
- 23 -
LOCA. NO PART NO DESCRIPTION
L351
L400
L402
L501
L515
L516
L517
L580
L581
L601
L602
L603
L701
L702
L703
L704
L801
L802
L803
L99
LF701
R1108
R1109
R1110
R1111
R1112
R226
R228
R229
R230
R505
R710
Z100
Z500
Z600
A1
A1
A1
A1
A1
A1
A1
A1
A1
A2
A3
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210VC0004A
6210TCE001G
6210TCE001A
6210TCE001A
6210TCE001G
6210TCE001G
6210TCE001G
125-022K
125-022K
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6210TCE001G
6200JB8012Q
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6200JB8010L
6210TCE001A
125-022K
156-A01L
156-A02X
156-A02M
3828VA0448B
3828VA0448C
3828VA0448D
3828VA0448F
3828VA0448G
3828VA0448H
3828VA0448J
3828VA0448K
3828VA0448R
6710V00091G
6410VPH001A
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
BK3216 4S600 3.2X1.6X0.8MM R/TP
HH-1M3216-501 3216MM R/TP
HB-1S2012-080JT 2012MM CHIP-BEAD
HB-1S2012-080JT 2012MM CHIP-BEAD
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
FERRITE 1UH TAPING
FERRITE 1UH TAPING
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
HH-1M3216-501 3216MM R/TP
OR 14*7*7.5H SMC BK 6.0-11.0MH
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
MLB-201209-1000L-N2
HB-1S2012-080JT 2012MM CHIP-BEAD
FERRITE 1UH TAPING
RESONATOR,CRYSTAL HC49U 6.000MHZ
RESONATOR,CRYSTAL HC49U 27.000MHZ
RESONATOR,CRYSTAL 18.432MHZ 30PPM
MANUAL,OWNERS ML024D LGEBN
MANUAL,OWNERS ML024D LGEHS
MANUAL,OWNERS ML024D LGEUK
MANUAL,OWNERS ML024D LGEIS
MANUAL,OWNERS ML024D LGEES
MANUAL,OWNERS ML024D STUH
MANUAL,OWNERS ML024D LGEFS
MANUAL,OWNERS ML024D LGESW
MANUAL,OWNERS ML024D LGERU
REMOTE CONTROLLER,ML012B FULL .
POWER CORD,SP023+IS034 (LGERU)
LOCA. NO PART NO DESCRIPTION
A3
A3
A3
A3
F701
LED1
P701
PA1101
RJ201
SC204
TH701
TU401
VA701
6410VEH008A
6410VEH008C
6410VEH008D
6410VBH005A
131-098B
0DL200000CA
6620VZ0002A
6726VV0006D
6613V00008F
381-091B
163-048D
6700PF0002A
164-003K
POWER CORD,SP022+ISO34 (LGEBN)
POWER CORD,SP023+ISO34 (STUH)
POWER CORD,SP28+IS-034 (LGEIS)
POWER CORD,SP60+IS034 (LGEUK)
FUSE,SLOW BLOW 4000MA 250 V 5.2X20
LED SAM5670(DL-2LRG) BK Y-GREEN SOCKET (CIRC),DRAWING IS7007
REMOTE CONTROLLER RECEIVER ,38.0KHZ
JACK ASSY,PMJ014F E/P(ST)+S-VHS+3P H6.5
JACK,SCART S-091B UGCOM SCART 21
THERMISTOR,KL15L2R5 +/- 15% 125V
TUNER,TAFH-S321D LG PAL FS 4SYS
VARISTOR,SVC621D-14A ILJIN 620V 0%
ACCESSORIES
MISCELLANEOUS
Page 24
P/NO:3854VA0135A-S1
2003.10.13
Page 25
SVC. SHEET : 3854VA0135A-S1
Page 26
LCD TV
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : ML-041B
MODEL : RZ-20LA70(RZ-20LA70 Rev A)
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
*( ) ID LABEL Model No.
*Same looking with new chassis
*Issue Date; 2004. 06
Page 27
CONTENTS
CONTENTS .............................................................................................. 2
PRODUCT SAFETY ..................................................................................3
SPECIFICATION........................................................................................4
ADJUSTMENT INSTRUCTION ...............................................................10
TROUBLE SHOOTING............................................................................12
BLOCK DIAGRAM...................................................................................17
WIRING DIAGRAM..................................................................................19
EXPLODED VIEW .................................................................................. 20
EXPLODED VIEW PARTS LIST..............................................................21
REPLACEMENT PARTS LIST ............................................................... 22
SVC. SHEET ...............................................................................................
Page 28
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC
power line. Use a transformer of adequate power rating as this
protects the technician from accidents resulting in personal injury
from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this TV receiver is blown,
replace it with the specified.
When replacing a high wattage resistor (Oxide Metal Film Resistor,
over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
X-RAY Radiation
Warning:
To determine the presence of high voltage, use an accurate high
impedance HV meter.
Adjust brightness, color, contrast controls to minimum.
Measure the high voltage.
The meter reading should indicate
23.5
1.5KV: 14-19 inch, 26
1.5KV: 19-21 inch,
29.0
1.5KV: 25-29 inch, 30.0 1.5KV: 32 inch
If the meter indication is out of tolerance, immediate service and
correction is required to prevent the possibility of premature
component failure.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas, terminals, etc., to
be sure the set is safe to operate without damage of electrical
shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
switch in the on position, connect one lead of ohm-meter to the AC
plug prongs tied together and touch other ohm-meter lead in turn to
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC voltage
measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
The source of X-RAY RADIATION in this TV receiver is the High
Voltage Section and the LCD PANEL.
For continued X-RAY RADIATION protection, the replacement
panel must be the same type panel as specified in the
Replacement Parts List.
IMPORTANT SAFETY NOTICE
0.15uF
To Instrument's
exposed
METALLIC PARTS
AC Volt-meter
1.5 Kohm/10W
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
Page 29
CAUTION: Before servicing receivers covered by this service
manual and its supplements and addenda, read and follow the
SAFETY PRECAUTIONS on page 3 of this publication.
NOTE: If unforeseen circumstances create conflict between the
following servicing precautions and any of the safety precautions on
page 3 of this publication, always follow the safety precautions.
Remember: Safety First.
General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.
2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by "drawing an arc".
3. Do not spray chemicals on or near this receiver or any of its
assemblies.
4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.
5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.
6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.
8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid-state) devices can be damaged easily
by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES
devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques
should be used to help reduce the incidence of component
damage caused by static by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as "anti-static" can generate
electrical charges sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it.
(Most replacement ES devices are packaged with leads
electrically shorted together by conductive foam, aluminum foil
or comparable conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be
installed.
CAUTION: Be sure no power is applied to the chassis or circuit,
and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Otherwise harmless motion such as
the brushing together of your clothes fabric or the lifting of your
foot from a carpeted floor can generate static electricity
sufficient to damage an ES device.)
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron and appropriate
tip size and shape that will maintain tip temperature within the
range or 500
F to 600 F.
2. Use an appropriate gauge of RMA resin-core solder composed
of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean and well tinned.
4. Thoroughly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle.
Do not use freon-propelled spray-on cleaners.
5. Use the following unsoldering technique
a. Allow the soldering iron tip to reach normal temperature.
(500
F to 600 F)
b. Heat the component lead until the solder melts.
c. Quickly draw the melted solder with an anti-static, suction-
type solder removal device or with solder braid.
CAUTION: Work quickly to avoid overheating the
circuitboard printed foil.
6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
(500
F to 600 F)
b. First, hold the soldering iron tip and solder the strand against
the component lead until the solder melts.
c. Quickly move the soldering iron tip to the junction of the
component lead and the printed circuit foil, and hold it there
only until the solder flows onto and around both the
component lead and the foil.
CAUTION: Work quickly to avoid overheating the circuit
board printed foil.
d. Closely inspect the solder area and remove any excess or
splashed solder with a small wire-bristle brush.
SERVICING PRECAUTIONS
Page 30
IC Remove/Replacement
Some chassis circuit boards have slotted holes (oblong) through
which the IC leads are inserted and then bent flat against the
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique
as outlined in paragraphs 5 and 6 above.
Removal
1. Desolder and straighten each IC lead in one operation by gently
prying up on the lead with the soldering iron tip as the solder
melts.
2. Draw away the melted solder with an anti-static suction-type
solder removal device (or with solder braid) before removing the
IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and
solder it.
3. Clean the soldered areas with a small wire-bristle brush.
(It is not necessary to reapply acrylic coating to the areas).
"Small-Signal" Discrete Transistor
Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as
possible to the component body.
2. Bend into a "U" shape the end of each of three leads remaining
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding
leads extending from the circuit board and crimp the "U" with
long nose pliers to insure metal to metal contact then solder
each connection.
Power Output, Transistor Device
Removal/Replacement
1. Heat and remove all solder from around the transistor leads.
2. Remove the heat sink mounting screw (if so equipped).
3. Carefully remove the transistor from the heat sink of the circuit
board.
4. Insert new transistor in the circuit board.
5. Solder each transistor lead, and clip off excess lead.
6. Replace heat sink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Fuse and Conventional Resistor
Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.
CAUTION: Maintain original spacing between the replaced
component and adjacent components and the circuit board to
prevent excessive component temperatures.
Circuit Board Foil Repair
Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
following guidelines and procedures should be followed whenever
this condition is encountered.
At IC Connections
To repair a defective copper pattern at IC connections use the
following procedure to install a jumper wire on the copper pattern
side of the circuit board. (Use this technique only on IC
connections).
1. Carefully remove the damaged copper pattern with a sharp
knife. (Remove only as much copper as absolutely necessary).
2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
carefully crimp it around the IC pin. Solder the IC connection.
4. Route the jumper wire along the path of the out-away copper
pattern and let it overlap the previously scraped end of the good
copper pattern. Solder the overlapped area and clip off any
excess jumper wire.
At Other Connections
Use the following technique to repair the defective copper pattern
at connections other than IC Pins. This technique involves the
installation of a jumper wire on the component side of the circuit
board.
1. Remove the defective copper pattern with a sharp knife.
Remove at least 1/4 inch of copper, to ensure that a hazardous
condition will not exist if the jumper wire opens.
2. Trace along the copper pattern from both sides of the pattern
break and locate the nearest component that is directly
connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead of the
nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Carefully crimp and solder the connections.
CAUTION: Be sure the insulated jumper wire is dressed so the
it does not touch components or sharp edges.
Page 31
1. Application range
This specification is applied to ML-041B chassis.
2. Requirement for Test
Testing for standard of each part must be followed in below
condition.
(1) Temperature: 25°C ± 2°C
(2) Humidity: 65% ± 10%
(3) Power: Standard input voltage (AC 100-240V, 50/60Hz)
(4) Measurement must be performed after heat-run more than
30min.
(5) Adjusting standard for this chassis is followed a special
standard.
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement
.
3.General Specification
1
2
3
Maker
Type
ActiveDisplay Area
Pixel Pitch [mm]
Electrical Interface
Color Depth
Size [mm]
Surface Treatment
Operating Mode
Back light Unit
R/T Typ.
Maker
Type
ActiveDisplay Area
Pixel Pitch [mm]
Electrical Interface
Color Depth
Size [mm]
Surface Treatment
Operating Mode
Back light Unit
R/T Typ.
Maker
Type
ActiveDisplay Area
Pixel Pitch [mm]
Electrical Interface
Color Depth
Size [mm]
Surface Treatment
Operating Mode
Back light Unit
R/T Typ.
LPL
TFT Color LCD Module
20.1 inches(380.16mm) diagonal(Aspect 4:3)
0.6375mm(H)x0.6375mm(V)xRGB
TTL
8BIT, 16,777,216 colors
450(H)x 348.7(V)x20(D)
Glare, Hard Coating(3H)
Normally Black
6 CCFL(6 lamps)
16ms(R.T.:7/10ms + F.T.:18/20ms)
AUO
TFT Color LCD Module
20.1 inches(510.00mm) diagonal
0. 6376mm(H)x0.6375mm(V)xRGB
TTL
8-BIT 16,777.216 Colors
434(H)x331.6(V)x29.6(D)
Hard Coating, AR,Glare (3H)
Normally Black
6 CCFL(6 lamps)
16ms
CMO
TFT Color LCD Module
20.1 inches(510.00mm) diagonal
0. 6375mm(H)x0.6375mm(V)xRGB
TTL
8-BIT 16,777.216 Colors
448(H)x339.6(V)x25(D)
Anti Glare, Hard Coating(3H)
Normally Black
6 CCFL(6 lamps)
16ms(R.T.:5/7ms + F.T.:11/14ms)
Item Specification Remark
No.
LPL
AUO
CMO
Page 32
4. Feature and Function
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Teletext
REMOCON
CVBS VIDEO Input
S-VIDEO Input
Component input
PERI TV Connector
H/p input
RS-232
Discrete IR
2 Carrier Stereo
NICAM Stereo
2 Carrier Dual
NICAM Dual
DW(Double Window) Mode
MW(Multi Window) Mode
Film Mode
Noise Reduction
Progressive Scan
Motion Detection
SRS WOW
wivel Speaker
Ez-pip
ARC
DRP
DCDI
HDCP
TOP, FLOF
NEC Code
1
1
1
Full SCART : 1
1
NO
YES
BG, DK
BG, I, LL'
BG, DK
BG, I, LL'
X
X
X
X
X
X
X
X
X
X
X
X
X
Item Specification Remark
No.
Top(option)
PAL/ NTSC
Rear
Rear
Rear (option, NT)
Rear (option,EU)
Rear
5.Optical Character
Item RemarkSpecification
Viewing Angle
<CR
10>
Luminance
Contrast Ratio
CIE Color Coordinates
Typical
MAX/MIN
ALL white/All black
R/L,
U/D
Luminance(cd/
)
Variation
LPL
85/85
85/85
400
1.3
400
0.289
0.335
0.692
0.335
0.289
0.583
0.143
0.909
WHITE
RED
Green
Blue
W
X
W
Y
W
r
Y
r
X
g
Y
g
Xb
Yb
Typ.
Typ.
Typ.
Typ.
Typ.
Typ.
Typ.
Typ.
CMO
80/80
75/65
450
1.3
500
0.285
0.293
0.692
0.332
0.276
0.601
0.142
0.075
CMO
85/85
90/90
450
1.3
600
0.31
0.33
0.64
0.34
0.29
0.61
0.14
0.07
No.
1
2
3
4
Page 33
6.Engineering Specification
1
2
3
4
5
Power Supply
Normal
Stand By
Suspend Mode
DPM Off Mode
Cut-off Switch off
ITEM
D-SUB Pin Configuraion
Control Function
Comoponent Jack
D2 Jack
(525i, 525p)
H/V Sync
On/On
Off/On
On/Off
Off/Off
-
Spectification
1: RED
3: Blue:
5: S.T(GND)
7: Green GND
9: N.C
11: ID0(GND)
13: H-Sync
15: SCL
1) Contrast/Brightness
2) H-Position/V-Position
3) Tracking : Clock/ Phase
4) Auto Configure
RESET
1: Y
3: Pb
5: Pr
1: Y GND
2: Pb
5: Pr
7: LINE1 Ready
9: Line2
11: Line3
13: Line3 ready
2: Green
4: ID2(GND)
6: RED GND
8: Blue GND
10: D-GND
12: SDA
14: V-Sync
Shell: GND
2: Y GND
4: Pb GND
6: Pr GND
8: LINE1
10: Line2 Ready
12: SWITCH GND
14: SWITCH
Remark
10: Digital GND
Middle east/
NTSC Area
JAPAN Only
Video
Active
Off
-
Power Consumption
65W
1W
1W
1W
0W
PBP SWAP
ON/OFF
Item Specification Remark
No.
LED Color
GREEN
LED
OFF
Page 34
6-2.Power
NO
1
2
3
4
5
6
7
8
9
10
11
AC Power Shut Down Voltage
DC Voltage, Inverter
DC Voltage, LCD Panel
DC Voltage, Audio
DC Voltage, Tuner(5)
DC Voltage, Tuner(9)
DC Voltage, Tuning(31)
DC Voltage, VCTi(5)
DC Voltage, VCTi(8)
DC Voltage, VCTi(3.3)
DC Voltage, VCTi(1.8)
DC Voltage, GM2221 (3.3)
DC Voltage, GM2221 (1.8)
DC Voltage, Digital (3.3)
DC Voltage, Digital (5)
90
22.8
11.4
14.0
4.5
8.5
31
4.5
7.5
3.1
1.6
3.1
1.6
2.8
4.5
24
12
15
5
9
33
5
8
3.3
1.8
3.3
1.8
3.3
5
264
25.2
12.6
16.0
5.5
9.5
35
5.5
8.5
3.5
2.0
3.5
2.0
3.8
5.5
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
Japan only
Item Min Typ Max Unit Remark
6-3. External Interface
NO
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
Video Input Level
Audio Input Level
Audio Input Frequency Response
Audio Input S/N
Audio Input Distortion
Audio Input Dynamic Range
Video Output Level
Video Output Frequency Response
Video Output S/N
Audio Output Level
Audio Output Frequency Response
Audio Output S/N
Audio Output Distortion
Video Input Level, R/G/B
Video Input Level, Component(Y, PB, PR)
RGB Input Resolution, Vertical
RGB Input Resolution, Horizontal
RGB Input Horizontal Frequency
RGB Input Frame Rate
0.85
0.4
0.1
40
2
0.85
3.8
40
0.4
0.1
40
0.6
0.6
1
0.5
1
0.5
0.7
0.7
768
1280
1.15
0.6
7
2
1.15
0.6
7
2
0.8
0.8
Vpp
V
KHz
DB
%
V
Vpp
MHz
DB
V
KHz
DB
%
Vpp
Vpp
Pixel
Pixel
KHz
Hz
EN-50049
NTSC:0.4Vrms(Typ)
75 ohm
75 ohm
Only 20" 640 Pixel
480
See table 5-5
See table 5-5
Item Min Typ Max Unit Remark
6-4. The Others
NO
1
2
3
4
5
6
Search Sensitivity
Soft Ware Functionality Test
REMOCON Working Sensitivity, Straight
REMOCON Working Sensitivity, T/B/L/R
Closed Caption Sensitivity
Teletext Sensitivity
0.1
0.1
-85
10
9
-70
-70
dBm
m
m
dBm
dBm
LGE Specification
30 degree
NTSC ONLY
Item Min Typ Max Unit Remark
Page 35
1. Application Object
This instruction is for the application to the LCD TV.
2. Adjustment
2.1 Adjustment overview
The unit is set to automatically adjust using the
factory automation equipment. However when errors
occur, it should be adjusted manually.
2.2 Auto Gain/Offset adjustment
2.2.1 RF Mode adjustment
2.2.1.1 Adjustment preparation
Conduct Heat Run at the RF fog signals for more than
30 minutes.
2.2.1.2 Auto Gain/Offset adjustment
Press IN-START Key to convert to the adjustment
mode using the adjustment (SVC) remote controller,
and press VOL+ Key at the Auto Gain menu.
Once the adjustment is completed, press the Enter
Key to save and finish the adjustment.
ADJUSTMENT INSTRUCTION
Page 36
SVC REMOCON
1 POWER
2 POWER ON
3 MUTE
4 P-CHECK
5 S-CHECK
6 ARC
7 CAPTION
8 TXT
9 TV/AV
10 TURBO SOUND
11 TURBO PICTURE
12 IN-START
13 ADJ
14 MPX
15 EXIT
16 APC(PSM)
17 ASC(SSM)
18 MULTIMIDIA
19 FRONT-AV
20 CH
21 VOL
22 ENTER
23 PIP CH-(OP1)
24 PIP CH+(OP2)
25 PIP SWAP(OP3)
26 PIP INPUT(OP4)
27 EYE
28 MENU
29 IN-STOP
30 STILL
31 TIME
32 SIZE
33 MULTI PIP
34 POSITION
35 MODE
36 PIP
37 TILT
38 0~9
To turn the TV on or off
To turn the TV on automatically if the power is supplied to the TV. (Use the
POWER key to deactivate): It should be deactivated when delivered.
To activate the mute function.
To check TV screen image easily.
To check TV screen sound easily
To select size of the main screen (Normal, Spectacle, Wide or Zoom)
Switch to closed caption broadcasting
To toggle on/off the teletext mode
To select an external input for the TV screen
To start turbo sound
To start turbo picture
To enter adjustment mode when manufacturing the TV sets.
To adjust the screen voltage (automatic):
In-start
mute Adjust
AV(Enter into W/B adjustment mode)
W/B adjustment (automatic):
After adjusting the screen W/B adjustment Exit two times (Adjustment completed)
To enter into the adjustment mode. To adjust horizontal line and sub-brightness.
To select the multiple sound mode (Mono, Stereo or Foreign language)
To release the adjustment mode
To easily adjust the screen according to surrounding brightness
To easily adjust sound according to the program type
To check component input
To check the front AV
To move channel up/down or to select a function displayed on the screen.
To adjust the volume or accurately control a specific function.
To set a specific function or complete setting.
To move the channel down in the PIP screen.
To use as a red key in the teletext mode
To move the channel in the PIP screen
To use as a green key in the teletext mode
To switch between the main and sub screens
To use as a yellow key in the teletext mode
To select the input status in the PIP screen
To use as a blue key in the teletext mode
To set a function that will automatically adjust screen status to match
the surrounding brightness so natural color can be displayed.
To select the functions such as video, voice, function or channel.
To set the delivery condition status after manufacturing the TV set.
To halt the main screen in the normal mode, or the sub screen at the PIP screen.
Used as a hold key in the teletext mode (Page updating is stopped.)
Displays the teletext time in the normal mode
Enables to select the sub code in the teletext mode
Used as the size key in the PIP screen in the normal mode
Used as the size key in the teletext mode
Used as the index key in the teletext mode (Top index will be
displayed if it is the top text.)
To select the position of the PIP screen in the normal mode
Used as the update key in the teletext mode (Text will be
displayed if the current page is updated.)
Used as Mode in the teletext mode
To select the simultaneous screen
To adjust screen tilt
To manually select the channel.
Shortcut keys
Shortcut keys
Shortcut keys
Use the AV
key to enter
the screen
W/B
adjustment
mode.
Shortcut keys
Shortcut keys
Shortcut keys
Page 37
TROUBLESHOOTING
No power
(LED indicator off)
Check short of main B/D
or Change Lips
Change IC1107, IC1104
Change LED Assy
Check 15V or 5V
of Lips
Check Output of
IC1107, IC104
Check LED Assy
Check P1100, P210 Connector
Fail
Fail
Change Q1100
Check Output of
Q1100
Fail
Pass
Fail
Pass
Pass
Pass
:[A]Process
Page 38
No Raster
Check LED Status
on display unit
Check the input/
Output of IC901
Check L900,L901
L902,L903
Check inverter
Connector or inverter
Check input source cable and jack
Repeat A PROCESS
Fail
Change L900,L901,
L902,L903
Fail
Change IC901
Fail
Change inverter
connector or inverter
Fail
Change panel link
cable or module
Fail
Change module
Fail
Check panel link
Cable or module
Pass
Pass
Pass
Pass
:[B]Process
Page 39
No Raster on Component signal
Check JA1200 or
RCA CABLE
Check the signal of
L1200, L1202, L1203
Repeat
[A] Process
Check the input/
output of IC1
Check the input/
output of IC901
Check input source cable and jack
Fail
Re-soldering or
Change the defect part,
Check X11
Fail
Re-soldering or
Change the defect part,
Check X900
Fail
Pass
Pass
Pass
Check the input/output
of IC800, IC851
Re-soldering or
Change the defect part
Fail
Pass
Page 40
No Raster on AV Signal
(Video, S-Video)
No Raster on TV(RF) signal
Change L1209, L1210,
L1212
Check the signal of
L1209, L1210, L1212
Repeat
[A] Process
Check the output of
TU1000
Check the input/output
of IC1
Check the input/output
of IC800, IC851
Check input source cable and jack
Fail
Fail
Fail
Fail
Re-soldering or
Change the defect part
Chek X11
Fail
Re-soldering or
Change the defect part
Check 5V, 33V of TU1000
Re-soldering or
Change the defect part
Pass
Pass
Pass
Check the input/output
of IC901
Fail
Re-soldering or
Change the defect part
Check X900
Pass
Pass
Page 41
No Sound
Check the speaker wire
Change source input
Check the
input source
Fail
Pass
Re-soldering or
Change the defect part
Check X11
Check the input/output
of IC1
Fail
Pass
Re-soldering or
Change the defect part
Check the input/output
of IC100,IC101
Fail
Pass
Change speaker
Check the speaker
Fail
Pass
Page 42
BLOCK DIAGRAM
UT
LVDS 1 O
TTL 2 OUT
TTL 1 OUT
Audio Amp
IC100 IC101
IC905
AT49F
L, R
SIDE_AV
IC851
M52758FP
IC901
GM2221
PC RGB
SM5301BS IC800
RGB OUT
SIDE_L,R
LA7222 IC2
S
Z1000
IC1
VCTI
SIDE V
IF+,-
A
W
Tuner
TU1000
IC202
14066
PC L,R
PC
AUDIO
D-SUB
L,R
ML-041B Block Diagram
POWER
IC500
TC90A65F
DIGITAL SIGNAL
ANALOG SIGNAL
IF +,- INPUT
SOUND INPUT
SOUND OUTPUT
IC4
AT24C16
COMPONENT
SCART V,L,R
SCART R,G,B
V
S-VHS
H/P
b Pr
YP
AC IN
Page 43
BLOCK DIAGRAM DESCRIPTION
1. Video Controller Unit & Display Data Conversion Unit
The video controller unit receives the video signals inputted through the tuner, AV port (AV1, AV2, S-Video,
component), and converts them into an analog RGB signal through the microcomputer (VCTI) combined with
the video decoder that integrates various functions in one chip.
Either the analog RGB, component YPbPr or PC RGB signal is selected by the switching IC and inputted to a
scaler (GM2221), which is sent to the LCD module after being modified to an LVDS signal through the
integrated LVDS IC.
Or, it is sent to the LCD module as a TTL output.
VCTi is the main microprocessor that handles video signal processing and sound signal processing. It also
manages the RF signals received from the tuner.
The scaler can control timing to fit into the LCD panel, and can also control the size and position of the input
signal.
2. Power Supply Unit
The power supply unit provides 15V and 5V DC power to the mainboard.
The PWM Step-Up DC/DC Converter circuit is used to generate the 33V used for the tuner.
15V power is directly used by the sound amplifier IC and is also used to generate 5V power through the
regulator. 12V power is used for the LCD panel power, and 5V power is converted to 3.3V and 1.8V power
through the regulator, which in turn supplies electrical power for ICs such as VCTI and scaler.
Page 44
1. 20P LVDS : 200MM
WIRING DIAGRAM
No. Part No.
1
2
3
4
5
6
7
8
9
Wiring Part List
6631T25019Y
6631T11017P-CMO
6631T11017Q-AUO
6631T11021A
6631T11012R
6631T20028G
6631T20029X
6631T25021A
6620K00007C
or 6620K00007A
6631T11017R
2. 41P TTL
3. 50P TTL : 145MM
P904
P902
P901
2
4
6
P210
6P_2.0MM H-B
220MM
3P_2.5MM H-B
IR_LED
600MM
7
LOCAL KEY
3
5
11P_2.0MM H-H
100MM
1
P3
9
18P_1.0MM FFC
54MM
(RZ ONLY)
8
P1203
4P_2.5MM SHIELD RECEPTERCLE
GND: 2PIN, 4PIN
500MM 750MM
2P_AC_SOCKET
SPEAKER SPEAKER
Page 45
EXPLODED VIEW
16
15
4
3
12
10
21
22
19
17
18
14
11
13
9
8
2
20
6
7
5
1
5
Page 46
EXPLODED VIEW PARTS LIST
1 3091V00587A CABINET ASSEMBLY RZ-20LA70 NON NON ML024D
3091V00587C CABINET ASSEMBLY RZ-20LA70 STEREO ML024D C/SKD
2 6306V20002A LCD(LIQUID CRYSTAL DISPLAY), V201V1-T02 VGA CHIMEI TFT COLOR NON
6304FAU017A LCD(LIQUID CRYSTAL DISPLAY), A201SN01N01-V6 AU TFT COLOR TN 500NITS 16MS
3 3809TKD002R BACK COVER ASSEMBLY, RM-20LA70 3808V00427 FOR RUSSIA (ML041B)
3809TKD002M BACK COVER ASSEMBLY, RZ-20LA70 3808V00427 ML041B(SCART)
3809TKD002P BACK COVER ASSEMBLY, RM-20LA70 3808V00427 FOR RUSSIA(ML-041B)
4 4811V00073A BRACKET ASSEMBLY, STAND RZ-20LA70 NON .
4811V00073C BRACKET ASSEMBLY, STAND RZ-20LA70 ML024D C/SKD.
5 6400GKTX01C
SPEAKER,FULLRANGE, F1527C-6428-4 K-TONE FULL-RANGE(GENERAL) 4 OHM 7/12W 85DB OTHERS 40*70MM TRACK TYPE
6 6871TST562A
PWB(PCB) ASSEMBLY,SUB, RM-20LA77 ML041B SUB TOTAL BRAND CONTROL BOARD ASSY
7 6871TST563A PWB(PCB) ASSEMBLY,SUB, RM-20LA77 ML041B SUB TOTAL BRAND IR BOARD ASSY
8 4951TKS175C METAL ASSEMBLY, FRAME METAL, ASSY 20LA70(CMO)
4951TKS175A METAL ASSEMBLY, FRAME METAL, ASSY 20LA70(AUO)
4951TKS175E METAL ASSEMBLY, FRAME METAL, ASSY 20LA70(AUO,CKD)
4951TKS175G METAL ASSEMBLY, FRAME METAL, ASSY 20LA70(CMO, CKD)
9 3313TP2029A MAIN TOTAL ASSEMBLY, RZ-20LA70(CMO) BRAND ML-041B
10 6871TPT280A
PWB(PCB) ASSEMBLY,POWER, RM-20LA77 POWER TOTAL LIEN CHANG LIPS FOR CMO/AUO
11 6871TST615A PWB(PCB) ASSEMBLY,SUB, RZ-17LZ50 SUB TOTAL BRAND JACK(SCART) BOARD ASSY
12 4951TKK186E METAL ASSEMBLY, SHIELD REAR RZ-20LA70
4951TKK186F METAL ASSEMBLY, SHIELD REAR RZ-20LA70 CKD
13 4950TKK916B METAL, PLATE 15, 20LA70 REAR A/V "B" T
14 4810V00925B BRACKET, REAR AV RZ-15LA70 ML024E HIPS .
15 5020V00871A BUTTON, CONTROL RZ-20LA70 ABS 8KEY .
16 3550V00383A COVER, REAR AV RZ-20LA70 HIPS 60HR .
17 4950V00157E METAL, HINGE ASSY NON 20LA70
18 4810V00767A BRACKET, STAND 20LA60 ML012B NON HINGE FRONT
19 4810V00768A BRACKET, STAND 20LA60 ML012B NON HINGE COVER
20 4810V00924A BRACKET, STAND RZ-20LA70 NON ABS .
21 4950V00194A METAL, STAND SPCC(CR) SUPPORTER(LA70)
22 4950V00193A METAL, STAND SPCC(CR) BASE(20LA70)
No.
PART NO.
DESCRIPTION
Page 47
- 22 -
DATE: 2004. 6. 16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C1008 0CE227CF638 "220UF SHL,SD 16V M FM5 TP 5"
C1101 0CE227BH638 220U KME 25V M FM5 TP5
C1104 0CE227BH638 220U KME 25V M FM5 TP5
C1107 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C1140 0CE227BH638 220U KME 25V M FM5 TP5
C1152 0CE107BK638 100UF KME 50V M FM5 TP5
C123 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C124 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C131 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C132 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C133 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C134 0CE477BH618 470UF KME TYPE 25V M FL TP 5
C1150 0CH3105F946 1UF 16V Z F 2012 R/TP
C1151 0CH3104K946 100000PF 50V Z F 2012 R/TP
C127 0CH3104K946 100000PF 50V Z F 2012 R/TP
C128 0CH3104K946 100000PF 50V Z F 2012 R/TP
C135 0CH3104K946 100000PF 50V Z F 2012 R/TP
C136 0CH3104K946 100000PF 50V Z F 2012 R/TP
C15 0CH3104K946 100000PF 50V Z F 2012 R/TP
C16 0CH3104K946 100000PF 50V Z F 2012 R/TP
C19 0CH3104K946 100000PF 50V Z F 2012 R/TP
C203 0CH3104K946 100000PF 50V Z F 2012 R/TP
C4 0CH3104K946 100000PF 50V Z F 2012 R/TP
C41 0CH3104K946 100000PF 50V Z F 2012 R/TP
C44 0CH3104K946 100000PF 50V Z F 2012 R/TP
C49 0CH3104K946 100000PF 50V Z F 2012 R/TP
C6 0CH3104K946 100000PF 50V Z F 2012 R/TP
C803 0CH3105F946 1UF 16V Z F 2012 R/TP
C804 0CH3104K946 100000PF 50V Z F 2012 R/TP
C808 0CH3104K946 100000PF 50V Z F 2012 R/TP
C810 0CH3104K946 100000PF 50V Z F 2012 R/TP
C812 0CH3105F946 1UF 16V Z F 2012 R/TP
C851 0CH3104K946 100000PF 50V Z F 2012 R/TP
C854 0CH3104K946 100000PF 50V Z F 2012 R/TP
C855 0CH3104K946 100000PF 50V Z F 2012 R/TP
C858 0CH3104K946 100000PF 50V Z F 2012 R/TP
C863 0CH3104K946 100000PF 50V Z F 2012 R/TP
C866 0CH3104K946 100000PF 50V Z F 2012 R/TP
C867 0CH3104K946 100000PF 50V Z F 2012 R/TP
C869 0CH3104K946 100000PF 50V Z F 2012 R/TP
C871 0CH3104K946 100000PF 50V Z F 2012 R/TP
C874 0CH3104K946 100000PF 50V Z F 2012 R/TP
C875 0CH3104K946 100000PF 50V Z F 2012 R/TP
C877 0CH3104K946 100000PF 50V Z F 2012 R/TP
C909 0CH3104K946 100000PF 50V Z F 2012 R/TP
C910 0CH3104K946 100000PF 50V Z F 2012 R/TP
C917 0CH3104K946 100000PF 50V Z F 2012 R/TP
C920 0CH3104K946 100000PF 50V Z F 2012 R/TP
C925 0CH3104K946 100000PF 50V Z F 2012 R/TP
C926 0CH3104K946 100000PF 50V Z F 2012 R/TP
C927 0CH3104K946 100000PF 50V Z F 2012 R/TP
C928 0CH3104K946 100000PF 50V Z F 2012 R/TP
C929 0CH3104K946 100000PF 50V Z F 2012 R/TP
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C930 0CH3104K946 100000PF 50V Z F 2012 R/TP
C934 0CH3104K946 100000PF 50V Z F 2012 R/TP
C935 0CH3104K946 100000PF 50V Z F 2012 R/TP
C936 0CH3104K946 100000PF 50V Z F 2012 R/TP
C937 0CH3104K946 100000PF 50V Z F 2012 R/TP
C938 0CH3104K946 100000PF 50V Z F 2012 R/TP
C939 0CH3104K946 100000PF 50V Z F 2012 R/TP
C940 0CH3104K946 100000PF 50V Z F 2012 R/TP
C943 0CH3104K946 100000PF 50V Z F 2012 R/TP
C944 0CH3104K946 100000PF 50V Z F 2012 R/TP
C945 0CH3104K946 100000PF 50V Z F 2012 R/TP
C946 0CH3104K946 100000PF 50V Z F 2012 R/TP
C947 0CH3104K946 100000PF 50V Z F 2012 R/TP
C948 0CH3104K946 100000PF 50V Z F 2012 R/TP
C949 0CH3104K946 100000PF 50V Z F 2012 R/TP
C950 0CH3104K946 100000PF 50V Z F 2012 R/TP
C956 0CH3104K946 100000PF 50V Z F 2012 R/TP
C964 0CH3104K946 100000PF 50V Z F 2012 R/TP
C965 0CH3104K946 100000PF 50V Z F 2012 R/TP
C967 0CH3104K946 100000PF 50V Z F 2012 R/TP
C968 0CH3104K946 100000PF 50V Z F 2012 R/TP
C970 0CH3104K946 100000PF 50V Z F 2012 R/TP
C13 0CH6102K406 1000PF 50V J SL 2012 R/TP
C14 0CH6102K406 1000PF 50V J SL 2012 R/TP
C2 0CH6102K406 1000PF 50V J SL 2012 R/TP
C20 0CH6102K406 1000PF 50V J SL 2012 R/TP
C21 0CH6102K406 1000PF 50V J SL 2012 R/TP
C46 0CH6102K406 1000PF 50V J SL 2012 R/TP
C50 0CH6102K406 1000PF 50V J SL 2012 R/TP
C59 0CH6102K406 1000PF 50V J SL 2012 R/TP
C7 0CH6221K416 220PF 50V J NP0 2012 R/TP
C8 0CH6221K416 220PF 50V J NP0 2012 R/TP
C9 0CH6221K416 220PF 50V J NP0 2012 R/TP
C923 0CH6050K116 5PF 50V D NP0 2012 R/TP
C924 0CH6050K116 5PF 50V D NP0 2012 R/TP
C129 181-007F "MPE ECQ-V1H224JL3(TR), 50V 0."
C130 181-007F "MPE ECQ-V1H224JL3(TR), 50V 0."
C1003 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1007 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1010 0CK273DK51A 27000PF 2012 50V 10% B(Y5P) R
C1015 0CH5390K416 39PF 50V 5% NP0 2012 R/TP
C1016 0CH5390K416 39PF 50V 5% NP0 2012 R/TP
C107 0CK225DFK4A "2.2UF 2012 16V 20%,-20% F(Y5V"
C109 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C110 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C113 0CK225DFK4A "2.2UF 2012 16V 20%,-20% F(Y5V"
C900 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C902 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C955 0CH5390K416 39PF 50V 5% NP0 2012 R/TP
C1001 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C1002 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C1004 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C11 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C114 0CK225DFK4A "2.2UF 2012 16V 20%,-20% F(Y5V"
REPLACEMENT PARTS LIST
MAIN BOARD
CAPACITOR
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit in the
P/No. means as follows;
CC, CX, CK, CN, CH : Ceramic
CQ : Polyestor
CE : Electrolytic
CF : Fixed Film
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RH : CHIP, Metal Glazed(Chip)
RR : Drawing
Page 48
- 23 -
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C115 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C116 0CK562CK51A 5600PF 1608 50V 10% R/TP B(Y5
C117 0CK562CK51A 5600PF 1608 50V 10% R/TP B(Y5
C118 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C12 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C125 0CK105EK56A 1UF 3216 50V 10% X7R R/TP
C126 0CK105EK56A 1UF 3216 50V 10% X7R R/TP
C200 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C22 0CK822CK56A 8200PF 1608 50V 10% X7R R/TP
C23 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C24 0CK822CK56A 8200PF 1608 50V 10% X7R R/TP
C25 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C26 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C27 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C28 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C29 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C3 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C30 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C31 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C32 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C33 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C34 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C35 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C37 0CK334CF94A "0.33UF 1608 16V 80%,-20% F(Y5"
C40 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C42 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C45 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C52 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C67 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C75 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C800 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F("
C801 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F("
C802 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F("
C807 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C811 0CK105CF94A "1UF 1608 16V 80%,-20% R/TP F("
C816 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C82 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C861 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C865 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C901 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C903 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C904 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C905 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C906 0CK103CK51A 0.01UF 1608 50V 10% R/TP B(Y5
C911 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C912 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C913 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C914 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C915 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C916 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C918 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C919 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C921 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C922 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C961 0CK104CK56A 0.1UF 1608 50V 10% R/TP X7R
C121 0CC100CK41A 10PF 1608 50V 5% R/TP NP0
C122 0CC100CK41A 10PF 1608 50V 5% R/TP NP0
C43 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C47 0CC220CK41A 22PF 1608 50V 5% R/TP NP0
C48 0CC220CK41A 22PF 1608 50V 5% R/TP NP0
C53 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C56 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C57 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C58 0CC221CK41A 220PF 1608 50V 5% R/TP NP0
C74 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C83 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C85 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C86 0CC102CK41A 1000PF 1608 50V 5% R/TP NP0
C88 0CC390CK41A 39PF 1608 50V 5% R/TP NP0
C889 0CC331CK41A 330PF 1608 50V 5% R/TP NP0
C89 0CC390CK41A 39PF 1608 50V 5% R/TP NP0
C890 0CC331CK41A 330PF 1608 50V 5% R/TP NP0
C891 0CC331CK41A 330PF 1608 50V 5% R/TP NP0
C1 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1106 0CE477BD618 470UF KME TYPE 10V 20% FL TP
C108 0CE476VH6DC 47UF MV 25V 20% R/TP(SMD) SMD
C1102 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1103 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1105 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C1109 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C111 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C1118 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C112 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C1124 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1130 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1132 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1134 0CE227WF6DC 220UF MVK 16V 20% R/TP(SMD) S
C1135 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1137 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1149 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C119 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C120 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
C17 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C5 0CE475WJ6DC 4.7UF MVK 35V 20% R/TP(SMD) S
C55 0CE475VK6DC 4.7UF MV 50V 20% R/TP(SMD) SM
C60 0CE475VK6DC 4.7UF MV 50V 20% R/TP(SMD) SM
C852 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C856 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C859 0CH8476F691 47UF 16V 20% 105STD (CYL) R/T
C87 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C876 0CH8106F691 10UF 16V 20% 105STD (CYL) R/T
D100 0DRFC00288A SS14 FAIR CHILD R/TP SMA 20-1
D101 0DRFC00288A SS14 FAIR CHILD R/TP SMA 20-1
D1150 0DRGS00199A UF4001 GENERAL SEMICONDUCTOR
D102 0DS181009AA KDS181 TP KEC SOT-23 80V 30
D103 0DS181009AA KDS181 TP KEC SOT-23 80V 30
D107 0DS226009AA KDS226 TP KEC SOT-23 80V 300
ZD104 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD105 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD207 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD208 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD209 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD211 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD200 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD201 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD202 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD203 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD204 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD205 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
ZD206 0DZ510009EE UDZ S 5.1B TP ROHM-K SOD323 2
D1151 0DZ330009DF MTZJ33B TP ROHM-K DO34 0.5W 3
DIODEs
Page 49
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
IC905 0IZZTSA003A
ML-041B VGA PAL ATMEL 32P PLC-CMO
IC905 0IZZTSA005A
ML-041B VGA PAL ATMEL 32P PLC-AUO
IC3 0IKE702700D "KIA7027AF 3, SOT-89 TP RESET"
IC200 0IMMRSG036A "M24C02-WMN6T SGS-THOMSON 8P,S"
IC4 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P S
IC903 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P S
IC100 0IMCRMZ002A MP7720 MONOLITHIC POWER SYSTE
IC101 0IMCRMZ002A MP7720 MONOLITHIC POWER SYSTE
IC202 0IMO140662A "MC14066BDR2 14P,SOIC TP BILAT"
IC1 0IPRPMN003C VCT49XYF C7(NTSC+PAL) MICRONA
IC901 0IPRPGN015A "GM2221 GENESIS 208P,QFP TRAY"
IC1101 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1103 0IPMGSG018D "LD1086DT18TR SGS-THOMSON 3P,D"
IC1108 0IMCRKE010A KIA7812AF KEC 2P DPACK R/TP 1
IC1111 0IMCRFA015A KA7805R FAIRCHILD 2P D-PAK R/
IC1105 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1106 0IPMGSG018D "LD1086DT18TR SGS-THOMSON 3P,D"
IC1114 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1115 0IPMGFA061A "FAN1587AD33X FAIRCHILD 3P,DPA"
IC1110 0ISS780800J "KA78M08R 3P,D-PAK TP VOL. REG"
IC1113 0ISS780800J "KA78M08R 3P,D-PAK TP VOL. REG"
L104 6140TBZ045A "38.5UH(DIP), 6A, P7.5, DR8.3X"
L105 6140TBZ045A "38.5UH(DIP), 6A, P7.5, DR8.3X"
L1150 150-985B DR8*11 2.4MH 0.16MM 270.5T
L1100 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1101 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1103 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1104 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1105 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1106 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1107 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L200 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L201 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L202 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L203 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L204 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L853 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L900 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L901 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L902 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L903 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L1102 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L205 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L800 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L906 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L907 6210TCE001G HH-1M3216-501 CERATEC 3216MM
L10 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L1001 0LC1020101A 1UH 10% 2012 R/TC FI-B2012-10
L1002 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L15 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L2 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L8 0LC1032101A 10UH 10% 3216 R/TC FI-C3216-1
L888 0LC0233002A 3.3UH CERATECH R/TP
L889 0LC0233002A 3.3UH CERATECH R/TP
L890 0LC0233002A 3.3UH CERATECH R/TP
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
IC1107 0TF492509AA SI4925DY TP TEMIC 30V 6.1A S
Q1150 0TR322809AB KTC3228-Y(KTC2383) TP KEC TO9
Q1 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q603 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q1000 0TR388109AA KTC3881 CHIP TP KEC - Q101 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q1100 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q1151 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q12 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q13 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q14 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - Q15 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q2 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q3 0TR150400BA CHIP 2SA1504S(ASY) BK KEC - IC902 0TFVI80005A VISHAY SI4963DY R/TP SO-8 -20
IC1104 0TFVI80005A VISHAY SI4963DY R/TP SO-8 -20
R1004 0RH3000D622 300 1/10W 5 D.R/TP
R1010 0RH7501D622 7.5K 1/10W 5 D.R/TP
R1012 0RH7502D622 75K 1/10W 5 D.R/TP
R106 0RH1500D622 150 1/10W 5 D.R/TP
R107 0RH1003D622 100K 1/10W 5 D.R/TP
R1151 0RH4700D622 470 1/10W 5 D.R/TP
R1153 0RH1000D622 100 1/10W 5 D.R/TP
R126 0RH4701D622 4.7K 1/10W 5 D.R/TP
R132 0RH1003D622 100K 1/10W 5 D.R/TP
R133 0RH1003D622 100K 1/10W 5 D.R/TP
R134 0RH1003D622 100K 1/10W 5 D.R/TP
R135 0RH1003D622 100K 1/10W 5 D.R/TP
R14 0RH4701D622 4.7K 1/10W 5 D.R/TP
R140 0RH0392D622 39 1/10W 5 D.R/TP
R141 0RH0392D622 39 1/10W 5 D.R/TP
R142 0RH0392D622 39 1/10W 5 D.R/TP
R143 0RH0392D622 39 1/10W 5 D.R/TP
R144 0RH0392D622 39 1/10W 5 D.R/TP
R145 0RH0392D622 39 1/10W 5 D.R/TP
R146 0RH0392D622 39 1/10W 5 D.R/TP
R147 0RH0392D622 39 1/10W 5 D.R/TP
R201 0RH4701D622 4.7K 1/10W 5 D.R/TP
R204 0RH4701D622 4.7K 1/10W 5 D.R/TP
R211 0RH0752D622 75 1/10W 5 D.R/TP
R212 0RH0752D622 75 1/10W 5 D.R/TP
R213 0RH0752D622 75 1/10W 5 D.R/TP
R214 0RH4703D622 470K 1/10W 5 D.R/TP
R217 0RH4703D622 470K 1/10W 5 D.R/TP
R57 0RH1000D622 100 1/10W 5 D.R/TP
R59 0RH1201D622 1.2K 1/10W 5 D.R/TP
R6 0RH4702D622 47K 1/10W 5 D.R/TP
R818 0RH8200D622 820 1/10W 5 D.R/TP
R9 0RH4701D622 4.7K 1/10W 5 D.R/TP
R908 0RH0822D622 82 1/10W 5 D.R/TP
R910 0RH0822D622 82 1/10W 5 D.R/TP
R915 0RH3600D622 CHIP 360-J 1/10 W
R934 0RH1000D622 100 1/10W 5 D.R/TP
R989 0RH8200D622 820 1/10W 5 D.R/TP
R999 0RH1000D622 100 1/10W 5 D.R/TP
R136 0RH8202D622 82K 1/10W 5 D.R/TP
R137 0RH8202D622 82K 1/10W 5 D.R/TP
- 24 -
IC
COIL & CORE & INDUCTOR
FET & TRANSISTOR
RESISTORs
Page 50
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
C931 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
C932 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
C933 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
L905 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R1002 0RH1501D622 1.5K OHM 1 / 10 W 2012 5.00%
R1011 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R1106 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R1152 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R12 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R128 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R129 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R13 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R202 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R208 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R209 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R210 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R36 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R37 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R7 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R817 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R822 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R834 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R836 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R837 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R961 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
R964 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R1 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R10 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R1001 0RJ0562D677 56 OHM 1/10 W 5% 1608 R/TP
R1003 0RJ8200D677 820 OHM 1/10 W 5% 1608 R/TP
R1005 0RJ0682D677 68 OHM 1/10 W 5% 1608 R/TP
R1014 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R11 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R1105 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R1107 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R1149 0RH1002D622 10K OHM 1 / 10 W 2012 5.00% D
R1150 0RJ0102D677 10 OHM 1/10 W 5% 1608 R/TP
R124 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R125 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R127 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP
R130 0RJ1202D677 12K OHM 1/10 W 5% 1608 R/TP
R131 0RJ1202D677 12K OHM 1/10 W 5% 1608 R/TP
R138 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R139 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R15 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R16 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP
R17 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R18 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP
R19 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R2 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R20 0RJ2200D677 220 OHM 1/10 W 5% 1608 R/TP
R203 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R205 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP
R206 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R207 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R21 0RJ0222D677 22 OHM 1/10 W 5% 1608 R/TP
R22 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R221 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R224 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R225 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R226 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R23 0RJ2701D677 2.7K OHM 1/10 W 5% 1608 R/TP
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R24 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R240 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R25 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R28 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R29 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R3 0RJ4700D677 470 OHM 1/10 W 5% 1608 R/TP
R34 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R4 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R41 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R45 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R46 0RJ1001D677 1K OHM 1/10 W 5% 1608 R/TP
R49 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R5 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R50 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R51 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R52 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R53 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R54 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R55 0RJ1500D677 150 OHM 1/10 W 5% 1608 R/TP
R56 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R58 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R60 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R62 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R64 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R66 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R68 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R69 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R70 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R72 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R73 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R74 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R75 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R76 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R77 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R78 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R8 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R80 0RJ2202D677 22K OHM 1/10 W 5% 1608 R/TP
R888 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R889 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R890 0RJ0752D677 75 OHM 1/10 W 5% 1608 R/TP
R901 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R902 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R904 0RJ0472D677 47 OHM 1/10 W 5% 1608 R/TP
R907 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R909 0RJ0822D677 82 OHM 1/10 W 5% 1608 R/TP
R911 0RJ4701D677 4.7K OHM 1/10 W 5% 1608 R/TP
R912 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R913 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R914 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R917 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R928 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R929 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R930 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R931 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R932 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R935 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R936 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R938 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R939 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R940 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R941 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R942 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
- 25 -
Page 51
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R943 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R944 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R945 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R946 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R947 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R952 0RJ0000D677 0 OHM 1/10 W 5% 1608 R/TP
R953 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R954 0RJ1002D677 10K OHM 1/10 W 5% 1608 R/TP
R96 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R979 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R980 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R981 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R982 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R983 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R984 0RJ1000D677 100 OHM 1/10 W 5% 1608 R/TP
R991 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
R992 0RJ3301D677 3.3K OHM 1/10 W 5% 1608 R/TP
Z1000 6200QL3002F "X6966M EPCOS ST SIP5K, 6200QL"
X11 6202VDT002E SX-1SMD SUNNY RADIAL 20250000
X900 6202VDT002B SX-1 SUNNY SC14.3MHZ +/- 30 P
IC905 6620F00017A CCSD-32T-SM WOOYOUNG 32P PLCC
TU1000 6700VS0003A TAEW-G051D LG INOTEK MULTI VS
R2200 0RN1101F409 1.10K 1/6W 1% TA52
R2201 0RN8200F409 820 1/6W 1% TA52
R2202 0RN5600F409 560 1/6W 1% TA52
R2203 0RN4700F409 470 1/6W 1 TA52
R2204 0RN3900F409 390 1/6W 1% TA52
R2205 0RN3300F409 330 1/6W 1% TA52
R2206 0RN2700F409 270 1/6W 1% TA52
R2207 0RN3301F409 3.30K 1/6W 1% TA52
R2208 0RN2000F409 200 1/6W 1% TA52
SW2200 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2201 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2202 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2203 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2204 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2205 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2206 140-313A TACT 2LEAD 100G(TA) LG C&D NO
SW2207 140-313A TACT 2LEAD 100G(TA) LG C&D NO
C2101 0CH3104K566 0.1UF 50V 10% X7R 2012 R/TP
L2101 6210TCE001A HB-1S2012-080JT CERATEC 2012M
LED2100
0DL200000CA SAM5670(DL-2LRG) BK Y-GREEN PA2101 6726TV0001A TSOP4838SO1 VISHAY 38.0KHZ HO
R2101 0RH1000D622 100 1/10W 5 D.R/TP
R2102 0RH1000D622 100 1/10W 5 D.R/TP
R2106 0RH1000D622 100 1/10W 5 D.R/TP
R2111 0RH4301D622 4.3K 1/10W 5 TA
R2103 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R2104 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R2105 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R2113 0RH0000D622 0 OHM 1 / 10 W 2012 5.00% D
Q2101 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - Q2102 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
Q2103 0TR387500AA CHIP 2SC3875S(ALY) BK KEC - -
C1217 0CH3104K946 100000PF 50V Z F 2012 R/TP
C1201 0CH6221K416 220PF 50V J NP0 2012 R/TP
C1202 0CH6101K416 100PF 50V J NP0 2012 R/TP
C1207 0CH6471K416 470F 50V J NP0 2012 R/TP
C1208 0CH6471K416 470F 50V J NP0 2012 R/TP
C1221 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1223 0CH6471K416 470F 50V J NP0 2012 R/TP
C1224 0CH6471K416 470F 50V J NP0 2012 R/TP
C1210 0CH6471K416 470F 50V J NP0 2012 R/TP
C1212 0CH6471K416 470F 50V J NP0 2012 R/TP
C1213 0CH6101K416 100PF 50V J NP0 2012 R/TP
C1214 0CH6101K416 100PF 50V J NP0 2012 R/TP
C1218 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1219 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1220 0CH6331K416 330PF 50V J NP0 2012 R/TP
C1215 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1216 0CH3103K516 10000PF 50V 10% B(Y5P) 2012 R
C1200 0CE107WF6DC 100UF MVK 16V 20% R/TP(SMD) S
C1209 0CH8226F691 22UF 16V 20% 105STD (CYL) R/T
C1211 0CH8226F691 22UF 16V 20% 105STD (CYL) R/T
L1202 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1203 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1206 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1207 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1208 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1211 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1213 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1214 6210TCE001A HB-1S2012-080JT CERATEC 2012M
L1215 6210TCE001A HB-1S2012-080JT CERATEC 2012M
ZD1200 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1206 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1207 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1212 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1213 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1214 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1210 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1211 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1215 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1216 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1217 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1218 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
ZD1219 0DZ620009HB UDZ S 6.2B TP ROHM SOD323 200
L1200 0LC1020101A 1UH 10% 2012 R/TC FI-B2012-10
L1212 0LC0233002A 3.3UH CERATECH R/TP
L1209 0LC0233002A 3.3UH CERATECH R/TP
L1210 0LC0233002A 3.3UH CERATECH R/TP
JA1201 6613V00008F PMJ014F PARK ELEC E/P(ST)+S-V
JA1200 381-091C UPJ-R1-019 UGCOM 21PIN W/SHIE
R1200 0RH0682D622 68 1/10W 5 D.R/TP
R1202 0RH0752D622 75 1/10W 5 D.R/TP
R1206 0RH0752D622 75 1/10W 5 D.R/TP
R1217 0RH4703D622 470K 1/10W 5 D.R/TP
R1218 0RH5101D622 5.1K 1/10W 5 D.R/TP
R1219 0RH5101D622 5.1K 1/10W 5 D.R/TP
R1220 0RH4703D622 470K 1/10W 5 D.R/TP
R1230 0RH0752D622 75 1/10W 5 D.R/TP
R1231 0RH0752D622 75 1/10W 5 D.R/TP
R1232 0RH5101D622 5.1K 1/10W 5 D.R/TP
- 26 -
OTHERs
CONTROL BOARD
IR BOARD
JACK BOARD
Page 52
DATE: 2004. 06.16.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
R1233 0RH4703D622 470K 1/10W 5 D.R/TP
R1234 0RH5101D622 5.1K 1/10W 5 D.R/TP
R1235 0RH4703D622 470K 1/10W 5 D.R/TP
R1236 0RH1802D622 18K 1/10W 5 D.R/TP
R1237 0RH1802D622 18K 1/10W 5 D.R/TP
L1204 0RH3001D622 3.0K 1/10W 5 D.R/TP
L1205 0RH3001D622 3.0K 1/10W 5 D.R/TP
R1203 0RH0752D622 75 1/10W 5 D.R/TP
R1204 0RH0752D622 75 1/10W 5 D.R/TP
R1207 0RH0752D622 75 1/10W 5 D.R/TP
R1210 0RH0752D622 75 1/10W 5 D.R/TP
R1212 0RH0752D622 75 1/10W 5 D.R/TP
R1214 0RH0752D622 75 1/10W 5 D.R/TP
R1216 0RH5102D622 51K 1/10W 5 D.R/TP
R1226 0RH0472D622 47 1/10W 5 D.R/TP
R1227 0RH0752D622 75 1/10W 5 D.R/TP
R1228 0RH0752D622 75 1/10W 5 D.R/TP
R1229 0RH0752D622 75 1/10W 5 D.R/TP
R1201 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R1205 0RH0222D622 22 OHM 1 / 10 W 2012 5.00% D
R1224 0RJ1000H680 100 OHM 1/2 W 5% 5025 R/TP
R1225 0RJ1000H680 100 OHM 1/2 W 5% 5025 R/TP
R1215 0RH3902D622 39K OHM 1 / 10 W 2012 5.00% D
R1221 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
R1222 0RH1001D622 1K OHM 1 / 10 W 2012 5.00% D
P1205 6620K00007C "ISHENG,7007,M.MOUSE,60MM,YH39"
- 27 -
Page 53
Page 54
Page 55
Jun., 2004
Printed in KoreaP/NO : 3828TSL103L
Loading...