LG RU-52SZ53D, RU-44SZ63D User Manual

DLP Projection TV

OWNER’S MANUAL

Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this
information to your dealer when you require service.

MODELS: RU-44SZ63D

RU-52SZ53D

LG Electronics U.S.A., Inc.

PAGE 2

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip­ment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio com­munications. However, there is no guarantee that interference will not occur in a particular installation. If this equip­ment does cause harmful interference to radio or television reception, which can be determined by turning the equip­ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-201-816-2000
http://www.lgusa.com

WARNING

RISK OF ELECTRIC SHOCK
DO NOT OPEN

PAGE 3

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical
shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and
observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation
that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

1. Read Instructions

All the safety and operating instructions should be read
before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained
for future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc­tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a
bath tub, wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface,
or on an unstable cart, stand, tripod, bracket, or table.
The product may slide or fall, causing serious injury to a
child or adult, and serious damage to the product. Use
only with a cart, stand, tripod, bracket, or table recom­mended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufac­turer’s instructions, and should use a mounting accessory
recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product
manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila­tion and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not
be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in
a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home, con­sult your product dealer or local power company. For prod­ucts intended to operate from battery power, or other
sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a polarized alternating-cur­rent line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety pur­pose of the polarized plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.

IMPORTANT SAFETY INSTRUCTIONS

PORTABLE CART WARNING

PAGE 4

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded
to provide protection against voltage surges and built-up
static charges. Article 810 of the National Electrical Code
(U.S.A.), ANSI/ NFPA 70 provides information with regard
to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna­discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a
lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.

16. Power Lines

An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be
fatal.

17. Overloading

Do not overload wall outlets and extension cords as this
can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servic­ing to qualified service personnel under the following con­ditions:

a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into

the product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation.

e. If the product has been dropped or the cabinet has
been damaged.

f. If the product exhibits a distinct change in perfor­mance.

21. Replacement Parts

When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or have the same characteristics as the origi­nal part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condi­tion.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide
or fall, causing serious injury to a child or adult, and seri­ous damage to the product.

24. Heat

The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.

Antenna Lead in Wire

Antenna Discharge Unit
(NEC Section 810-20)

Grounding Conductor
(NEC Section 810-21)

Ground Clamps

Power Service Grounding
Electrode System (NEC
Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical
Code Instructions

Fig. 1

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

PAGE 5

Table of Contents

Setup Checklist

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Important Safety Instructions . . . . . . . . . . . . . . . . .3-4

Function Status Indicators . . . . . . . . . . . . . . . . . . . . .6

Step 1. Hook Up TV

Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . .7

Front Connections Panel . . . . . . . . . . . . . . . . . . . . . .8

ANT/Cable Service Hookup . . . . . . . . . . . . . . . . . . . . .9

Cable Box Connections . . . . . . . . . . . . . . . . . . . . . . .10

VCR Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .11

DVD Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

RGB-DTV/DVI-DTV Input . . . . . . . . . . . . . . . . . . . . . .13

RGB-PC/DVI-PC Input . . . . . . . . . . . . . . . . . . . . . . .14

External Stereo Connections . . . . . . . . . . . . . . . . . . .15

Home Theater: Speaker Layout . . . . . . . . . . . . . . . . .16

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . . . . .17

Remote Control Functions in TV Mode . . . . . . . . . . .18-19

On-Screen Displays . . . . . . . . . . . . . . . . . . . . . . . . .20

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . .21

Step 2. Customize your TV’s Features

SETUP Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . . . . . .22

Channel Add/Delete/Surf Setup . . . . . . . . . . . . . . . .23

Channel Labels Setup . . . . . . . . . . . . . . . . . . . . . . .24

Main Picture Source Selection . . . . . . . . . . . . . . . . . 25

PIP (Picture-in-Picture) / Twin Picture Operation . . . . . .26

POP (Picture-outside-Picture) . . . . . . . . . . . . . . . . .27

Booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

VIDEO Menu Options . . . . . . . . . . . . . . . . . . . . .29-30

AUDIO Menu Options . . . . . . . . . . . . . . . . . . . . .31-32

TIME Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . .33

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . .34

TV Turn Off Timer Setup . . . . . . . . . . . . . . . . . . . . .35

TV Turn On Timer Setup . . . . . . . . . . . . . . . . . . . . .36

Sleep Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . .37

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

SPECIAL Menu Options

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

On-Screen Menu Languages . . . . . . . . . . . . . . . . . . 40

Captions Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Caption/Text Mode Selection . . . . . . . . . . . . . . . . . .42

Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . . . . .44

Demo (Menu Review) . . . . . . . . . . . . . . . . . . . . . . .45

LOCK Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . . . . .46

Parental Lock (Ratings Overview) . . . . . . . . . . . . . . .47

Step 3. Miscellaneous

Programming the Remote . . . . . . . . . . . . . . . . . . . . .48

Programming Codes . . . . . . . . . . . . . . . . . . . . . .49-52

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .54-55

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56-57

Product Specifications . . . . . . . . . . . . . . . . . . . . . .58

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59-60

Step 1. Make all equipment and source connections.
See pages 10-17.

Step 2. Install batteries in remote control and do a channel search.
See page 22.

Step 3. Adjust TV features and options to your preference.
See contents above.

Note: Design and specifications are subject to change without prior notice.

PAGE 6

Function Status Indicators

Lamp indicator, operation indicator, and temperature indicator located below the front panel controls,

reveal the operating status of the DLP projection TV.

Operation Indicator

Lamp Indicator

Temperature Indicator

ff Power cord is not connected.
Red Power Cord is connected, TV is in standby mode.
Green TV turns on.
Orange (flashing) Preparing operation in standby mode.
Orange Projection lamp is reaching the end of its life and needs to

be replaced with a new lamp. Contact your service center.

Red (flashing) There is a problem with the lamp or around it. Contact an

authorized service center.
Green (flashing) The lamp cover is not closed.
Orange The projection TV is overheating. Check the blocked vents of

the projection TV and the accumulated dust in the dust filter.
Red The projection TV shut down due to overheating.
Red (flashing) The projection TV shut down, check the cooling fan. Contact

your service center.

Operation Indicator

Lamp Indicator

Temperature Indicator

Rear Connections Panel

PAGE 7

Mini glossary

JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are color-

coded.

SIGNAL Picture and sound traveling through cable, or over the air, to your television screen.

C
A
L
I
B
R
A
T
I
O
N

PC/DTV
(XGA
/480p
/720p
/1080i)

AUDIO

CENTER

MODE IN

P

R

DVI INPUT

DTV/DVD INPUT

COMPONENT

INPUT2 INPUT1

PB

Y

PC/DTV
(XGA
/480p
/720p
/1080i)

RGB INPUT

RGB/DVI INPUT

(R)

(L)

AUDIO

(R)

(L)

AUDIO

(R)

(L)

AUDIO

V
A
R
I
A
B
L
E

A
U
D
I
O

O
U
T

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

S-VIDEO In

A connection available with
some high-end equipment
that provides even better
picture quality for Video 2.

Variable Audio Out

Used to connect either
an external amplifier, or
add a sub-woofer to your
surround sound system.

RF Connector: Antenna

Used to connect analog
cable or antenna signals to
the television, either
directly or through your
cable box.

Video 1 or 2

Connects the video sig­nals from various types of
equipment.

Y, Pb, Pr

DVD Component Video and HD

Component Video

Some top-of-the-line DVD players use what

is called “component video,” for extremely

accurate picture reproduction. Refer to

your DVD manual for further information.

Connecting cables and external equipment to your TV.

This manual explains the features available
on the RU-44SZ63D TVs.

Monitor Out

Connects to a second TV or
Monitor

.

Left/Right Audio

Used for stereo sound
from various types of
equipment.

PC and HD-STB Input

Used to connect from a PC

source or HD-STB Satellite

system.

PC and HD-STB Audio

Input

Used for audio connections

from a PC source or HD-STB

Satellite system.

Audio Center Mode In

Connect to external Dolby
Digital Center “preamp out­put.”

PAGE 8

Front Connection Panel

There are four jacks on the left side on your projection TV that
make connecting Audio/Video devices like video games and cam­corders very simple.

The jacks are like those found on the back jack connection panel.
This means that most equipment that connects to those types of
jacks on the rear jackpack, may be connected to the front con­nection panel.

To use the front jacks as the signal source, select them using
Main Input menu as described on page 25. They will be named
“Front Video” in the Main Input menu.

If you input both Front Video and S­Video, only the S-Video will work.

If you’re connecting a video game
device, make sure to change the
picture settings with the EZ Picture
option in the Video menu (see page

29).

Mini glossary

A/V CABLES Audio/Video cables. Three cable connector—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo

playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).

Left/Right Audio

Used for stereo sound

from various types of

equipment.

Video

Connects the video

signals from any

piece of equipment.

S-Video

A connection available on
some very high-end equipment
that provides better picture
quality than video input.

Front A/V Panel

(R)

AUDIO

(L)/
M

VIDEO

S-VIDEO

FRONT A/V

ONO

PAGE 9

ANT / Cable Service Hookup

1

Connect an antenna or cable service to your
TV as shown.

Turn to page 22 to do a channel search
with EZ Scan for Ant/Cable connection(s).

For best signal reception, it is recommended to have your Antenna professionally adjusted.

2

If you receive your RF signal
through an antenna that is several
years old and connects with two
small prongs, you will need to pur­chase a 300 to 75 ohm adapter. It
should be available from your local
electronics dealer.

We recommend using a 75 ohm
cable for your antenna connections
in order to prevent
interference.

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

Antenna

Cable TV
Wall Jack Panel

RF Coaxial Wire
(75 ohm)

RF Coaxial Wire
(75 ohm)

PAGE 10

Cable Box Connections

Locate the output jack on the back of
your cable box. Connect this to the
Antenna jack on the back of your TV.

Or find the composite video and audio
jacks on the back of your cable box, and
connect them following the instructions
provided with your equipment.
This can be combined with any other
equipment you may want to hook up.

1

In

Output
Switch

Out

3 4

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

Audio

TV

VCR

L

R

Video

Cable TV
Wall Jack Panel

RF Coaxial Wire
(75 ohm)

Cable Box

If you’re using a cable box, leave the TV on
channel 3 or 4 and use your cable box to
change channels.

PAGE 11

1

VCR Connections

Locate the Antenna jack on the
back of your TV. Connect this to
RF out jack on the back of your
VCR.

Or, find the composite video and
audio jacks on the back of your
VCR, and connect them following
the instructions provided with
your equipment.

You may connect either the com­posite video or the S-Video cables
to your TV. (Do not connect both
the composite and the S-Video
cables. In the event that you con­nect both composite and the S­Video cables, only the S-Video will
work.)

To hear stereo sound from cable or your VCR,
you will need to connect A/V cables as well as
the wire that runs from the VCR to your TV.

If you want to receive your signals on Channel
3 or 4, locate the Out to TV jack on your VCR.
Connect a cable from the Out to TV jack to the
Antenna In jack on the back of your TV.

After connecting external equipment to the TV,
don’t display a still picture for a long time on
the screen. Doing so may damage the TV
screen.

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

In

Out

Audio

L

R

Video

3 4

S-Video

Output
Switch

Antenna

RF Coaxial Wire

(75 ohm)

Round Wire
(75 ohm)

A/V cables
not included
with TV

VCR

Back AV Panel

Cable TV
Wall Jack Panel

PAGE 12

DVD Player

Mini glossary

COMPONENT VIDEO Some video equipment uses three separate lines (Y, P

B, PR) to more precisely reproduce images. Your video equipment manual

will explain how this relates to your equipment.

Find the audio and component or
S-Video jacks on the back of your
DVD Player and connect them fol­lowing the instructions provided
with your equipment.

You may connect either the com­posite video or the S-Video cables
to your TV. Do not connect both
the composite and the S-Video.

1

Component 1 (or 2) Input

Y PB PR

1920X1080i

1280X720p

720X480p

720X480i

Component input jacks

on the Monitor

Y

PB

PR

Video output jacks
on DVD player

Y
Y
Y
Y

Pb

B-Y

Cb
PB

Pr

R-Y

Cr
P

R

• Component Input ports

Connect DVD player jacks to Monitor
Component input jacks as indicated below.

A/V Cables
Not included
with TV

DVD Player

Back AV Panel

Some high-end DVD players use a
picture reproduction system
called “component video.” If
your DVD player has component
output, use the connectors
marked “Component 1/2” on the
jack panel. Please refer to your
DVD manual for proper installa­tion.

Dolby Digital

Audio

Out

LR

Component Video

S-Video

PC/DTV
(XGA
/480p
/720p
/1080i)

DVI INPUT

RGB INPUT

PC/DTV
(XGA

S-VIDEO

/480p
/720p

C
A
L
I
B
R
A
T
I
O
N

COMPONENT

INPUT2 INPUT1

Y

PB

P

R

(L)

AUDIO

(R)

DTV/DVD INPUT

/1080i)

RGB/DVI INPUT

(L)

AUDIO

(R)

AUDIO
CENTER

MODE IN

(L)

AUDIO

(R)

MONITOR

VIDEO

INPUT 2

VIDEO

INPUT 1

VIDEO

(L)

AUDIO

(R)

OUT

MONO

A

V

U

A

D

R

I

I

O

A
B

O

L

U

E

T

PAGE 13

RGB-DTV/DVI-DTV Input

Find the audio and Y, PB, PR/RGB/DVI jacks
on the back of your DBS receiver and con­nect them following the instructions provid­ed with your equipment.

Connect these cables to your TV as shown.

1

2

The DTV shows the sharpest picture in 720p mode.

Select RGB-DTV Source and press ENTER. Use UP/DOWN arrows to
select the desired options (H-Position/ V-Position/Phase) and then
use LEFT/RIGHT arrows to make appropriate adjustments.

C
A
L

I
B
R
A
T

I
O
N

PC/DTV
(XGA
/480p
/720p
/1080i)

P

R

DVI INPUT

DTV/DVD INPUT

COMPONENT

INPUT2 INPUT1

PB

Y

(R)

(L)

AUDIO

Audio
L R

Component Out

Y Pb Pr

Dolby Digital

Out

C
A
L
I
B
R
A
T
I
O
N

PC/DTV
(XGA
/480p
/720p
/1080i)

AUDIO
CENTER

MODE IN

P

R

DVI INPUT

DTV/DVD INPUT

COMPONENT

INPUT2 INPUT1

PB

Y

PC/DTV
(XGA
/480p
/720p
/1080i)

RGB INPUT

RGB/DVI INPUT

(R)

(L)

AUDIO

(R)

(L)

AUDIO

(R)

(L)

AUDIO

V
A
R
I
A
B
L
E

A
U
D
I
O

O
U
T

Audio
L R

Dolby Digital

Out

HD-SET TOP

1920x1080i

1280x720P

720x480P

RGB-DTV/DVI-DTV Input

Signal

480i
480p
720p

1080i

Component1

Yes
Yes
Yes
Yes

Component2

Yes
Yes
Yes
Yes

RGB/DVI-DTV

No
Yes
Yes
Yes

This TV supports HDCP (High-bandwidth Digital Content
Protection) protocol for DVI-DTV (480p, 720p, 1080i) mode.

DBS Receiver

DBS Receiver

A/V Cables
Not included
with TV

A/V Cables
Not included
with TV

In RGB-DTV mode, H-Position/ V-Position/Phase are not adjustable if
you choose either the POP or Twin picture modes.

or

PAGE 14

RGB-PC/DVI-PC Input

Find the audio and RGB or DVI jacks on the
back of your PC and then connect them fol­lowing the instructions provided with your
equipment.

Connect these cables to your TV as shown.

1

2

Synchronization input form: Signals are separate.

In DVI-PC mode, adjustments are only Vertical size,
and Horizontal size.

C
A
L
I
B
R
A
T
I
O
N

PC/DTV
(XGA
/480p
/720p
/1080i)

AUDIO

CENTER

MODE IN

P

R

DVI INPUT

DTV/DVD INPUT

COMPONENT

INPUT2 INPUT1

PB

Y

PC/DTV
(XGA
/480p
/720p
/1080i)

RGB INPUT

RGB/DVI INPUT

(R)

(L)

AUDIO

(R)

(L)

AUDIO

(R)

(L)

AUDIO

V
A
R
I
A
B
L
E

A
U
D
I
O

O
U
T

MODE Resolution Horizontal Vertical

640x350 31.5KHz 70Hz
640x480 31.5KHz 60Hz
640x480 37.9KHz 72Hz
640x480 37.5KHz 75Hz
800x600 35.2KHz 56Hz
800x600 37.9KHz 60Hz
800x600 48.1KHz 72Hz

800x600 46.9KHz 75Hz
1024x768 48.4KHz 60Hz
1024x768 56.5KHz 70Hz
1024x768 60.0KHz 75Hz

SVGA

VGA

Text

XGA

RGB-PC/DVI-PC Input

Select RGB-PC Source and press ENTER. Use UP/DOWN arrows to
select the desired options (H-Position/V-Position/H-Size/V­Size/Phase) and then use LEFT/RIGHT arrow to make appropriate
adjustments.

-

Horizontal position, Vertical position, Horizontal size, and Vertical

size: Based on the input mode (resolution), the adjustment

ranges may change.

-

PHASE: Removes any horizontal noise and clears up or sharpens

the character images. Adjustment range is -15 ~ + 15.

Computer

In RGB-PC/DVI-PC modes, for POP or Twin screen, H­Position/V-Position/H-Size/V-Size/Phase are not
adjustable.

PAGE 15

External Stereo Connections

1

2

Locate both Variable Audio Out
jacks on the back of your TV and
the Left/Right audio input jacks
on the back of your stereo's
amplifier.

Connect these jacks, making sure
that they are connected correctly.
(red=Right, white=Left.)

Adjust the sound on your stereo,
according to directions provided
with the amplifier.

3

Connect Left/Right Variable Audio Output to an external Audio Amplifier System.

C

A

L

I
B
R
A

T

I
O
N

PC/DTV
(XGA
/480p
/720p
/1080i)

AUDIO

CENTER

MODE IN

P

R

DVI INPUT

DTV/DVD INPUT

COMPONENT

INPUT2 INPUT1

PB

Y

PC/DTV
(XGA
/480p
/720p
/1080i)

RGB INPUT

RGB/DVI INPUT

(R)

(L)

AUDIO

(R)

(L)

AUDIO

(R)

(L)

AUDIO

V
A
R
I
A
B
L
E

A
U
D
I
O

O
U
T

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

Analog stereo amplifier

A/V cables
not included
with TV

PAGE 16

Home Theater: Speaker Layout

sub-woofer

right
speaker

left

speaker

surround

sound

speaker

surround
sound
speaker

This is a typical speaker layout.
Any number of other speaker setups
are possible, and some changes may
be needed to maximize your sound.
However, a Dolby Digital Receiver is
required to hear 5.1 channel audio.

Left and right speakers on each
side of the TV enhance separation.
The TV's sound optional hookup
“center mode in,” makes the dialog
sound as though it’s coming directly
from the TV. The rear surround
sound speakers provide
the majority of other sounds, like
those from special effects in movies.
Your sub-woofer generates ultra-low
frequency sound, for rumbling
low-end audio.

Sound is affected by
speaker placement, so
make sure nothing is in
front of the speakers, and
that they are aimed in
appropriate directions.

You have the option of
turning the TV speakers on
or off.

PAGE 17

Monitor Out Setup

Your TV has a special signal output capa­bility which allows you to hook up a sec­ond TV or monitor.

Just connect the second TV or monitor to
the MONITOR OUT Audio/Video jacks locat­ed on the back of your TV. See the
Operating Manual of the second TV or
monitor for further details regarding that
device’s input settings.

1

2

C
A
L
I
B
R
A
T
I
O
N

PC/DTV
(XGA
/480p
/720p
/1080i)

AUDIO

CENTER

MODE IN

P

R

DVI INPUT

DTV/DVD INPUT

COMPONENT

INPUT2 INPUT1

PB

Y

PC/DTV
(XGA
/480p
/720p
/1080i)

RGB INPUT

RGB/DVI INPUT

(R)

(L)

AUDIO

(R)

(L)

AUDIO

(R)

(L)

AUDIO

V
A
R
I
A
B
L
E

A
U
D
I
O

O
U
T

MONITOR

OUT

VIDEO

INPUT 2

VIDEO

INPUT 1

S-VIDEO

(R)

(L)

AUDIO

VIDEO

MONO

+75 Ω

ANT IN

Audio

Video

S-Video

PB

Component 1 - 2, RGB-DTV/PC, and DVI-DTV/PC
input sources for main picture cannot be used
for Monitor Out.

A/V Cables

Not included

with TV

Second TV

PAGE 18

Remote Control Functions in TV Mode

1 2 3

4 5 6

7 8 9

0

TV

MODE

LIGHT

POWER

TV/VIDEO

DVI

RGB

VCR

CABLE

DVD

SAT

MUTE

SWAPPIPCH- PIPCH+

PIP

RATIO

RECORD

STOP

PAUSE

REW

PLAY

FF

MENU EXIT

CC FREEZE

PIP INPUT

VOL

CH

SURF

SAP

VIDEO

COMP2COMP1

FRONT

SKIP

ENTER

FLASHBK

SURF

Scrolls the Surf channel list.

MENU

Brings up the main menu

to the screen.

EXIT

Clears all on-screen displays
and returns to TV viewing
from any menu.

FREEZE

Captures and freezes the currently­viewed main picture.

VIDEO

Adjusts the factory preset pic­ture according to the room.

PIPCH+

Changes to next higher PIP
channel.

SWAP

Switches the picture from
PIP, POP, or twin picture to
the main screen.

MUTE

Switches the sound on or off

THUMBSTICK

Allows you to navigate the on-screen

menus and to adjust the system set-

tings and preferences, by moving to

an option with

F G

and selecting the

highlighted option with .

TV/VIDEO

Selects: Analog, Video1, Video2,

Front video, Component1-2, RGB,

and DVI input sources.

MODE

Selects the remote operating mode:

TV, VCR, Cable, DVD and Satellite.
Select other operating modes, for

the remote to control external

devices.

FRONT

Selects the front video signal if a

device, such as a camcorder or

game player, is connected to the

front video input jack.

DVI

Selects: DVI-DTV and DVI-PC
input sources.

SAP

Selects: Mono, Stereo, and SAP.

PIPCH-

Changes to next lower

PIP channel

PIP

Toggles between PIP, POP

(Picture-outside-Picture) and

Twin picture mode.

LIGHT

Illuminates the remote control
keys.

INDICATOR LIGHTS

Show active remote mode
every time any button is
pressed.

D
E